openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
linux/drivers/nfc/st21nfca/Makefile

10 lines
228 B
Makefile
Raw Normal View History

NFC: ST21NFCA: Add driver for STMicroelectronics ST21NFCA NFC Chip Add driver for STMicroelectronics ST21NFCA NFC controller. ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as communication protocol. Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B. It is using proprietary gate 15 for ISO14443-3 such as type 1 & type 2 tags. It is using proprietary gate 14 for type F tags. ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration. Standard gate for ISO14443-4 A (13) & B (11) are also used. ST21NFCA specific mecanism: One particular point to notice for the data handling is that frame does not contain any length value. Therefore the i2c part of this driver is managing the reception with a read length sequence until the end of frame (0x7e) is reached. In order to avoid conflict between sof & eof a mecanism called byte stuffing concist of an escape byte (0x7d) insertion before special byte (0x7e, 0x7d). The special byte is then xored with 0x20. In this driver, When data are available in the CLF, the interrupt gpio is driven to active state and triggered an interrupt. Once the i2c_master_recv start, the interrupt gpio is driven to idle state until its complete. If the frame is incomplete or data are still available, interrupts will be triggered again. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-03-25 13:51:47 +08:00
#
# Makefile for ST21NFCA HCI based NFC driver
#
NFC: st21nfca: Add support for proprietary commands Add support for proprietary commands useful mainly for factory testings. Here is a list: - FACTORY_MODE: Allow to set the driver into a mode where no secure element are activated. It does not consider any NFC_ATTR_VENDOR_DATA. - HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes command. It does not consider any NFC_ATTR_VENDOR_DATA. - HCI_DM_PUT_DATA: Allow to configure specific CLF registry as for example RF trimmings or low level drivers configurations (I2C, SPI, SWP). - HCI_DM_UPDATE_AID: Allow to configure an AID routing into the CLF routing table following RF technology, CLF mode or protocol. - HCI_DM_GET_INFO: Allow to retrieve CLF information. - HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as low level drivers configurations or RF trimmings. - HCI_DM_LOAD: Allow to load a firmware into the CLF. A complete packet can be more than 8KB. - HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF configuration changes without CLF power off. - HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example the white list). - HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF technology. When using this command to anti-collision is done. - HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF connectivity. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2015-10-26 14:50:11 +08:00
st21nfca_hci-objs = core.o dep.o se.o vendor_cmds.o
NFC: st21nfca: Fix potential depmod dependency cycle In the previous makefile 2 modules were generated for CONFIG_NFC_ST21NFCA (st21nfca.ko and st21nfca_dep.ko). Merge both of them into st21nfca_hci.ko and fix a potential depmod dependency cycle, similar to the one we saw on st21nfcb: depmod: WARNING: found 6 modules in dependency cycles! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/st21nfcb.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/ndlc.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/rfkill/rfkill.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nfc.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nci/nci.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/lib/crc-ccitt.ko in dependency cycle! ./scripts/depmod.sh: line 57: 23387 Segmentation fault (core dumped) "$DEPMOD" "$@" "$KERNELRELEASE" $SYMBOL_PREFIX make: *** [_modinst_post] Error 139 Reported-by: Daniel Wagner <wagi@monom.org> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-04 05:30:31 +08:00
obj-$(CONFIG_NFC_ST21NFCA) += st21nfca_hci.o
NFC: ST21NFCA: Add driver for STMicroelectronics ST21NFCA NFC Chip Add driver for STMicroelectronics ST21NFCA NFC controller. ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as communication protocol. Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B. It is using proprietary gate 15 for ISO14443-3 such as type 1 & type 2 tags. It is using proprietary gate 14 for type F tags. ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration. Standard gate for ISO14443-4 A (13) & B (11) are also used. ST21NFCA specific mecanism: One particular point to notice for the data handling is that frame does not contain any length value. Therefore the i2c part of this driver is managing the reception with a read length sequence until the end of frame (0x7e) is reached. In order to avoid conflict between sof & eof a mecanism called byte stuffing concist of an escape byte (0x7d) insertion before special byte (0x7e, 0x7d). The special byte is then xored with 0x20. In this driver, When data are available in the CLF, the interrupt gpio is driven to active state and triggered an interrupt. Once the i2c_master_recv start, the interrupt gpio is driven to idle state until its complete. If the frame is incomplete or data are still available, interrupts will be triggered again. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-03-25 13:51:47 +08:00
NFC: st21nfca: Fix potential depmod dependency cycle In the previous makefile 2 modules were generated for CONFIG_NFC_ST21NFCA (st21nfca.ko and st21nfca_dep.ko). Merge both of them into st21nfca_hci.ko and fix a potential depmod dependency cycle, similar to the one we saw on st21nfcb: depmod: WARNING: found 6 modules in dependency cycles! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/st21nfcb.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/ndlc.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/rfkill/rfkill.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nfc.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nci/nci.ko in dependency cycle! depmod: WARNING: /lib/modules/3.17.0-rc3-00002-g7505cea/kernel/lib/crc-ccitt.ko in dependency cycle! ./scripts/depmod.sh: line 57: 23387 Segmentation fault (core dumped) "$DEPMOD" "$@" "$KERNELRELEASE" $SYMBOL_PREFIX make: *** [_modinst_post] Error 139 Reported-by: Daniel Wagner <wagi@monom.org> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-04 05:30:31 +08:00
st21nfca_i2c-objs = i2c.o
NFC: ST21NFCA: Add driver for STMicroelectronics ST21NFCA NFC Chip Add driver for STMicroelectronics ST21NFCA NFC controller. ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as communication protocol. Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B. It is using proprietary gate 15 for ISO14443-3 such as type 1 & type 2 tags. It is using proprietary gate 14 for type F tags. ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration. Standard gate for ISO14443-4 A (13) & B (11) are also used. ST21NFCA specific mecanism: One particular point to notice for the data handling is that frame does not contain any length value. Therefore the i2c part of this driver is managing the reception with a read length sequence until the end of frame (0x7e) is reached. In order to avoid conflict between sof & eof a mecanism called byte stuffing concist of an escape byte (0x7d) insertion before special byte (0x7e, 0x7d). The special byte is then xored with 0x20. In this driver, When data are available in the CLF, the interrupt gpio is driven to active state and triggered an interrupt. Once the i2c_master_recv start, the interrupt gpio is driven to idle state until its complete. If the frame is incomplete or data are still available, interrupts will be triggered again. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-03-25 13:51:47 +08:00
obj-$(CONFIG_NFC_ST21NFCA_I2C) += st21nfca_i2c.o