it was using atoi direct without checking leading to confusion
in case of flag error for example with -c
* tools/virsh.c: vshParseArgv() use virStrToLong_i and remove the
unchecked atoi used to parse teh parameter
This patch attempts to take advantage of a newly added netfilter
module to correct for a problem with some guest DHCP client
implementations when used in conjunction with a DHCP server run on the
host systems with packet checksum offloading enabled.
The problem is that, when the guest uses a RAW socket to read the DHCP
response packets, the checksum hasn't yet been fixed by the IP stack,
so it is incorrect.
The fix implemented here is to add a rule to the POSTROUTING chain of
the mangle table in iptables that fixes up the checksum for packets on
the virtual network's bridge that are destined for the bootpc port (ie
"dhcpc", ie port 68) port on the guest.
Only very new versions of iptables will have this support (it will be
in the next upstream release), so a failure to add this rule only
results in a warning message. The iptables patch is here:
http://patchwork.ozlabs.org/patch/58525/
A corresponding kernel module patch is also required (the backend of
the iptables patch) and that will be in the next release of the
kernel.
When trying to assign a PCI device to a guest, we have
to check that all bridges upstream of that device support
ACS. That means that we have to find the parent bridge of
the current device, check for ACS, then find the parent bridge
of that device, check for ACS, etc. As it currently stands,
the code to do this iterates through all PCI devices on the
system, looking for a device that has a range of busses that
included the current device's bus.
That check is not restrictive enough, though. Depending on
how we iterated through the list of PCI devices, we could first
find the *topmost* bridge in the system; since it necessarily had
a range of busses including the current device's bus, we
would only ever check the topmost bridge, and not check
any of the intermediate bridges.
Note that this also caused a fairly serious bug in the
secondary bus reset code, where we could erroneously
find and reset the topmost bus instead of the inner bus.
This patch changes pciGetParentDevice() so that it first
checks if a bridge device's secondary bus exactly matches
the bus of the device we are looking for. If it does, we've
found the correct parent bridge and we are done. If it does not,
then we check to see if this bridge device's busses *include* the
bus of the device we care about. If so, we mark this bridge device
as best, and go on. If we later find another bridge device whose
busses include this device, but is more restrictive, then we
free up the previous best and mark the new one as best. This
algorithm ensures that in the normal case we find the direct
parent, but in the case that the parent bridge secondary bus
is not exactly the same as the device, we still find the
correct bridge.
This patch was tested by me on a 4-port NIC with a
bridge without ACS (where assignment failed), a 4-port
NIC with a bridge with ACS (where assignment succeeded),
and a 2-port NIC with no bridges (where assignment
succeeded).
Signed-off-by: Chris Lalancette <clalance@redhat.com>
When parsing hostdev, the following message would be emitted:
10:17:19.052: error : virDomainHostdevDefParseXML:3748 : internal error unknown node alias
However, alias is appropriately parsed in
virDomainDeviceInfoParseXML anyway. Disable the error message
in the initial XML parsing loop.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
When an openvz domain is defined with virDomainDefineXML,
domain id is set to -1. A call to virDomainGetInfo after
starting the domain would then fail because this invalid
id is passed to openvzGetProcessInfo.
Found by clang. Clang complained that virStorageBackendProbeTarget
could dereference NULL if backingStoreFormat was NULL, but since all
callers passed a valid pointer, I added attributes instead of null
checks.
* src/storage/storage_backend.c
(virStorageBackendQEMUImgBackingFormat): Kill dead store.
* src/storage/storage_backend_fs.c (virStorageBackendProbeTarget):
Likewise. Skip null checks, by adding attributes.
valgrind was complaining that virUUIDParse was depending on
an uninitialized value. Indeed it was; virSetHostUUIDStr()
didn't initialize the dmiuuid buffer to 0's, meaning that
anything after the string read from /sys was uninitialized.
Clear out the dmiuuid buffer before use, and make sure to
always leave a \0 at the end.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Basically the 'boot=on' boot selection device is something present in
KVM but not in upstream QEmu, as a result if we boot a QEmu domain
without KVM acceleration we must disable boot=on ... even if the front
end kvm binary expose that capability in the help page.
