linux/drivers/usb/host/ehci-hub.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2001-2004 by David Brownell
 */

/* this file is part of ehci-hcd.c */

/*-------------------------------------------------------------------------*/

/*
 * EHCI Root Hub ... the nonsharable stuff
 *
 * Registers don't need cpu_to_le32, that happens transparently
 */

/*-------------------------------------------------------------------------*/
#include <linux/usb/otg.h>

#define	PORT_WAKE_BITS	(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)

#ifdef	CONFIG_PM

static void unlink_empty_async_suspended(struct ehci_hcd *ehci);

static int persist_enabled_on_companion(struct usb_device *udev, void *unused)
{
	return !udev->maxchild && udev->persist_enabled &&
		udev->bus->root_hub->speed < USB_SPEED_HIGH;
}

/* After a power loss, ports that were owned by the companion must be
 * reset so that the companion can still own them.
 */
static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
{
	u32 __iomem	*reg;
	u32		status;
	int		port;
	__le32		buf;
	struct usb_hcd	*hcd = ehci_to_hcd(ehci);

	if (!ehci->owned_ports)
		return;

	/*
	 * USB 1.1 devices are mostly HIDs, which don't need to persist across
	 * suspends. If we ensure that none of our companion's devices have
	 * persist_enabled (by looking through all USB 1.1 buses in the system),
	 * we can skip this and avoid slowing resume down. Devices without
	 * persist will just get reenumerated shortly after resume anyway.
	 */
	if (!usb_for_each_dev(NULL, persist_enabled_on_companion))
		return;

	/* Make sure the ports are powered */
	port = HCS_N_PORTS(ehci->hcs_params);
	while (port--) {
		if (test_bit(port, &ehci->owned_ports)) {
			reg = &ehci->regs->port_status[port];
			status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
			if (!(status & PORT_POWER))
				ehci_port_power(ehci, port, true);
		}
	}

	/* Give the connections some time to appear */
	msleep(20);

	spin_lock_irq(&ehci->lock);
	port = HCS_N_PORTS(ehci->hcs_params);
	while (port--) {
		if (test_bit(port, &ehci->owned_ports)) {
			reg = &ehci->regs->port_status[port];
			status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;

			/* Port already owned by companion? */
			if (status & PORT_OWNER)
				clear_bit(port, &ehci->owned_ports);
			else if (test_bit(port, &ehci->companion_ports))
				ehci_writel(ehci, status & ~PORT_PE, reg);
			else {
				spin_unlock_irq(&ehci->lock);
				ehci_hub_control(hcd, SetPortFeature,
						USB_PORT_FEAT_RESET, port + 1,
						NULL, 0);
				spin_lock_irq(&ehci->lock);
			}
		}
	}
	spin_unlock_irq(&ehci->lock);

	if (!ehci->owned_ports)
		return;
	msleep(90);		/* Wait for resets to complete */

	spin_lock_irq(&ehci->lock);
	port = HCS_N_PORTS(ehci->hcs_params);
	while (port--) {
		if (test_bit(port, &ehci->owned_ports)) {
			spin_unlock_irq(&ehci->lock);
			ehci_hub_control(hcd, GetPortStatus,
					0, port + 1,
					(char *) &buf, sizeof(buf));
			spin_lock_irq(&ehci->lock);

			/* The companion should now own the port,
			 * but if something went wrong the port must not
			 * remain enabled.
			 */
			reg = &ehci->regs->port_status[port];
			status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
			if (status & PORT_OWNER)
				ehci_writel(ehci, status | PORT_CSC, reg);
			else {
				ehci_dbg(ehci, "failed handover port %d: %x\n",
						port + 1, status);
				ehci_writel(ehci, status & ~PORT_PE, reg);
			}
		}
	}

	ehci->owned_ports = 0;
	spin_unlock_irq(&ehci->lock);
}

static int ehci_port_change(struct ehci_hcd *ehci)
{
	int i = HCS_N_PORTS(ehci->hcs_params);

	/* First check if the controller indicates a change event */

	if (ehci_readl(ehci, &ehci->regs->status) & STS_PCD)
		return 1;

	/*
	 * Not all controllers appear to update this while going from D3 to D0,
	 * so check the individual port status registers as well
	 */

	while (i--)
		if (ehci_readl(ehci, &ehci->regs->port_status[i]) & PORT_CSC)
			return 1;

	return 0;
}

void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
		bool suspending, bool do_wakeup)
{
	int		port;
	u32		temp;

	/* If remote wakeup is enabled for the root hub but disabled
	 * for the controller, we must adjust all the port wakeup flags
	 * when the controller is suspended or resumed.  In all other
	 * cases they don't need to be changed.
	 */
	if (!ehci_to_hcd(ehci)->self.root_hub->do_remote_wakeup || do_wakeup)
		return;

	spin_lock_irq(&ehci->lock);

	/* clear phy low-power mode before changing wakeup flags */
	if (ehci->has_tdi_phy_lpm) {
		port = HCS_N_PORTS(ehci->hcs_params);
		while (port--) {
			u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[port];

			temp = ehci_readl(ehci, hostpc_reg);
			ehci_writel(ehci, temp & ~HOSTPC_PHCD, hostpc_reg);
		}
		spin_unlock_irq(&ehci->lock);
		msleep(5);
		spin_lock_irq(&ehci->lock);
	}

	port = HCS_N_PORTS(ehci->hcs_params);
	while (port--) {
		u32 __iomem	*reg = &ehci->regs->port_status[port];
		u32		t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
		u32		t2 = t1 & ~PORT_WAKE_BITS;

		/* If we are suspending the controller, clear the flags.
		 * If we are resuming the controller, set the wakeup flags.
		 */
		if (!suspending) {
			if (t1 & PORT_CONNECT)
				t2 |= PORT_WKOC_E | PORT_WKDISC_E;
			else
				t2 |= PORT_WKOC_E | PORT_WKCONN_E;
		}
		ehci_writel(ehci, t2, reg);
	}

