linux/arch/arm/plat-omap/mcbsp.c

1080 lines
27 KiB
C
Raw Normal View History

/*
* linux/arch/arm/plat-omap/mcbsp.c
*
* Copyright (C) 2004 Nokia Corporation
* Author: Samuel Ortiz <samuel.ortiz@nokia.com>
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Multichannel mode not supported.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/wait.h>
#include <linux/completion.h>
#include <linux/interrupt.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <mach/dma.h>
#include <mach/mcbsp.h>
struct omap_mcbsp **mcbsp_ptr;
int omap_mcbsp_count;
void omap_mcbsp_write(void __iomem *io_base, u16 reg, u32 val)
{
if (cpu_class_is_omap1() || cpu_is_omap2420())
__raw_writew((u16)val, io_base + reg);
else
__raw_writel(val, io_base + reg);
}
int omap_mcbsp_read(void __iomem *io_base, u16 reg)
{
if (cpu_class_is_omap1() || cpu_is_omap2420())
return __raw_readw(io_base + reg);
else
return __raw_readl(io_base + reg);
}
#define OMAP_MCBSP_READ(base, reg) \
omap_mcbsp_read(base, OMAP_MCBSP_REG_##reg)
#define OMAP_MCBSP_WRITE(base, reg, val) \
omap_mcbsp_write(base, OMAP_MCBSP_REG_##reg, val)
#define omap_mcbsp_check_valid_id(id) (id < omap_mcbsp_count)
#define id_to_mcbsp_ptr(id) mcbsp_ptr[id];
static void omap_mcbsp_dump_reg(u8 id)
{
struct omap_mcbsp *mcbsp = id_to_mcbsp_ptr(id);
dev_dbg(mcbsp->dev, "**** McBSP%d regs ****\n", mcbsp->id);
dev_dbg(mcbsp->dev, "DRR2: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, DRR2));
dev_dbg(mcbsp->dev, "DRR1: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, DRR1));
dev_dbg(mcbsp->dev, "DXR2: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, DXR2));
dev_dbg(mcbsp->dev, "DXR1: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, DXR1));
dev_dbg(mcbsp->dev, "SPCR2: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, SPCR2));
dev_dbg(mcbsp->dev, "SPCR1: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, SPCR1));
dev_dbg(mcbsp->dev, "RCR2: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, RCR2));
dev_dbg(mcbsp->dev, "RCR1: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, RCR1));
dev_dbg(mcbsp->dev, "XCR2: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, XCR2));
dev_dbg(mcbsp->dev, "XCR1: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, XCR1));
dev_dbg(mcbsp->dev, "SRGR2: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, SRGR2));
dev_dbg(mcbsp->dev, "SRGR1: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, SRGR1));
dev_dbg(mcbsp->dev, "PCR0: 0x%04x\n",
OMAP_MCBSP_READ(mcbsp->io_base, PCR0));
dev_dbg(mcbsp->dev, "***********************\n");
}
static irqreturn_t omap_mcbsp_tx_irq_handler(int irq, void *dev_id)
{
struct omap_mcbsp *mcbsp_tx = dev_id;
u16 irqst_spcr2;
irqst_spcr2 = OMAP_MCBSP_READ(mcbsp_tx->io_base, SPCR2);
dev_dbg(mcbsp_tx->dev, "TX IRQ callback : 0x%x\n", irqst_spcr2);
if (irqst_spcr2 & XSYNC_ERR) {
dev_err(mcbsp_tx->dev, "TX Frame Sync Error! : 0x%x\n",
irqst_spcr2);
/* Writing zero to XSYNC_ERR clears the IRQ */
OMAP_MCBSP_WRITE(mcbsp_tx->io_base, SPCR2,
irqst_spcr2 & ~(XSYNC_ERR));
} else {
complete(&mcbsp_tx->tx_irq_completion);
}
return IRQ_HANDLED;
}
static irqreturn_t omap_mcbsp_rx_irq_handler(int irq, void *dev_id)
{
struct omap_mcbsp *mcbsp_rx = dev_id;
u16 irqst_spcr1;
irqst_spcr1 = OMAP_MCBSP_READ(mcbsp_rx->io_base, SPCR1);
dev_dbg(mcbsp_rx->dev, "RX IRQ callback : 0x%x\n", irqst_spcr1);
