linux/drivers/soc/qcom/rpmh-rsc.c

829 lines
20 KiB
C
Raw Normal View History

drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
*/
#define pr_fmt(fmt) "%s " fmt, KBUILD_MODNAME
#include <linux/atomic.h>
#include <linux/cpu_pm.h>
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/list.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <soc/qcom/cmd-db.h>
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
#include <soc/qcom/tcs.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include "rpmh-internal.h"
#define CREATE_TRACE_POINTS
#include "trace-rpmh.h"
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
#define RSC_DRV_TCS_OFFSET 672
#define RSC_DRV_CMD_OFFSET 20
/* DRV HW Solver Configuration Information Register */
#define DRV_SOLVER_CONFIG 0x04
#define DRV_HW_SOLVER_MASK 1
#define DRV_HW_SOLVER_SHIFT 24
/* DRV TCS Configuration Information Register */
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
#define DRV_PRNT_CHLD_CONFIG 0x0C
#define DRV_NUM_TCS_MASK 0x3F
#define DRV_NUM_TCS_SHIFT 6
#define DRV_NCPT_MASK 0x1F
#define DRV_NCPT_SHIFT 27
/* Register offsets */
#define RSC_DRV_IRQ_ENABLE 0x00
#define RSC_DRV_IRQ_STATUS 0x04
#define RSC_DRV_IRQ_CLEAR 0x08
#define RSC_DRV_CMD_WAIT_FOR_CMPL 0x10
#define RSC_DRV_CONTROL 0x14
#define RSC_DRV_STATUS 0x18
#define RSC_DRV_CMD_ENABLE 0x1C
#define RSC_DRV_CMD_MSGID 0x30
#define RSC_DRV_CMD_ADDR 0x34
#define RSC_DRV_CMD_DATA 0x38
#define RSC_DRV_CMD_STATUS 0x3C
#define RSC_DRV_CMD_RESP_DATA 0x40
#define TCS_AMC_MODE_ENABLE BIT(16)
#define TCS_AMC_MODE_TRIGGER BIT(24)
/* TCS CMD register bit mask */
#define CMD_MSGID_LEN 8
#define CMD_MSGID_RESP_REQ BIT(8)
#define CMD_MSGID_WRITE BIT(16)
#define CMD_STATUS_ISSUED BIT(8)
#define CMD_STATUS_COMPL BIT(16)
static u32 read_tcs_cmd(struct rsc_drv *drv, int reg, int tcs_id, int cmd_id)
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
{
return readl_relaxed(drv->tcs_base + RSC_DRV_TCS_OFFSET * tcs_id + reg +
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
RSC_DRV_CMD_OFFSET * cmd_id);
}
static u32 read_tcs_reg(struct rsc_drv *drv, int reg, int tcs_id)
{
return readl_relaxed(drv->tcs_base + RSC_DRV_TCS_OFFSET * tcs_id + reg);
}
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
static void write_tcs_cmd(struct rsc_drv *drv, int reg, int tcs_id, int cmd_id,
u32 data)
{
writel_relaxed(data, drv->tcs_base + RSC_DRV_TCS_OFFSET * tcs_id + reg +
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
RSC_DRV_CMD_OFFSET * cmd_id);
}
static void write_tcs_reg(struct rsc_drv *drv, int reg, int tcs_id, u32 data)
{
writel_relaxed(data, drv->tcs_base + RSC_DRV_TCS_OFFSET * tcs_id + reg);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
}
static void write_tcs_reg_sync(struct rsc_drv *drv, int reg, int tcs_id,
u32 data)
{
writel(data, drv->tcs_base + RSC_DRV_TCS_OFFSET * tcs_id + reg);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
for (;;) {
if (data == readl(drv->tcs_base + reg +
RSC_DRV_TCS_OFFSET * tcs_id))
break;
udelay(1);
}
}
static bool tcs_is_free(struct rsc_drv *drv, int tcs_id)
{
return !test_bit(tcs_id, drv->tcs_in_use) &&
read_tcs_reg(drv, RSC_DRV_STATUS, tcs_id);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
}
static struct tcs_group *get_tcs_of_type(struct rsc_drv *drv, int type)
{
return &drv->tcs[type];
}
static int tcs_invalidate(struct rsc_drv *drv, int type)
{
int m;
struct tcs_group *tcs;
tcs = get_tcs_of_type(drv, type);
spin_lock(&tcs->lock);
if (bitmap_empty(tcs->slots, MAX_TCS_SLOTS)) {