	/* enter phy low-power mode again */
	if (ehci->has_tdi_phy_lpm) {
		port = HCS_N_PORTS(ehci->hcs_params);
		while (port--) {
			u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[port];

			temp = ehci_readl(ehci, hostpc_reg);
			ehci_writel(ehci, temp | HOSTPC_PHCD, hostpc_reg);
		}
	}

	/* Does the root hub have a port wakeup pending? */
	if (!suspending && ehci_port_change(ehci))
		usb_hcd_resume_root_hub(ehci_to_hcd(ehci));

	spin_unlock_irq(&ehci->lock);
}
EXPORT_SYMBOL_GPL(ehci_adjust_port_wakeup_flags);

static int ehci_bus_suspend (struct usb_hcd *hcd)
{
	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
	int			port;
	int			mask;
	int			changed;
	bool			fs_idle_delay;

	ehci_dbg(ehci, "suspend root hub\n");

	if (time_before (jiffies, ehci->next_statechange))
		msleep(5);

	/* stop the schedules */
	ehci_quiesce(ehci);

	spin_lock_irq (&ehci->lock);
	if (ehci->rh_state < EHCI_RH_RUNNING)
		goto done;

	/* Once the controller is stopped, port resumes that are already
	 * in progress won't complete.  Hence if remote wakeup is enabled
	 * for the root hub and any ports are in the middle of a resume or
	 * remote wakeup, we must fail the suspend.
	 */
	if (hcd->self.root_hub->do_remote_wakeup) {
		if (ehci->resuming_ports) {
			spin_unlock_irq(&ehci->lock);
			ehci_dbg(ehci, "suspend failed because a port is resuming\n");
			return -EBUSY;
		}
	}

	/* Unlike other USB host controller types, EHCI doesn't have
	 * any notion of "global" or bus-wide suspend.  The driver has
	 * to manually suspend all the active unsuspended ports, and
	 * then manually resume them in the bus_resume() routine.
	 */
	ehci->bus_suspended = 0;
	ehci->owned_ports = 0;
	changed = 0;
	fs_idle_delay = false;
	port = HCS_N_PORTS(ehci->hcs_params);
	while (port--) {
		u32 __iomem	*reg = &ehci->regs->port_status [port];
		u32		t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
		u32		t2 = t1 & ~PORT_WAKE_BITS;

		/* keep track of which ports we suspend */
		if (t1 & PORT_OWNER)
			set_bit(port, &ehci->owned_ports);
		else if ((t1 & PORT_PE) && !(t1 & PORT_SUSPEND)) {
			t2 |= PORT_SUSPEND;
			set_bit(port, &ehci->bus_suspended);
		}

		/* enable remote wakeup on all ports, if told to do so */
		if (hcd->self.root_hub->do_remote_wakeup) {
			/* only enable appropriate wake bits, otherwise the
			 * hardware can not go phy low power mode. If a race
			 * condition happens here(connection change during bits
			 * set), the port change detection will finally fix it.
			 */
			if (t1 & PORT_CONNECT)
				t2 |= PORT_WKOC_E | PORT_WKDISC_E;
			else
				t2 |= PORT_WKOC_E | PORT_WKCONN_E;
		}

		if (t1 != t2) {
			/*
			 * On some controllers, Wake-On-Disconnect will
			 * generate false wakeup signals until the bus
			 * switches over to full-speed idle.  For their
			 * sake, add a delay if we need one.
			 */
			if ((t2 & PORT_WKDISC_E) &&
					ehci_port_speed(ehci, t2) ==
						USB_PORT_STAT_HIGH_SPEED)
				fs_idle_delay = true;
			ehci_writel(ehci, t2, reg);
			changed = 1;
		}
	}
	spin_unlock_irq(&ehci->lock);

	if (changed && ehci_has_fsl_susp_errata(ehci))
		/*
		 * Wait for at least 10 millisecondes to ensure the controller
		 * enter the suspend status before initiating a port resume
		 * using the Force Port Resume bit (Not-EHCI compatible).
		 */
		usleep_range(10000, 20000);

	if ((changed && ehci->has_tdi_phy_lpm) || fs_idle_delay) {
		/*
		 * Wait for HCD to enter low-power mode or for the bus
		 * to switch to full-speed idle.
		 */
		usleep_range(5000, 5500);
	}

	if (changed && ehci->has_tdi_phy_lpm) {
		spin_lock_irq(&ehci->lock);
		port = HCS_N_PORTS(ehci->hcs_params);
		while (port--) {
			u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[port];
			u32		t3;

			t3 = ehci_readl(ehci, hostpc_reg);
			ehci_writel(ehci, t3 | HOSTPC_PHCD, hostpc_reg);
			t3 = ehci_readl(ehci, hostpc_reg);
			ehci_dbg(ehci, "Port %d phy low-power mode %s\n",
					port, (t3 & HOSTPC_PHCD) ?
					"succeeded" : "failed");
		}
		spin_unlock_irq(&ehci->lock);
	}

	/* Apparently some devices need a >= 1-uframe delay here */
	if (ehci->bus_suspended)
		udelay(150);

	/* turn off now-idle HC */
	ehci_halt (ehci);

	spin_lock_irq(&ehci->lock);
	if (ehci->enabled_hrtimer_events & BIT(EHCI_HRTIMER_POLL_DEAD))
		ehci_handle_controller_death(ehci);
	if (ehci->rh_state != EHCI_RH_RUNNING)
		goto done;
	ehci->rh_state = EHCI_RH_SUSPENDED;

	unlink_empty_async_suspended(ehci);

	/* Any IAA cycle that started before the suspend is now invalid */
	end_iaa_cycle(ehci);
	ehci_handle_start_intr_unlinks(ehci);
	ehci_handle_intr_unlinks(ehci);
	end_free_itds(ehci);