if (irqst_spcr1 & RSYNC_ERR) {
dev_err(mcbsp_rx->dev, "RX Frame Sync Error! : 0x%x\n",
irqst_spcr1);
/* Writing zero to RSYNC_ERR clears the IRQ */
OMAP_MCBSP_WRITE(mcbsp_rx->io_base, SPCR1,
irqst_spcr1 & ~(RSYNC_ERR));
} else {
complete(&mcbsp_rx->tx_irq_completion);
}
return IRQ_HANDLED;
}
static void omap_mcbsp_tx_dma_callback(int lch, u16 ch_status, void *data)
{
struct omap_mcbsp *mcbsp_dma_tx = data;
dev_dbg(mcbsp_dma_tx->dev, "TX DMA callback : 0x%x\n",
OMAP_MCBSP_READ(mcbsp_dma_tx->io_base, SPCR2));
/* We can free the channels */
omap_free_dma(mcbsp_dma_tx->dma_tx_lch);
mcbsp_dma_tx->dma_tx_lch = -1;
complete(&mcbsp_dma_tx->tx_dma_completion);
}
static void omap_mcbsp_rx_dma_callback(int lch, u16 ch_status, void *data)
{
struct omap_mcbsp *mcbsp_dma_rx = data;
dev_dbg(mcbsp_dma_rx->dev, "RX DMA callback : 0x%x\n",
OMAP_MCBSP_READ(mcbsp_dma_rx->io_base, SPCR2));
/* We can free the channels */
omap_free_dma(mcbsp_dma_rx->dma_rx_lch);
mcbsp_dma_rx->dma_rx_lch = -1;
complete(&mcbsp_dma_rx->rx_dma_completion);
}
/*
* omap_mcbsp_config simply write a config to the
* appropriate McBSP.
* You either call this function or set the McBSP registers
* by yourself before calling omap_mcbsp_start().
*/
void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg *config)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
dev_dbg(mcbsp->dev, "Configuring McBSP%d phys_base: 0x%08lx\n",
mcbsp->id, mcbsp->phys_base);
/* We write the given config */
OMAP_MCBSP_WRITE(io_base, SPCR2, config->spcr2);
OMAP_MCBSP_WRITE(io_base, SPCR1, config->spcr1);
OMAP_MCBSP_WRITE(io_base, RCR2, config->rcr2);
OMAP_MCBSP_WRITE(io_base, RCR1, config->rcr1);
OMAP_MCBSP_WRITE(io_base, XCR2, config->xcr2);
OMAP_MCBSP_WRITE(io_base, XCR1, config->xcr1);
OMAP_MCBSP_WRITE(io_base, SRGR2, config->srgr2);
OMAP_MCBSP_WRITE(io_base, SRGR1, config->srgr1);
OMAP_MCBSP_WRITE(io_base, MCR2, config->mcr2);
OMAP_MCBSP_WRITE(io_base, MCR1, config->mcr1);
OMAP_MCBSP_WRITE(io_base, PCR0, config->pcr0);
if (cpu_is_omap2430() || cpu_is_omap34xx()) {
OMAP_MCBSP_WRITE(io_base, XCCR, config->xccr);
OMAP_MCBSP_WRITE(io_base, RCCR, config->rccr);
}
}
EXPORT_SYMBOL(omap_mcbsp_config);
/*
* We can choose between IRQ based or polled IO.
* This needs to be called before omap_mcbsp_request().
*/
int omap_mcbsp_set_io_type(unsigned int id, omap_mcbsp_io_type_t io_type)
{
struct omap_mcbsp *mcbsp;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
spin_lock(&mcbsp->lock);
if (!mcbsp->free) {
dev_err(mcbsp->dev, "McBSP%d is currently in use\n",
mcbsp->id);
spin_unlock(&mcbsp->lock);
return -EINVAL;
}
mcbsp->io_type = io_type;
spin_unlock(&mcbsp->lock);
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_set_io_type);
int omap_mcbsp_request(unsigned int id)
{
struct omap_mcbsp *mcbsp;
int err;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
spin_lock(&mcbsp->lock);
if (!mcbsp->free) {
dev_err(mcbsp->dev, "McBSP%d is currently in use\n",
mcbsp->id);
spin_unlock(&mcbsp->lock);
return -EBUSY;
}
mcbsp->free = 0;
spin_unlock(&mcbsp->lock);
if (mcbsp->pdata && mcbsp->pdata->ops && mcbsp->pdata->ops->request)
mcbsp->pdata->ops->request(id);
clk_enable(mcbsp->iclk);
clk_enable(mcbsp->fclk);
/*
* Make sure that transmitter, receiver and sample-rate generator are
* not running before activating IRQs.
