linux/drivers/net/wireless/ath/ath9k/ani.h

166 lines
4.4 KiB
C
Raw Normal View History

/*
* Copyright (c) 2008-2009 Atheros Communications Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
#ifndef ANI_H
#define ANI_H
#define HAL_PROCESS_ANI 0x00000001
#define DO_ANI(ah) (((ah)->proc_phyerr & HAL_PROCESS_ANI) && ah->curchan)
#define BEACON_RSSI(ahp) (ahp->stats.avgbrssi)
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
/* units are errors per second */
#define ATH9K_ANI_OFDM_TRIG_HIGH_OLD 500
#define ATH9K_ANI_OFDM_TRIG_HIGH_NEW 1000
/* units are errors per second */
#define ATH9K_ANI_OFDM_TRIG_LOW_OLD 200
#define ATH9K_ANI_OFDM_TRIG_LOW_NEW 400
/* units are errors per second */
#define ATH9K_ANI_CCK_TRIG_HIGH_OLD 200
#define ATH9K_ANI_CCK_TRIG_HIGH_NEW 600
/* units are errors per second */
#define ATH9K_ANI_CCK_TRIG_LOW_OLD 100
#define ATH9K_ANI_CCK_TRIG_LOW_NEW 300
#define ATH9K_ANI_NOISE_IMMUNE_LVL 4
#define ATH9K_ANI_USE_OFDM_WEAK_SIG true
#define ATH9K_ANI_CCK_WEAK_SIG_THR false
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
#define ATH9K_ANI_SPUR_IMMUNE_LVL_OLD 7
#define ATH9K_ANI_SPUR_IMMUNE_LVL_NEW 3
#define ATH9K_ANI_FIRSTEP_LVL_OLD 0
#define ATH9K_ANI_FIRSTEP_LVL_NEW 2
#define ATH9K_ANI_RSSI_THR_HIGH 40
#define ATH9K_ANI_RSSI_THR_LOW 7
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
#define ATH9K_ANI_PERIOD_OLD 100
#define ATH9K_ANI_PERIOD_NEW 1000
/* in ms */
#define ATH9K_ANI_POLLINTERVAL_OLD 100
#define ATH9K_ANI_POLLINTERVAL_NEW 1000
#define HAL_NOISE_IMMUNE_MAX 4
#define HAL_SPUR_IMMUNE_MAX 7
#define HAL_FIRST_STEP_MAX 2
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
#define ATH9K_SIG_FIRSTEP_SETTING_MIN 0
#define ATH9K_SIG_FIRSTEP_SETTING_MAX 20
#define ATH9K_SIG_SPUR_IMM_SETTING_MIN 0
#define ATH9K_SIG_SPUR_IMM_SETTING_MAX 22
#define ATH9K_ANI_ENABLE_MRC_CCK true
/* values here are relative to the INI */
enum ath9k_ani_cmd {
ATH9K_ANI_PRESENT = 0x1,
ATH9K_ANI_NOISE_IMMUNITY_LEVEL = 0x2,
ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION = 0x4,
ATH9K_ANI_CCK_WEAK_SIGNAL_THR = 0x8,
ATH9K_ANI_FIRSTEP_LEVEL = 0x10,
ATH9K_ANI_SPUR_IMMUNITY_LEVEL = 0x20,
ATH9K_ANI_MODE = 0x40,
ATH9K_ANI_PHYERR_RESET = 0x80,
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
ATH9K_ANI_MRC_CCK = 0x100,
ATH9K_ANI_ALL = 0xfff
};
struct ath9k_mib_stats {
u32 ackrcv_bad;
u32 rts_bad;
u32 rts_good;
u32 fcs_bad;
u32 beacons;
};
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
/* INI default values for ANI registers */
struct ath9k_ani_default {
u16 m1ThreshLow;
u16 m2ThreshLow;
u16 m1Thresh;
u16 m2Thresh;
u16 m2CountThr;
u16 m2CountThrLow;
u16 m1ThreshLowExt;
u16 m2ThreshLowExt;
u16 m1ThreshExt;
u16 m2ThreshExt;
u16 firstep;
u16 firstepLow;
u16 cycpwrThr1;
u16 cycpwrThr1Ext;
};
struct ar5416AniState {
struct ath9k_channel *c;
u8 noiseImmunityLevel;
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
u8 ofdmNoiseImmunityLevel;
u8 cckNoiseImmunityLevel;
bool ofdmsTurn;
u8 mrcCCKOff;
u8 spurImmunityLevel;
u8 firstepLevel;
u8 ofdmWeakSigDetectOff;
u8 cckWeakSigThreshold;
u32 listenTime;
int32_t rssiThrLow;
int32_t rssiThrHigh;
u32 noiseFloor;
u32 ofdmPhyErrCount;
u32 cckPhyErrCount;
int16_t pktRssi[2];
int16_t ofdmErrRssi[2];
int16_t cckErrRssi[2];
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
struct ath9k_ani_default iniDef;
};
struct ar5416Stats {
u32 ast_ani_niup;
u32 ast_ani_nidown;
u32 ast_ani_spurup;
u32 ast_ani_spurdown;
u32 ast_ani_ofdmon;
u32 ast_ani_ofdmoff;
u32 ast_ani_cckhigh;
u32 ast_ani_ccklow;
u32 ast_ani_stepup;
u32 ast_ani_stepdown;
u32 ast_ani_ofdmerrs;
u32 ast_ani_cckerrs;
u32 ast_ani_reset;
u32 ast_ani_lzero;
u32 ast_ani_lneg;
u32 avgbrssi;
struct ath9k_mib_stats ast_mibstats;
};
#define ah_mibStats stats.ast_mibstats
void ath9k_enable_mib_counters(struct ath_hw *ah);
void ath9k_hw_disable_mib_counters(struct ath_hw *ah);
void ath9k_hw_ani_setup(struct ath_hw *ah);
void ath9k_hw_ani_init(struct ath_hw *ah);
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
int ath9k_hw_get_ani_channel_idx(struct ath_hw *ah,
struct ath9k_channel *chan);
#endif /* ANI_H */