openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
linux/arch/arm/mach-pxa/mfp-pxa25x.h

226 lines
8.8 KiB
C
Raw Normal View History

[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
#ifndef __ASM_ARCH_MFP_PXA25X_H
#define __ASM_ARCH_MFP_PXA25X_H
ARM: pxa: make more mach/*.h files local Lots of header files are never included outside of a mach-pxa directory and do not need to be made visible in include/mach, so let's just move them all down one level. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-01-30 17:45:33 +08:00
#include "mfp-pxa2xx.h"
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
/* GPIO */
#define GPIO2_GPIO MFP_CFG_IN(GPIO2, AF0)
#define GPIO3_GPIO MFP_CFG_IN(GPIO3, AF0)
#define GPIO4_GPIO MFP_CFG_IN(GPIO4, AF0)
#define GPIO5_GPIO MFP_CFG_IN(GPIO5, AF0)
#define GPIO6_GPIO MFP_CFG_IN(GPIO6, AF0)
#define GPIO7_GPIO MFP_CFG_IN(GPIO7, AF0)
#define GPIO8_GPIO MFP_CFG_IN(GPIO8, AF0)
#define GPIO1_RST MFP_CFG_IN(GPIO1, AF1)
/* Crystal and Clock Signals */
#define GPIO10_RTCCLK MFP_CFG_OUT(GPIO10, AF1, DRIVE_LOW)
[ARM] pxa: fix typo in pxa25x MFP definitions Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-21 16:20:54 +08:00
#define GPIO70_RTCCLK MFP_CFG_OUT(GPIO70, AF1, DRIVE_LOW)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
#define GPIO7_48MHz MFP_CFG_OUT(GPIO7, AF1, DRIVE_LOW)
#define GPIO11_3_6MHz MFP_CFG_OUT(GPIO11, AF1, DRIVE_LOW)
#define GPIO71_3_6MHz MFP_CFG_OUT(GPIO71, AF1, DRIVE_LOW)
#define GPIO12_32KHz MFP_CFG_OUT(GPIO12, AF1, DRIVE_LOW)
#define GPIO72_32kHz MFP_CFG_OUT(GPIO72, AF1, DRIVE_LOW)
/* SDRAM and Static Memory I/O Signals */
#define GPIO15_nCS_1 MFP_CFG_OUT(GPIO15, AF2, DRIVE_HIGH)
#define GPIO78_nCS_2 MFP_CFG_OUT(GPIO78, AF2, DRIVE_HIGH)
#define GPIO79_nCS_3 MFP_CFG_OUT(GPIO79, AF2, DRIVE_HIGH)
#define GPIO80_nCS_4 MFP_CFG_OUT(GPIO80, AF2, DRIVE_HIGH)
#define GPIO33_nCS_5 MFP_CFG_OUT(GPIO33, AF2, DRIVE_HIGH)
/* Miscellaneous I/O and DMA Signals */
#define GPIO18_RDY MFP_CFG_IN(GPIO18, AF1)
#define GPIO20_DREQ_0 MFP_CFG_IN(GPIO20, AF1)
#define GPIO19_DREQ_1 MFP_CFG_IN(GPIO19, AF1)
/* Alternate Bus Master Mode I/O Signals */
#define GPIO13_MBGNT MFP_CFG_OUT(GPIO13, AF2, DRIVE_LOW)
#define GPIO73_MBGNT MFP_CFG_OUT(GPIO73, AF1, DRIVE_LOW)
#define GPIO14_MBREQ MFP_CFG_IN(GPIO14, AF1)
#define GPIO66_MBREQ MFP_CFG_IN(GPIO66, AF1)
/* PC CARD */
#define GPIO52_nPCE_1 MFP_CFG_OUT(GPIO52, AF2, DRIVE_HIGH)
#define GPIO53_nPCE_2 MFP_CFG_OUT(GPIO53, AF2, DRIVE_HIGH)
#define GPIO55_nPREG MFP_CFG_OUT(GPIO55, AF2, DRIVE_HIGH)
#define GPIO50_nPIOR MFP_CFG_OUT(GPIO50, AF2, DRIVE_HIGH)