*/
OMAP_MCBSP_WRITE(mcbsp->io_base, SPCR1, 0);
OMAP_MCBSP_WRITE(mcbsp->io_base, SPCR2, 0);
if (mcbsp->io_type == OMAP_MCBSP_IRQ_IO) {
/* We need to get IRQs here */
init_completion(&mcbsp->tx_irq_completion);
err = request_irq(mcbsp->tx_irq, omap_mcbsp_tx_irq_handler,
0, "McBSP", (void *)mcbsp);
if (err != 0) {
dev_err(mcbsp->dev, "Unable to request TX IRQ %d "
"for McBSP%d\n", mcbsp->tx_irq,
mcbsp->id);
return err;
}
init_completion(&mcbsp->rx_irq_completion);
err = request_irq(mcbsp->rx_irq, omap_mcbsp_rx_irq_handler,
0, "McBSP", (void *)mcbsp);
if (err != 0) {
dev_err(mcbsp->dev, "Unable to request RX IRQ %d "
"for McBSP%d\n", mcbsp->rx_irq,
mcbsp->id);
free_irq(mcbsp->tx_irq, (void *)mcbsp);
return err;
}
}
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_request);
void omap_mcbsp_free(unsigned int id)
{
struct omap_mcbsp *mcbsp;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
if (mcbsp->pdata && mcbsp->pdata->ops && mcbsp->pdata->ops->free)
mcbsp->pdata->ops->free(id);
clk_disable(mcbsp->fclk);
clk_disable(mcbsp->iclk);
if (mcbsp->io_type == OMAP_MCBSP_IRQ_IO) {
/* Free IRQs */
free_irq(mcbsp->rx_irq, (void *)mcbsp);
free_irq(mcbsp->tx_irq, (void *)mcbsp);
}
spin_lock(&mcbsp->lock);
if (mcbsp->free) {
dev_err(mcbsp->dev, "McBSP%d was not reserved\n",
mcbsp->id);
spin_unlock(&mcbsp->lock);
return;
}
mcbsp->free = 1;
spin_unlock(&mcbsp->lock);
}
EXPORT_SYMBOL(omap_mcbsp_free);
/*
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
* Here we start the McBSP, by enabling transmitter, receiver or both.
* If no transmitter or receiver is active prior calling, then sample-rate
* generator and frame sync are started.
*/
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
void omap_mcbsp_start(unsigned int id, int tx, int rx)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
int idle;
u16 w;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
mcbsp->rx_word_length = (OMAP_MCBSP_READ(io_base, RCR1) >> 5) & 0x7;
mcbsp->tx_word_length = (OMAP_MCBSP_READ(io_base, XCR1) >> 5) & 0x7;
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
idle = !((OMAP_MCBSP_READ(io_base, SPCR2) |
OMAP_MCBSP_READ(io_base, SPCR1)) & 1);
if (idle) {
/* Start the sample generator */
w = OMAP_MCBSP_READ(io_base, SPCR2);
OMAP_MCBSP_WRITE(io_base, SPCR2, w | (1 << 6));
}
/* Enable transmitter and receiver */
w = OMAP_MCBSP_READ(io_base, SPCR2);
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
OMAP_MCBSP_WRITE(io_base, SPCR2, w | (tx & 1));
w = OMAP_MCBSP_READ(io_base, SPCR1);
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
OMAP_MCBSP_WRITE(io_base, SPCR1, w | (rx & 1));
/*
* Worst case: CLKSRG*2 = 8000khz: (1/8000) * 2 * 2 usec
* REVISIT: 100us may give enough time for two CLKSRG, however
* due to some unknown PM related, clock gating etc. reason it
* is now at 500us.
