linux/arch/mips/loongson/loongson-3/Makefile

#
# Makefile for Loongson-3 family machines
#
obj-y			+= irq.o

obj-$(CONFIG_SMP)	+= smp.o
MIPS: Loongson 3: Add IRQ init and dispatch support IRQ routing path of Loongson-3: Devices(most) --> I8259 --> HT Controller --> IRQ Routing Table --> CPU ^ \| Device(legacy devices such as UART) --> Bonito ---\| IRQ Routing Table route 32 INTs to CPU's INT0~INT3(IP2~IP5 of CP0), 32 INTs include 16 HT INTs(mostly), 4 PCI INTs, 1 LPC INT, etc. IP6 is used for IPI and IP7 is used for internal MIPS timer. LOONGSON_INT_ROUTER_* are IRQ Routing Table registers. I8259 IRQs are 1:1 mapped to HT1 INTs. LOONGSON_HT1_* are configuration registers of HT1 controller. Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Hongliang Tao <taohl@lemote.com> Signed-off-by: Hua Yan <yanh@lemote.com> Tested-by: Alex Smith <alex.smith@imgtec.com> Reviewed-by: Alex Smith <alex.smith@imgtec.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Patchwork: https://patchwork.linux-mips.org/patch/6634 Signed-off-by: Ralf Baechle <ralf@linux-mips.org> 2014-03-21 18:44:04 +08:00			`#`
			`# Makefile for Loongson-3 family machines`
			`#`
			`obj-y += irq.o`
MIPS: Loongson 3: Add Loongson-3 SMP support IPI registers of Loongson-3 include IPI_SET, IPI_CLEAR, IPI_STATUS, IPI_EN and IPI_MAILBOX_BUF. Each bit of IPI_STATUS indicate a type of IPI and IPI_EN indicate whether the IPI is enabled. The sender write 1 to IPI_SET bits generate IPIs in IPI_STATUS, and receiver write 1 to bits of IPI_CLEAR to clear IPIs. IPI_MAILBOX_BUF are used to deliver more information about IPIs. Why we change code in arch/mips/loongson/common/setup.c? If without this change, when SMP configured, system cannot boot since it hang at printk() in cgroup_init_early(). The root cause is: console_trylock() \-->down_trylock(&console_sem) \-->raw_spin_unlock_irqrestore(&sem->lock, flags) \-->_raw_spin_unlock_irqrestore()(SMP/UP have different versions) \-->__raw_spin_unlock_irqrestore() (following is the SMP case) \-->do_raw_spin_unlock() \-->arch_spin_unlock() \-->nudge_writes() \-->mb() \-->wbflush() \-->__wbflush() In previous code __wbflush() is initialized in plat_mem_setup(), but cgroup_init_early() is called before plat_mem_setup(). Therefore, In this patch we make changes to avoid boot failure. Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Hongliang Tao <taohl@lemote.com> Signed-off-by: Hua Yan <yanh@lemote.com> Tested-by: Alex Smith <alex.smith@imgtec.com> Reviewed-by: Alex Smith <alex.smith@imgtec.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Patchwork: https://patchwork.linux-mips.org/patch/6638 Signed-off-by: Ralf Baechle <ralf@linux-mips.org> 2014-03-21 18:44:08 +08:00
			`obj-$(CONFIG_SMP) += smp.o`