mirror of https://gitee.com/openkylin/linux.git
Input: atmel_mxt_ts - convert bindings to YAML and extend
This converts the Armel MXT touchscreen bindings to YAML format and extends them with the following two properties: - vdda-supply: the optional analog supply voltage - vdd-supply: the optional digital supply voltage Tested the schema with all in-tree users and they verify fine. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20201104153032.1387747-2-linus.walleij@linaro.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit is contained in:
parent
feedaacdad
commit
04f1842a8d
|
@ -1,41 +0,0 @@
|
|||
Atmel maXTouch touchscreen/touchpad
|
||||
|
||||
Required properties:
|
||||
- compatible:
|
||||
atmel,maxtouch
|
||||
|
||||
The following compatibles have been used in various products but are
|
||||
deprecated:
|
||||
atmel,qt602240_ts
|
||||
atmel,atmel_mxt_ts
|
||||
atmel,atmel_mxt_tp
|
||||
atmel,mXT224
|
||||
|
||||
- reg: The I2C address of the device
|
||||
|
||||
- interrupts: The sink for the touchpad's IRQ output
|
||||
See ../interrupt-controller/interrupts.txt
|
||||
|
||||
Optional properties for main touchpad device:
|
||||
|
||||
- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages
|
||||
on GPIO bit changes. An array of up to 8 entries can be provided
|
||||
indicating the Linux keycode mapped to each bit of the status byte,
|
||||
starting at the LSB. Linux keycodes are defined in
|
||||
<dt-bindings/input/input.h>.
|
||||
|
||||
Note: the numbering of the GPIOs and the bit they start at varies between
|
||||
maXTouch devices. You must either refer to the documentation, or
|
||||
experiment to determine which bit corresponds to which input. Use
|
||||
KEY_RESERVED for unused padding values.
|
||||
|
||||
- reset-gpios: GPIO specifier for the touchscreen's reset pin (active low)
|
||||
|
||||
Example:
|
||||
|
||||
touch@4b {
|
||||
compatible = "atmel,maxtouch";
|
||||
reg = <0x4b>;
|
||||
interrupt-parent = <&gpio>;
|
||||
interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
|
||||
};
|
|
@ -0,0 +1,81 @@
|
|||
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/input/atmel,maxtouch.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: Atmel maXTouch touchscreen/touchpad
|
||||
|
||||
maintainers:
|
||||
- Nick Dyer <nick@shmanahar.org>
|
||||
- Linus Walleij <linus.walleij@linaro.org>
|
||||
|
||||
description: |
|
||||
Atmel maXTouch touchscreen or touchpads such as the mXT244
|
||||
and similar devices.
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
const: atmel,maxtouch
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
interrupts:
|
||||
maxItems: 1
|
||||
|
||||
vdda-supply:
|
||||
description:
|
||||
Optional regulator for the AVDD analog voltage.
|
||||
|
||||
vdd-supply:
|
||||
description:
|
||||
Optional regulator for the VDD digital voltage.
|
||||
|
||||
reset-gpios:
|
||||
maxItems: 1
|
||||
description:
|
||||
Optional GPIO specifier for the touchscreen's reset pin
|
||||
(active low). The line must be flagged with
|
||||
GPIO_ACTIVE_LOW.
|
||||
|
||||
linux,gpio-keymap:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32-array
|
||||
description: |
|
||||
When enabled, the SPT_GPIOPWN_T19 object sends messages
|
||||
on GPIO bit changes. An array of up to 8 entries can be provided
|
||||
indicating the Linux keycode mapped to each bit of the status byte,
|
||||
starting at the LSB. Linux keycodes are defined in
|
||||
<dt-bindings/input/input.h>.
|
||||
|
||||
Note: the numbering of the GPIOs and the bit they start at varies
|
||||
between maXTouch devices. You must either refer to the documentation,
|
||||
or experiment to determine which bit corresponds to which input. Use
|
||||
KEY_RESERVED for unused padding values.
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- interrupts
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
i2c {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
touchscreen@4a {
|
||||
compatible = "atmel,maxtouch";
|
||||
reg = <0x4a>;
|
||||
interrupt-parent = <&gpio>;
|
||||
interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
|
||||
reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
||||
vdda-supply = <&ab8500_ldo_aux2_reg>;
|
||||
vdd-supply = <&ab8500_ldo_aux5_reg>;
|
||||
};
|
||||
};
|
||||
|
||||
...
|
|
@ -2980,7 +2980,7 @@ ATMEL MAXTOUCH DRIVER
|
|||
M: Nick Dyer <nick@shmanahar.org>
|
||||
S: Maintained
|
||||
T: git git://github.com/ndyer/linux.git
|
||||
F: Documentation/devicetree/bindings/input/atmel,maxtouch.txt
|
||||
F: Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
|
||||
F: drivers/input/touchscreen/atmel_mxt_ts.c
|
||||
|
||||
ATMEL WIRELESS DRIVER
|
||||
|
|
Loading…
Reference in New Issue