linux/drivers/gpu/drm/meson/meson_vclk.c

774 lines
22 KiB
C
Raw Normal View History

drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
/*
* Copyright (C) 2016 BayLibre, SAS
* Author: Neil Armstrong <narmstrong@baylibre.com>
* Copyright (C) 2015 Amlogic, Inc. All rights reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <drm/drmP.h>
#include "meson_drv.h"
#include "meson_vclk.h"
/**
* DOC: Video Clocks
*
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
* VCLK is the "Pixel Clock" frequency generator from a dedicated PLL.
* We handle the following encodings :
*
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
* - CVBS 27MHz generator via the VCLK2 to the VENCI and VDAC blocks
* - HDMI Pixel Clocks generation
*
* What is missing :
*
* - Genenate Pixel clocks for 2K/4K 10bit formats
*
* Clock generator scheme :
*
* .. code::
*
* __________ _________ _____
* | | | | | |--ENCI
* | HDMI PLL |-| PLL_DIV |--- VCLK--| |--ENCL
* |__________| |_________| \ | MUX |--ENCP
* --VCLK2-| |--VDAC
* |_____|--HDMI-TX
*
* Final clocks can take input for either VCLK or VCLK2, but
* VCLK is the preferred path for HDMI clocking and VCLK2 is the
* preferred path for CVBS VDAC clocking.
*
* VCLK and VCLK2 have fixed divided clocks paths for /1, /2, /4, /6 or /12.
*
* The PLL_DIV can achieve an additional fractional dividing like
* 1.5, 3.5, 3.75... to generate special 2K and 4K 10bit clocks.
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
*/
/* HHI Registers */
#define HHI_VID_PLL_CLK_DIV 0x1a0 /* 0x68 offset in data sheet */
#define VID_PLL_EN BIT(19)
#define VID_PLL_BYPASS BIT(18)
#define VID_PLL_PRESET BIT(15)
#define HHI_VIID_CLK_DIV 0x128 /* 0x4a offset in data sheet */
#define VCLK2_DIV_MASK 0xff
#define VCLK2_DIV_EN BIT(16)
#define VCLK2_DIV_RESET BIT(17)
#define CTS_VDAC_SEL_MASK (0xf << 28)
#define CTS_VDAC_SEL_SHIFT 28
#define HHI_VIID_CLK_CNTL 0x12c /* 0x4b offset in data sheet */
#define VCLK2_EN BIT(19)
#define VCLK2_SEL_MASK (0x7 << 16)
#define VCLK2_SEL_SHIFT 16
#define VCLK2_SOFT_RESET BIT(15)
#define VCLK2_DIV1_EN BIT(0)
#define HHI_VID_CLK_DIV 0x164 /* 0x59 offset in data sheet */
#define VCLK_DIV_MASK 0xff
#define VCLK_DIV_EN BIT(16)
#define VCLK_DIV_RESET BIT(17)
#define CTS_ENCP_SEL_MASK (0xf << 24)
#define CTS_ENCP_SEL_SHIFT 24
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
#define CTS_ENCI_SEL_MASK (0xf << 28)
#define CTS_ENCI_SEL_SHIFT 28
#define HHI_VID_CLK_CNTL 0x17c /* 0x5f offset in data sheet */
#define VCLK_EN BIT(19)
#define VCLK_SEL_MASK (0x7 << 16)
#define VCLK_SEL_SHIFT 16
#define VCLK_SOFT_RESET BIT(15)
#define VCLK_DIV1_EN BIT(0)
#define VCLK_DIV2_EN BIT(1)
#define VCLK_DIV4_EN BIT(2)
#define VCLK_DIV6_EN BIT(3)
#define VCLK_DIV12_EN BIT(4)
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
#define HHI_VID_CLK_CNTL2 0x194 /* 0x65 offset in data sheet */
#define CTS_ENCI_EN BIT(0)
#define CTS_ENCP_EN BIT(2)
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
#define CTS_VDAC_EN BIT(4)
#define HDMI_TX_PIXEL_EN BIT(5)
#define HHI_HDMI_CLK_CNTL 0x1cc /* 0x73 offset in data sheet */
#define HDMI_TX_PIXEL_SEL_MASK (0xf << 16)
#define HDMI_TX_PIXEL_SEL_SHIFT 16
#define CTS_HDMI_SYS_SEL_MASK (0x7 << 9)
#define CTS_HDMI_SYS_DIV_MASK (0x7f)
#define CTS_HDMI_SYS_EN BIT(8)
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
#define HHI_VDAC_CNTL0 0x2F4 /* 0xbd offset in data sheet */
#define HHI_VDAC_CNTL1 0x2F8 /* 0xbe offset in data sheet */
#define HHI_HDMI_PLL_CNTL 0x320 /* 0xc8 offset in data sheet */
