linux/drivers/misc/Makefile

75 lines
2.7 KiB
Makefile
Raw Normal View History

#
# Makefile for misc devices that really don't fit anywhere else.
#
obj-$(CONFIG_IBM_ASM) += ibmasm/
obj-$(CONFIG_AD525X_DPOT) += ad525x_dpot.o
obj-$(CONFIG_AD525X_DPOT_I2C) += ad525x_dpot-i2c.o
obj-$(CONFIG_AD525X_DPOT_SPI) += ad525x_dpot-spi.o
obj-$(CONFIG_INTEL_MID_PTI) += pti.o
obj-$(CONFIG_ATMEL_SSC) += atmel-ssc.o
obj-$(CONFIG_ATMEL_TCLIB) += atmel_tclib.o
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 08:20:28 +08:00
obj-$(CONFIG_BMP085) += bmp085.o
obj-$(CONFIG_BMP085_I2C) += bmp085-i2c.o
obj-$(CONFIG_BMP085_SPI) += bmp085-spi.o
obj-$(CONFIG_DUMMY_IRQ) += dummy-irq.o
obj-$(CONFIG_ICS932S401) += ics932s401.o
obj-$(CONFIG_LKDTM) += lkdtm.o
obj-$(CONFIG_TIFM_CORE) += tifm_core.o
obj-$(CONFIG_TIFM_7XX1) += tifm_7xx1.o
obj-$(CONFIG_PHANTOM) += phantom.o
obj-$(CONFIG_QCOM_COINCELL) += qcom-coincell.o
obj-$(CONFIG_SENSORS_BH1780) += bh1780gli.o
obj-$(CONFIG_SENSORS_BH1770) += bh1770glc.o
obj-$(CONFIG_SENSORS_APDS990X) += apds990x.o
obj-$(CONFIG_SGI_IOC4) += ioc4.o
obj-$(CONFIG_ENCLOSURE_SERVICES) += enclosure.o
kgdb: add kgdb internal test suite This patch adds regression tests for testing the kgdb core and arch specific implementation. The kgdb test suite is designed to be built into the kernel and not as a module because it uses a number of low level kernel and kgdb primitives which should not be exported externally. The kgdb test suite is designed as a KGDB I/O module which simulates the communications that a debugger would have with kgdb. The tests are broken up in to a line by line and referenced here as a "get" which is kgdb requesting input and "put" which is kgdb sending a response. The kgdb suite can be invoked from the kernel command line arguments system or executed dynamically at run time. The test suite uses the variable "kgdbts" to obtain the information about which tests to run and to configure the verbosity level. The following are the various characters you can use with the kgdbts= line: When using the "kgdbts=" you only choose one of the following core test types: A = Run all the core tests silently V1 = Run all the core tests with minimal output V2 = Run all the core tests in debug mode You can also specify optional tests: N## = Go to sleep with interrupts of for ## seconds to test the HW NMI watchdog F## = Break at do_fork for ## iterations S## = Break at sys_open for ## iterations NOTE: that the do_fork and sys_open tests are mutually exclusive. To invoke the kgdb test suite from boot you use a kernel start argument as follows: kgdbts=V1 kgdbwait Or if you wanted to perform the NMI test for 6 seconds and do_fork test for 100 forks, you could use: kgdbts=V1N6F100 kgdbwait The test suite can also be invoked at run time with: echo kgdbts=V1N6F100 > /sys/module/kgdbts/parameters/kgdbts Or as another example: echo kgdbts=V2 > /sys/module/kgdbts/parameters/kgdbts When developing a new kgdb arch specific implementation or using these tests for the purpose of regression testing, several invocations are required. 1) Boot with the test suite enabled by using the kernel arguments "kgdbts=V1F100 kgdbwait" ## If kgdb arch specific implementation has NMI use "kgdbts=V1N6F100 2) After the system boot run the basic test. echo kgdbts=V1 > /sys/module/kgdbts/parameters/kgdbts 3) Run the concurrency tests. It is best to use n+1 while loops where n is the number of cpus you have in your system. The example below uses only two loops. ## This tests break points on sys_open while [ 1 ] ; do find / > /dev/null 2>&1 ; done & while [ 1 ] ; do find / > /dev/null 2>&1 ; done & echo kgdbts=V1S10000 > /sys/module/kgdbts/parameters/kgdbts fg # and hit control-c fg # and hit control-c ## This tests break points on do_fork while [ 1 ] ; do date > /dev/null ; done & while [ 1 ] ; do date > /dev/null ; done & echo kgdbts=V1F1000 > /sys/module/kgdbts/parameters/kgdbts fg # and hit control-c Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-03-08 06:34:17 +08:00
obj-$(CONFIG_KGDB_TESTS) += kgdbts.o
obj-$(CONFIG_SGI_XP) += sgi-xp/
obj-$(CONFIG_SGI_GRU) += sgi-gru/
obj-$(CONFIG_CS5535_MFGPT) += cs5535-mfgpt.o
obj-$(CONFIG_HP_ILO) += hpilo.o
obj-$(CONFIG_APDS9802ALS) += apds9802als.o
obj-$(CONFIG_ISL29003) += isl29003.o
obj-$(CONFIG_ISL29020) += isl29020.o
obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o
obj-$(CONFIG_DS1682) += ds1682.o
obj-$(CONFIG_TI_DAC7512) += ti_dac7512.o
obj-$(CONFIG_C2PORT) += c2port/
obj-$(CONFIG_HMC6352) += hmc6352.o
obj-y += eeprom/
obj-y += cb710/
obj-$(CONFIG_SPEAR13XX_PCIE_GADGET) += spear13xx_pcie_gadget.o
obj-$(CONFIG_VMWARE_BALLOON) += vmw_balloon.o
obj-$(CONFIG_ARM_CHARLCD) += arm-charlcd.o
obj-$(CONFIG_PCH_PHUB) += pch_phub.o
obj-y += ti-st/
obj-y += lis3lv02d/
obj-$(CONFIG_USB_SWITCH_FSA9480) += fsa9480.o
obj-$(CONFIG_ALTERA_STAPL) +=altera-stapl/
obj-$(CONFIG_INTEL_MEI) += mei/
obj-$(CONFIG_VMWARE_VMCI) += vmw_vmci/
obj-$(CONFIG_LATTICE_ECP3_CONFIG) += lattice-ecp3-config.o
obj-$(CONFIG_SRAM) += sram.o
obj-y += mic/
obj-$(CONFIG_GENWQE) += genwqe/
obj-$(CONFIG_ECHO) += echo/
obj-$(CONFIG_VEXPRESS_SYSCFG) += vexpress-syscfg.o
obj-$(CONFIG_CXL_BASE) += cxl/
obj-$(CONFIG_PANEL) += panel.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_core.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_bugs.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_heap.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_perms.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_rodata_objcopy.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_usercopy.o
OBJCOPYFLAGS :=
OBJCOPYFLAGS_lkdtm_rodata_objcopy.o := \
--set-section-flags .text=alloc,readonly \
--rename-section .text=.rodata
targets += lkdtm_rodata.o lkdtm_rodata_objcopy.o
$(obj)/lkdtm_rodata_objcopy.o: $(obj)/lkdtm_rodata.o FORCE
$(call if_changed,objcopy)