#define GPIO51_nPIOW MFP_CFG_OUT(GPIO51, AF2, DRIVE_HIGH)
#define GPIO49_nPWE MFP_CFG_OUT(GPIO49, AF2, DRIVE_HIGH)
#define GPIO48_nPOE MFP_CFG_OUT(GPIO48, AF2, DRIVE_HIGH)
#define GPIO57_nIOIS16 MFP_CFG_IN(GPIO57, AF1)
#define GPIO56_nPWAIT MFP_CFG_IN(GPIO56, AF1)
#define GPIO54_nPSKTSEL MFP_CFG_OUT(GPIO54, AF2, DRIVE_HIGH)
/* FFUART */
#define GPIO34_FFUART_RXD MFP_CFG_IN(GPIO34, AF1)
#define GPIO35_FFUART_CTS MFP_CFG_IN(GPIO35, AF1)
#define GPIO36_FFUART_DCD MFP_CFG_IN(GPIO36, AF1)
#define GPIO37_FFUART_DSR MFP_CFG_IN(GPIO37, AF1)
#define GPIO38_FFUART_RI MFP_CFG_IN(GPIO38, AF1)
#define GPIO39_FFUART_TXD MFP_CFG_OUT(GPIO39, AF2, DRIVE_HIGH)
#define GPIO40_FFUART_DTR MFP_CFG_OUT(GPIO40, AF2, DRIVE_HIGH)
#define GPIO41_FFUART_RTS MFP_CFG_OUT(GPIO41, AF2, DRIVE_HIGH)
/* BTUART */
#define GPIO42_BTUART_RXD MFP_CFG_IN(GPIO42, AF1)
#define GPIO43_BTUART_TXD MFP_CFG_OUT(GPIO43, AF2, DRIVE_HIGH)
#define GPIO44_BTUART_CTS MFP_CFG_IN(GPIO44, AF1)
#define GPIO45_BTUART_RTS MFP_CFG_OUT(GPIO45, AF2, DRIVE_HIGH)
/* STUART */
#define GPIO46_STUART_RXD MFP_CFG_IN(GPIO46, AF2)
#define GPIO47_STUART_TXD MFP_CFG_OUT(GPIO47, AF1, DRIVE_HIGH)
/* HWUART */
#define GPIO42_HWUART_RXD MFP_CFG_IN(GPIO42, AF3)
#define GPIO43_HWUART_TXD MFP_CFG_OUT(GPIO43, AF3, DRIVE_HIGH)
#define GPIO44_HWUART_CTS MFP_CFG_IN(GPIO44, AF3)
#define GPIO45_HWUART_RTS MFP_CFG_OUT(GPIO45, AF3, DRIVE_HIGH)
#define GPIO48_HWUART_TXD MFP_CFG_OUT(GPIO48, AF1, DRIVE_HIGH)
#define GPIO49_HWUART_RXD MFP_CFG_IN(GPIO49, AF1)
#define GPIO50_HWUART_CTS MFP_CFG_IN(GPIO50, AF1)
#define GPIO51_HWUART_RTS MFP_CFG_OUT(GPIO51, AF1, DRIVE_HIGH)
/* FICP */
#define GPIO46_FICP_RXD MFP_CFG_IN(GPIO46, AF1)
#define GPIO47_FICP_TXD MFP_CFG_OUT(GPIO47, AF2, DRIVE_HIGH)
/* PWM 0/1 */
#define GPIO16_PWM0_OUT MFP_CFG_OUT(GPIO16, AF2, DRIVE_LOW)
#define GPIO17_PWM1_OUT MFP_CFG_OUT(GPIO17, AF2, DRIVE_LOW)
/* AC97 */
#define GPIO28_AC97_BITCLK MFP_CFG_IN(GPIO28, AF1)
#define GPIO29_AC97_SDATA_IN_0 MFP_CFG_IN(GPIO29, AF1)
#define GPIO30_AC97_SDATA_OUT MFP_CFG_OUT(GPIO30, AF2, DRIVE_LOW)
#define GPIO31_AC97_SYNC MFP_CFG_OUT(GPIO31, AF2, DRIVE_LOW)
#define GPIO32_AC97_SDATA_IN_1 MFP_CFG_IN(GPIO32, AF1)
/* I2S */
#define GPIO28_I2S_BITCLK_IN MFP_CFG_IN(GPIO28, AF2)
#define GPIO28_I2S_BITCLK_OUT MFP_CFG_OUT(GPIO28, AF1, DRIVE_LOW)
#define GPIO29_I2S_SDATA_IN MFP_CFG_IN(GPIO29, AF2)
#define GPIO30_I2S_SDATA_OUT MFP_CFG_OUT(GPIO30, AF1, DRIVE_LOW)
#define GPIO31_I2S_SYNC MFP_CFG_OUT(GPIO31, AF1, DRIVE_LOW)
#define GPIO32_I2S_SYSCLK MFP_CFG_OUT(GPIO32, AF1, DRIVE_LOW)
/* SSP 1 */
#define GPIO23_SSP1_SCLK MFP_CFG_OUT(GPIO23, AF2, DRIVE_LOW)
