The target= setting in xl disk configuration can be used to encode
meta info that is meaningful to a backend. Leverage this fact to
support qdisk network disk types such as rbd. E.g. <disk> config
such as
<disk type='network' device='disk'>
<driver name='qemu' type='raw'/>
<source protocol='rbd' name='pool/image'>
<host name='mon1.example.org' port='6321'/>
<host name='mon2.example.org' port='6322'/>
<host name='mon3.example.org' port='6322'/>
</source>
<target dev='hdb' bus='ide'/>
<address type='drive' controller='0' bus='0' target='0' unit='1'/>
</disk>
can be converted to the following xl config (and vice versa)
disk = [ "format=raw,vdev=hdb,access=rw,backendtype=qdisk,
target=rbd:pool/image:auth_supported=none:mon_host=mon1.example.org\\:6321\\;mon2.example.org\\:6322\\;mon3.example.org\\:6322"
]
Note that in xl disk config, a literal backslash in target= must
be escaped with a backslash. Conversion of <auth> config is not
handled in this patch, but can be done in a follow-up patch.
Also add a test for the conversions.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
The most formal form of xl disk configuration uses key=value
syntax to define each configuration item, e.g.
format=raw, vdev=xvda, access=rw, backendtype=phy, target=disksrc
Change the xl disk formatter to produce this syntax, which allows
target= to contain meta info needed to setup a network-based
disksrc (e.g. rbd, nbd, iscsi). For details on xl disk config
format, see $xen-src/docs/misc/xl-disk-configuration.txt
Update the disk config in the tests to use the formal syntax.
But add tests to ensure disks specified with the positional
parameter syntax are correctly converted to <disk> XML.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
And use the newly added caps->host.netprefix (if it exists) for
interface names that match the autogenerated target names.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
... and consolidate the cmdline/extra/root parsing to facilitate doing
so.
The logic is the same as xl's parse_cmdline from the current xen.git master
branch (e6f0e099d2c17de47fd86e817b1998db903cab61).
On the formatting side switch to producing cmdline= instead of extra=.
Update a few tests and add serveral more.
- test-cmdline is added to test the exclusive use of cmdline.
- test-fullvirt-direct-kernel-boot.cfg is updated due to the switch
on the formatting side and now tests the exclusive use of cmdline=.
- Tests are added for both paravirt and fullvirt where the .cfg uses
extra= and (paravirt only) root=. These are format (xl->xml) only
since the inverse will generate cmdline= hence is not a round trip
(which was already true if using root=, which used to generate
extra= on the way back).
- Tests are added for both paravirt and fullvirt where the .cfg
declares cmdline= as well as bogus extra= and (paravirt only) root=
entries which should be ignored. Again these are format only tests
since the inverse won't include the bogus lines.
The last two bullets here required splitting the DO_TEST macro into
two halves, as is done in the xmconfigtest.c case.
In order to introduce a use of VIR_WARN for logging I had to add
virerror.h and VIR_LOG_INIT.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Both xm and xl config have long supported specifying vif rate
limiting, e.g.
vif = [ 'mac=00:16:3E:74:3d:76,bridge=br0,rate=10MB/s' ]
Add support for mapping rate to and from <bandwidth> in the xenconfig
parser and formatter. rate is mapped to the required 'average' attribute
of the <outbound> element, e.g.
<interface type='bridge'>
...
<bandwidth>
<outbound average='10240'/>
</bandwidth>
</interface>
Also add a unit test to check the conversion logic.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
From: Ian Campbell <ian.campbell@citrix.com>
xend prior to 4.0 understands vcpus as maxvcpus and vcpu_avail
as a bit map of which cpus are online (default is all).
xend from 4.0 onwards understands maxvcpus as maxvcpus and
vcpus as the number which are online (from 0..N-1). The
upstream commit (68a94cf528e6 "xm: Add maxvcpus support")
claims that if maxvcpus is omitted then the old behaviour
(i.e. obeying vcpu_avail) is retained, but AFAICT it was not,
in this case vcpu==maxcpus==online cpus. This is good for us
because handling anything else would be fiddly.
This patch changes parsing of the virDomainDef maxvcpus and vcpus
entries to use the corresponding 'maxvcpus' and 'vcpus' settings
from xm and xl config. It also drops use of the old Xen 3.x
'vcpu_avail' setting.
The change also removes the maxvcpus limit of MAX_VIRT_VCPUS (since
maxvcpus is simply a count, not a bit mask), which is particularly
crucial on ARM where MAX_VIRT_CPUS == 1 (since all guests are
expected to support vcpu placement, and therefore only the boot
vcpu's info lives in the shared info page).
Existing tests adjusted accordingly, and new tests added for the
'maxvcpus' setting.
Remove use of xendConfigVersion in the xm and xl config formatter/parsers
in src/xenconfig/. Adjust callers in the xen and libxl drivers accordingly.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Change all tests to use the latest XEND_CONFIG_VERSION
(XEND_CONFIG_VERSION_3_1_0 = 4). Fix tests that do not conform to
the latest version.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
This change ensures to call driver specific post-parse code to modify
domain definition after parsing hypervisor config the same way we do
after parsing XML.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
From xl.cfg950 man page:
spiceagent_mouse=BOOLEAN
Whether SPICE agent is used for client mouse mode. The default is
true (1) (turn on)
spicevdagent=BOOLEAN
Enables spice vdagent. The Spice vdagent is an optional component for
enhancing user experience and performing guest-oriented management
tasks. Its features includes: client mouse mode (no need to grab
mouse by client, no mouse lag), automatic adjustment of screen
resolution, copy and paste (text and image) between client and domU.
It also requires vdagent service installed on domU o.s. to work.
The default is 0.
spice_clipboard_sharing=BOOLEAN
Enables Spice clipboard sharing (copy/paste). It requires spicevdagent
enabled. The default is false (0).
So if spiceagent_mouse is enabled (client mouse mode) or
spice_clipboard_sharing is enabled, spicevdagent must be enabled.
Along with this change, s/spicedvagent/spicevdagent, set
spiceagent_mouse correctly, and add a test for these spice
features.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
This needs to specified in way too many places for a simple validation
check. The ostype/arch/virttype validation checks later in
DomainDefParseXML should catch most of the cases that this was covering.
Add support for HVM direct kernel boot in libxl. Also add a
test to verify domXML <-> native conversions.
Signed-off-by: Chunyan Liu <cyliu@suse.com>
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Commit cd5dc30 added this test, but it fails if
LIBXL_HAVE_BUILDINFO_USBDEVICE_LIST is not defined:
6) Xen XM-2-XML Format fullvirt-multiusb
... libvirt: error : unsupported configuration: multiple USB
devices not supported
FAILED
When libvirt is configured --without-xen, building the xlconfigtest
fails with
CCLD xlconfigtest
/usr/lib/gcc/x86_64-linux-gnu/4.7/../../../x86_64-linux-gnu/crt1.o
In function `_start': (.text+0x20): undefined reference to `main'
collect2: error: ld returned 1 exit status
Introduced in commit 4ed5fb91 by too much copy and paste from
xmconfigtest.
Add disk and spice config tests for the xen_xl config parser
Signed-off-by: Kiarie Kahurani <davidkiarie4@gmail.com>
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Jim Fehlig