#define HHI_HDMI_PLL_CNTL2 0x324 /* 0xc9 offset in data sheet */
#define HHI_HDMI_PLL_CNTL3 0x328 /* 0xca offset in data sheet */
#define HHI_HDMI_PLL_CNTL4 0x32C /* 0xcb offset in data sheet */
#define HHI_HDMI_PLL_CNTL5 0x330 /* 0xcc offset in data sheet */
#define HHI_HDMI_PLL_CNTL6 0x334 /* 0xcd offset in data sheet */
#define HDMI_PLL_RESET BIT(28)
#define HDMI_PLL_LOCK BIT(31)
/* VID PLL Dividers */
enum {
VID_PLL_DIV_1 = 0,
VID_PLL_DIV_2,
VID_PLL_DIV_2p5,
VID_PLL_DIV_3,
VID_PLL_DIV_3p5,
VID_PLL_DIV_3p75,
VID_PLL_DIV_4,
VID_PLL_DIV_5,
VID_PLL_DIV_6,
VID_PLL_DIV_6p25,
VID_PLL_DIV_7,
VID_PLL_DIV_7p5,
VID_PLL_DIV_12,
VID_PLL_DIV_14,
VID_PLL_DIV_15,
};
void meson_vid_pll_set(struct meson_drm *priv, unsigned int div)
{
unsigned int shift_val = 0;
unsigned int shift_sel = 0;
/* Disable vid_pll output clock */
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV, VID_PLL_EN, 0);
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV, VID_PLL_PRESET, 0);
switch (div) {
case VID_PLL_DIV_2:
shift_val = 0x0aaa;
shift_sel = 0;
break;
case VID_PLL_DIV_2p5:
shift_val = 0x5294;
shift_sel = 2;
break;
case VID_PLL_DIV_3:
shift_val = 0x0db6;
shift_sel = 0;
break;
case VID_PLL_DIV_3p5:
shift_val = 0x36cc;
shift_sel = 1;
break;
case VID_PLL_DIV_3p75:
shift_val = 0x6666;
shift_sel = 2;
break;
case VID_PLL_DIV_4:
shift_val = 0x0ccc;
shift_sel = 0;
break;
case VID_PLL_DIV_5:
shift_val = 0x739c;
shift_sel = 2;
break;
case VID_PLL_DIV_6:
shift_val = 0x0e38;
shift_sel = 0;
break;
case VID_PLL_DIV_6p25:
shift_val = 0x0000;
shift_sel = 3;
break;
case VID_PLL_DIV_7:
shift_val = 0x3c78;
shift_sel = 1;
break;
case VID_PLL_DIV_7p5:
shift_val = 0x78f0;
shift_sel = 2;
break;
case VID_PLL_DIV_12:
shift_val = 0x0fc0;
shift_sel = 0;
break;
case VID_PLL_DIV_14:
shift_val = 0x3f80;
shift_sel = 1;
break;
case VID_PLL_DIV_15:
shift_val = 0x7f80;
shift_sel = 2;
break;
}
if (div == VID_PLL_DIV_1)
/* Enable vid_pll bypass to HDMI pll */
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
VID_PLL_BYPASS, VID_PLL_BYPASS);
else {
/* Disable Bypass */
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
VID_PLL_BYPASS, 0);
/* Clear sel */
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
3 << 16, 0);
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
VID_PLL_PRESET, 0);
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
0x7fff, 0);
/* Setup sel and val */
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
3 << 16, shift_sel << 16);
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
VID_PLL_PRESET, VID_PLL_PRESET);
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
0x7fff, shift_val);
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
VID_PLL_PRESET, 0);
}
/* Enable the vid_pll output clock */
regmap_update_bits(priv->hhi, HHI_VID_PLL_CLK_DIV,
VID_PLL_EN, VID_PLL_EN);
}
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
/*
* Setup VCLK2 for 27MHz, and enable clocks for ENCI and VDAC
*
* TOFIX: Refactor into table to also handle HDMI frequency and paths
*/
static void meson_venci_cvbs_clock_config(struct meson_drm *priv)
{
unsigned int val;
/* Setup PLL to output 1.485GHz */
if (meson_vpu_is_compatible(priv, "amlogic,meson-gxbb-vpu")) {
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x5800023d);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL2, 0x00404e00);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0x0d5c5091);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x801da72c);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x71486980);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x00000e55);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x4800023d);