*/
udelay(500);
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
if (idle) {
/* Start frame sync */
w = OMAP_MCBSP_READ(io_base, SPCR2);
OMAP_MCBSP_WRITE(io_base, SPCR2, w | (1 << 7));
}
/* Dump McBSP Regs */
omap_mcbsp_dump_reg(id);
}
EXPORT_SYMBOL(omap_mcbsp_start);
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
void omap_mcbsp_stop(unsigned int id, int tx, int rx)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
int idle;
u16 w;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
/* Reset transmitter */
w = OMAP_MCBSP_READ(io_base, SPCR2);
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
OMAP_MCBSP_WRITE(io_base, SPCR2, w & ~(tx & 1));
/* Reset receiver */
w = OMAP_MCBSP_READ(io_base, SPCR1);
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
OMAP_MCBSP_WRITE(io_base, SPCR1, w & ~(rx & 1));
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 14:59:47 +08:00
idle = !((OMAP_MCBSP_READ(io_base, SPCR2) |
OMAP_MCBSP_READ(io_base, SPCR1)) & 1);
if (idle) {
/* Reset the sample rate generator */
w = OMAP_MCBSP_READ(io_base, SPCR2);
OMAP_MCBSP_WRITE(io_base, SPCR2, w & ~(1 << 6));
}
}
EXPORT_SYMBOL(omap_mcbsp_stop);
void omap_mcbsp_xmit_enable(unsigned int id, u8 enable)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
u16 w;
if (!(cpu_is_omap2430() || cpu_is_omap34xx()))
return;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
w = OMAP_MCBSP_READ(io_base, XCCR);
if (enable)
OMAP_MCBSP_WRITE(io_base, XCCR, w & ~(XDISABLE));
else
OMAP_MCBSP_WRITE(io_base, XCCR, w | XDISABLE);
}
EXPORT_SYMBOL(omap_mcbsp_xmit_enable);
void omap_mcbsp_recv_enable(unsigned int id, u8 enable)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
u16 w;
if (!(cpu_is_omap2430() || cpu_is_omap34xx()))
return;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
w = OMAP_MCBSP_READ(io_base, RCCR);
if (enable)
OMAP_MCBSP_WRITE(io_base, RCCR, w & ~(RDISABLE));
else
OMAP_MCBSP_WRITE(io_base, RCCR, w | RDISABLE);
}
EXPORT_SYMBOL(omap_mcbsp_recv_enable);
/* polled mcbsp i/o operations */
int omap_mcbsp_pollwrite(unsigned int id, u16 buf)
{
struct omap_mcbsp *mcbsp;
void __iomem *base;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
base = mcbsp->io_base;
writew(buf, base + OMAP_MCBSP_REG_DXR1);
/* if frame sync error - clear the error */
if (readw(base + OMAP_MCBSP_REG_SPCR2) & XSYNC_ERR) {
/* clear error */
writew(readw(base + OMAP_MCBSP_REG_SPCR2) & (~XSYNC_ERR),
base + OMAP_MCBSP_REG_SPCR2);
/* resend */
return -1;
} else {
/* wait for transmit confirmation */
int attemps = 0;
while (!(readw(base + OMAP_MCBSP_REG_SPCR2) & XRDY)) {
if (attemps++ > 1000) {
writew(readw(base + OMAP_MCBSP_REG_SPCR2) &
(~XRST),
base + OMAP_MCBSP_REG_SPCR2);
udelay(10);
writew(readw(base + OMAP_MCBSP_REG_SPCR2) |
(XRST),
base + OMAP_MCBSP_REG_SPCR2);
udelay(10);
dev_err(mcbsp->dev, "Could not write to"
" McBSP%d Register\n", mcbsp->id);
return -2;
}
}
}
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_pollwrite);
int omap_mcbsp_pollread(unsigned int id, u16 *buf)
{
struct omap_mcbsp *mcbsp;
void __iomem *base;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
base = mcbsp->io_base;
/* if frame sync error - clear the error */
if (readw(base + OMAP_MCBSP_REG_SPCR1) & RSYNC_ERR) {
/* clear error */
writew(readw(base + OMAP_MCBSP_REG_SPCR1) & (~RSYNC_ERR),
base + OMAP_MCBSP_REG_SPCR1);
/* resend */
return -1;
} else {
/* wait for recieve confirmation */
int attemps = 0;
while (!(readw(base + OMAP_MCBSP_REG_SPCR1) & RRDY)) {
if (attemps++ > 1000) {
writew(readw(base + OMAP_MCBSP_REG_SPCR1) &
(~RRST),
base + OMAP_MCBSP_REG_SPCR1);
udelay(10);
writew(readw(base + OMAP_MCBSP_REG_SPCR1) |
(RRST),
base + OMAP_MCBSP_REG_SPCR1);
udelay(10);
dev_err(mcbsp->dev, "Could not read from"
" McBSP%d Register\n", mcbsp->id);
return -2;
}
}
}
*buf = readw(base + OMAP_MCBSP_REG_DRR1);
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_pollread);
/*
* IRQ based word transmission.