* src/qemu/qemu_conf.c: in qemudBuildCommandLine if -no-kvm
is passed, then deactivate QEMUD_CMD_FLAG_DRIVE_BOOT
ADD_ARG_LIT should only be used for literal arguments,
since it duplicates the memory. Since virBufferContentAndReset
is already allocating memory, we should only use ADD_ARG.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
esxVI_WaitForTaskCompletion can take a UUID to lookup the
corresponding domain and check if the current task for it
is blocked by a question. It calls another function to do
this: esxVI_LookupAndHandleVirtualMachineQuestion looks up
the VirtualMachine and checks for a question. If there is
a question it calls esxVI_HandleVirtualMachineQuestion to
handle it.
If there was no question or it has been answered the call
to esxVI_LookupAndHandleVirtualMachineQuestion returns 0.
If any error occurred during the lookup and answering
process -1 is returned. The problem with this is, that -1
is also returned when there was no error but the question
could not be answered. So esxVI_WaitForTaskCompletion cannot
distinguish between this two situations and reports that a
question is blocking the task even when there was actually
another problem.
This inherent problem didn't surface until vSphere 4.1 when
you try to define a new domain. The driver tries to lookup
the domain that is just in the process of being registered.
There seems to be some kind of race condition and the driver
manages to issue a lookup command before the ESX server was
able to register the domain. This used to work before.
Due to the return value problem described above the driver
reported a false error message in that case.
To solve this esxVI_WaitForTaskCompletion now takes an
additional occurrence parameter that describes whether or
not to expect the domain to be existent. Also add a new
parameter to esxVI_LookupAndHandleVirtualMachineQuestion
that allows to distinguish if the call returned -1 because
of an actual error or because the question could not be
answered.
'./autobuild.sh' with lcov installed discovered that our
coverage support has been bit-rotting for a while. This
restores it back to a successful state, although I have
not yet spent any time looking through the resulting files to
look for low-hanging fruit in the unit test coverage front.
* configure.ac: Clear COMPILER_FLAGS at right place.
* Makefile.am (cov): Newer genhtml no longer likes plain -s.
* m4/compiler-flags.m4 (gl_COMPILER_FLAGS): Don't AC_SUBST
COMPILER_FLAGS; it is a shell variable for use in configure only.
* src/Makefile.am (AM_CFLAGS, AM_LDFLAGS): New variables, to make
it easier to provide global flag additions. Use throughout, to
uniformly apply coverage flags.
* .gitignore: Globally ignore gcov output.
* daemon/.gitignore: Simplify.
* src/.gitignore: Likewise.
* tests/.gitignore: Likewise.
The recent switch to enable -Wlogical-op paid off again.
gcc 4.5.0 (rawhide) is smarter than 4.4.4 (Fedora 13).
* src/xen/xend_internal.c (xenDaemonAttachDeviceFlags)
(xenDaemonUpdateDeviceFlags, xenDaemonDetachDeviceFlags): Use
correct operator.
Signed-off-by: Eric Blake <eblake@redhat.com>
src/lxc/veth.c:150: VIR_DEBUG(_("Failed to delete '%s' (%d)"),
src/lxc/veth.c:188: VIR_DEBUG(_("Failed to disable '%s' (%d)"),
maint.mk: do not mark these strings for translation
* src/lxc/veth.c (vethDelete, vethInterfaceUpOrDown): Don't
translate VIR_DEBUG.
Previously, the functions in src/lxc/veth.c could sometimes return
positive values on failure rather than -1. This made accurate error
reporting difficult, and led to one failure to catch an error in a
calling function.
This patch makes all the functions in veth.c consistently return 0 on
success, and -1 on failure. It also fixes up the callers to the veth.c
functions where necessary.
Note that this patch may be related to the bug:
https://bugzilla.redhat.com/show_bug.cgi?id=607496.
It will not fix the bug, but should unveil what happens.
* po/POTFILES.in - add veth.c, which previously had no translatable strings
* src/lxc/lxc_controller.c
* src/lxc/lxc_container.c
* src/lxc/lxc_driver.c - fixup callers to veth.c, and remove error logs,
as they are now done in veth.c
* src/lxc/veth.c - make all functions consistently return -1 on error.
