* src/qemu/qemu_conf.c: add the ",readonly=on" for read-only disks
and also parse it back in qemuParseCommandLineDisk()
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.args
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.xml:
add a specific regression test
The current code for "nodeinfo" is pretty naive
about socket and thread information. To determine the
sockets, it just takes the number of cpus and divides
by the number of cores. For the thread count, it always
sets it to 1. With more recent Intel machines, however,
hyperthreading is again an option, meaning that these
heuristics no longer work and give bogus numbers. This
patch goes through /sys to get the additional
information so we properly report it.
Note that I had to edit the tests not to report on
socket and thread counts, since these are determined
dynamically now.
v2: As pointed out by Eric Blake, gnulib provides
count-one-bits (which is LGPLv2+). Use it instead
of a hand-coded popcnt.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Allow an arbitrary timezone with QEMU by setting the $TZ environment
variable when launching QEMU
* src/qemu/qemu_conf.c: Set TZ environment variable if a timezone
is requested
* tests/qemuxml2argvtest.c: Add test case for timezones
* tests/qemuxml2argvdata/qemuxml2argv-clock-france.xml,
tests/qemuxml2argvdata/qemuxml2argv-clock-france.args: Data
for timezone tests
This allows QEMU guests to be started with an arbitrary clock
offset
The test case can't actually be enabled, since QEMU argv expects
an absolute timestring, and this will obviously change every
time the test runs :-( Hopefully QEMU will allow a relative
time offset in the future.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Use the -rtc arg
if available to support variable clock offset mode
* tests/qemuhelptest.c: Add QEMUD_CMD_FLAG_RTC for qemu 0.12.1
* qemuxml2argvdata/qemuxml2argv-clock-variable.args,
qemuxml2argvdata/qemuxml2argv-clock-variable.xml,
qemuxml2argvtest.c: Test case, except we can't actually enable
it yet.
The daemon-conf test would fail on my system if there was a system libvirtd
running. In the course of troubleshooting that problem, I discovered that the
daemon-conf script would always fail if run by itself because it found the line:
\# that each "PARAMETER = VALUE" line in this file have the parameter
which it mistook for a line containing a parameter. I have changed the test to
avoid mistaking a line containing \"PARAMETER = VALUE\" for a parameter line.
The corrupted config tests turned out to be failing because the test daemon was
discovering the pid file from the running daemon and exiting before it processed
the test config file. Specifying the pid file for the corrupt config tests in
the same way as for the valid config test solved that problem.
Support virtio-serial controller and virtio channel in QEMU backend.
Will output
the following for virtio-serial controller:
-device
virtio-serial-pci,id=virtio-serial0,bus=pci.0,addr=0x4,max_ports=16,vectors=4
and the following for a virtio channel:
-chardev pty,id=channel0 \
-device
virtserialport,bus=virtio-serial0.0,chardev=channel0,name=org.linux-kvm.port.0
* src/qemu/qemu_conf.c: Add argument output for virtio
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args: Add test for
QEMU command line generation
Add support for virtio-serial by defining a new 'virtio' channel target type
and a virtio-serial controller. Allows the following to be specified in a
domain:
<controller type='virtio-serial' index='0' ports='16' vectors='4'/>
<channel type='pty'>
<target type='virtio' name='org.linux-kvm.port.0'/>
<address type='virtio-serial' controller='0' bus='0'/>
</channel>
* docs/schemas/domain.rng: Add virtio-serial controller and virtio
channel type.
* src/conf/domain_conf.[ch]: Domain parsing/serialization for
virtio-serial controller and virtio channel.
* tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: add domain xml
parsing test
* src/libvirt_private.syms src/qemu/qemu_conf.c:
virDomainDefAddDiskControllers() renamed to
virDomainDefAddImplicitControllers()
Use the ATTRIBUTE_NONNULL annotation to mark some virConnectPtr
args as mandatory non-null so the compiler can warn of mistakes
* src/conf/domain_event.h: All virConnectPtr args must be non-null
* src/qemu/qemu_conf.h: qemudBuildCommandLine and
qemudNetworkIfaceConnect() must be given non-null connection
* tests/qemuxml2argvtest.c: Provide a non-null (dummy) connection to
qemudBuildCommandLine()
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in interface_conf.{h,c} and update all callers to
match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in storage_conf.{h,c} and storage_encryption_conf.{h,c}
and update all callers to match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in node_device_conf.{h,c} and update all callers to
match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in network_conf.{h,c} and update all callers to
match
The QEMU flags are commonly stored as a signed or unsigned int,
allowing only 31 flags. This limit is rather close, so to aid
future patches, change it to a 64-bit int
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c,
tests/qemuargv2xmltest.c, tests/qemuhelptest.c, tests/qemuxml2argvtest.c:
Use 'unsigned long long' for QEMU flags
To allow devices to be hot(un-)plugged it is neccessary to ensure
they all have a unique device aliases. This fixes the hotplug
methods to assign device aliases before invoking the monitor
commands which need them
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Expose methods
for assigning device aliases for disks, host devices and
controllers
* src/qemu/qemu_driver.c: Assign device aliases when hotplugging
all types of device
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address-device.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-address-device.args:
Update for changed hostdev naming scheme
The current way of assigning names to the host network backend and
NIC device in QEMU was over complicated, by varying naming scheme
based on the NIC model and backend type. This simplifies the naming
to simply be 'net0' and 'hostnet0', allowing code to easily determine
the host network name and vlan based off the primary device alias
name 'net0'. This in turn allows removal of alot of QEMU specific
code from the XML parser, and makes it easier to assign new unique
names for NICs that are hotplugged
* src/conf/domain_conf.c, src/conf/domain_conf.h: Remove hostnet_name
and vlan fields from virNetworkDefPtr
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c:
Use a single network alias naming scheme regardless of NIC type
or backend type. Determine VLANs from the alias name.
* tests/qemuxml2argvdata/qemuxml2argv-net-eth-names.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args: Update
for new simpler naming scheme
The QEMU 0.12.x tree has the -netdev command line argument, but not
corresponding monitor command. We can't enable the former, without
the latter since it will break hotplug/unplug.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Disable -netdev usage
until 0.13 at earliest
* tests/qemuxml2argvtest.c: Add test for -netdev syntax
* tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.xml: Test
data files for -netdev syntax
The current QEMU code allocates PCI addresses incrementally starting
at 4. This is not satisfactory because the user may have given some
addresses in their XML config, which need to be skipped over when
allocating addresses to remaining devices.
It is thus neccessary to maintain a list of already allocated PCI
addresses and then only allocate ones that remain unused. This is
also required for domain device hotplug to work properly later.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Add APIs for creating
list of existing PCI addresses, and allocating new addresses.
Refactor address assignment to use this code
* src/qemu/qemu_driver.c: Pull PCI address assignment up into the
qemuStartVMDaemon() method, as a prelude to moving it into the
'define' method. Update list of allocated addresses when connecting
to a running VM at daemon startup.
* tests/qemuxml2argvtest.c, tests/qemuargv2xmltest.c,
tests/qemuxml2xmltest.c: Remove USB product test since all
passthrough is done based on address
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.xml: Kil
unused data files
The test expected all environment variables copied in qemudBuildCommandLine
to have known values. So all of them have to be either set to a known value
or be unset. SDL_VIDEODRIVER and QEMU_AUDIO_DRV are not handled at all but
should be handled. Unset both, otherwise the test will fail if they are set
in the testing environment.
* src/qemu/qemu_conf.c: add a comment about copied environment variables
and qemuxml2argvtest
* tests/qemuxml2argvtest.c: unset SDL_VIDEODRIVER and QEMU_AUDIO_DRV
The RNG now supports IPv6 and bonds attached to bridges, along with
some other minor tweaks. All test files from netcf have been copied to
the test directory and added to the xml2xml and schema tests (and they
all pass, of course ;-)
QEMU's command line equivalent for the following domain XML fragment
<vcpus>2</vcpus>
<cpu ...>
...