spin_unlock(&tcs->lock);
return 0;
}
for (m = tcs->offset; m < tcs->offset + tcs->num_tcs; m++) {
if (!tcs_is_free(drv, m)) {
spin_unlock(&tcs->lock);
return -EAGAIN;
}
write_tcs_reg_sync(drv, RSC_DRV_CMD_ENABLE, m, 0);
write_tcs_reg_sync(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, m, 0);
}
bitmap_zero(tcs->slots, MAX_TCS_SLOTS);
spin_unlock(&tcs->lock);
return 0;
}
/**
* rpmh_rsc_invalidate - Invalidate sleep and wake TCSes
*
* @drv: the RSC controller
*/
int rpmh_rsc_invalidate(struct rsc_drv *drv)
{
int ret;
ret = tcs_invalidate(drv, SLEEP_TCS);
if (!ret)
ret = tcs_invalidate(drv, WAKE_TCS);
return ret;
}
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
static struct tcs_group *get_tcs_for_msg(struct rsc_drv *drv,
const struct tcs_request *msg)
{
int type;
struct tcs_group *tcs;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
switch (msg->state) {
case RPMH_ACTIVE_ONLY_STATE:
type = ACTIVE_TCS;
break;
case RPMH_WAKE_ONLY_STATE:
type = WAKE_TCS;
break;
case RPMH_SLEEP_STATE:
type = SLEEP_TCS;
break;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
default:
return ERR_PTR(-EINVAL);
}
/*
* If we are making an active request on a RSC that does not have a
* dedicated TCS for active state use, then re-purpose a wake TCS to
* send active votes.
*/
tcs = get_tcs_of_type(drv, type);
if (msg->state == RPMH_ACTIVE_ONLY_STATE && !tcs->num_tcs)
tcs = get_tcs_of_type(drv, WAKE_TCS);
return tcs;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
}
static const struct tcs_request *get_req_from_tcs(struct rsc_drv *drv,
int tcs_id)
{
struct tcs_group *tcs;
int i;
for (i = 0; i < TCS_TYPE_NR; i++) {
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
tcs = &drv->tcs[i];
if (tcs->mask & BIT(tcs_id))
return tcs->req[tcs_id - tcs->offset];
}
return NULL;
}
static void __tcs_set_trigger(struct rsc_drv *drv, int tcs_id, bool trigger)
{
u32 enable;
/*
* HW req: Clear the DRV_CONTROL and enable TCS again
* While clearing ensure that the AMC mode trigger is cleared
* and then the mode enable is cleared.
*/
enable = read_tcs_reg(drv, RSC_DRV_CONTROL, tcs_id);
enable &= ~TCS_AMC_MODE_TRIGGER;
write_tcs_reg_sync(drv, RSC_DRV_CONTROL, tcs_id, enable);
enable &= ~TCS_AMC_MODE_ENABLE;
write_tcs_reg_sync(drv, RSC_DRV_CONTROL, tcs_id, enable);
if (trigger) {
/* Enable the AMC mode on the TCS and then trigger the TCS */
enable = TCS_AMC_MODE_ENABLE;
write_tcs_reg_sync(drv, RSC_DRV_CONTROL, tcs_id, enable);
enable |= TCS_AMC_MODE_TRIGGER;
write_tcs_reg_sync(drv, RSC_DRV_CONTROL, tcs_id, enable);
}
}
static void enable_tcs_irq(struct rsc_drv *drv, int tcs_id, bool enable)
{
u32 data;
data = read_tcs_reg(drv, RSC_DRV_IRQ_ENABLE, 0);
if (enable)
data |= BIT(tcs_id);
else
data &= ~BIT(tcs_id);
write_tcs_reg(drv, RSC_DRV_IRQ_ENABLE, 0, data);
}
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
/**
* tcs_tx_done: TX Done interrupt handler
*/
static irqreturn_t tcs_tx_done(int irq, void *p)
{
struct rsc_drv *drv = p;
int i, j, err = 0;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
unsigned long irq_status;
const struct tcs_request *req;
struct tcs_cmd *cmd;
irq_status = read_tcs_reg(drv, RSC_DRV_IRQ_STATUS, 0);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
for_each_set_bit(i, &irq_status, BITS_PER_LONG) {
req = get_req_from_tcs(drv, i);
if (!req) {
WARN_ON(1);
goto skip;
}
err = 0;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
for (j = 0; j < req->num_cmds; j++) {
u32 sts;
cmd = &req->cmds[j];