} else if (meson_vpu_is_compatible(priv, "amlogic,meson-gxm-vpu") ||
meson_vpu_is_compatible(priv, "amlogic,meson-gxl-vpu")) {
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x4000027b);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL2, 0x800cb300);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0xa6212844);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x0c4d000c);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x001fa729);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x01a31500);
/* Reset PLL */
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL,
HDMI_PLL_RESET, HDMI_PLL_RESET);
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL,
HDMI_PLL_RESET, 0);
}
/* Poll for lock bit */
regmap_read_poll_timeout(priv->hhi, HHI_HDMI_PLL_CNTL, val,
(val & HDMI_PLL_LOCK), 10, 0);
/* Disable VCLK2 */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_CNTL, VCLK2_EN, 0);
/* Setup vid_pll to /1 */
meson_vid_pll_set(priv, VID_PLL_DIV_1);
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
/* Setup the VCLK2 divider value to achieve 27MHz */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_DIV,
VCLK2_DIV_MASK, (55 - 1));
/* select vid_pll for vclk2 */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_CNTL,
VCLK2_SEL_MASK, (4 << VCLK2_SEL_SHIFT));
/* enable vclk2 gate */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_CNTL, VCLK2_EN, VCLK2_EN);
/* select vclk_div1 for enci */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCI_SEL_MASK, (8 << CTS_ENCI_SEL_SHIFT));
/* select vclk_div1 for vdac */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_DIV,
CTS_VDAC_SEL_MASK, (8 << CTS_VDAC_SEL_SHIFT));
/* release vclk2_div_reset and enable vclk2_div */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_DIV,
VCLK2_DIV_EN | VCLK2_DIV_RESET, VCLK2_DIV_EN);
/* enable vclk2_div1 gate */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_CNTL,
VCLK2_DIV1_EN, VCLK2_DIV1_EN);
/* reset vclk2 */
regmap_update_bits(priv->hhi, HHI_VIID_CLK_CNTL,
VCLK2_SOFT_RESET, VCLK2_SOFT_RESET);
regmap_update_bits(priv->hhi, HHI_VIID_CLK_CNTL,
VCLK2_SOFT_RESET, 0);
/* enable enci_clk */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL2,
CTS_ENCI_EN, CTS_ENCI_EN);
/* enable vdac_clk */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL2,
CTS_VDAC_EN, CTS_VDAC_EN);
}
/* PLL O1 O2 O3 VP DV EN TX */
/* 4320 /4 /4 /1 /5 /1 => /2 /2 */
#define MESON_VCLK_HDMI_ENCI_54000 1
/* 4320 /4 /4 /1 /5 /1 => /1 /2 */
#define MESON_VCLK_HDMI_DDR_54000 2
/* 2970 /4 /1 /1 /5 /1 => /1 /2 */
#define MESON_VCLK_HDMI_DDR_148500 3
/* 2970 /2 /2 /2 /5 /1 => /1 /1 */
#define MESON_VCLK_HDMI_74250 4
/* 2970 /1 /2 /2 /5 /1 => /1 /1 */
#define MESON_VCLK_HDMI_148500 5
/* 2970 /1 /1 /1 /5 /2 => /1 /1 */
#define MESON_VCLK_HDMI_297000 6
/* 5940 /1 /1 /2 /5 /1 => /1 /1 */
#define MESON_VCLK_HDMI_594000 7
struct meson_vclk_params {
unsigned int pll_base_freq;
unsigned int pll_od1;
unsigned int pll_od2;
unsigned int pll_od3;
unsigned int vid_pll_div;
unsigned int vclk_div;
} params[] = {
[MESON_VCLK_HDMI_ENCI_54000] = {
.pll_base_freq = 4320000,
.pll_od1 = 4,
.pll_od2 = 4,
.pll_od3 = 1,
.vid_pll_div = VID_PLL_DIV_5,
.vclk_div = 1,
},
[MESON_VCLK_HDMI_DDR_54000] = {
.pll_base_freq = 4320000,
.pll_od1 = 4,
.pll_od2 = 4,
.pll_od3 = 1,
.vid_pll_div = VID_PLL_DIV_5,
.vclk_div = 1,
},