*/
void omap_mcbsp_xmit_word(unsigned int id, u32 word)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
omap_mcbsp_word_length word_length;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
word_length = mcbsp->tx_word_length;
wait_for_completion(&mcbsp->tx_irq_completion);
if (word_length > OMAP_MCBSP_WORD_16)
OMAP_MCBSP_WRITE(io_base, DXR2, word >> 16);
OMAP_MCBSP_WRITE(io_base, DXR1, word & 0xffff);
}
EXPORT_SYMBOL(omap_mcbsp_xmit_word);
u32 omap_mcbsp_recv_word(unsigned int id)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
u16 word_lsb, word_msb = 0;
omap_mcbsp_word_length word_length;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
word_length = mcbsp->rx_word_length;
io_base = mcbsp->io_base;
wait_for_completion(&mcbsp->rx_irq_completion);
if (word_length > OMAP_MCBSP_WORD_16)
word_msb = OMAP_MCBSP_READ(io_base, DRR2);
word_lsb = OMAP_MCBSP_READ(io_base, DRR1);
return (word_lsb | (word_msb << 16));
}
EXPORT_SYMBOL(omap_mcbsp_recv_word);
int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word)
{
struct omap_mcbsp *mcbsp;
void __iomem *io_base;
omap_mcbsp_word_length tx_word_length;
omap_mcbsp_word_length rx_word_length;
u16 spcr2, spcr1, attempts = 0, word_lsb, word_msb = 0;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
tx_word_length = mcbsp->tx_word_length;
rx_word_length = mcbsp->rx_word_length;
if (tx_word_length != rx_word_length)
return -EINVAL;
/* First we wait for the transmitter to be ready */
spcr2 = OMAP_MCBSP_READ(io_base, SPCR2);
while (!(spcr2 & XRDY)) {
spcr2 = OMAP_MCBSP_READ(io_base, SPCR2);
if (attempts++ > 1000) {
/* We must reset the transmitter */
OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 & (~XRST));
udelay(10);
OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 | XRST);
udelay(10);
dev_err(mcbsp->dev, "McBSP%d transmitter not "
"ready\n", mcbsp->id);
return -EAGAIN;
}
}
/* Now we can push the data */
if (tx_word_length > OMAP_MCBSP_WORD_16)
OMAP_MCBSP_WRITE(io_base, DXR2, word >> 16);
OMAP_MCBSP_WRITE(io_base, DXR1, word & 0xffff);
/* We wait for the receiver to be ready */
spcr1 = OMAP_MCBSP_READ(io_base, SPCR1);
while (!(spcr1 & RRDY)) {
spcr1 = OMAP_MCBSP_READ(io_base, SPCR1);
if (attempts++ > 1000) {
/* We must reset the receiver */
OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 & (~RRST));
udelay(10);
OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 | RRST);
udelay(10);
dev_err(mcbsp->dev, "McBSP%d receiver not "
"ready\n", mcbsp->id);
return -EAGAIN;
}
}
/* Receiver is ready, let's read the dummy data */
if (rx_word_length > OMAP_MCBSP_WORD_16)
word_msb = OMAP_MCBSP_READ(io_base, DRR2);
word_lsb = OMAP_MCBSP_READ(io_base, DRR1);
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_spi_master_xmit_word_poll);
int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 *word)
{
struct omap_mcbsp *mcbsp;
u32 clock_word = 0;
void __iomem *io_base;
omap_mcbsp_word_length tx_word_length;
omap_mcbsp_word_length rx_word_length;
u16 spcr2, spcr1, attempts = 0, word_lsb, word_msb = 0;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
io_base = mcbsp->io_base;
