Historically the virtio-blk frontend by default enabled SCSI emulation
and tried to do SCSI command passthrough. As this was enabled by default
there's a fallback mechanism in place in cases when the backend doesn't
support SCSI for any reason.
This is not the case when disk type=lun is used with 'scsi-block' via
'virtio-scsi'.
We did not restrict configurations when the user picks 'qcow2' or any
other format as format of the disk, in which case the emulation is
disabled as such configuration doesn't make sense.
This patch unifies the approach so that 'raw' is required both when used
via 'virtio-blk' and 'virtio-scsi' so that the user is presented with
the expected configuration. Note that use of <disk type='lun'> is
already very restrictive as it requires a block device or iSCSI storage.
Additionally the scsi emulation is now deprecated by qemu with
virtio-blk as it conflicts with virtio-1 and the alternative is to use
'virtio-scsi' which performs better and is along for a very long time.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
None of the tests depend on anything that the machine type would
influence. This will allow us to drop the very old machine type from the
non-real-data tests. If something depends on the machine type it should
be tested with real data rather than this hack.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
The '-realtime mlock' cmd line argument was introduced in QEMU
commit v1.5.0-rc0~190 which matches minimal QEMU version we
require. Therefore, the capability will always be present.
Apparently, nearly none of our xml2argv test cases had the
capability hence slightly bigger change under qemuxml2argvdata/.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
By default, qemu user's home dir points to '/' which shouldn't be used
at all. We therefore pass the HOME variable from the current variable
iff not running as SUID, which means that for systemd we never set it.
This patch makes sure, that for system QEMU this is always set to
libDir/<driver>, session mode is left untouched.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
For session mode, only XDG_CACHE_HOME is set, because we want to remain
integrating with services in user session, but for system mode, this
would have become reading/writing to '/' which carries the obvious issue
with permissions (also, '/' is the wrong location in 99.9% cases anyway).
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The field was added in qemu v0.13.0-rc0-731-g1ca4d09ae0 so all supported
qemu versions now use it.
There's a LOT of test fallout as we did not use capabilities close
enough to upstream for many of our tests.
Several tests had a 'bootindex' variant. Since they'd become redundant
they are also removed here.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Implied by QEMU >= 1.2.0.
Delete this one first, because QEMU_CAPS_NODEFCONFIG is only used
when QEMU_CAPS_NO_USER_CONFIG is unsupported.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
We require QEMU >= 1.5.0, assume every QEMU supports it.
Sadly that does not let us trivially drop qemuMonitor's
priv->monJSON bool, because of qemuDomainQemuAttach.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
This makes qemuDomainSupportsNetdev identical to
qemuDomainSupportsNicdev and leaves some code in
qemuDomainAttachNetDevice to be cleaned up later.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Similarly to the previous commit, rename .args files.
The files were renamed using the following commands. From
qemuxml2argvdata:
for i in qemuxml2argv-*.args; do mv $i ${i#qemuxml2argv-}; done
and then (to fix broken symlinks) from qemuxml2argvdata and
qemuxml2xmloutdata:
for i in $(find . -xtype l); do \
ln -sf $(readlink $i | sed 's/qemuxml2argv-//') $i;
done
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Peter Krempa