	/* allow remote wakeup */
	mask = INTR_MASK;
	if (!hcd->self.root_hub->do_remote_wakeup)
		mask &= ~STS_PCD;
	ehci_writel(ehci, mask, &ehci->regs->intr_enable);
	ehci_readl(ehci, &ehci->regs->intr_enable);

 done:
	ehci->next_statechange = jiffies + msecs_to_jiffies(10);
	ehci->enabled_hrtimer_events = 0;
	ehci->next_hrtimer_event = EHCI_HRTIMER_NO_EVENT;
	spin_unlock_irq (&ehci->lock);

	hrtimer_cancel(&ehci->hrtimer);
	return 0;
}


/* caller has locked the root hub, and should reset/reinit on error */
static int ehci_bus_resume (struct usb_hcd *hcd)
{
	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
	u32			temp;
	u32			power_okay;
	int			i;
	unsigned long		resume_needed = 0;

	if (time_before (jiffies, ehci->next_statechange))
		msleep(5);
	spin_lock_irq (&ehci->lock);
	if (!HCD_HW_ACCESSIBLE(hcd) || ehci->shutdown)
		goto shutdown;

	if (unlikely(ehci->debug)) {
		if (!dbgp_reset_prep(hcd))
			ehci->debug = NULL;
		else
			dbgp_external_startup(hcd);
	}

	/* Ideally and we've got a real resume here, and no port's power
	 * was lost.  (For PCI, that means Vaux was maintained.)  But we
	 * could instead be restoring a swsusp snapshot -- so that BIOS was
	 * the last user of the controller, not reset/pm hardware keeping
	 * state we gave to it.
	 */
	power_okay = ehci_readl(ehci, &ehci->regs->intr_enable);
	ehci_dbg(ehci, "resume root hub%s\n",
			power_okay ? "" : " after power loss");

	/* at least some APM implementations will try to deliver
	 * IRQs right away, so delay them until we're ready.
	 */
	ehci_writel(ehci, 0, &ehci->regs->intr_enable);

	/* re-init operational registers */
	ehci_writel(ehci, 0, &ehci->regs->segment);
	ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
	ehci_writel(ehci, (u32) ehci->async->qh_dma, &ehci->regs->async_next);

	/* restore CMD_RUN, framelist size, and irq threshold */
	ehci->command |= CMD_RUN;
	ehci_writel(ehci, ehci->command, &ehci->regs->command);
	ehci->rh_state = EHCI_RH_RUNNING;

	/*
	 * According to Bugzilla #8190, the port status for some controllers
	 * will be wrong without a delay. At their wrong status, the port
	 * is enabled, but not suspended neither resumed.
	 */
	i = HCS_N_PORTS(ehci->hcs_params);
	while (i--) {
		temp = ehci_readl(ehci, &ehci->regs->port_status[i]);
		if ((temp & PORT_PE) &&
				!(temp & (PORT_SUSPEND | PORT_RESUME))) {
			ehci_dbg(ehci, "Port status(0x%x) is wrong\n", temp);
			spin_unlock_irq(&ehci->lock);
			msleep(8);
			spin_lock_irq(&ehci->lock);
			break;
		}
	}

	if (ehci->shutdown)
		goto shutdown;

	/* clear phy low-power mode before resume */
	if (ehci->bus_suspended && ehci->has_tdi_phy_lpm) {
		i = HCS_N_PORTS(ehci->hcs_params);
		while (i--) {
			if (test_bit(i, &ehci->bus_suspended)) {
				u32 __iomem	*hostpc_reg =
							&ehci->regs->hostpc[i];

				temp = ehci_readl(ehci, hostpc_reg);
				ehci_writel(ehci, temp & ~HOSTPC_PHCD,
						hostpc_reg);
			}
		}
		spin_unlock_irq(&ehci->lock);
		msleep(5);
		spin_lock_irq(&ehci->lock);
		if (ehci->shutdown)
			goto shutdown;
	}

	/* manually resume the ports we suspended during bus_suspend() */
	i = HCS_N_PORTS (ehci->hcs_params);
	while (i--) {
		temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
		temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
		if (test_bit(i, &ehci->bus_suspended) &&
				(temp & PORT_SUSPEND)) {
			temp |= PORT_RESUME;
			set_bit(i, &resume_needed);
		}
		ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
	}

	/*
	 * msleep for USB_RESUME_TIMEOUT ms only if code is trying to resume
	 * port
	 */
	if (resume_needed) {
		spin_unlock_irq(&ehci->lock);
		msleep(USB_RESUME_TIMEOUT);
		spin_lock_irq(&ehci->lock);
		if (ehci->shutdown)
			goto shutdown;
	}

	i = HCS_N_PORTS (ehci->hcs_params);
	while (i--) {
		temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
		if (test_bit(i, &resume_needed)) {
			temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
			ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
		}
	}

	ehci->next_statechange = jiffies + msecs_to_jiffies(5);
	spin_unlock_irq(&ehci->lock);

	ehci_handover_companion_ports(ehci);

	/* Now we can safely re-enable irqs */
	spin_lock_irq(&ehci->lock);
	if (ehci->shutdown)
		goto shutdown;
	ehci_writel(ehci, INTR_MASK, &ehci->regs->intr_enable);
	(void) ehci_readl(ehci, &ehci->regs->intr_enable);
	spin_unlock_irq(&ehci->lock);

	return 0;

 shutdown:
	spin_unlock_irq(&ehci->lock);
	return -ESHUTDOWN;
}

static unsigned long ehci_get_resuming_ports(struct usb_hcd *hcd)
{
	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);

	return ehci->resuming_ports;
}

#else

#define ehci_bus_suspend	NULL
#define ehci_bus_resume		NULL
#define ehci_get_resuming_ports	NULL