[MESON_VCLK_HDMI_DDR_148500] = {
.pll_base_freq = 2970000,
.pll_od1 = 4,
.pll_od2 = 1,
.pll_od3 = 1,
.vid_pll_div = VID_PLL_DIV_5,
.vclk_div = 1,
},
[MESON_VCLK_HDMI_74250] = {
.pll_base_freq = 2970000,
.pll_od1 = 2,
.pll_od2 = 2,
.pll_od3 = 2,
.vid_pll_div = VID_PLL_DIV_5,
.vclk_div = 1,
},
[MESON_VCLK_HDMI_148500] = {
.pll_base_freq = 2970000,
.pll_od1 = 1,
.pll_od2 = 2,
.pll_od3 = 2,
.vid_pll_div = VID_PLL_DIV_5,
.vclk_div = 1,
},
[MESON_VCLK_HDMI_297000] = {
.pll_base_freq = 2970000,
.pll_od1 = 1,
.pll_od2 = 1,
.pll_od3 = 1,
.vid_pll_div = VID_PLL_DIV_5,
.vclk_div = 2,
},
[MESON_VCLK_HDMI_594000] = {
.pll_base_freq = 5940000,
.pll_od1 = 1,
.pll_od2 = 1,
.pll_od3 = 2,
.vid_pll_div = VID_PLL_DIV_5,
.vclk_div = 1,
},
};
static inline unsigned int pll_od_to_reg(unsigned int od)
{
switch (od) {
case 1:
return 0;
case 2:
return 1;
case 4:
return 2;
case 8:
return 3;
}
/* Invalid */
return 0;
}
void meson_hdmi_pll_set(struct meson_drm *priv,
unsigned int base,
unsigned int od1,
unsigned int od2,
unsigned int od3)
{
unsigned int val;
if (meson_vpu_is_compatible(priv, "amlogic,meson-gxbb-vpu")) {
switch (base) {
case 2970000:
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x5800023d);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL2, 0x00000000);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0x0d5c5091);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x801da72c);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x71486980);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x00000e55);
/* Enable and unreset */
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL,
0x7 << 28, 0x4 << 28);
/* Poll for lock bit */
regmap_read_poll_timeout(priv->hhi, HHI_HDMI_PLL_CNTL,
val, (val & HDMI_PLL_LOCK), 10, 0);
/* div_frac */
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL2,
0xFFFF, 0x4e00);
break;
case 4320000:
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x5800025a);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL2, 0x00000000);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0x0d5c5091);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x801da72c);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x71486980);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x00000e55);
/* unreset */
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL,
BIT(28), 0);
/* Poll for lock bit */
regmap_read_poll_timeout(priv->hhi, HHI_HDMI_PLL_CNTL,
val, (val & HDMI_PLL_LOCK), 10, 0);
break;
case 5940000:
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x5800027b);
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL2,
0xFFFF, 0x4c00);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0x135c5091);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x801da72c);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x71486980);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x00000e55);
/* unreset */
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL,
BIT(28), 0);
/* Poll for lock bit */
regmap_read_poll_timeout(priv->hhi, HHI_HDMI_PLL_CNTL,
val, (val & HDMI_PLL_LOCK), 10, 0);
break;
};
} else if (meson_vpu_is_compatible(priv, "amlogic,meson-gxm-vpu") ||
meson_vpu_is_compatible(priv, "amlogic,meson-gxl-vpu")) {
switch (base) {
case 2970000:
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x4000027b);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL2, 0x800cb300);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0x860f30c4);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x0c8e0000);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x001fa729);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x01a31500);
