openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
linux/arch/sh/include/mach-sdk7786/mach/fpga.h

156 lines
4.0 KiB
C
Raw Normal View History

sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#ifndef __MACH_SDK7786_FPGA_H
#define __MACH_SDK7786_FPGA_H
#include <linux/io.h>
#include <linux/types.h>
#include <linux/bitops.h>
#define SRSTR 0x000
sh: mach-sdk7786: Probe system FPGA area mapping. This implements dynamic probing for the system FPGA. The system reset controller contains a fixed magic read word in order to identify the FPGA. This just utilizes a simple loop that scans across all of the fixed physical areas (area 0 through area 6) to locate the FPGA. The FPGA also contains register information detailing the area mappings and chip select settings for all of the other blocks, so this needs to be done before we can set up anything else. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 17:25:19 +08:00
#define SRSTR_MAGIC 0x1971 /* Fixed magical read value */
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define INTASR 0x010
#define INTAMR 0x020
#define MODSWR 0x030
#define INTTESTR 0x040
#define SYSSR 0x050
#define NRGPR 0x060
sh: mach-sdk7786: Handle baseboard NMI source selection. The on-board NMI switch is routed through and mangled by the FPGA prior to its delivery to the NMI pin, so add some glue for the various configuration options. The default is to unmask it and enable all input sources. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-12-17 17:58:04 +08:00
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define NMISR 0x070
sh: mach-sdk7786: Handle baseboard NMI source selection. The on-board NMI switch is routed through and mangled by the FPGA prior to its delivery to the NMI pin, so add some glue for the various configuration options. The default is to unmask it and enable all input sources. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-12-17 17:58:04 +08:00
#define NMISR_MAN_NMI BIT(0)
#define NMISR_AUX_NMI BIT(1)
#define NMISR_MASK (NMISR_MAN_NMI | NMISR_AUX_NMI)
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define NMIMR 0x080
#define NMIMR_MAN_NMIM BIT(0) /* Manual NMI mask */
#define NMIMR_AUX_NMIM BIT(1) /* Auxiliary NMI mask */
sh: mach-sdk7786: Handle baseboard NMI source selection. The on-board NMI switch is routed through and mangled by the FPGA prior to its delivery to the NMI pin, so add some glue for the various configuration options. The default is to unmask it and enable all input sources. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-12-17 17:58:04 +08:00
#define NMIMR_MASK (NMIMR_MAN_NMIM | NMIMR_AUX_NMIM)
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define INTBSR 0x090
#define INTBMR 0x0a0
#define USRLEDR 0x0b0
#define MAPSWR 0x0c0
#define FPGAVR 0x0d0
#define FPGADR 0x0e0
#define PCBRR 0x0f0
#define RSR 0x100
#define EXTASR 0x110
#define SPCAR 0x120
#define INTMSR 0x130
sh: pci: Support slot 4 routing on SDK7786. SDK7786 supports connecting either slot3 or 4 to the same PCIe port by way of FPGA muxing. By default the vertical slot 3 on the baseboard is enabled, so this adds in a command line option for forcibly enabling the slot 4 edge connector. If nothing has been specified on the command line, we fall back to reading the resistor values for card presence to figure out where to route the port to. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-14 06:37:01 +08:00
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define PCIECR 0x140
sh: pci: Support slot 4 routing on SDK7786. SDK7786 supports connecting either slot3 or 4 to the same PCIe port by way of FPGA muxing. By default the vertical slot 3 on the baseboard is enabled, so this adds in a command line option for forcibly enabling the slot 4 edge connector. If nothing has been specified on the command line, we fall back to reading the resistor values for card presence to figure out where to route the port to. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-14 06:37:01 +08:00
#define PCIECR_PCIEMUX1 BIT(15)
#define PCIECR_PCIEMUX0 BIT(14)
#define PCIECR_PRST4 BIT(12) /* slot 4 card present */
#define PCIECR_PRST3 BIT(11) /* slot 3 card present */
#define PCIECR_PRST2 BIT(10) /* slot 2 card present */
#define PCIECR_PRST1 BIT(9) /* slot 1 card present */
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786. The SDK7786 FPGA has secondary control over the PCIe clocks, specifically relating to the slots and oscillator. This ties the FPGA clocks in to the clock framework and balances the refcounting similar to how the primary on-chip clocks are managed. While the on-chip clocks are per-port, the FPGA clock enable/disable is global for the entire block. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-14 07:44:55 +08:00
#define PCIECR_CLKEN BIT(4) /* oscillator enable */