sts = read_tcs_cmd(drv, RSC_DRV_CMD_STATUS, i, j);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
if (!(sts & CMD_STATUS_ISSUED) ||
((req->wait_for_compl || cmd->wait) &&
!(sts & CMD_STATUS_COMPL))) {
pr_err("Incomplete request: %s: addr=%#x data=%#x",
drv->name, cmd->addr, cmd->data);
err = -EIO;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
}
}
trace_rpmh_tx_done(drv, i, req, err);
/*
* If wake tcs was re-purposed for sending active
* votes, clear AMC trigger & enable modes and
* disable interrupt for this TCS
*/
if (!drv->tcs[ACTIVE_TCS].num_tcs)
__tcs_set_trigger(drv, i, false);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
skip:
/* Reclaim the TCS */
write_tcs_reg(drv, RSC_DRV_CMD_ENABLE, i, 0);
write_tcs_reg(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, i, 0);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
write_tcs_reg(drv, RSC_DRV_IRQ_CLEAR, 0, BIT(i));
spin_lock(&drv->lock);
clear_bit(i, drv->tcs_in_use);
/*
* Disable interrupt for WAKE TCS to avoid being
* spammed with interrupts coming when the solver
* sends its wake votes.
*/
if (!drv->tcs[ACTIVE_TCS].num_tcs)
enable_tcs_irq(drv, i, false);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
spin_unlock(&drv->lock);
if (req)
rpmh_tx_done(req, err);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
}
return IRQ_HANDLED;
}
static void __tcs_buffer_write(struct rsc_drv *drv, int tcs_id, int cmd_id,
const struct tcs_request *msg)
{
u32 msgid, cmd_msgid;
u32 cmd_enable = 0;
u32 cmd_complete;
struct tcs_cmd *cmd;
int i, j;
cmd_msgid = CMD_MSGID_LEN;
cmd_msgid |= msg->wait_for_compl ? CMD_MSGID_RESP_REQ : 0;
cmd_msgid |= CMD_MSGID_WRITE;
cmd_complete = read_tcs_reg(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, tcs_id);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
for (i = 0, j = cmd_id; i < msg->num_cmds; i++, j++) {
cmd = &msg->cmds[i];
cmd_enable |= BIT(j);
cmd_complete |= cmd->wait << j;
msgid = cmd_msgid;
msgid |= cmd->wait ? CMD_MSGID_RESP_REQ : 0;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
write_tcs_cmd(drv, RSC_DRV_CMD_MSGID, tcs_id, j, msgid);
write_tcs_cmd(drv, RSC_DRV_CMD_ADDR, tcs_id, j, cmd->addr);
write_tcs_cmd(drv, RSC_DRV_CMD_DATA, tcs_id, j, cmd->data);
drivers: qcom: rpmh-rsc: Use rcuidle tracepoints for rpmh This tracepoint is hit now that we call into the rpmh code from the cpu idle path. Let's move this to be an rcuidle tracepoint so that we avoid the RCU idle splat below ============================= WARNING: suspicious RCU usage 5.4.10 #68 Tainted: G S ----------------------------- drivers/soc/qcom/trace-rpmh.h:72 suspicious rcu_dereference_check() usage! other info that might help us debug this: RCU used illegally from idle CPU! rcu_scheduler_active = 2, debug_locks = 1 RCU used illegally from extended quiescent state! 5 locks held by swapper/2/0: #0: ffffff81745d6ee8 (&(&genpd->slock)->rlock){+.+.}, at: genpd_lock_spin+0x1c/0x2c #1: ffffff81745da6e8 (&(&genpd->slock)->rlock/1){....}, at: genpd_lock_nested_spin+0x24/0x34 #2: ffffff8174f2ca20 (&(&genpd->slock)->rlock/2){....}, at: genpd_lock_nested_spin+0x24/0x34 #3: ffffff8174f2c300 (&(&drv->client.cache_lock)->rlock){....}, at: rpmh_flush+0x48/0x24c #4: ffffff8174f2c150 (&(&tcs->lock)->rlock){+.+.