break;
case 4320000:
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x400002b4);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL2, 0x800cb000);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0x860f30c4);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x0c8e0000);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x001fa729);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x01a31500);
break;
case 5940000:
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL, 0x400002f7);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL2, 0x800cb200);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL3, 0x860f30c4);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL4, 0x0c8e0000);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL5, 0x001fa729);
regmap_write(priv->hhi, HHI_HDMI_PLL_CNTL6, 0x01a31500);
break;
};
/* Reset PLL */
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL,
HDMI_PLL_RESET, HDMI_PLL_RESET);
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL,
HDMI_PLL_RESET, 0);
/* Poll for lock bit */
regmap_read_poll_timeout(priv->hhi, HHI_HDMI_PLL_CNTL, val,
(val & HDMI_PLL_LOCK), 10, 0);
};
if (meson_vpu_is_compatible(priv, "amlogic,meson-gxbb-vpu"))
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL2,
3 << 16, pll_od_to_reg(od1) << 16);
else if (meson_vpu_is_compatible(priv, "amlogic,meson-gxm-vpu") ||
meson_vpu_is_compatible(priv, "amlogic,meson-gxl-vpu"))
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL3,
3 << 21, pll_od_to_reg(od1) << 21);
if (meson_vpu_is_compatible(priv, "amlogic,meson-gxbb-vpu"))
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL2,
3 << 22, pll_od_to_reg(od2) << 22);
else if (meson_vpu_is_compatible(priv, "amlogic,meson-gxm-vpu") ||
meson_vpu_is_compatible(priv, "amlogic,meson-gxl-vpu"))
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL3,
3 << 23, pll_od_to_reg(od2) << 23);
if (meson_vpu_is_compatible(priv, "amlogic,meson-gxbb-vpu"))
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL2,
3 << 18, pll_od_to_reg(od3) << 18);
else if (meson_vpu_is_compatible(priv, "amlogic,meson-gxm-vpu") ||
meson_vpu_is_compatible(priv, "amlogic,meson-gxl-vpu"))
regmap_update_bits(priv->hhi, HHI_HDMI_PLL_CNTL3,
3 << 19, pll_od_to_reg(od3) << 19);
}
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
void meson_vclk_setup(struct meson_drm *priv, unsigned int target,
unsigned int vclk_freq, unsigned int venc_freq,
unsigned int dac_freq, bool hdmi_use_enci)
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
{
unsigned int freq;
unsigned int hdmi_tx_div;
unsigned int venc_div;
if (target == MESON_VCLK_TARGET_CVBS) {
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
meson_venci_cvbs_clock_config(priv);
return;
}
hdmi_tx_div = vclk_freq / dac_freq;
if (hdmi_tx_div == 0) {
pr_err("Fatal Error, invalid HDMI-TX freq %d\n",
dac_freq);
return;
}
venc_div = vclk_freq / venc_freq;
if (venc_div == 0) {
pr_err("Fatal Error, invalid HDMI venc freq %d\n",
venc_freq);
return;
}
switch (vclk_freq) {
case 54000:
if (hdmi_use_enci)
freq = MESON_VCLK_HDMI_ENCI_54000;
else
freq = MESON_VCLK_HDMI_DDR_54000;
break;
case 74250:
freq = MESON_VCLK_HDMI_74250;
break;
case 148500:
if (dac_freq != 148500)
freq = MESON_VCLK_HDMI_DDR_148500;
else
freq = MESON_VCLK_HDMI_148500;
break;
case 297000:
freq = MESON_VCLK_HDMI_297000;
break;
case 594000:
freq = MESON_VCLK_HDMI_594000;
