openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
linux/arch/arm/boot/dts/tegra124-nyan.dtsi

696 lines
16 KiB
Plaintext
Raw Normal View History

ARM: tegra: Move generic parts out of the nyan-big DT In preparation for adding the DT for the nyan-blaze board. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:17 +08:00
#include <dt-bindings/input/input.h>
#include "tegra124.dtsi"
/ {
aliases {
rtc0 = "/i2c@0,7000d000/pmic@40";
rtc1 = "/rtc@0,7000e000";
serial0 = &uarta;
};
memory {
reg = <0x0 0x80000000 0x0 0x80000000>;
};
host1x@0,50000000 {
hdmi@0,54280000 {
status = "okay";
vdd-supply = <&vdd_3v3_hdmi>;
pll-supply = <&vdd_hdmi_pll>;
hdmi-supply = <&vdd_5v0_hdmi>;
nvidia,ddc-i2c-bus = <&hdmi_ddc>;
nvidia,hpd-gpio =
<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
};
sor@0,54540000 {
status = "okay";
nvidia,dpaux = <&dpaux>;
nvidia,panel = <&panel>;
};
dpaux@0,545c0000 {
vdd-supply = <&vdd_3v3_panel>;
status = "okay";
};
};
serial@0,70006000 {
/* Debug connector on the bottom of the board near SD card. */
status = "okay";
};
pwm@0,7000a000 {
status = "okay";
};
i2c@0,7000c000 {
status = "okay";
clock-frequency = <100000>;
acodec: audio-codec@10 {
compatible = "maxim,max98090";
reg = <0x10>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
};
temperature-sensor@4c {
compatible = "ti,tmp451";
reg = <0x4c>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
};
};
i2c@0,7000c400 {
status = "okay";
clock-frequency = <100000>;
ARM: tegra: Add node for trackpad in Nyan boards The Nyan boards have a eKTH3000 from Elan as their trackpad, connected through I2C. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:20 +08:00
trackpad@15 {
compatible = "elan,ekth3000";
reg = <0x15>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
wakeup-source;
};
ARM: tegra: Move generic parts out of the nyan-big DT In preparation for adding the DT for the nyan-blaze board. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:17 +08:00
};
i2c@0,7000c500 {
status = "okay";
clock-frequency = <400000>;
tpm@20 {
compatible = "infineon,slb9645tt";
reg = <0x20>;
};
};
hdmi_ddc: i2c@0,7000c700 {
status = "okay";
clock-frequency = <100000>;
};
i2c@0,7000d000 {
status = "okay";
clock-frequency = <400000>;
pmic: pmic@40 {
compatible = "ams,as3722";
reg = <0x40>;
interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
ams,system-power-controller;
#interrupt-cells = <2>;
interrupt-controller;
gpio-controller;
#gpio-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&as3722_default>;
as3722_default: pinmux {
gpio0 {
pins = "gpio0";
function = "gpio";
bias-pull-down;
};
gpio1 {
pins = "gpio1";
function = "gpio";
bias-pull-up;
};
gpio2_4_7 {
pins = "gpio2", "gpio4", "gpio7";
function = "gpio";
bias-pull-up;
};
gpio3_6 {
pins = "gpio3", "gpio6";
bias-high-impedance;
};
gpio5 {
pins = "gpio5";
function = "clk32k-out";
bias-pull-down;
};
};
regulators {
vsup-sd2-supply = <&vdd_5v0_sys>;
vsup-sd3-supply = <&vdd_5v0_sys>;
vsup-sd4-supply = <&vdd_5v0_sys>;
vsup-sd5-supply = <&vdd_5v0_sys>;
vin-ldo0-supply = <&vdd_1v35_lp0>;
vin-ldo1-6-supply = <&vdd_3v3_run>;
vin-ldo2-5-7-supply = <&vddio_1v8>;
vin-ldo3-4-supply = <&vdd_3v3_sys>;
vin-ldo9-10-supply = <&vdd_5v0_sys>;
vin-ldo11-supply = <&vdd_3v3_run>;
sd0 {
regulator-name = "+VDD_CPU_AP";
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1350000>;
regulator-min-microamp = <3500000>;
regulator-max-microamp = <3500000>;
regulator-always-on;
regulator-boot-on;
ams,ext-control = <2>;
};
sd1 {
regulator-name = "+VDD_CORE";
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1350000>;
regulator-min-microamp = <2500000>;
regulator-max-microamp = <4000000>;
regulator-always-on;
regulator-boot-on;
ams,ext-control = <1>;