#define GPIO24_SSP1_SFRM MFP_CFG_OUT(GPIO24, AF2, DRIVE_LOW)
#define GPIO25_SSP1_TXD MFP_CFG_OUT(GPIO25, AF2, DRIVE_LOW)
#define GPIO26_SSP1_RXD MFP_CFG_IN(GPIO26, AF1)
#define GPIO27_SSP1_EXTCLK MFP_CFG_IN(GPIO27, AF1)
/* SSP 2 - NSSP */
#define GPIO81_SSP2_CLK_OUT MFP_CFG_OUT(GPIO81, AF1, DRIVE_LOW)
#define GPIO81_SSP2_CLK_IN MFP_CFG_IN(GPIO81, AF1)
#define GPIO82_SSP2_FRM_OUT MFP_CFG_OUT(GPIO82, AF1, DRIVE_LOW)
#define GPIO82_SSP2_FRM_IN MFP_CFG_IN(GPIO82, AF1)
#define GPIO83_SSP2_TXD MFP_CFG_OUT(GPIO83, AF1, DRIVE_LOW)
#define GPIO83_SSP2_RXD MFP_CFG_IN(GPIO83, AF2)
#define GPIO84_SSP2_TXD MFP_CFG_OUT(GPIO84, AF1, DRIVE_LOW)
#define GPIO84_SSP2_RXD MFP_CFG_IN(GPIO84, AF2)
/* MMC */
#define GPIO6_MMC_CLK MFP_CFG_OUT(GPIO6, AF1, DRIVE_LOW)
#define GPIO8_MMC_CS0 MFP_CFG_OUT(GPIO8, AF1, DRIVE_LOW)
#define GPIO9_MMC_CS1 MFP_CFG_OUT(GPIO9, AF1, DRIVE_LOW)
#define GPIO34_MMC_CS0 MFP_CFG_OUT(GPIO34, AF2, DRIVE_LOW)
#define GPIO39_MMC_CS1 MFP_CFG_OUT(GPIO39, AF1, DRIVE_LOW)
#define GPIO53_MMC_CLK MFP_CFG_OUT(GPIO53, AF1, DRIVE_LOW)
#define GPIO54_MMC_CLK MFP_CFG_OUT(GPIO54, AF1, DRIVE_LOW)
#define GPIO69_MMC_CLK MFP_CFG_OUT(GPIO69, AF1, DRIVE_LOW)
#define GPIO67_MMC_CS0 MFP_CFG_OUT(GPIO67, AF1, DRIVE_LOW)
#define GPIO68_MMC_CS1 MFP_CFG_OUT(GPIO68, AF1, DRIVE_LOW)
/* LCD */
#define GPIO58_LCD_LDD_0 MFP_CFG_OUT(GPIO58, AF2, DRIVE_LOW)
#define GPIO59_LCD_LDD_1 MFP_CFG_OUT(GPIO59, AF2, DRIVE_LOW)
#define GPIO60_LCD_LDD_2 MFP_CFG_OUT(GPIO60, AF2, DRIVE_LOW)
#define GPIO61_LCD_LDD_3 MFP_CFG_OUT(GPIO61, AF2, DRIVE_LOW)
#define GPIO62_LCD_LDD_4 MFP_CFG_OUT(GPIO62, AF2, DRIVE_LOW)
#define GPIO63_LCD_LDD_5 MFP_CFG_OUT(GPIO63, AF2, DRIVE_LOW)
#define GPIO64_LCD_LDD_6 MFP_CFG_OUT(GPIO64, AF2, DRIVE_LOW)
#define GPIO65_LCD_LDD_7 MFP_CFG_OUT(GPIO65, AF2, DRIVE_LOW)
#define GPIO66_LCD_LDD_8 MFP_CFG_OUT(GPIO66, AF2, DRIVE_LOW)
#define GPIO67_LCD_LDD_9 MFP_CFG_OUT(GPIO67, AF2, DRIVE_LOW)
#define GPIO68_LCD_LDD_10 MFP_CFG_OUT(GPIO68, AF2, DRIVE_LOW)
#define GPIO69_LCD_LDD_11 MFP_CFG_OUT(GPIO69, AF2, DRIVE_LOW)
#define GPIO70_LCD_LDD_12 MFP_CFG_OUT(GPIO70, AF2, DRIVE_LOW)
#define GPIO71_LCD_LDD_13 MFP_CFG_OUT(GPIO71, AF2, DRIVE_LOW)
#define GPIO72_LCD_LDD_14 MFP_CFG_OUT(GPIO72, AF2, DRIVE_LOW)
#define GPIO73_LCD_LDD_15 MFP_CFG_OUT(GPIO73, AF2, DRIVE_LOW)
#define GPIO74_LCD_FCLK MFP_CFG_OUT(GPIO74, AF2, DRIVE_LOW)
#define GPIO75_LCD_LCLK MFP_CFG_OUT(GPIO75, AF2, DRIVE_LOW)
#define GPIO76_LCD_PCLK MFP_CFG_OUT(GPIO76, AF2, DRIVE_LOW)
[ARM] pxa: fix typo in pxa25x MFP definitions Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-21 16:20:54 +08:00