#endif	/* CONFIG_PM */

/*-------------------------------------------------------------------------*/

/*
 * Sets the owner of a port
 */
static void set_owner(struct ehci_hcd *ehci, int portnum, int new_owner)
{
	u32 __iomem		*status_reg;
	u32			port_status;
	int 			try;

	status_reg = &ehci->regs->port_status[portnum];

	/*
	 * The controller won't set the OWNER bit if the port is
	 * enabled, so this loop will sometimes require at least two
	 * iterations: one to disable the port and one to set OWNER.
	 */
	for (try = 4; try > 0; --try) {
		spin_lock_irq(&ehci->lock);
		port_status = ehci_readl(ehci, status_reg);
		if ((port_status & PORT_OWNER) == new_owner
				|| (port_status & (PORT_OWNER | PORT_CONNECT))
					== 0)
			try = 0;
		else {
			port_status ^= PORT_OWNER;
			port_status &= ~(PORT_PE | PORT_RWC_BITS);
			ehci_writel(ehci, port_status, status_reg);
		}
		spin_unlock_irq(&ehci->lock);
		if (try > 1)
			msleep(5);
	}
}

/*-------------------------------------------------------------------------*/

static int check_reset_complete (
	struct ehci_hcd	*ehci,
	int		index,
	u32 __iomem	*status_reg,
	int		port_status
) {
	if (!(port_status & PORT_CONNECT))
		return port_status;

	/* if reset finished and it's still not enabled -- handoff */
	if (!(port_status & PORT_PE)) {

		/* with integrated TT, there's nobody to hand it to! */
		if (ehci_is_TDI(ehci)) {
			ehci_dbg (ehci,
				"Failed to enable port %d on root hub TT\n",
				index+1);
			return port_status;
		}

		ehci_dbg (ehci, "port %d full speed --> companion\n",
			index + 1);

		// what happens if HCS_N_CC(params) == 0 ?
		port_status |= PORT_OWNER;
		port_status &= ~PORT_RWC_BITS;
		ehci_writel(ehci, port_status, status_reg);

		/* ensure 440EPX ohci controller state is operational */
		if (ehci->has_amcc_usb23)
			set_ohci_hcfs(ehci, 1);
	} else {
		ehci_dbg(ehci, "port %d reset complete, port enabled\n",
			index + 1);
		/* ensure 440EPx ohci controller state is suspended */
		if (ehci->has_amcc_usb23)
			set_ohci_hcfs(ehci, 0);
	}

	return port_status;
}

/*-------------------------------------------------------------------------*/


/* build "status change" packet (one or two bytes) from HC registers */

static int
ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
{
	struct ehci_hcd	*ehci = hcd_to_ehci (hcd);
	u32		temp, status;
	u32		mask;
	int		ports, i, retval = 1;
	unsigned long	flags;
	u32		ppcd = ~0;

	/* init status to no-changes */
	buf [0] = 0;
	ports = HCS_N_PORTS (ehci->hcs_params);
	if (ports > 7) {
		buf [1] = 0;
		retval++;
	}

	/* Inform the core about resumes-in-progress by returning
	 * a non-zero value even if there are no status changes.
	 */
	status = ehci->resuming_ports;

	/* Some boards (mostly VIA?) report bogus overcurrent indications,
	 * causing massive log spam unless we completely ignore them.  It
	 * may be relevant that VIA VT8235 controllers, where PORT_POWER is
	 * always set, seem to clear PORT_OCC and PORT_CSC when writing to
	 * PORT_POWER; that's surprising, but maybe within-spec.
	 */
	if (!ignore_oc)
		mask = PORT_CSC | PORT_PEC | PORT_OCC;
	else
		mask = PORT_CSC | PORT_PEC;
	// PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND

	/* no hub change reports (bit 0) for now (power, ...) */

	/* port N changes (bit N)? */
	spin_lock_irqsave (&ehci->lock, flags);

	/* get per-port change detect bits */
	if (ehci->has_ppcd)
		ppcd = ehci_readl(ehci, &ehci->regs->status) >> 16;

	for (i = 0; i < ports; i++) {
		/* leverage per-port change bits feature */
		if (ppcd & (1 << i))
			temp = ehci_readl(ehci, &ehci->regs->port_status[i]);
		else
			temp = 0;

		/*
		 * Return status information even for ports with OWNER set.
		 * Otherwise hub_wq wouldn't see the disconnect event when a
		 * high-speed device is switched over to the companion
		 * controller by the user.
		 */

		if ((temp & mask) != 0 || test_bit(i, &ehci->port_c_suspend)
				|| (ehci->reset_done[i] && time_after_eq(
					jiffies, ehci->reset_done[i]))) {
			if (i < 7)
			    buf [0] |= 1 << (i + 1);
			else
			    buf [1] |= 1 << (i - 7);
			status = STS_PCD;
		}
	}

	/* If a resume is in progress, make sure it can finish */
	if (ehci->resuming_ports)
		mod_timer(&hcd->rh_timer, jiffies + msecs_to_jiffies(25));

	spin_unlock_irqrestore (&ehci->lock, flags);
	return status ? retval : 0;
}

/*-------------------------------------------------------------------------*/

static void
ehci_hub_descriptor (
	struct ehci_hcd			*ehci,
	struct usb_hub_descriptor	*desc
) {
	int		ports = HCS_N_PORTS (ehci->hcs_params);
	u16		temp;

	desc->bDescriptorType = USB_DT_HUB;
	desc->bPwrOn2PwrGood = 10;	/* ehci 1.0, 2.3.9 says 20ms max */
	desc->bHubContrCurrent = 0;

	desc->bNbrPorts = ports;
	temp = 1 + (ports / 8);
	desc->bDescLength = 7 + 2 * temp;