};
vdd_1v35_lp0: sd2 {
regulator-name = "+1.35V_LP0(sd2)";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
};
sd3 {
regulator-name = "+1.35V_LP0(sd3)";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
};
vdd_1v05_run: sd4 {
regulator-name = "+1.05V_RUN";
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
};
vddio_1v8: sd5 {
regulator-name = "+1.8V_VDDIO";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
sd6 {
regulator-name = "+VDD_GPU_AP";
regulator-min-microvolt = <650000>;
regulator-max-microvolt = <1200000>;
regulator-min-microamp = <3500000>;
regulator-max-microamp = <3500000>;
regulator-boot-on;
regulator-always-on;
};
ldo0 {
regulator-name = "+1.05V_RUN_AVDD";
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
regulator-boot-on;
regulator-always-on;
ams,ext-control = <1>;
};
ldo1 {
regulator-name = "+1.8V_RUN_CAM";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
ldo2 {
regulator-name = "+1.2V_GEN_AVDD";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-boot-on;
regulator-always-on;
};
ldo3 {
regulator-name = "+1.00V_LP0_VDD_RTC";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
ams,enable-tracking;
};
vdd_run_cam: ldo4 {
regulator-name = "+3.3V_RUN_CAM";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
ldo5 {
regulator-name = "+1.2V_RUN_CAM_FRONT";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
vddio_sdmmc3: ldo6 {
regulator-name = "+VDDIO_SDMMC3";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
ldo7 {
regulator-name = "+1.05V_RUN_CAM_REAR";
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
};
ldo9 {
regulator-name = "+2.8V_RUN_TOUCH";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
ldo10 {
regulator-name = "+2.8V_RUN_CAM_AF";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
ldo11 {
regulator-name = "+1.8V_RUN_VPP_FUSE";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
};
};
spi@0,7000d400 {
status = "okay";
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
spi-max-frequency = <3000000>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
reg = <0>;
google,cros-ec-spi-msg-delay = <2000>;
i2c-tunnel {
compatible = "google,cros-ec-i2c-tunnel";
#address-cells = <1>;
#size-cells = <0>;
google,remote-bus = <0>;
charger: bq24735@9 {
compatible = "ti,bq24735";
reg = <0x9>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(J, 0)
GPIO_ACTIVE_HIGH>;
ti,ac-detect-gpios = <&gpio
TEGRA_GPIO(J, 0)
GPIO_ACTIVE_HIGH>;
};
battery: sbs-battery@b {
compatible = "sbs,sbs-battery";
reg = <0xb>;
sbs,i2c-retry-count = <2>;
sbs,poll-retry-count = <10>;
power-supplies = <&charger>;
};
};
};
};
spi@0,7000da00 {
status = "okay";
spi-max-frequency = <25000000>;
flash@0 {
compatible = "winbond,w25q32dw";
ARM: tegra: nyan: Set maximum frequency for SPI flash Otherwise the SPI core will refuse to register the device. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:23 +08:00
spi-max-frequency = <25000000>;
ARM: tegra: Move generic parts out of the nyan-big DT In preparation for adding the DT for the nyan-blaze board. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:17 +08:00
reg = <0>;
};
};
pmc@0,7000e400 {
nvidia,invert-interrupt;
nvidia,suspend-mode = <0>;
nvidia,cpu-pwr-good-time = <500>;
nvidia,cpu-pwr-off-time = <300>;
nvidia,core-pwr-good-time = <641 3845>;
nvidia,core-pwr-off-time = <61036>;
nvidia,core-power-req-active-high;
nvidia,sys-clock-req-active-high;
};
hda@0,70030000 {
status = "okay";
};
ARM: tegra: Use pwrseq-simple for the wifi in Nyan The Nyan boards have a Marvell 88w8897 wifi card connected through SDIO that needs the reset line to be asserted before mmc power up and deasserted afterwards. This patch also adds references to the power supplies of the card so that the regulators are enabled when it's probed. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:21 +08:00