}, at: rpmh_rsc_write_ctrl_data+0x74/0x270 stack backtrace: CPU: 2 PID: 0 Comm: swapper/2 Tainted: G S 5.4.10 #68 Call trace: dump_backtrace+0x0/0x174 show_stack+0x20/0x2c dump_stack+0xc8/0x124 lockdep_rcu_suspicious+0xe4/0x104 __tcs_buffer_write+0x230/0x2d0 rpmh_rsc_write_ctrl_data+0x210/0x270 rpmh_flush+0x84/0x24c rpmh_domain_power_off+0x78/0x98 _genpd_power_off+0x40/0xc0 genpd_power_off+0x168/0x208 genpd_power_off+0x1e0/0x208 genpd_power_off+0x1e0/0x208 genpd_runtime_suspend+0x1ac/0x220 __rpm_callback+0x70/0xfc rpm_callback+0x34/0x8c rpm_suspend+0x218/0x4a4 __pm_runtime_suspend+0x88/0xac psci_enter_domain_idle_state+0x3c/0xb4 cpuidle_enter_state+0xb8/0x284 cpuidle_enter+0x38/0x4c call_cpuidle+0x3c/0x68 do_idle+0x194/0x260 cpu_startup_entry+0x24/0x28 secondary_start_kernel+0x150/0x15c Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Fixes: a65a397f2451 ("cpuidle: psci: Add support for PM domains by using genpd") Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200115013751.249588-1-swboyd@chromium.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-15 09:37:51 +08:00
trace_rpmh_send_msg_rcuidle(drv, tcs_id, j, msgid, cmd);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
}
write_tcs_reg(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, tcs_id, cmd_complete);
cmd_enable |= read_tcs_reg(drv, RSC_DRV_CMD_ENABLE, tcs_id);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
write_tcs_reg(drv, RSC_DRV_CMD_ENABLE, tcs_id, cmd_enable);
}
static int check_for_req_inflight(struct rsc_drv *drv, struct tcs_group *tcs,
const struct tcs_request *msg)
{
unsigned long curr_enabled;
u32 addr;
int i, j, k;
int tcs_id = tcs->offset;
for (i = 0; i < tcs->num_tcs; i++, tcs_id++) {
if (tcs_is_free(drv, tcs_id))
continue;
curr_enabled = read_tcs_reg(drv, RSC_DRV_CMD_ENABLE, tcs_id);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
for_each_set_bit(j, &curr_enabled, MAX_CMDS_PER_TCS) {
addr = read_tcs_cmd(drv, RSC_DRV_CMD_ADDR, tcs_id, j);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
for (k = 0; k < msg->num_cmds; k++) {
if (addr == msg->cmds[k].addr)
return -EBUSY;
}
}
}
return 0;
}
static int find_free_tcs(struct tcs_group *tcs)
{
int i;
for (i = 0; i < tcs->num_tcs; i++) {
if (tcs_is_free(tcs->drv, tcs->offset + i))
return tcs->offset + i;
}
return -EBUSY;
}
static int tcs_write(struct rsc_drv *drv, const struct tcs_request *msg)
{
struct tcs_group *tcs;
int tcs_id;
unsigned long flags;
int ret;
tcs = get_tcs_for_msg(drv, msg);
if (IS_ERR(tcs))
return PTR_ERR(tcs);
spin_lock_irqsave(&tcs->lock, flags);
spin_lock(&drv->lock);
/*
* The h/w does not like if we send a request to the same address,
* when one is already in-flight or being processed.
*/
ret = check_for_req_inflight(drv, tcs, msg);
if (ret) {
spin_unlock(&drv->lock);
goto done_write;
}
tcs_id = find_free_tcs(tcs);
if (tcs_id < 0) {
ret = tcs_id;
spin_unlock(&drv->lock);
goto done_write;
}
tcs->req[tcs_id - tcs->offset] = msg;
set_bit(tcs_id, drv->tcs_in_use);
if (msg->state == RPMH_ACTIVE_ONLY_STATE && tcs->type != ACTIVE_TCS) {
/*
* Clear previously programmed WAKE commands in selected
* repurposed TCS to avoid triggering them. tcs->slots will be
* cleaned from rpmh_flush() by invoking rpmh_rsc_invalidate()
*/
write_tcs_reg_sync(drv, RSC_DRV_CMD_ENABLE, tcs_id, 0);
write_tcs_reg_sync(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, tcs_id, 0);
enable_tcs_irq(drv, tcs_id, true);
}
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
spin_unlock(&drv->lock);
__tcs_buffer_write(drv, tcs_id, 0, msg);
__tcs_set_trigger(drv, tcs_id, true);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
done_write:
spin_unlock_irqrestore(&tcs->lock, flags);
return ret;
}
/**
* rpmh_rsc_send_data: Validate the incoming message and write to the
* appropriate TCS block.
