linux/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt

Freescale i.MX7 Mipi CSI2
=========================

mipi_csi2 node
--------------

This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is
compatible with previous version of Samsung D-phy.

Required properties:

- compatible    : "fsl,imx7-mipi-csi2";
- reg           : base address and length of the register set for the device;
- interrupts    : should contain MIPI CSIS interrupt;
- clocks        : list of clock specifiers, see
        Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
- clock-names   : must contain "pclk", "wrap" and "phy" entries, matching
                  entries in the clock property;
- power-domains : a phandle to the power domain, see
          Documentation/devicetree/bindings/power/power_domain.txt for details.
- reset-names   : should include following entry "mrst";
- resets        : a list of phandle, should contain reset entry of
                  reset-names;
- phy-supply    : from the generic phy bindings, a phandle to a regulator that
	          provides power to MIPI CSIS core;

Optional properties:

- clock-frequency : The IP's main (system bus) clock frequency in Hz, default
		    value when this property is not specified is 166 MHz;
- fsl,csis-hs-settle : differential receiver (HS-RX) settle time;

The device node should contain two 'port' child nodes with one child 'endpoint'
node, according to the bindings defined in:
 Documentation/devicetree/bindings/ media/video-interfaces.txt.
 The following are properties specific to those nodes.

port node
---------

- reg		  : (required) can take the values 0 or 1, where 0 shall be
                     related to the sink port and port 1 shall be the source
                     one;

endpoint node
-------------

- data-lanes    : (required) an array specifying active physical MIPI-CSI2
		    data input lanes and their mapping to logical lanes; this
                    shall only be applied to port 0 (sink port), the array's
                    content is unused only its length is meaningful,
                    in this case the maximum length supported is 2;

example:

        mipi_csi: mipi-csi@30750000 {
                #address-cells = <1>;
                #size-cells = <0>;

                compatible = "fsl,imx7-mipi-csi2";
                reg = <0x30750000 0x10000>;
                interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
                clocks = <&clks IMX7D_IPG_ROOT_CLK>,
                                <&clks IMX7D_MIPI_CSI_ROOT_CLK>,
                                <&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
                clock-names = "pclk", "wrap", "phy";
                clock-frequency = <166000000>;
                power-domains = <&pgc_mipi_phy>;
                phy-supply = <&reg_1p0d>;
                resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
                reset-names = "mrst";
                fsl,csis-hs-settle = <3>;

                port@0 {
                        reg = <0>;

                        mipi_from_sensor: endpoint {
                                remote-endpoint = <&ov2680_to_mipi>;
                                data-lanes = <1>;
                        };
                };

                port@1 {
                        reg = <1>;

                        mipi_vc0_to_csi_mux: endpoint {
                                remote-endpoint = <&csi_mux_from_mipi_vc0>;
                        };
                };
        };