sdhci0_pwrseq: sdhci0_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
};
ARM: tegra: Move generic parts out of the nyan-big DT In preparation for adding the DT for the nyan-blaze board. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:17 +08:00
sdhci@0,700b0000 { /* WiFi/BT on this bus */
status = "okay";
bus-width = <4>;
no-1-8-v;
non-removable;
ARM: tegra: Use pwrseq-simple for the wifi in Nyan The Nyan boards have a Marvell 88w8897 wifi card connected through SDIO that needs the reset line to be asserted before mmc power up and deasserted afterwards. This patch also adds references to the power supplies of the card so that the regulators are enabled when it's probed. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:21 +08:00
mmc-pwrseq = <&sdhci0_pwrseq>;
vmmc-supply = <&vdd_3v3_lp0>;
vqmmc-supply = <&vddio_1v8>;
ARM: tegra: nyan: The WiFi card is kept powered during suspend Even if the host controller doesn't have power during suspend, the card is kept powered. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:27 +08:00
keep-power-in-suspend;
ARM: tegra: Move generic parts out of the nyan-big DT In preparation for adding the DT for the nyan-blaze board. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:17 +08:00
};
sdhci@0,700b0400 { /* SD Card on this bus */
status = "okay";
cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
bus-width = <4>;
no-1-8-v;
vqmmc-supply = <&vddio_sdmmc3>;
};
sdhci@0,700b0600 { /* eMMC on this bus */
status = "okay";
bus-width = <8>;
no-1-8-v;
non-removable;
};
ahub@0,70300000 {
i2s@0,70301100 {
status = "okay";
};
};
usb@0,7d000000 { /* Rear external USB port. */
status = "okay";
};
usb-phy@0,7d000000 {
status = "okay";
vbus-supply = <&vdd_usb1_vbus>;
};
usb@0,7d004000 { /* Internal webcam. */
status = "okay";
};
usb-phy@0,7d004000 {
status = "okay";
vbus-supply = <&vdd_run_cam>;
};
usb@0,7d008000 { /* Left external USB port. */
status = "okay";
};
usb-phy@0,7d008000 {
status = "okay";
vbus-supply = <&vdd_usb3_vbus>;
};
backlight: backlight {
compatible = "pwm-backlight";
enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
power-supply = <&vdd_led>;
pwms = <&pwm 1 1000000>;
default-brightness-level = <224>;
brightness-levels =
< 0 1 2 3 4 5 6 7
8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23
24 25 26 27 28 29 30 31
32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47
48 49 50 51 52 53 54 55
56 57 58 59 60 61 62 63
64 65 66 67 68 69 70 71
72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87
88 89 90 91 92 93 94 95
96 97 98 99 100 101 102 103
104 105 106 107 108 109 110 111
112 113 114 115 116 117 118 119
120 121 122 123 124 125 126 127
128 129 130 131 132 133 134 135
136 137 138 139 140 141 142 143
144 145 146 147 148 149 150 151
152 153 154 155 156 157 158 159
160 161 162 163 164 165 166 167
168 169 170 171 172 173 174 175
176 177 178 179 180 181 182 183
184 185 186 187 188 189 190 191
192 193 194 195 196 197 198 199
200 201 202 203 204 205 206 207
208 209 210 211 212 213 214 215
216 217 218 219 220 221 222 223
224 225 226 227 228 229 230 231
232 233 234 235 236 237 238 239
240 241 242 243 244 245 246 247
248 249 250 251 252 253 254 255
256>;
};
clocks {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
clk32k_in: clock@0 {
compatible = "fixed-clock";
reg = <0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
};
gpio-keys {
compatible = "gpio-keys";
lid {
label = "Lid";
gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
linux,input-type = <5>;
linux,code = <KEY_RESERVED>;
debounce-interval = <1>;
gpio-key,wakeup;
};
power {