	/* two bitmaps:  ports removable, and usb 1.0 legacy PortPwrCtrlMask */
	memset(&desc->u.hs.DeviceRemovable[0], 0, temp);
	memset(&desc->u.hs.DeviceRemovable[temp], 0xff, temp);

	temp = HUB_CHAR_INDV_PORT_OCPM;	/* per-port overcurrent reporting */
	if (HCS_PPC (ehci->hcs_params))
		temp |= HUB_CHAR_INDV_PORT_LPSM; /* per-port power control */
	else
		temp |= HUB_CHAR_NO_LPSM; /* no power switching */
#if 0
// re-enable when we support USB_PORT_FEAT_INDICATOR below.
	if (HCS_INDICATOR (ehci->hcs_params))
		temp |= HUB_CHAR_PORTIND; /* per-port indicators (LEDs) */
#endif
	desc->wHubCharacteristics = cpu_to_le16(temp);
}

/*-------------------------------------------------------------------------*/
#ifdef CONFIG_USB_HCD_TEST_MODE

#define EHSET_TEST_SINGLE_STEP_SET_FEATURE 0x06

static void usb_ehset_completion(struct urb *urb)
{
	struct completion  *done = urb->context;

	complete(done);
}
static int submit_single_step_set_feature(
	struct usb_hcd	*hcd,
	struct urb	*urb,
	int		is_setup
);

/*
 * Allocate and initialize a control URB. This request will be used by the
 * EHSET SINGLE_STEP_SET_FEATURE test in which the DATA and STATUS stages
 * of the GetDescriptor request are sent 15 seconds after the SETUP stage.
 * Return NULL if failed.
 */
static struct urb *request_single_step_set_feature_urb(
	struct usb_device	*udev,
	void			*dr,
	void			*buf,
	struct completion	*done
) {
	struct urb *urb;
	struct usb_hcd *hcd = bus_to_hcd(udev->bus);
	struct usb_host_endpoint *ep;

	urb = usb_alloc_urb(0, GFP_KERNEL);
	if (!urb)
		return NULL;

	urb->pipe = usb_rcvctrlpipe(udev, 0);
	ep = (usb_pipein(urb->pipe) ? udev->ep_in : udev->ep_out)
				[usb_pipeendpoint(urb->pipe)];
	if (!ep) {
		usb_free_urb(urb);
		return NULL;
	}

	urb->ep = ep;
	urb->dev = udev;
	urb->setup_packet = (void *)dr;
	urb->transfer_buffer = buf;
	urb->transfer_buffer_length = USB_DT_DEVICE_SIZE;
	urb->complete = usb_ehset_completion;
	urb->status = -EINPROGRESS;
	urb->actual_length = 0;
	urb->transfer_flags = URB_DIR_IN;
	usb_get_urb(urb);
	atomic_inc(&urb->use_count);
	atomic_inc(&urb->dev->urbnum);
	urb->setup_dma = dma_map_single(
			hcd->self.sysdev,
			urb->setup_packet,
			sizeof(struct usb_ctrlrequest),
			DMA_TO_DEVICE);
	urb->transfer_dma = dma_map_single(
			hcd->self.sysdev,
			urb->transfer_buffer,
			urb->transfer_buffer_length,
			DMA_FROM_DEVICE);
	urb->context = done;
	return urb;
}

static int ehset_single_step_set_feature(struct usb_hcd *hcd, int port)
{
	int retval = -ENOMEM;
	struct usb_ctrlrequest *dr;
	struct urb *urb;
	struct usb_device *udev;
	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
	struct usb_device_descriptor *buf;
	DECLARE_COMPLETION_ONSTACK(done);

	/* Obtain udev of the rhub's child port */
	udev = usb_hub_find_child(hcd->self.root_hub, port);
	if (!udev) {
		ehci_err(ehci, "No device attached to the RootHub\n");
		return -ENODEV;
	}
	buf = kmalloc(USB_DT_DEVICE_SIZE, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_KERNEL);
	if (!dr) {
		kfree(buf);
		return -ENOMEM;
	}

	/* Fill Setup packet for GetDescriptor */
	dr->bRequestType = USB_DIR_IN;
	dr->bRequest = USB_REQ_GET_DESCRIPTOR;
	dr->wValue = cpu_to_le16(USB_DT_DEVICE << 8);
	dr->wIndex = 0;
	dr->wLength = cpu_to_le16(USB_DT_DEVICE_SIZE);
	urb = request_single_step_set_feature_urb(udev, dr, buf, &done);
	if (!urb)
		goto cleanup;

	/* Submit just the SETUP stage */
	retval = submit_single_step_set_feature(hcd, urb, 1);
	if (retval)
		goto out1;
	if (!wait_for_completion_timeout(&done, msecs_to_jiffies(2000))) {
		usb_kill_urb(urb);
		retval = -ETIMEDOUT;
		ehci_err(ehci, "%s SETUP stage timed out on ep0\n", __func__);
		goto out1;
	}
	msleep(15 * 1000);

	/* Complete remaining DATA and STATUS stages using the same URB */
	urb->status = -EINPROGRESS;
	usb_get_urb(urb);
	atomic_inc(&urb->use_count);
	atomic_inc(&urb->dev->urbnum);
	retval = submit_single_step_set_feature(hcd, urb, 0);
	if (!retval && !wait_for_completion_timeout(&done,
						msecs_to_jiffies(2000))) {
		usb_kill_urb(urb);
		retval = -ETIMEDOUT;
		ehci_err(ehci, "%s IN stage timed out on ep0\n", __func__);
	}
out1:
	usb_free_urb(urb);
cleanup:
	kfree(dr);
	kfree(buf);
	return retval;
}
#endif /* CONFIG_USB_HCD_TEST_MODE */
/*-------------------------------------------------------------------------*/

int ehci_hub_control(
	struct usb_hcd	*hcd,
	u16		typeReq,
	u16		wValue,
	u16		wIndex,
	char		*buf,
	u16		wLength
) {
	struct ehci_hcd	*ehci = hcd_to_ehci (hcd);
	int		ports = HCS_N_PORTS (ehci->hcs_params);
	u32 __iomem	*status_reg, *hostpc_reg;
	u32		temp, temp1, status;
	unsigned long	flags;
	int		retval = 0;
	unsigned	selector;