tx_word_length = mcbsp->tx_word_length;
rx_word_length = mcbsp->rx_word_length;
if (tx_word_length != rx_word_length)
return -EINVAL;
/* First we wait for the transmitter to be ready */
spcr2 = OMAP_MCBSP_READ(io_base, SPCR2);
while (!(spcr2 & XRDY)) {
spcr2 = OMAP_MCBSP_READ(io_base, SPCR2);
if (attempts++ > 1000) {
/* We must reset the transmitter */
OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 & (~XRST));
udelay(10);
OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 | XRST);
udelay(10);
dev_err(mcbsp->dev, "McBSP%d transmitter not "
"ready\n", mcbsp->id);
return -EAGAIN;
}
}
/* We first need to enable the bus clock */
if (tx_word_length > OMAP_MCBSP_WORD_16)
OMAP_MCBSP_WRITE(io_base, DXR2, clock_word >> 16);
OMAP_MCBSP_WRITE(io_base, DXR1, clock_word & 0xffff);
/* We wait for the receiver to be ready */
spcr1 = OMAP_MCBSP_READ(io_base, SPCR1);
while (!(spcr1 & RRDY)) {
spcr1 = OMAP_MCBSP_READ(io_base, SPCR1);
if (attempts++ > 1000) {
/* We must reset the receiver */
OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 & (~RRST));
udelay(10);
OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 | RRST);
udelay(10);
dev_err(mcbsp->dev, "McBSP%d receiver not "
"ready\n", mcbsp->id);
return -EAGAIN;
}
}
/* Receiver is ready, there is something for us */
if (rx_word_length > OMAP_MCBSP_WORD_16)
word_msb = OMAP_MCBSP_READ(io_base, DRR2);
word_lsb = OMAP_MCBSP_READ(io_base, DRR1);
word[0] = (word_lsb | (word_msb << 16));
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_spi_master_recv_word_poll);
/*
* Simple DMA based buffer rx/tx routines.
* Nothing fancy, just a single buffer tx/rx through DMA.
* The DMA resources are released once the transfer is done.
* For anything fancier, you should use your own customized DMA
* routines and callbacks.
*/
int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer,
unsigned int length)
{
struct omap_mcbsp *mcbsp;
int dma_tx_ch;
int src_port = 0;
int dest_port = 0;
int sync_dev = 0;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
if (omap_request_dma(mcbsp->dma_tx_sync, "McBSP TX",
omap_mcbsp_tx_dma_callback,
mcbsp,
&dma_tx_ch)) {
dev_err(mcbsp->dev, " Unable to request DMA channel for "
"McBSP%d TX. Trying IRQ based TX\n",
mcbsp->id);
return -EAGAIN;
}
mcbsp->dma_tx_lch = dma_tx_ch;
dev_err(mcbsp->dev, "McBSP%d TX DMA on channel %d\n", mcbsp->id,
dma_tx_ch);
init_completion(&mcbsp->tx_dma_completion);
if (cpu_class_is_omap1()) {
src_port = OMAP_DMA_PORT_TIPB;
dest_port = OMAP_DMA_PORT_EMIFF;
}
if (cpu_class_is_omap2())
sync_dev = mcbsp->dma_tx_sync;
omap_set_dma_transfer_params(mcbsp->dma_tx_lch,
OMAP_DMA_DATA_TYPE_S16,
length >> 1, 1,
OMAP_DMA_SYNC_ELEMENT,
sync_dev, 0);
omap_set_dma_dest_params(mcbsp->dma_tx_lch,
src_port,
OMAP_DMA_AMODE_CONSTANT,
mcbsp->phys_base + OMAP_MCBSP_REG_DXR1,
0, 0);
omap_set_dma_src_params(mcbsp->dma_tx_lch,
dest_port,
OMAP_DMA_AMODE_POST_INC,
buffer,
0, 0);
omap_start_dma(mcbsp->dma_tx_lch);
wait_for_completion(&mcbsp->tx_dma_completion);
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_xmit_buffer);
int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer,
unsigned int length)