* src/lxc/veth.h - use ATTRIBUTE_NONNULL to protect against NULL args.
This fixes a leak described in
https://bugzilla.redhat.com/show_bug.cgi?id=590073
xenUnifiedDomainInfoList has a pointer to a list of pointers to
xenUnifiedDomain. We were freeing up all the domains, but neglecting
to free the list.
This was found by Paolo Bonzini <pbonzini@redhat.com>.
If detecting the FLR flag of a pci device fails, then we
could run into the situation of trying to close a file
descriptor twice, once in pciInitDevice() and once in pciFreeDevice().
Fix that by removing the pciCloseConfig() in pciInitDevice() and
just letting pciFreeDevice() handle it.
Thanks to Chris Wright for pointing out this problem.
While we are at it, fix an error check. While it would actually
work as-is (since success returns 0), it's still more clear to
check for < 0 (as the rest of the code does).
Signed-off-by: Chris Lalancette <clalance@redhat.com>
All <console> devices now export a <target> type attribute. QEMU defaults
to 'serial', UML defaults to 'uml, xen can be either 'serial' or 'xen'
depending on fullvirt. Understandably there is lots of test fallout.
This will be used to differentiate between a serial vs. virtio console for
QEMU.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
targetType only tracks the actual <target> format we are parsing. Currently
we only fill abide this value for channel devices.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
There is actually a difference between the character device type (serial,
parallel, channel, ...) and the target type (virtio, guestfwd). Currently
they are awkwardly conflated.
Start to pull them apart by renaming targetType -> deviceType. This is
an entirely mechanical change.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Add tests for auto memballon, implicit IDE, SCSI, virtio channel
controllers, and console/serial back compat.
Additionally, an explicit qemuxml2argvtest for scsi disks is added.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
During function test of the 802.1Qbg implementation in lldpad we came
across a small problem in the handling of the netlink message
corresponding to PORT_PROFILE_RESPONSE_INPROGRESS. This should not
result in returning the default rc=1.
- src/util/macvtap.c: fix getPortProfileStatus() to return 0 in that
case and also fix an indentation problem
This would have detected the bug in commit 38ad33931 (Aug 09), which
we missed until commit f828ca35 (Jul 10); over 11 months later.
However, on Fedora 13, it also triggers LOTS of warnings from
the libcurl-devel header for two files:
esx/esx_vi.c: In function 'esxVI_CURL_Perform':
esx/esx_vi.c:232: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
esx/esx_vi.c:232: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
esx/esx_vi.c:232: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
...
xenapi/xenapi_driver.c: In function 'call_func':
xenapi/xenapi_driver.c:1872: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
xenapi/xenapi_driver.c:1872: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
xenapi/xenapi_driver.c:1872: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
...
libcurl allows to disable the type-checking code that triggers those
warnings, along with the reduction in type-safety of calls to some
libcurl functions. I figure this is worth the improved compiler
checking throughout the rest of libvirt.
* acinclude.m4 (--enable-compile-warnings=error): Add -Wlogical-op.
* configure.ac: Add -DCURL_DISABLE_TYPECHECK to LIBCURL_CFLAGS to
avoid compilation warning.
Suggested by Daniel P. Berrange.
Tweaked by Matthias Bolte.
LSB and https://fedoraproject.org/wiki/Packaging/SysVInitScript
require status to output something useful, rather than just use
the exit code.
* daemon/libvirt-guests.init.in (rh_status): Break into new routine,
and provide output.
(usage): Document status.
Reject extra arguments.
Return the correct status for unknown arguments, as mandated by
https://fedoraproject.org/wiki/Packaging/SysVInitScript
Add --help, as a permitted extension.
* daemon/libvirt-guests.init.in (usage): New function. Use it in
more places, and return correct value.
QEMU has had two different syntax for disk cache options
Old: on|off
New: writeback|writethrough|none
QEMU recently added another 'unsafe' option which broke the
libvirt check. We can avoid this & future breakage, if we
do a negative check for the old syntax, instead of a positive
check for the new syntax
* src/qemu/qemu_conf.c: Invert cache option check
Matthias Bolte