<topology sockets='1' cores='2', threads='1'/>
</cpu>
is
-smp 2,sockets=1,cores=2,threads=1
This syntax was introduced in QEMU-0.12.
Version 2 changes:
- -smp argument build split into a separate function
- always add ",sockets=S,cores=C,threads=T" to -smp if qemu supports it
- use qemuParseCommandLineKeywords for command line parsing
Version 3 changes:
- ADD_ARG_LIT => ADD_ARG and line reordering in qemudBuildCommandLine
- rebased
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Replace
-balloon virtio
With
-device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x3
This allows it to get correct assigned PCI address as declared in
previous patch
* src/qemu/qemu_conf.c: Convert Virtio ballon to -device and
give it an explicit PCI address
* tests/qemuxml2argvdata/qemuxml2argv-*args: Add in virtio balloon
where appropriate
Instead of relying on QEMU to assign PCI addresses and then querying
them with 'info pci', manually assign all PCI addresses before starting
the guest. These addresses are not stable across reboots. That will
come in a later patch
NB, the PIIX3 (IDE, FDC, ISA-Bridge) will always have slot 1 and
VGA will always have slot 2. We declare the Virtio Balloon gets
slot 3, and then all remaining slots are for configured devices.
* src/qemu/qemu_conf.c: If -device is supported, then assign all PCI
addresses when building the command line
* src/qemu/qemu_driver.c: Don't query monitor for PCI addresses if
they have already been assigned
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-sound-device.args,
tests/qemuxml2argvdata/qemuxml2argv-watchdog-device.args: Update
to include PCI slot/bus information
QEMU always configures a VGA card. If no video card is included in
the libvirt XML, it is neccessary to explicitly turn off the default
using -vga none
* src/qemu/qemu_conf.c: Pass -vga none if no video card is configured
* tests/qemuargv2xmltest.c, tests/qemuxml2argvtest.c: Test for
handling -vga none.
* tests/qemuxml2argvdata/qemuxml2argv-nographics-vga.args,
tests/qemuxml2argvdata/qemuxml2argv-nographics-vga.xml: Test
data files
Not all QEMU builds default to SDL graphics for their display.
Newer QEMU now has an explicit -sdl flag, which we can use to
explicitly request SDL intead of relying on the default. This
protects libvirt against unexpected changes in graphics default
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Probe for -sdl
flag and use it if it is found
* tests/qemuhelptest.c: Add SDL flag to tests
The old syntax was
-chardev SOMECONFIG
-nic user,guestfwd=tcp:IP:PORT-chardev:CHARDEV
The new syntax is
-chardev SOMECONFIG
-netdev user,guestfwd=tcp:IP:PORT,chardev=ID,id=user-ID
The old syntax was
-usbdevice host:PRODUCT:VENDOR
Or
-usbdevice host:BUS.DEV
The new syntax is
-device usb-host,product=PRODUCT,vendor=VENDOR
Or
-device usb-host,hostbus=BUS,hostaddr=DEV
The previous syntax was severely limited in its options
-usbdevice disk:/home/berrange/output.img
The new syntax is the same as for other disk types
-drive file=/home/berrange/output.img,if=none,id=usb-1,index=1
-device usb-storage,drive=usb-1
Again, the index= arg is wrong here, and will be removed in a
later merge
The current syntax uses a pair of args
-net nic,macaddr=52:54:00:56:6c:55,vlan=3,model=pcnet,name=pcnet.0
-net user,vlan=3,name=user.0
The new syntax does not need the vlan craziness anymore, and
so has a simplified pair of args
-netdev user,id=user.0
-device pcnet,netdev=user.0,id=pcnet.0,mac=52:54:00:56:6c:55,addr=<PCI SLOT>
The current syntax for audio devices is a horrible multiplexed
arg
-soundhw sb16,pcspk,ac97
The new syntax is
-device sb16,id=sound0
or
-device AC97,id=sound1,addr=<PCI SLOT>
NB, pcspk still uses the old -soundhw syntax
The current character device syntax uses either
-serial tty,path=/dev/ttyS2
Or
-chardev tty,id=serial0,path=/dev/ttyS2 -serial chardev:serial0
With the new -device support, we now prefer
-chardev file,id=serial0,path=/tmp/serial.log -device isa-serial,chardev=serial0
This patch changes the existing -chardev syntax to use this new
scheme, and fallbacks to the old plain -serial syntax for old
QEMU.