break;
default:
pr_err("Fatal Error, invalid HDMI vclk freq %d\n",
vclk_freq);
return;
}
/* Set HDMI-TX sys clock */
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
CTS_HDMI_SYS_SEL_MASK, 0);
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
CTS_HDMI_SYS_DIV_MASK, 0);
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
CTS_HDMI_SYS_EN, CTS_HDMI_SYS_EN);
/* Set HDMI PLL rate */
meson_hdmi_pll_set(priv, params[freq].pll_base_freq,
params[freq].pll_od1,
params[freq].pll_od2,
params[freq].pll_od3);
/* Setup vid_pll divider */
meson_vid_pll_set(priv, params[freq].vid_pll_div);
/* Set VCLK div */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_SEL_MASK, 0);
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
VCLK_DIV_MASK, params[freq].vclk_div - 1);
/* Set HDMI-TX source */
switch (hdmi_tx_div) {
case 1:
/* enable vclk_div1 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV1_EN, VCLK_DIV1_EN);
/* select vclk_div1 for HDMI-TX */
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
HDMI_TX_PIXEL_SEL_MASK, 0);
break;
case 2:
/* enable vclk_div2 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV2_EN, VCLK_DIV2_EN);
/* select vclk_div2 for HDMI-TX */
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
HDMI_TX_PIXEL_SEL_MASK, 1 << HDMI_TX_PIXEL_SEL_SHIFT);
break;
case 4:
/* enable vclk_div4 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV4_EN, VCLK_DIV4_EN);
/* select vclk_div4 for HDMI-TX */
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
HDMI_TX_PIXEL_SEL_MASK, 2 << HDMI_TX_PIXEL_SEL_SHIFT);
break;
case 6:
/* enable vclk_div6 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV6_EN, VCLK_DIV6_EN);
/* select vclk_div6 for HDMI-TX */
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
HDMI_TX_PIXEL_SEL_MASK, 3 << HDMI_TX_PIXEL_SEL_SHIFT);
break;
case 12:
/* enable vclk_div12 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV12_EN, VCLK_DIV12_EN);
/* select vclk_div12 for HDMI-TX */
regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL,
HDMI_TX_PIXEL_SEL_MASK, 4 << HDMI_TX_PIXEL_SEL_SHIFT);
break;
}
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL2,
HDMI_TX_PIXEL_EN, HDMI_TX_PIXEL_EN);
/* Set ENCI/ENCP Source */
switch (venc_div) {
case 1:
/* enable vclk_div1 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV1_EN, VCLK_DIV1_EN);
if (hdmi_use_enci)
/* select vclk_div1 for enci */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCI_SEL_MASK, 0);
else
/* select vclk_div1 for encp */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCP_SEL_MASK, 0);
break;
case 2:
/* enable vclk_div2 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV2_EN, VCLK_DIV2_EN);
if (hdmi_use_enci)
/* select vclk_div2 for enci */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCI_SEL_MASK, 1 << CTS_ENCI_SEL_SHIFT);
else
/* select vclk_div2 for encp */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCP_SEL_MASK, 1 << CTS_ENCP_SEL_SHIFT);
break;
case 4:
/* enable vclk_div4 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV4_EN, VCLK_DIV4_EN);
if (hdmi_use_enci)
/* select vclk_div4 for enci */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCI_SEL_MASK, 2 << CTS_ENCI_SEL_SHIFT);
else
/* select vclk_div4 for encp */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCP_SEL_MASK, 2 << CTS_ENCP_SEL_SHIFT);
break;
case 6:
/* enable vclk_div6 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV6_EN, VCLK_DIV6_EN);
if (hdmi_use_enci)