{
struct omap_mcbsp *mcbsp;
int dma_rx_ch;
int src_port = 0;
int dest_port = 0;
int sync_dev = 0;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return -ENODEV;
}
mcbsp = id_to_mcbsp_ptr(id);
if (omap_request_dma(mcbsp->dma_rx_sync, "McBSP RX",
omap_mcbsp_rx_dma_callback,
mcbsp,
&dma_rx_ch)) {
dev_err(mcbsp->dev, "Unable to request DMA channel for "
"McBSP%d RX. Trying IRQ based RX\n",
mcbsp->id);
return -EAGAIN;
}
mcbsp->dma_rx_lch = dma_rx_ch;
dev_err(mcbsp->dev, "McBSP%d RX DMA on channel %d\n", mcbsp->id,
dma_rx_ch);
init_completion(&mcbsp->rx_dma_completion);
if (cpu_class_is_omap1()) {
src_port = OMAP_DMA_PORT_TIPB;
dest_port = OMAP_DMA_PORT_EMIFF;
}
if (cpu_class_is_omap2())
sync_dev = mcbsp->dma_rx_sync;
omap_set_dma_transfer_params(mcbsp->dma_rx_lch,
OMAP_DMA_DATA_TYPE_S16,
length >> 1, 1,
OMAP_DMA_SYNC_ELEMENT,
sync_dev, 0);
omap_set_dma_src_params(mcbsp->dma_rx_lch,
src_port,
OMAP_DMA_AMODE_CONSTANT,
mcbsp->phys_base + OMAP_MCBSP_REG_DRR1,
0, 0);
omap_set_dma_dest_params(mcbsp->dma_rx_lch,
dest_port,
OMAP_DMA_AMODE_POST_INC,
buffer,
0, 0);
omap_start_dma(mcbsp->dma_rx_lch);
wait_for_completion(&mcbsp->rx_dma_completion);
return 0;
}
EXPORT_SYMBOL(omap_mcbsp_recv_buffer);
/*
* SPI wrapper.
* Since SPI setup is much simpler than the generic McBSP one,
* this wrapper just need an omap_mcbsp_spi_cfg structure as an input.
* Once this is done, you can call omap_mcbsp_start().
*/
void omap_mcbsp_set_spi_mode(unsigned int id,
const struct omap_mcbsp_spi_cfg *spi_cfg)
{
struct omap_mcbsp *mcbsp;
struct omap_mcbsp_reg_cfg mcbsp_cfg;
if (!omap_mcbsp_check_valid_id(id)) {
printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
return;
}
mcbsp = id_to_mcbsp_ptr(id);
memset(&mcbsp_cfg, 0, sizeof(struct omap_mcbsp_reg_cfg));
/* SPI has only one frame */
mcbsp_cfg.rcr1 |= (RWDLEN1(spi_cfg->word_length) | RFRLEN1(0));
mcbsp_cfg.xcr1 |= (XWDLEN1(spi_cfg->word_length) | XFRLEN1(0));
/* Clock stop mode */
if (spi_cfg->clk_stp_mode == OMAP_MCBSP_CLK_STP_MODE_NO_DELAY)
mcbsp_cfg.spcr1 |= (1 << 12);
else
mcbsp_cfg.spcr1 |= (3 << 11);
/* Set clock parities */
if (spi_cfg->rx_clock_polarity == OMAP_MCBSP_CLK_RISING)
mcbsp_cfg.pcr0 |= CLKRP;
else
mcbsp_cfg.pcr0 &= ~CLKRP;
if (spi_cfg->tx_clock_polarity == OMAP_MCBSP_CLK_RISING)
mcbsp_cfg.pcr0 &= ~CLKXP;
else
mcbsp_cfg.pcr0 |= CLKXP;
/* Set SCLKME to 0 and CLKSM to 1 */
mcbsp_cfg.pcr0 &= ~SCLKME;
mcbsp_cfg.srgr2 |= CLKSM;
/* Set FSXP */
if (spi_cfg->fsx_polarity == OMAP_MCBSP_FS_ACTIVE_HIGH)
mcbsp_cfg.pcr0 &= ~FSXP;
else
mcbsp_cfg.pcr0 |= FSXP;
if (spi_cfg->spi_mode == OMAP_MCBSP_SPI_MASTER) {
mcbsp_cfg.pcr0 |= CLKXM;
mcbsp_cfg.srgr1 |= CLKGDV(spi_cfg->clk_div - 1);
mcbsp_cfg.pcr0 |= FSXM;
mcbsp_cfg.srgr2 &= ~FSGM;
mcbsp_cfg.xcr2 |= XDATDLY(1);
mcbsp_cfg.rcr2 |= RDATDLY(1);
} else {
mcbsp_cfg.pcr0 &= ~CLKXM;
mcbsp_cfg.srgr1 |= CLKGDV(1);
mcbsp_cfg.pcr0 &= ~FSXM;
mcbsp_cfg.xcr2 &= ~XDATDLY(3);
mcbsp_cfg.rcr2 &= ~RDATDLY(3);
}
mcbsp_cfg.xcr2 &= ~XPHASE;
mcbsp_cfg.rcr2 &= ~RPHASE;
omap_mcbsp_config(id, &mcbsp_cfg);
}
EXPORT_SYMBOL(omap_mcbsp_set_spi_mode);
/*
* McBSP1 and McBSP3 are directly mapped on 1610 and 1510.