*
* @drv: the controller
* @msg: the data to be sent
*
* Return: 0 on success, -EINVAL on error.
* Note: This call blocks until a valid data is written to the TCS.
*/
int rpmh_rsc_send_data(struct rsc_drv *drv, const struct tcs_request *msg)
{
int ret;
if (!msg || !msg->cmds || !msg->num_cmds ||
msg->num_cmds > MAX_RPMH_PAYLOAD) {
WARN_ON(1);
return -EINVAL;
}
do {
ret = tcs_write(drv, msg);
if (ret == -EBUSY) {
pr_info_ratelimited("TCS Busy, retrying RPMH message send: addr=%#x\n",
msg->cmds[0].addr);
udelay(10);
}
} while (ret == -EBUSY);
return ret;
}
static int find_match(const struct tcs_group *tcs, const struct tcs_cmd *cmd,
int len)
{
int i, j;
/* Check for already cached commands */
for_each_set_bit(i, tcs->slots, MAX_TCS_SLOTS) {
if (tcs->cmd_cache[i] != cmd[0].addr)
continue;
if (i + len >= tcs->num_tcs * tcs->ncpt)
goto seq_err;
for (j = 0; j < len; j++) {
if (tcs->cmd_cache[i + j] != cmd[j].addr)
goto seq_err;
}
return i;
}
return -ENODATA;
seq_err:
WARN(1, "Message does not match previous sequence.\n");
return -EINVAL;
}
static int find_slots(struct tcs_group *tcs, const struct tcs_request *msg,
int *tcs_id, int *cmd_id)
{
int slot, offset;
int i = 0;
/* Find if we already have the msg in our TCS */
slot = find_match(tcs, msg->cmds, msg->num_cmds);
if (slot >= 0)
goto copy_data;
/* Do over, until we can fit the full payload in a TCS */
do {
slot = bitmap_find_next_zero_area(tcs->slots, MAX_TCS_SLOTS,
i, msg->num_cmds, 0);
if (slot >= tcs->num_tcs * tcs->ncpt)
return -ENOMEM;
i += tcs->ncpt;
} while (slot + msg->num_cmds - 1 >= i);
copy_data:
bitmap_set(tcs->slots, slot, msg->num_cmds);
/* Copy the addresses of the resources over to the slots */
for (i = 0; i < msg->num_cmds; i++)
tcs->cmd_cache[slot + i] = msg->cmds[i].addr;
offset = slot / tcs->ncpt;
*tcs_id = offset + tcs->offset;
*cmd_id = slot % tcs->ncpt;
return 0;
}
static int tcs_ctrl_write(struct rsc_drv *drv, const struct tcs_request *msg)
{
struct tcs_group *tcs;
int tcs_id = 0, cmd_id = 0;
unsigned long flags;
int ret;
tcs = get_tcs_for_msg(drv, msg);
if (IS_ERR(tcs))
return PTR_ERR(tcs);
spin_lock_irqsave(&tcs->lock, flags);
/* find the TCS id and the command in the TCS to write to */
ret = find_slots(tcs, msg, &tcs_id, &cmd_id);
if (!ret)
__tcs_buffer_write(drv, tcs_id, cmd_id, msg);
spin_unlock_irqrestore(&tcs->lock, flags);
return ret;
}
/**
* rpmh_rsc_write_ctrl_data: Write request to the controller
*
* @drv: the controller
* @msg: the data to be written to the controller
*
* There is no response returned for writing the request to the controller.
*/
int rpmh_rsc_write_ctrl_data(struct rsc_drv *drv, const struct tcs_request *msg)
{
if (!msg || !msg->cmds || !msg->num_cmds ||
msg->num_cmds > MAX_RPMH_PAYLOAD) {
pr_err("Payload error\n");
return -EINVAL;
}
/* Data sent to this API will not be sent immediately */
if (msg->state == RPMH_ACTIVE_ONLY_STATE)
return -EINVAL;
return tcs_ctrl_write(drv, msg);
}
/**
* rpmh_rsc_ctrlr_is_busy() - Check if any of the AMCs are busy.