/* select vclk_div6 for enci */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCI_SEL_MASK, 3 << CTS_ENCI_SEL_SHIFT);
else
/* select vclk_div6 for encp */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCP_SEL_MASK, 3 << CTS_ENCP_SEL_SHIFT);
break;
case 12:
/* enable vclk_div12 gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL,
VCLK_DIV12_EN, VCLK_DIV12_EN);
if (hdmi_use_enci)
/* select vclk_div12 for enci */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCI_SEL_MASK, 4 << CTS_ENCI_SEL_SHIFT);
else
/* select vclk_div12 for encp */
regmap_update_bits(priv->hhi, HHI_VID_CLK_DIV,
CTS_ENCP_SEL_MASK, 4 << CTS_ENCP_SEL_SHIFT);
break;
}
if (hdmi_use_enci)
/* Enable ENCI clock gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL2,
CTS_ENCI_EN, CTS_ENCI_EN);
else
/* Enable ENCP clock gate */
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL2,
CTS_ENCP_EN, CTS_ENCP_EN);
regmap_update_bits(priv->hhi, HHI_VID_CLK_CNTL, VCLK_EN, VCLK_EN);
drm: Add support for Amlogic Meson Graphic Controller The Amlogic Meson Display controller is composed of several components : DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| | vd1 _______ _____________ _________________ | | D |-------| |----| | | | | HDMI PLL | D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | R |-------| |----| Processing | | | | | | osd2 | | | |---| Enci ----------|----|-----VDAC------| R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| A | osd1 | | | Blenders | | Encl ----------|----|---------------| M |-------|______|----|____________| |________________| | | ___|__________________________________________________________|_______________| VIU: Video Input Unit --------------------- The Video Input Unit is in charge of the pixel scanout from the DDR memory. It fetches the frames addresses, stride and parameters from the "Canvas" memory. This part is also in charge of the CSC (Colorspace Conversion). It can handle 2 OSD Planes and 2 Video Planes. VPP: Video Post Processing -------------------------- The Video Post Processing is in charge of the scaling and blending of the various planes into a single pixel stream. There is a special "pre-blending" used by the video planes with a dedicated scaler and a "post-blending" to merge with the OSD Planes. The OSD planes also have a dedicated scaler for one of the OSD. VENC: Video Encoders -------------------- The VENC is composed of the multiple pixel encoders : - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - ENCP : Progressive Video Encoder for HDMI - ENCL : LCD LVDS Encoder The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock tree and provides the scanout clock to the VPP and VIU. The ENCI is connected to a single VDAC for Composite Output. The ENCI and ENCP are connected to an on-chip HDMI Transceiver. This driver is a DRM/KMS driver using the following DRM components : - GEM-CMA - PRIME-CMA - Atomic Modesetting - FBDev-CMA For the following SoCs : - GXBB Family (S905) - GXL Family (S905X, S905D) - GXM Family (S912) The current driver only supports the CVBS PAL/NTSC output modes, but the CRTC/Planes management should support bigger modes. But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in a second time. The Device Tree bindings makes use of the endpoints video interface definitions to connect to the optional CVBS and in the future the HDMI Connector nodes. HDMI Support is planned for a next release. Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2016-11-10 22:29:37 +08:00
}
EXPORT_SYMBOL_GPL(meson_vclk_setup);