	/*
	 * Avoid underflow while calculating (wIndex & 0xff) - 1.
	 * The compiler might deduce that wIndex can never be 0 and then
	 * optimize away the tests for !wIndex below.
	 */
	temp = wIndex & 0xff;
	temp -= (temp > 0);
	status_reg = &ehci->regs->port_status[temp];
	hostpc_reg = &ehci->regs->hostpc[temp];

	/*
	 * FIXME:  support SetPortFeatures USB_PORT_FEAT_INDICATOR.
	 * HCS_INDICATOR may say we can change LEDs to off/amber/green.
	 * (track current state ourselves) ... blink for diagnostics,
	 * power, "this is the one", etc.  EHCI spec supports this.
	 */

	spin_lock_irqsave (&ehci->lock, flags);
	switch (typeReq) {
	case ClearHubFeature:
		switch (wValue) {
		case C_HUB_LOCAL_POWER:
		case C_HUB_OVER_CURRENT:
			/* no hub-wide feature/status flags */
			break;
		default:
			goto error;
		}
		break;
	case ClearPortFeature:
		if (!wIndex || wIndex > ports)
			goto error;
		wIndex--;
		temp = ehci_readl(ehci, status_reg);
		temp &= ~PORT_RWC_BITS;

		/*
		 * Even if OWNER is set, so the port is owned by the
		 * companion controller, hub_wq needs to be able to clear
		 * the port-change status bits (especially
		 * USB_PORT_STAT_C_CONNECTION).
		 */

		switch (wValue) {
		case USB_PORT_FEAT_ENABLE:
			ehci_writel(ehci, temp & ~PORT_PE, status_reg);
			break;
		case USB_PORT_FEAT_C_ENABLE:
			ehci_writel(ehci, temp | PORT_PEC, status_reg);
			break;
		case USB_PORT_FEAT_SUSPEND:
			if (temp & PORT_RESET)
				goto error;
			if (ehci->no_selective_suspend)
				break;
#ifdef CONFIG_USB_OTG
			if ((hcd->self.otg_port == (wIndex + 1))
			    && hcd->self.b_hnp_enable) {
				otg_start_hnp(hcd->usb_phy->otg);
				break;
			}
#endif
			if (!(temp & PORT_SUSPEND))
				break;
			if ((temp & PORT_PE) == 0)
				goto error;

			/* clear phy low-power mode before resume */
			if (ehci->has_tdi_phy_lpm) {
				temp1 = ehci_readl(ehci, hostpc_reg);
				ehci_writel(ehci, temp1 & ~HOSTPC_PHCD,
						hostpc_reg);
				spin_unlock_irqrestore(&ehci->lock, flags);
				msleep(5);/* wait to leave low-power mode */
				spin_lock_irqsave(&ehci->lock, flags);
			}
			/* resume signaling for 20 msec */
			temp &= ~PORT_WAKE_BITS;
			ehci_writel(ehci, temp | PORT_RESUME, status_reg);
			ehci->reset_done[wIndex] = jiffies
					+ msecs_to_jiffies(USB_RESUME_TIMEOUT);
			set_bit(wIndex, &ehci->resuming_ports);
			usb_hcd_start_port_resume(&hcd->self, wIndex);
			break;
		case USB_PORT_FEAT_C_SUSPEND:
			clear_bit(wIndex, &ehci->port_c_suspend);
			break;
		case USB_PORT_FEAT_POWER:
			if (HCS_PPC(ehci->hcs_params)) {
				spin_unlock_irqrestore(&ehci->lock, flags);
				ehci_port_power(ehci, wIndex, false);
				spin_lock_irqsave(&ehci->lock, flags);
			}
			break;
		case USB_PORT_FEAT_C_CONNECTION:
			ehci_writel(ehci, temp | PORT_CSC, status_reg);
			break;
		case USB_PORT_FEAT_C_OVER_CURRENT:
			ehci_writel(ehci, temp | PORT_OCC, status_reg);
			break;
		case USB_PORT_FEAT_C_RESET:
			/* GetPortStatus clears reset */
			break;
		default:
			goto error;
		}
		ehci_readl(ehci, &ehci->regs->command);	/* unblock posted write */
		break;
	case GetHubDescriptor:
		ehci_hub_descriptor (ehci, (struct usb_hub_descriptor *)
			buf);
		break;
	case GetHubStatus:
		/* no hub-wide feature/status flags */
		memset (buf, 0, 4);
		//cpu_to_le32s ((u32 *) buf);
		break;
	case GetPortStatus:
		if (!wIndex || wIndex > ports)
			goto error;
		wIndex--;
		status = 0;
		temp = ehci_readl(ehci, status_reg);

		// wPortChange bits
		if (temp & PORT_CSC)
			status |= USB_PORT_STAT_C_CONNECTION << 16;
		if (temp & PORT_PEC)
			status |= USB_PORT_STAT_C_ENABLE << 16;

		if ((temp & PORT_OCC) && !ignore_oc){
			status |= USB_PORT_STAT_C_OVERCURRENT << 16;

			/*
			 * Hubs should disable port power on over-current.
			 * However, not all EHCI implementations do this
			 * automatically, even if they _do_ support per-port
			 * power switching; they're allowed to just limit the
			 * current.  hub_wq will turn the power back on.
			 */
			if (((temp & PORT_OC) || (ehci->need_oc_pp_cycle))
					&& HCS_PPC(ehci->hcs_params)) {
				spin_unlock_irqrestore(&ehci->lock, flags);
				ehci_port_power(ehci, wIndex, false);
				spin_lock_irqsave(&ehci->lock, flags);
				temp = ehci_readl(ehci, status_reg);
			}
		}

