dnsmasq documentation says that the *IPv4* prefix/network
address/broadcast address sent to dhcp clients will be automatically
determined by dnsmasq by looking at the interface it's listening on,
so the original libvirt code did not add a netmask to the dnsmasq
commandline (or later, the dnsmasq conf file).
For *IPv6* however, dnsmasq apparently cannot automatically determine
the prefix (functionally the same as a netmask), and it must be
explicitly provided in the conf file (as a part of the dhcp-range
option). So many years after IPv4 DHCP support had been added, when
IPv6 dhcp support was added the prefix was included at the end of the
dhcp-range setting, but only for IPv6.
A user had reported a bug on a host where one of the interfaces was a
superset of the libvirt network where dhcp is needed (e.g., the host's
ethernet is 10.0.0.20/8, and the libvirt network is 10.10.0.1/24). For
some reason dnsmasq was supplying the netmask for the /8 network to
clients requesting an address on the /24 interface.
This seems like a bug in dnsmasq, but even if/when it gets fixed
there, it looks like there is no harm in just always adding the
netmask to all IPv4 dhcp-range options similar to how prefix is added
to all IPv6 dhcp-range options.
Signed-off-by: Laine Stump <laine@laine.org>
Reviewed-by: John Ferlan <jferlan@redhat.com>
The dnsmasq man page recommends that dhcp-authoritative "should be
set when dnsmasq is definitely the only DHCP server on a network".
This is the case for libvirt-managed virtual networks.
The effect of this is that VMs that fail to renew their DHCP lease
in time (e.g. if the VM or host is suspended) will be able to
re-acquire the lease even if it's expired, unless the IP address has
been taken by some other host. This avoids various annoyances caused
by changing VM IP addresses.
According to the dnsmasq manpage, the netmask for IPv4 address ranges
will be auto-deteremined from the interface dnsmasq is listening on,
but it can't do this for IPv6 for some reason - it instead assumes a
network prefix of 64 for all IPv6 address ranges. If this is
incorrect, dnsmasq will refuse to give out an address to clients,
instead logging this message:
dnsmasq-dhcp[2380]: no address range available for DHCPv6 request via virbr0
The solution is for libvirt to add ",$prefix" to all IPv6 dhcp-range
arguments when building the dnsmasq.conf file.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1033739
The previous patch fixed "forwardPlainNames" so that it really is
doing only what is intended, but left the default to be
"forwardPlainNames='no'". Discussion around the initial version of
that patch led to the decision that the default should instead be
"forwardPlainNames='yes'" (i.e. the original behavior before commit
f3886825). This patch makes that change to the default.
This patch resolves the problem reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=886663
The source of the problem was the fix for CVE 2011-3411:
https://bugzilla.redhat.com/show_bug.cgi?id=833033
which was originally committed upstream in commit
753ff83a50. That commit improperly
removed the "--except-interface lo" from dnsmasq commandlines when
--bind-dynamic was used (based on comments in the latter bug).
It turns out that the problem reported in the CVE could be eliminated
without removing "--except-interface lo", and removing it actually
caused each instance of dnsmasq to listen on localhost on port 53,
which created a new problem:
If another instance of dnsmasq using "bind-interfaces" (instead of
"bind-dynamic") had already been started (or if another instance
started later used "bind-dynamic"), this wouldn't have any immediately
visible ill effects, but if you tried to start another dnsmasq
instance using "bind-interfaces" *after* starting any libvirt
networks, the new dnsmasq would fail to start, because there was
already another process listening on port 53.
(Subsequent to the CVE fix, another patch changed the network driver
to put dnsmasq options in a conf file rather than directly on the
dnsmasq commandline, but preserved the same options.)
This patch changes the network driver to *always* add
"except-interface=lo" to dnsmasq conf files, regardless of whether we use
bind-dynamic or bind-interfaces. This way no libvirt dnsmasq instances
are listening on localhost (and the CVE is still fixed).
The actual code change is miniscule, but must be propogated through all
of the test files as well.
I noticed that /var/lib/libvirt/dnsmasq/*.conf used the wrong word;
it was intended to match the wording in src/util/xml.c.
* src/network/bridge_driver.c (networkDnsmasqConfContents): Fix typo.
* tests/networkxml2confdata/*.conf: Update accordingly.
This patch changes how parameters are passed to dnsmasq. Instead of
being on the command line, the parameters are put into a file (one
parameter per line) and a commandline --conf-file= specifies the
location of the file. The file is located in the same directory as
the leases file.
Putting the dnsmasq parameters into a configuration file
allows them to be examined and more easily understood than
examining the command lines displayed by "ps ax". This is
especially true when a number of networks have been started.
When the use of dnsmasq was originally done, the required command line
was simple, but it has gotten more complicated over time and will
likely become even more complicated in the future.
Note: The test conf files have all been renamed .conf instead of
.argv, and tests/networkxml2xmlargvdata was moved to
tests/networkxml2xmlconfdata.
Laine Stump