The monitor device changes to
-chardev socket,id=monitor,path=/tmp/test-monitor,server,nowait -mon chardev=monitor
In addition, this patch adds --nodefaults, which kills off the
default serial, parallel, vga and nic devices. THis avoids the
need for us to explicitly turn each off
Probe for the new -device flag and if available set the -nodefaults
flag, instead of using -net none, -serial none or -parallel none.
Other device types will be converted to use -device in later patches.
The -nodefaults flag will help avoid unwelcome surprises from future
QEMU releases
* src/qemu/qemu_conf.c: Probe for -device. Add -nodefaults flag.
Remove -net none, -serial none or -parallel none
* src/qemu/qemu_conf.h: Define QEMU_CMD_FLAG_DEVICE
* tests/qemuhelpdata/qemu-0.12.1: New data file for 0.12.1 QEMU
* tests/qemuhelptest.c: Test feature extraction from 0.12.1 QEMU
Existing applications using libvirt are not aware of the disk
controller concept. Thus, after parsing the <disk> definitions
in the XML, it is neccessary to create <controller> elements
to satisfy all requested disks, as per their defined drive
addresses
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/libvirt_private.syms: Add virDomainDefAddDiskControllers()
method for populating disk controllers, and call it after
parsing disk definitions.
* src/qemu/qemu_conf.c: Call virDomainDefAddDiskControllers()
when doing ARGV -> XML conversion
* tests/qemuxml2argvdata/qemuxml2argv*.xml: Add disk controller
data to all data files which don't have it already
It is perfectly acceptable to have multiple sound devices of
same type in guest configuration. If the underlying hypervisor
does not like this, it is its job to complain, not the XML
parser's
* src/conf/domain_conf.c: Remove hack which deleted duplicated
sound device models.
* tests/xml2sexprdata/xml2sexpr-fv-sound.xml: Remove duplicate
models
The latter is not officially "wrong", but *is* terribly anachronistic.
I think automake documentation or comments call that syntax obsolescent.
* cfg.mk (_makefile_at_at_check_exceptions): Exempt @SCHEMADIR@
and @SYSCONFDIR@ uses -- there are no Makefile variables for those.
* docs/Makefile.am: Use $(INSTALL), not @INSTALL@.
* examples/dominfo/Makefile.am: Similar.
* examples/domsuspend/Makefile.am: Similar.
* proxy/Makefile.am: Similar.
* python/Makefile.am: Similar.
* python/tests/Makefile.am: Similar.
* src/Makefile.am: Similar.
* tests/Makefile.am: Similar.
* src/conf/domain_conf.c: add defaults for the video device
* src/esx/esx_vmx.[ch]: add VNC support to the VMX handling
* tests/vmx2xmltest.c, tests/xml2vmxtest.c: add tests for the VNC support
The current code for using -drive simply sets the -drive 'index'
parameter. QEMU internally converts this to bus/unit depending
on the type of drive. This does not give us precise control over
the bus/unit assignment though. This change switches over to make
libvirt explicitly calculate the bus/unit number.
In addition bus/unit/index are actually irrelevant for VirtIO
disks, since each virtio disk is a separate PCI device. No disk
controller is involved.
Doing the conversion to bus/unit in libvirt allows us to correctly
attach SCSI controllers when required.
* src/qemu/qemu_conf.c: Specify bus/unit instead of index for
disks
* tests/qemuxml2argvdata/qemuxml2argv-disk*.args: Switch over from
using index=NNNN, to bus=NN, unit=NN for SCSI/IDE/Floppy disks
Jim Meyering