linux/drivers/clk/at91/Makefile

#
# Makefile for at91 specific clk
#

obj-y += pmc.o sckc.o
obj-y += clk-slow.o clk-main.o clk-pll.o clk-plldiv.o clk-master.o
obj-y += clk-system.o clk-peripheral.o clk-programmable.o

obj-$(CONFIG_HAVE_AT91_AUDIO_PLL)	+= clk-audio-pll.o
obj-$(CONFIG_HAVE_AT91_UTMI)		+= clk-utmi.o
obj-$(CONFIG_HAVE_AT91_USB_CLK)		+= clk-usb.o
obj-$(CONFIG_HAVE_AT91_SMD)		+= clk-smd.o
obj-$(CONFIG_HAVE_AT91_H32MX)		+= clk-h32mx.o
obj-$(CONFIG_HAVE_AT91_GENERATED_CLK)	+= clk-generated.o
clk: at91: add PMC base support This patch adds at91 PMC (Power Management Controller) base support. All at91 clocks managed by the PMC unit will use this framework. This framework provides the following fonctionalities: - define a new struct at91_pmc to hide PMC internals (lock, PMC memory mapping, irq domain, ...) - read/write helper functions (pmc_read/write) to access PMC registers - lock/unlock helper functions (pmc_lock/unlock) to lock/unlock access to pmc registers - a new irq domain and its associated irq chip to request PMC specific interrupts (useful for clk prepare callbacks) The PMC unit is declared as a dt clk provider (CLK_OF_DECLARE), and every clk using this framework will declare a table of of_at91_clk_init_cb_t and add it to the pmc_clk_ids table. When the pmc dt clock setup function is called (by of_clk_init function), it triggers the registration of every supported child clk (those matching the definitions in pmc_clk_ids). This patch copies at91_pmc_base (memory mapping) and at91sam9_idle (function) from arch/arm/mach-at91/clock.c (which is not compiled if COMMON_CLK_AT91 is enabled). Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-12-02 22:07:02 +08:00			`#`
			`# Makefile for at91 specific clk`
			`#`

clk: at91: add slow clks driver AT91 slow clk is a clk multiplexer. In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can choose among 2 sources: an internal RC oscillator circuit and an oscillator using an external crystal. In other Socs (sam9260 family) the multiplexer source is hardcoded with the OSCSEL signal. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2014-05-08 00:02:15 +08:00			`obj-y += pmc.o sckc.o`
			`obj-y += clk-slow.o clk-main.o clk-pll.o clk-plldiv.o clk-master.o`
ARM: at91: remove AT91_PROGRAMMABLE_CLOCKS configuration option This AT91 specific Kconfig option removed the code that dealt with programmable clocks. Each AT91 SoC embeds programmable clocks and there is little gain to remove this code in case that such a clock is not used. If this option is not selected, it causes certain drivers to fail to build. We simply remove this option instead of adding code just to build a workaround. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> 2013-12-13 00:00:45 +08:00			`obj-y += clk-system.o clk-peripheral.o clk-programmable.o`
clk: at91: add PMC programmable clocks This patch adds new at91 programmable clocks implementation using common clk framework. A programmable clock is a clock which can be exported on a given pin to clock external devices. Each programmable clock is given an id (from 0 to 8). The number of available programmable clocks depends on the SoC you're using. Programmable clock driver only implements the clock setting (clock rate and parent setting). It must be chained to a system clock in order to enable/disable the generated clock. The PCKX pins used to output the clock signals must be assigned to the appropriate peripheral (see atmel's datasheets). Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-11 17:57:04 +08:00
clk: at91: add audio pll clock drivers This new clock driver set allows to have a fractional divided clock that would generate a precise clock particularly suitable for audio applications. The main audio pll clock has two children clocks: one that is connected to the PMC, the other that can directly drive a pad. As these two routes have different enable bits and different dividers and divider formulas, they are handled by two different drivers. Each of them could modify the rate of the main audio pll parent. The main audio pll clock can output 620MHz to 700MHz. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> 2017-08-10 14:34:03 +08:00			`obj-$(CONFIG_HAVE_AT91_AUDIO_PLL) += clk-audio-pll.o`
clk: at91: add PMC utmi clock This adds new at91 utmi clock implementation using common clk framework. This clock is a pll with a fixed factor (x40). It is used as a source for usb clock. Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-11 18:22:06 +08:00			`obj-$(CONFIG_HAVE_AT91_UTMI) += clk-utmi.o`
clk: at91: add PMC usb clock This patch adds new at91 usb clock implementation using common clk framework. This clock is used to clock usb ports (ohci, ehci and udc). Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-18 00:55:41 +08:00			`obj-$(CONFIG_HAVE_AT91_USB_CLK) += clk-usb.o`
clk: at91: add PMC smd clock This patch adds at91 smd (Soft Modem) clock implementation using common clk framework. Not used by any driver right now. Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-11 19:27:06 +08:00			`obj-$(CONFIG_HAVE_AT91_SMD) += clk-smd.o`
clk: at91: add a driver for the h32mx clock Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix interconnect (h32mx) has a clock that can be setup at the half of the h64mx clock (which is mck). The h32mx clock can not exceed 90 MHz. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2014-09-16 00:15:53 +08:00			`obj-$(CONFIG_HAVE_AT91_H32MX) += clk-h32mx.o`
clk: at91: add generated clock driver Add a new type of clocks that can be provided to a peripheral. In addition to the peripheral clock, this new clock that can use several input clocks as parents can generate divided rates. This would allow a peripheral to have finer grained clocks for generating a baud rate, clocking an asynchronous part or having more options in frequency. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> [sboyd@codeaurora.org: Transition to new clk_hw provider APIs] Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> 2015-07-31 17:43:12 +08:00			`obj-$(CONFIG_HAVE_AT91_GENERATED_CLK) += clk-generated.o`