openkylin
/
libvirt
mirror of https://gitee.com/openkylin/libvirt.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
libvirt/tests/networkxml2xmlout/routed-network.xml

12 lines
330 B
XML
Raw Normal View History

tests: Add network XML to XML tests.
2009-10-09 20:47:43 +08:00
<network>
<name>local</name>
<uuid>81ff0d90-c91e-6742-64da-4a736edb9a9b</uuid>
conf: support abstracted interface info in network XML The network XML is updated in the following ways: 1) The <forward> element can now contain a list of forward interfaces: <forward .... > <interface dev='eth10'/> <interface dev='eth11'/> <interface dev='eth12'/> <interface dev='eth13'/> </forward> The first of these takes the place of the dev attribute that is normally in <forward> - when defining a network you can specify either one, and on output both will be present. If you specify both on input, they must match. 2) In addition to forward modes of 'nat' and 'route', these new modes are supported: private, passthrough, vepa - when this network is referenced by a domain's interface, it will have the same effect as if the interface had been defined as type='direct', e.g.: <interface type='direct'> <source mode='${mode}' dev='${dev}> ... </interface> where ${mode} is one of the three new modes, and ${dev} is an interface selected from the list given in <forward>. bridge - if a <forward> dev (or multiple devs) is defined, and forward mode is 'bridge' this is just like the modes 'private', 'passthrough', and 'vepa' above. If there is no forward dev specified but a bridge name is given (e.g. "<bridge name='br0'/>"), then guest interfaces using this network will use libvirt's "host bridge" mode, equivalent to this: <interface type='bridge'> <source bridge='${bridge-name}'/> ... </interface> 3) A network can have multiple <portgroup> elements, which may be selected by the guest interface definition (by adding "portgroup='${name}'" in the <source> element along with the network name). Currently a portgroup can only contain a virtportprofile, but the intent is that other configuration items may be put there int the future (e.g. bandwidth config). When building a guest's interface, if the <interface> XML itself has no virtportprofile, and if the requested network has a portgroup with a name matching the name given in the <interface> (or if one of the network's portgroups is marked with the "default='yes'" attribute), the virtportprofile from that portgroup will be used by the interface. 4) A network can have a virtportprofile defined at the top level, which will be used by a guest interface when connecting in one of the 'direct' modes if the guest interface XML itself hasn't specified any virtportprofile, and if there are also no matching portgroups on the network.
2011-07-20 11:01:09 +08:00
<forward dev='eth1' mode='route'>
<interface dev='eth1'/>
</forward>
network: allow configuring firewalld zone for virtual network bridge device Since we're setting the zone anyway, it will be useful to allow setting a different (custom) zone for each network. This will be done by adding a "zone" attribute to the "bridge" element, e.g.: ... <bridge name='virbr0' zone='myzone'/> ... If a zone is specified in the config and it can't be honored, this will be an error. Signed-off-by: Laine Stump <laine@laine.org> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
2019-01-10 05:51:31 +08:00
<bridge name='virbr1' zone='myzone' stp='on' delay='0'/>
util: Change virMacAddrFormat to lowercase hex characters The domain XML generator creates the mac addres strings with lowercase strings with a separate piece of code. This patch changes the formating helper to do the same stuff to allow using it to normalize a string provided by the user. After this change some of the tests that are outputing the mac address will need to be changed.
2013-03-26 18:45:29 +08:00
<mac address='12:34:56:78:9a:bc'/>
tests: Add network XML to XML tests.
2009-10-09 20:47:43 +08:00
<ip address='192.168.122.1' netmask='255.255.255.0'>
</ip>
</network>