*
* @drv: The controller
*
* Checks if any of the AMCs are busy in handling ACTIVE sets.
* This is called from the last cpu powering down before flushing
* SLEEP and WAKE sets. If AMCs are busy, controller can not enter
* power collapse, so deny from the last cpu's pm notification.
*
* Return:
* * False - AMCs are idle
* * True - AMCs are busy
*/
static bool rpmh_rsc_ctrlr_is_busy(struct rsc_drv *drv)
{
int m;
struct tcs_group *tcs = get_tcs_of_type(drv, ACTIVE_TCS);
/*
* If we made an active request on a RSC that does not have a
* dedicated TCS for active state use, then re-purposed wake TCSes
* should be checked for not busy, because we used wake TCSes for
* active requests in this case.
*
* Since this is called from the last cpu, need not take drv or tcs
* lock before checking tcs_is_free().
*/
if (!tcs->num_tcs)
tcs = get_tcs_of_type(drv, WAKE_TCS);
for (m = tcs->offset; m < tcs->offset + tcs->num_tcs; m++) {
if (!tcs_is_free(drv, m))
return true;
}
return false;
}
static int rpmh_rsc_cpu_pm_callback(struct notifier_block *nfb,
unsigned long action, void *v)
{
struct rsc_drv *drv = container_of(nfb, struct rsc_drv, rsc_pm);
int ret = NOTIFY_OK;
spin_lock(&drv->pm_lock);
switch (action) {
case CPU_PM_ENTER:
cpumask_set_cpu(smp_processor_id(), &drv->cpus_entered_pm);
if (!cpumask_equal(&drv->cpus_entered_pm, cpu_online_mask))
goto exit;
break;
case CPU_PM_ENTER_FAILED:
case CPU_PM_EXIT:
cpumask_clear_cpu(smp_processor_id(), &drv->cpus_entered_pm);
goto exit;
}
ret = rpmh_rsc_ctrlr_is_busy(drv);
if (ret) {
ret = NOTIFY_BAD;
goto exit;
}
ret = rpmh_flush(&drv->client);
if (ret)
ret = NOTIFY_BAD;
else
ret = NOTIFY_OK;
exit:
spin_unlock(&drv->pm_lock);
return ret;
}
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
static int rpmh_probe_tcs_config(struct platform_device *pdev,
struct rsc_drv *drv, void __iomem *base)
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
{
struct tcs_type_config {
u32 type;
u32 n;
} tcs_cfg[TCS_TYPE_NR] = { { 0 } };
struct device_node *dn = pdev->dev.of_node;
u32 config, max_tcs, ncpt, offset;
int i, ret, n, st = 0;
struct tcs_group *tcs;
ret = of_property_read_u32(dn, "qcom,tcs-offset", &offset);
if (ret)
return ret;
drv->tcs_base = base + offset;
config = readl_relaxed(base + DRV_PRNT_CHLD_CONFIG);
max_tcs = config;
max_tcs &= DRV_NUM_TCS_MASK << (DRV_NUM_TCS_SHIFT * drv->id);
max_tcs = max_tcs >> (DRV_NUM_TCS_SHIFT * drv->id);
ncpt = config & (DRV_NCPT_MASK << DRV_NCPT_SHIFT);
ncpt = ncpt >> DRV_NCPT_SHIFT;
n = of_property_count_u32_elems(dn, "qcom,tcs-config");
if (n != 2 * TCS_TYPE_NR)
return -EINVAL;
for (i = 0; i < TCS_TYPE_NR; i++) {
ret = of_property_read_u32_index(dn, "qcom,tcs-config",
i * 2, &tcs_cfg[i].type);
if (ret)
return ret;
if (tcs_cfg[i].type >= TCS_TYPE_NR)
return -EINVAL;
ret = of_property_read_u32_index(dn, "qcom,tcs-config",
i * 2 + 1, &tcs_cfg[i].n);
if (ret)
return ret;
if (tcs_cfg[i].n > MAX_TCS_PER_TYPE)
return -EINVAL;
}
for (i = 0; i < TCS_TYPE_NR; i++) {
tcs = &drv->tcs[tcs_cfg[i].type];
if (tcs->drv)
return -EINVAL;
tcs->drv = drv;
tcs->type = tcs_cfg[i].type;
tcs->num_tcs = tcs_cfg[i].n;
tcs->ncpt = ncpt;
spin_lock_init(&tcs->lock);
if (!tcs->num_tcs || tcs->type == CONTROL_TCS)
continue;
if (st + tcs->num_tcs > max_tcs ||
st + tcs->num_tcs >= BITS_PER_BYTE * sizeof(tcs->mask))
return -EINVAL;
tcs->mask = ((1 << tcs->num_tcs) - 1) << st;
tcs->offset = st;
st += tcs->num_tcs;
/*
* Allocate memory to cache sleep and wake requests to
* avoid reading TCS register memory.