#define GPIO77_LCD_BIAS MFP_CFG_OUT(GPIO77, AF2, DRIVE_LOW)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 18:12:04 +08:00
#ifdef CONFIG_CPU_PXA26x
/* GPIO */
#define GPIO85_GPIO MFP_CFG_IN(GPIO85, AF0)
#define GPIO86_GPIO MFP_CFG_IN(GPIO86, AF1)
#define GPIO87_GPIO MFP_CFG_IN(GPIO87, AF1)
#define GPIO88_GPIO MFP_CFG_IN(GPIO88, AF1)
#define GPIO89_GPIO MFP_CFG_IN(GPIO89, AF1)
/* SDRAM */
#define GPIO86_nSDCS2 MFP_CFG_OUT(GPIO86, AF0, DRIVE_HIGH)
#define GPIO87_nSDCS3 MFP_CFG_OUT(GPIO87, AF0, DRIVE_HIGH)
#define GPIO88_RDnWR MFP_CFG_OUT(GPIO88, AF0, DRIVE_HIGH)
/* USB */
#define GPIO9_USB_RCV MFP_CFG_IN(GPIO9, AF1)
#define GPIO32_USB_VP MFP_CFG_IN(GPIO32, AF2)
#define GPIO34_USB_VM MFP_CFG_IN(GPIO34, AF2)
#define GPIO39_USB_VPO MFP_CFG_OUT(GPIO39, AF3, DRIVE_LOW)
#define GPIO56_USB_VMO MFP_CFG_OUT(GPIO56, AF1, DRIVE_LOW)
#define GPIO57_USB_nOE MFP_CFG_OUT(GPIO57, AF1, DRIVE_HIGH)
/* ASSP */
#define GPIO28_ASSP_BITCLK_IN MFP_CFG_IN(GPIO28, AF3)
#define GPIO28_ASSP_BITCLK_OUT MFP_CFG_OUT(GPIO28, AF3, DRIVE_LOW)
#define GPIO29_ASSP_RXD MFP_CFG_IN(GPIO29, AF3)
#define GPIO30_ASSP_TXD MFP_CFG_OUT(GPIO30, AF3, DRIVE_LOW)
#define GPIO31_ASSP_SFRM_IN MFP_CFG_IN(GPIO31, AF1)
#define GPIO31_ASSP_SFRM_OUT MFP_CFG_OUT(GPIO31, AF3, DRIVE_LOW)
[ARM] pxa: fix the incorrect naming of AC97 reset pin config for pxa26x GPIO89_AC97_nRESET is really a PXA26x specific option and was incorrectly named. Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2010-01-04 15:22:18 +08:00
/* AC97 */
#define GPIO89_AC97_nRESET MFP_CFG_OUT(GPIO89, AF0, DRIVE_HIGH)
#endif /* CONFIG_CPU_PXA26x */
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 18:12:04 +08:00
[ARM] pxa: simplify the LCD pin configuration for pxa25x platforms There are only limited possible LCD pin configurations for pxa25x platforms, simplify this by macro. Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2010-01-04 11:25:10 +08:00
/* commonly used pin configurations */
#define GPIOxx_LCD_16BPP \
GPIO58_LCD_LDD_0, \
GPIO59_LCD_LDD_1, \
GPIO60_LCD_LDD_2, \
GPIO61_LCD_LDD_3, \
GPIO62_LCD_LDD_4, \
GPIO63_LCD_LDD_5, \
GPIO64_LCD_LDD_6, \
GPIO65_LCD_LDD_7, \
GPIO66_LCD_LDD_8, \
GPIO67_LCD_LDD_9, \
GPIO68_LCD_LDD_10, \
GPIO69_LCD_LDD_11, \
GPIO70_LCD_LDD_12, \
GPIO71_LCD_LDD_13, \
GPIO72_LCD_LDD_14, \
GPIO73_LCD_LDD_15
#define GPIOxx_LCD_DSTN_16BPP \
GPIOxx_LCD_16BPP, \
GPIO74_LCD_FCLK, \
GPIO75_LCD_LCLK, \
GPIO76_LCD_PCLK
#define GPIOxx_LCD_TFT_16BPP \
GPIOxx_LCD_16BPP, \
GPIO74_LCD_FCLK, \
GPIO75_LCD_LCLK, \
GPIO76_LCD_PCLK, \
GPIO77_LCD_BIAS
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
#endif /* __ASM_ARCH_MFP_PXA25X_H */