		/* no reset or resume pending */
		if (!ehci->reset_done[wIndex]) {

			/* Remote Wakeup received? */
			if (temp & PORT_RESUME) {
				/* resume signaling for 20 msec */
				ehci->reset_done[wIndex] = jiffies
						+ msecs_to_jiffies(20);
				usb_hcd_start_port_resume(&hcd->self, wIndex);
				set_bit(wIndex, &ehci->resuming_ports);
				/* check the port again */
				mod_timer(&ehci_to_hcd(ehci)->rh_timer,
						ehci->reset_done[wIndex]);
			}

		/* reset or resume not yet complete */
		} else if (!time_after_eq(jiffies, ehci->reset_done[wIndex])) {
			;	/* wait until it is complete */

		/* resume completed */
		} else if (test_bit(wIndex, &ehci->resuming_ports)) {
			clear_bit(wIndex, &ehci->suspended_ports);
			set_bit(wIndex, &ehci->port_c_suspend);
			ehci->reset_done[wIndex] = 0;
			usb_hcd_end_port_resume(&hcd->self, wIndex);

			/* stop resume signaling */
			temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
			ehci_writel(ehci, temp, status_reg);
			clear_bit(wIndex, &ehci->resuming_ports);
			retval = ehci_handshake(ehci, status_reg,
					PORT_RESUME, 0, 2000 /* 2msec */);
			if (retval != 0) {
				ehci_err(ehci, "port %d resume error %d\n",
						wIndex + 1, retval);
				goto error;
			}
			temp = ehci_readl(ehci, status_reg);

		/* whoever resets must GetPortStatus to complete it!! */
		} else {
			status |= USB_PORT_STAT_C_RESET << 16;
			ehci->reset_done [wIndex] = 0;

			/* force reset to complete */
			ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESET),
					status_reg);
			/* REVISIT:  some hardware needs 550+ usec to clear
			 * this bit; seems too long to spin routinely...
			 */
			retval = ehci_handshake(ehci, status_reg,
					PORT_RESET, 0, 1000);
			if (retval != 0) {
				ehci_err (ehci, "port %d reset error %d\n",
					wIndex + 1, retval);
				goto error;
			}

			/* see what we found out */
			temp = check_reset_complete (ehci, wIndex, status_reg,
					ehci_readl(ehci, status_reg));
		}

		/* transfer dedicated ports to the companion hc */
		if ((temp & PORT_CONNECT) &&
				test_bit(wIndex, &ehci->companion_ports)) {
			temp &= ~PORT_RWC_BITS;
			temp |= PORT_OWNER;
			ehci_writel(ehci, temp, status_reg);
			ehci_dbg(ehci, "port %d --> companion\n", wIndex + 1);
			temp = ehci_readl(ehci, status_reg);
		}

		/*
		 * Even if OWNER is set, there's no harm letting hub_wq
		 * see the wPortStatus values (they should all be 0 except
		 * for PORT_POWER anyway).
		 */

		if (temp & PORT_CONNECT) {
			status |= USB_PORT_STAT_CONNECTION;
			// status may be from integrated TT
			if (ehci->has_hostpc) {
				temp1 = ehci_readl(ehci, hostpc_reg);
				status |= ehci_port_speed(ehci, temp1);
			} else
				status |= ehci_port_speed(ehci, temp);
		}
		if (temp & PORT_PE)
			status |= USB_PORT_STAT_ENABLE;

		/* maybe the port was unsuspended without our knowledge */
		if (temp & (PORT_SUSPEND|PORT_RESUME)) {
			status |= USB_PORT_STAT_SUSPEND;
		} else if (test_bit(wIndex, &ehci->suspended_ports)) {
			clear_bit(wIndex, &ehci->suspended_ports);
			clear_bit(wIndex, &ehci->resuming_ports);
			ehci->reset_done[wIndex] = 0;
			if (temp & PORT_PE)
				set_bit(wIndex, &ehci->port_c_suspend);
			usb_hcd_end_port_resume(&hcd->self, wIndex);
		}

		if (temp & PORT_OC)
			status |= USB_PORT_STAT_OVERCURRENT;
		if (temp & PORT_RESET)
			status |= USB_PORT_STAT_RESET;
		if (temp & PORT_POWER)
			status |= USB_PORT_STAT_POWER;
		if (test_bit(wIndex, &ehci->port_c_suspend))
			status |= USB_PORT_STAT_C_SUSPEND << 16;

		if (status & ~0xffff)	/* only if wPortChange is interesting */
			dbg_port(ehci, "GetStatus", wIndex + 1, temp);
		put_unaligned_le32(status, buf);
		break;
	case SetHubFeature:
		switch (wValue) {
		case C_HUB_LOCAL_POWER:
		case C_HUB_OVER_CURRENT:
			/* no hub-wide feature/status flags */
			break;
		default:
			goto error;
		}
		break;
	case SetPortFeature:
		selector = wIndex >> 8;
		wIndex &= 0xff;
		if (unlikely(ehci->debug)) {
			/* If the debug port is active any port
			 * feature requests should get denied */
			if (wIndex == HCS_DEBUG_PORT(ehci->hcs_params) &&
			    (readl(&ehci->debug->control) & DBGP_ENABLED)) {
				retval = -ENODEV;
				goto error_exit;
			}
		}
		if (!wIndex || wIndex > ports)
			goto error;
		wIndex--;
		temp = ehci_readl(ehci, status_reg);
		if (temp & PORT_OWNER)
			break;

		temp &= ~PORT_RWC_BITS;
		switch (wValue) {
		case USB_PORT_FEAT_SUSPEND:
			if (ehci->no_selective_suspend)
				break;
			if ((temp & PORT_PE) == 0
					|| (temp & PORT_RESET) != 0)
				goto error;