*/
if (tcs->type == ACTIVE_TCS)
continue;
tcs->cmd_cache = devm_kcalloc(&pdev->dev,
tcs->num_tcs * ncpt, sizeof(u32),
GFP_KERNEL);
if (!tcs->cmd_cache)
return -ENOMEM;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
}
drv->num_tcs = st;
return 0;
}
static int rpmh_rsc_probe(struct platform_device *pdev)
{
struct device_node *dn = pdev->dev.of_node;
struct rsc_drv *drv;
struct resource *res;
char drv_id[10] = {0};
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
int ret, irq;
u32 solver_config;
void __iomem *base;
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
/*
* Even though RPMh doesn't directly use cmd-db, all of its children
* do. To avoid adding this check to our children we'll do it now.
*/
ret = cmd_db_ready();
if (ret) {
if (ret != -EPROBE_DEFER)
dev_err(&pdev->dev, "Command DB not available (%d)\n",
ret);
return ret;
}
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
drv = devm_kzalloc(&pdev->dev, sizeof(*drv), GFP_KERNEL);
if (!drv)
return -ENOMEM;
ret = of_property_read_u32(dn, "qcom,drv-id", &drv->id);
if (ret)
return ret;
drv->name = of_get_property(dn, "label", NULL);
if (!drv->name)
drv->name = dev_name(&pdev->dev);
snprintf(drv_id, ARRAY_SIZE(drv_id), "drv-%d", drv->id);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, drv_id);
base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(base))
return PTR_ERR(base);
ret = rpmh_probe_tcs_config(pdev, drv, base);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
if (ret)
return ret;
spin_lock_init(&drv->lock);
bitmap_zero(drv->tcs_in_use, MAX_TCS_NR);
irq = platform_get_irq(pdev, drv->id);
if (irq < 0)
return irq;
ret = devm_request_irq(&pdev->dev, irq, tcs_tx_done,
IRQF_TRIGGER_HIGH | IRQF_NO_SUSPEND,
drv->name, drv);
if (ret)
return ret;
/*
* CPU PM notification are not required for controllers that support
* 'HW solver' mode where they can be in autonomous mode executing low
* power mode to power down.
*/
solver_config = readl_relaxed(base + DRV_SOLVER_CONFIG);
solver_config &= DRV_HW_SOLVER_MASK << DRV_HW_SOLVER_SHIFT;
solver_config = solver_config >> DRV_HW_SOLVER_SHIFT;
if (!solver_config) {
drv->rsc_pm.notifier_call = rpmh_rsc_cpu_pm_callback;
spin_lock_init(&drv->pm_lock);
cpu_pm_register_notifier(&drv->rsc_pm);
}
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
/* Enable the active TCS to send requests immediately */
write_tcs_reg(drv, RSC_DRV_IRQ_ENABLE, 0, drv->tcs[ACTIVE_TCS].mask);
spin_lock_init(&drv->client.cache_lock);
INIT_LIST_HEAD(&drv->client.cache);
INIT_LIST_HEAD(&drv->client.batch_cache);
dev_set_drvdata(&pdev->dev, drv);
drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2018-06-20 21:26:58 +08:00
return devm_of_platform_populate(&pdev->dev);
}
static const struct of_device_id rpmh_drv_match[] = {
{ .compatible = "qcom,rpmh-rsc", },
{ }
};
static struct platform_driver rpmh_driver = {
.probe = rpmh_rsc_probe,
.driver = {
.name = "rpmh",
.of_match_table = rpmh_drv_match,
},
};
static int __init rpmh_driver_init(void)
{
return platform_driver_register(&rpmh_driver);
}
arch_initcall(rpmh_driver_init);