label = "Power";
gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
debounce-interval = <30>;
gpio-key,wakeup;
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
vdd_mux: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "+VDD_MUX";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
regulator-always-on;
regulator-boot-on;
};
vdd_5v0_sys: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "+5V_SYS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vdd_mux>;
};
vdd_3v3_sys: regulator@2 {
compatible = "regulator-fixed";
reg = <2>;
regulator-name = "+3.3V_SYS";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vdd_mux>;
};
vdd_3v3_run: regulator@3 {
compatible = "regulator-fixed";
reg = <3>;
regulator-name = "+3.3V_RUN";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&vdd_3v3_sys>;
};
vdd_3v3_hdmi: regulator@4 {
compatible = "regulator-fixed";
reg = <4>;
regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vdd_3v3_run>;
};
vdd_led: regulator@5 {
compatible = "regulator-fixed";
reg = <5>;
regulator-name = "+VDD_LED";
gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&vdd_mux>;
};
vdd_5v0_ts: regulator@6 {
compatible = "regulator-fixed";
reg = <6>;
regulator-name = "+5V_VDD_TS_SW";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&vdd_5v0_sys>;
};
vdd_usb1_vbus: regulator@7 {
compatible = "regulator-fixed";
reg = <7>;
regulator-name = "+5V_USB_HS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
enable-active-high;
gpio-open-drain;
vin-supply = <&vdd_5v0_sys>;
};
vdd_usb3_vbus: regulator@8 {
compatible = "regulator-fixed";
reg = <8>;
regulator-name = "+5V_USB_SS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
enable-active-high;
gpio-open-drain;
vin-supply = <&vdd_5v0_sys>;
};
vdd_3v3_panel: regulator@9 {
compatible = "regulator-fixed";
reg = <9>;
regulator-name = "+3.3V_PANEL";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&vdd_3v3_run>;
};
vdd_3v3_lp0: regulator@10 {
compatible = "regulator-fixed";
reg = <10>;
regulator-name = "+3.3V_LP0";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
/*
* TODO: find a way to wire this up with the USB EHCI
* controllers so that it can be enabled on demand.
*/
regulator-always-on;
gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&vdd_3v3_sys>;
};
vdd_hdmi_pll: regulator@11 {
compatible = "regulator-fixed";
reg = <11>;
regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
vin-supply = <&vdd_1v05_run>;
};
vdd_5v0_hdmi: regulator@12 {
compatible = "regulator-fixed";
reg = <12>;
regulator-name = "+5V_HDMI_CON";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&vdd_5v0_sys>;
};
};
sound {
nvidia,audio-routing =
"Headphones", "HPR",
"Headphones", "HPL",
"Speakers", "SPKR",
"Speakers", "SPKL",
"Mic Jack", "MICBIAS",
"DMICL", "Int Mic",
"DMICR", "Int Mic",
"IN34", "Mic Jack";
nvidia,i2s-controller = <&tegra_i2s1>;
nvidia,audio-codec = <&acodec>;
clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
<&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
<&tegra_car TEGRA124_CLK_EXTERN1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
nvidia,mic-det-gpios =
<&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
};
ARM: tegra: nyan: Add gpio-restart node The Nyan Chromebooks have a GPIO line dedicated to restarting the system. Using this line will make sure that the TPM is restarted as well. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:26 +08:00
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
priority = <200>;
};
ARM: tegra: Move generic parts out of the nyan-big DT In preparation for adding the DT for the nyan-blaze board. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-03-18 17:52:17 +08:00
};
#include "cros-ec-keyboard.dtsi"