			/* After above check the port must be connected.
			 * Set appropriate bit thus could put phy into low power
			 * mode if we have tdi_phy_lpm feature
			 */
			temp &= ~PORT_WKCONN_E;
			temp |= PORT_WKDISC_E | PORT_WKOC_E;
			ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
			if (ehci->has_tdi_phy_lpm) {
				spin_unlock_irqrestore(&ehci->lock, flags);
				msleep(5);/* 5ms for HCD enter low pwr mode */
				spin_lock_irqsave(&ehci->lock, flags);
				temp1 = ehci_readl(ehci, hostpc_reg);
				ehci_writel(ehci, temp1 | HOSTPC_PHCD,
					hostpc_reg);
				temp1 = ehci_readl(ehci, hostpc_reg);
				ehci_dbg(ehci, "Port%d phy low pwr mode %s\n",
					wIndex, (temp1 & HOSTPC_PHCD) ?
					"succeeded" : "failed");
			}
			if (ehci_has_fsl_susp_errata(ehci)) {
				/* 10ms for HCD enter suspend */
				spin_unlock_irqrestore(&ehci->lock, flags);
				usleep_range(10000, 20000);
				spin_lock_irqsave(&ehci->lock, flags);
			}
			set_bit(wIndex, &ehci->suspended_ports);
			break;
		case USB_PORT_FEAT_POWER:
			if (HCS_PPC(ehci->hcs_params)) {
				spin_unlock_irqrestore(&ehci->lock, flags);
				ehci_port_power(ehci, wIndex, true);
				spin_lock_irqsave(&ehci->lock, flags);
			}
			break;
		case USB_PORT_FEAT_RESET:
			if (temp & (PORT_SUSPEND|PORT_RESUME))
				goto error;
			/* line status bits may report this as low speed,
			 * which can be fine if this root hub has a
			 * transaction translator built in.
			 */
			if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
					&& !ehci_is_TDI(ehci)
					&& PORT_USB11 (temp)) {
				ehci_dbg (ehci,
					"port %d low speed --> companion\n",
					wIndex + 1);
				temp |= PORT_OWNER;
			} else {
				temp |= PORT_RESET;
				temp &= ~PORT_PE;

				/*
				 * caller must wait, then call GetPortStatus
				 * usb 2.0 spec says 50 ms resets on root
				 */
				ehci->reset_done [wIndex] = jiffies
						+ msecs_to_jiffies (50);

				/*
				 * Force full-speed connect for FSL high-speed
				 * erratum; disable HS Chirp by setting PFSC bit
				 */
				if (ehci_has_fsl_hs_errata(ehci))
					temp |= (1 << PORTSC_FSL_PFSC);
			}
			ehci_writel(ehci, temp, status_reg);
			break;

		/* For downstream facing ports (these):  one hub port is put
		 * into test mode according to USB2 11.24.2.13, then the hub
		 * must be reset (which for root hub now means rmmod+modprobe,
		 * or else system reboot).  See EHCI 2.3.9 and 4.14 for info
		 * about the EHCI-specific stuff.
		 */
		case USB_PORT_FEAT_TEST:
#ifdef CONFIG_USB_HCD_TEST_MODE
			if (selector == EHSET_TEST_SINGLE_STEP_SET_FEATURE) {
				spin_unlock_irqrestore(&ehci->lock, flags);
				retval = ehset_single_step_set_feature(hcd,
								wIndex + 1);
				spin_lock_irqsave(&ehci->lock, flags);
				break;
			}
#endif
			if (!selector || selector > 5)
				goto error;
			spin_unlock_irqrestore(&ehci->lock, flags);
			ehci_quiesce(ehci);
			spin_lock_irqsave(&ehci->lock, flags);

			/* Put all enabled ports into suspend */
			while (ports--) {
				u32 __iomem *sreg =
						&ehci->regs->port_status[ports];

				temp = ehci_readl(ehci, sreg) & ~PORT_RWC_BITS;
				if (temp & PORT_PE)
					ehci_writel(ehci, temp | PORT_SUSPEND,
							sreg);
			}

			spin_unlock_irqrestore(&ehci->lock, flags);
			ehci_halt(ehci);
			spin_lock_irqsave(&ehci->lock, flags);

			temp = ehci_readl(ehci, status_reg);
			temp |= selector << 16;
			ehci_writel(ehci, temp, status_reg);
			break;

		default:
			goto error;
		}
		ehci_readl(ehci, &ehci->regs->command);	/* unblock posted writes */
		break;

	default:
error:
		/* "stall" on error */
		retval = -EPIPE;
	}
error_exit:
	spin_unlock_irqrestore (&ehci->lock, flags);
	return retval;
}
EXPORT_SYMBOL_GPL(ehci_hub_control);

static void ehci_relinquish_port(struct usb_hcd *hcd, int portnum)
{
	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);

	if (ehci_is_TDI(ehci))
		return;
	set_owner(ehci, --portnum, PORT_OWNER);
}

static int ehci_port_handed_over(struct usb_hcd *hcd, int portnum)
{
	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);
	u32 __iomem		*reg;

	if (ehci_is_TDI(ehci))
		return 0;
	reg = &ehci->regs->port_status[portnum - 1];
	return ehci_readl(ehci, reg) & PORT_OWNER;
}

static int ehci_port_power(struct ehci_hcd *ehci, int portnum, bool enable)
{
	struct usb_hcd *hcd = ehci_to_hcd(ehci);
	u32 __iomem *status_reg = &ehci->regs->port_status[portnum];
	u32 temp = ehci_readl(ehci, status_reg) & ~PORT_RWC_BITS;

	if (enable)
		ehci_writel(ehci, temp | PORT_POWER, status_reg);
	else
		ehci_writel(ehci, temp & ~PORT_POWER, status_reg);

	if (hcd->driver->port_power)
		hcd->driver->port_power(hcd, portnum, enable);

	return 0;
}