sh: pci: Support slot 4 routing on SDK7786. SDK7786 supports connecting either slot3 or 4 to the same PCIe port by way of FPGA muxing. By default the vertical slot 3 on the baseboard is enabled, so this adds in a command line option for forcibly enabling the slot 4 edge connector. If nothing has been specified on the command line, we fall back to reading the resistor values for card presence to figure out where to route the port to. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-14 06:37:01 +08:00
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define FAER 0x150
#define USRGPIR 0x160
sh: mach-sdk7786: Add support for the FPGA SRAM. This ties in the 2KiB of FPGA SRAM in to the generic SRAM pool. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-15 01:13:04 +08:00
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
/* 0x170 reserved */
sh: mach-sdk7786: Add support for the FPGA SRAM. This ties in the 2KiB of FPGA SRAM in to the generic SRAM pool. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-10-15 01:13:04 +08:00
#define LCLASR 0x180
#define LCLASR_FRAMEN BIT(15)
#define LCLASR_FPGA_SEL_SHIFT 12
#define LCLASR_NAND_SEL_SHIFT 8
#define LCLASR_NORB_SEL_SHIFT 4
#define LCLASR_NORA_SEL_SHIFT 0
#define LCLASR_AREA_MASK 0x7
#define LCLASR_FPGA_SEL_MASK (LCLASR_AREA_MASK << LCLASR_FPGA_SEL_SHIFT)
#define LCLASR_NAND_SEL_MASK (LCLASR_AREA_MASK << LCLASR_NAND_SEL_SHIFT)
#define LCLASR_NORB_SEL_MASK (LCLASR_AREA_MASK << LCLASR_NORB_SEL_SHIFT)
#define LCLASR_NORA_SEL_MASK (LCLASR_AREA_MASK << LCLASR_NORA_SEL_SHIFT)
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define SBCR 0x190
#define SCBR_I2CMEN BIT(0) /* FPGA I2C master enable */
#define SCBR_I2CCEN BIT(1) /* CPU I2C master enable */
#define PWRCR 0x1a0
sh: mach-sdk7786: pm_power_off support. This wires up power-off support for the SDK7786 board. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-04-19 15:27:47 +08:00
#define PWRCR_SCISEL0 BIT(0)
#define PWRCR_SCISEL1 BIT(1)
#define PWRCR_SCIEN BIT(2) /* Serial port enable */
#define PWRCR_PDWNACK BIT(5) /* Power down acknowledge */
#define PWRCR_PDWNREQ BIT(7) /* Power down request */
#define PWRCR_INT2 BIT(11) /* INT2 connection to power manager */
#define PWRCR_BUPINIT BIT(13) /* DDR backup initialize */
#define PWRCR_BKPRST BIT(15) /* Backup power reset */
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define SPCBR 0x1b0
#define SPICR 0x1c0
#define SPIDR 0x1d0
#define I2CCR 0x1e0
#define I2CDR 0x1f0
#define FPGACR 0x200
#define IASELR1 0x210
#define IASELR2 0x220
#define IASELR3 0x230
#define IASELR4 0x240
#define IASELR5 0x250
#define IASELR6 0x260
#define IASELR7 0x270
#define IASELR8 0x280
#define IASELR9 0x290
#define IASELR10 0x2a0
#define IASELR11 0x2b0
#define IASELR12 0x2c0
#define IASELR13 0x2d0
#define IASELR14 0x2e0
#define IASELR15 0x2f0
/* 0x300 reserved */
#define IBSELR1 0x310
#define IBSELR2 0x320
#define IBSELR3 0x330
#define IBSELR4 0x340
#define IBSELR5 0x350
#define IBSELR6 0x360
#define IBSELR7 0x370
#define IBSELR8 0x380
#define IBSELR9 0x390
#define IBSELR10 0x3a0
#define IBSELR11 0x3b0
#define IBSELR12 0x3c0
#define IBSELR13 0x3d0
#define IBSELR14 0x3e0
#define IBSELR15 0x3f0
#define USRACR 0x400
#define BEEPR 0x410
#define USRLCDR 0x420
#define SMBCR 0x430
#define SMBDR 0x440
#define USBCR 0x450
#define AMSR 0x460
#define ACCR 0x470
#define SDIFCR 0x480
/* arch/sh/boards/mach-sdk7786/fpga.c */
extern void __iomem *sdk7786_fpga_base;
extern void sdk7786_fpga_init(void);
sh: mach-sdk7786: Handle baseboard NMI source selection. The on-board NMI switch is routed through and mangled by the FPGA prior to its delivery to the NMI pin, so add some glue for the various configuration options. The default is to unmask it and enable all input sources. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-12-17 17:58:04 +08:00
/* arch/sh/boards/mach-sdk7786/nmi.c */
extern void sdk7786_nmi_init(void);
sh: mach-sdk7786: FPGA updates. This does a bit of refactoring of the FPGA management code. The primary FPGA initialization is moved out to its own file in preparation for implementing some of the more complex capabilities, a complete set of register definitions is provided, and all of the existing users in the board code are moved over to use the new interface instead of setting up overlapping mappings. This also corrects the FPGA size, which previously was chomped off at the SDIF control register. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-20 14:08:36 +08:00
#define SDK7786_FPGA_REGADDR(reg) (sdk7786_fpga_base + (reg))
/*
* A convenience wrapper from register offset to internal I2C address,
* when the FPGA is in I2C slave mode.
*/
#define SDK7786_FPGA_I2CADDR(reg) ((reg) >> 3)
static inline u16 fpga_read_reg(unsigned int reg)
{
return ioread16(sdk7786_fpga_base + reg);
}
static inline void fpga_write_reg(u16 val, unsigned int reg)
{
iowrite16(val, sdk7786_fpga_base + reg);
}
#endif /* __MACH_SDK7786_FPGA_H */