* 730 has only 2 McBSP, and both of them are MPU peripherals.
*/
static int __devinit omap_mcbsp_probe(struct platform_device *pdev)
{
struct omap_mcbsp_platform_data *pdata = pdev->dev.platform_data;
struct omap_mcbsp *mcbsp;
int id = pdev->id - 1;
int ret = 0;
if (!pdata) {
dev_err(&pdev->dev, "McBSP device initialized without"
"platform data\n");
ret = -EINVAL;
goto exit;
}
dev_dbg(&pdev->dev, "Initializing OMAP McBSP (%d).\n", pdev->id);
if (id >= omap_mcbsp_count) {
dev_err(&pdev->dev, "Invalid McBSP device id (%d)\n", id);
ret = -EINVAL;
goto exit;
}
mcbsp = kzalloc(sizeof(struct omap_mcbsp), GFP_KERNEL);
if (!mcbsp) {
ret = -ENOMEM;
goto exit;
}
spin_lock_init(&mcbsp->lock);
mcbsp->id = id + 1;
mcbsp->free = 1;
mcbsp->dma_tx_lch = -1;
mcbsp->dma_rx_lch = -1;
mcbsp->phys_base = pdata->phys_base;
mcbsp->io_base = ioremap(pdata->phys_base, SZ_4K);
if (!mcbsp->io_base) {
ret = -ENOMEM;
goto err_ioremap;
}
/* Default I/O is IRQ based */
mcbsp->io_type = OMAP_MCBSP_IRQ_IO;
mcbsp->tx_irq = pdata->tx_irq;
mcbsp->rx_irq = pdata->rx_irq;
mcbsp->dma_rx_sync = pdata->dma_rx_sync;
mcbsp->dma_tx_sync = pdata->dma_tx_sync;
mcbsp->iclk = clk_get(&pdev->dev, "ick");
if (IS_ERR(mcbsp->iclk)) {
ret = PTR_ERR(mcbsp->iclk);
dev_err(&pdev->dev, "unable to get ick: %d\n", ret);
goto err_iclk;
}
mcbsp->fclk = clk_get(&pdev->dev, "fck");
if (IS_ERR(mcbsp->fclk)) {
ret = PTR_ERR(mcbsp->fclk);
dev_err(&pdev->dev, "unable to get fck: %d\n", ret);
goto err_fclk;
}
mcbsp->pdata = pdata;
mcbsp->dev = &pdev->dev;
mcbsp_ptr[id] = mcbsp;
platform_set_drvdata(pdev, mcbsp);
return 0;
err_fclk:
clk_put(mcbsp->iclk);
err_iclk:
iounmap(mcbsp->io_base);
err_ioremap:
kfree(mcbsp);
exit:
return ret;
}
static int __devexit omap_mcbsp_remove(struct platform_device *pdev)
{
struct omap_mcbsp *mcbsp = platform_get_drvdata(pdev);
platform_set_drvdata(pdev, NULL);
if (mcbsp) {
if (mcbsp->pdata && mcbsp->pdata->ops &&
mcbsp->pdata->ops->free)
mcbsp->pdata->ops->free(mcbsp->id);
clk_disable(mcbsp->fclk);
clk_disable(mcbsp->iclk);
clk_put(mcbsp->fclk);
clk_put(mcbsp->iclk);
iounmap(mcbsp->io_base);
mcbsp->fclk = NULL;
mcbsp->iclk = NULL;
mcbsp->free = 0;
mcbsp->dev = NULL;
}
return 0;
}
static struct platform_driver omap_mcbsp_driver = {
.probe = omap_mcbsp_probe,
.remove = __devexit_p(omap_mcbsp_remove),
.driver = {
.name = "omap-mcbsp",
},
};
int __init omap_mcbsp_init(void)
{
/* Register the McBSP driver */
return platform_driver_register(&omap_mcbsp_driver);
}