linux/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c

149 lines
4.1 KiB
C
Raw Normal View History

ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk The r8a7790/lager and r8a7791/koelsch development boards have da9063 and da9210 regulators. Both regulators have their interrupt request lines tied to the same interrupt pin (IRQ2) on the SoC. After cold boot or da9063-induced restart, both the da9063 and da9210 seem to assert their interrupt request lines. Hence as soon as one driver requests this irq, it gets stuck in an interrupt storm, as it only manages to deassert its own interrupt request line, and the other driver hasn't installed an interrupt handler yet. To handle this, install a quirk that masks the interrupts in both the da9063 and da9210. This quirk has to run after the i2c master driver has been initialized, but before the i2c slave drivers are initialized. As it depends on i2c, select I2C if one of the affected platforms is enabled in the kernel config. On koelsch, the following happens: - Cold boot or reboot using the da9063 restart handler: IRQ2 is asserted, installing da9063/da9210 regulator quirk ... i2c i2c-6: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb i2c 6-0058: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb i2c 6-0058: Detected da9063 i2c 6-0058: Masking da9063 interrupt sources i2c 6-0068: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb i2c 6-0068: Detected da9210 i2c 6-0068: Masking da9210 interrupt sources i2c 6-0068: IRQ2 is not asserted, removing quirk - Warm boot (reset button): rcar_gen2_regulator_quirk: IRQ2 is not asserted, not installing quirk Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2015-03-10 03:50:40 +08:00
/*
* R-Car Generation 2 da9063/da9210 regulator quirk
*
* The r8a7790/lager and r8a7791/koelsch development boards have da9063 and
* da9210 regulators. Both regulators have their interrupt request lines tied
* to the same interrupt pin (IRQ2) on the SoC.
*
* After cold boot or da9063-induced restart, both the da9063 and da9210 seem
* to assert their interrupt request lines. Hence as soon as one driver
* requests this irq, it gets stuck in an interrupt storm, as it only manages
* to deassert its own interrupt request line, and the other driver hasn't
* installed an interrupt handler yet.
*
* To handle this, install a quirk that masks the interrupts in both the
* da9063 and da9210. This quirk has to run after the i2c master driver has
* been initialized, but before the i2c slave drivers are initialized.
*
* Copyright (C) 2015 Glider bvba
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/device.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/notifier.h>
#include <linux/of.h>
#include <linux/mfd/da9063/registers.h>
#define IRQC_BASE 0xe61c0000
#define IRQC_MONITOR 0x104 /* IRQn Signal Level Monitor Register */
#define REGULATOR_IRQ_MASK BIT(2) /* IRQ2, active low */
static void __iomem *irqc;
static const u8 da9063_mask_regs[] = {
DA9063_REG_IRQ_MASK_A,
DA9063_REG_IRQ_MASK_B,
DA9063_REG_IRQ_MASK_C,
DA9063_REG_IRQ_MASK_D,
};
/* DA9210 System Control and Event Registers */
#define DA9210_REG_MASK_A 0x54
#define DA9210_REG_MASK_B 0x55
static const u8 da9210_mask_regs[] = {
DA9210_REG_MASK_A,
DA9210_REG_MASK_B,
};
static void da9xxx_mask_irqs(struct i2c_client *client, const u8 regs[],
unsigned int nregs)
{
unsigned int i;
dev_info(&client->dev, "Masking %s interrupt sources\n", client->name);
for (i = 0; i < nregs; i++) {
int error = i2c_smbus_write_byte_data(client, regs[i], ~0);
if (error) {
dev_err(&client->dev, "i2c error %d\n", error);
return;
}
}
}
static int regulator_quirk_notify(struct notifier_block *nb,
unsigned long action, void *data)
{
struct device *dev = data;
struct i2c_client *client;
u32 mon;
mon = ioread32(irqc + IRQC_MONITOR);
dev_dbg(dev, "%s: %ld, IRQC_MONITOR = 0x%x\n", __func__, action, mon);
if (mon & REGULATOR_IRQ_MASK)
goto remove;
if (action != BUS_NOTIFY_ADD_DEVICE || dev->type == &i2c_adapter_type)
return 0;
client = to_i2c_client(dev);
dev_dbg(dev, "Detected %s\n", client->name);
if ((client->addr == 0x58 && !strcmp(client->name, "da9063")))
da9xxx_mask_irqs(client, da9063_mask_regs,
ARRAY_SIZE(da9063_mask_regs));
else if (client->addr == 0x68 && !strcmp(client->name, "da9210"))
da9xxx_mask_irqs(client, da9210_mask_regs,
ARRAY_SIZE(da9210_mask_regs));
mon = ioread32(irqc + IRQC_MONITOR);
if (mon & REGULATOR_IRQ_MASK)
goto remove;
return 0;
remove:
dev_info(dev, "IRQ2 is not asserted, removing quirk\n");
bus_unregister_notifier(&i2c_bus_type, nb);
iounmap(irqc);
return 0;
}
static struct notifier_block regulator_quirk_nb = {
.notifier_call = regulator_quirk_notify
};
static int __init rcar_gen2_regulator_quirk(void)
{
u32 mon;
if (!of_machine_is_compatible("renesas,koelsch") &&
!of_machine_is_compatible("renesas,lager") &&
!of_machine_is_compatible("renesas,gose"))
ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk The r8a7790/lager and r8a7791/koelsch development boards have da9063 and da9210 regulators. Both regulators have their interrupt request lines tied to the same interrupt pin (IRQ2) on the SoC. After cold boot or da9063-induced restart, both the da9063 and da9210 seem to assert their interrupt request lines. Hence as soon as one driver requests this irq, it gets stuck in an interrupt storm, as it only manages to deassert its own interrupt request line, and the other driver hasn't installed an interrupt handler yet. To handle this, install a quirk that masks the interrupts in both the da9063 and da9210. This quirk has to run after the i2c master driver has been initialized, but before the i2c slave drivers are initialized. As it depends on i2c, select I2C if one of the affected platforms is enabled in the kernel config. On koelsch, the following happens: - Cold boot or reboot using the da9063 restart handler: IRQ2 is asserted, installing da9063/da9210 regulator quirk ... i2c i2c-6: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb i2c 6-0058: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb i2c 6-0058: Detected da9063 i2c 6-0058: Masking da9063 interrupt sources i2c 6-0068: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb i2c 6-0068: Detected da9210 i2c 6-0068: Masking da9210 interrupt sources i2c 6-0068: IRQ2 is not asserted, removing quirk - Warm boot (reset button): rcar_gen2_regulator_quirk: IRQ2 is not asserted, not installing quirk Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2015-03-10 03:50:40 +08:00
return -ENODEV;
irqc = ioremap(IRQC_BASE, PAGE_SIZE);
if (!irqc)
return -ENOMEM;
mon = ioread32(irqc + IRQC_MONITOR);
if (mon & REGULATOR_IRQ_MASK) {
pr_debug("%s: IRQ2 is not asserted, not installing quirk\n",
__func__);
iounmap(irqc);
return 0;
}
pr_info("IRQ2 is asserted, installing da9063/da9210 regulator quirk\n");
bus_register_notifier(&i2c_bus_type, &regulator_quirk_nb);
return 0;
}
arch_initcall(rcar_gen2_regulator_quirk);