Merge git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: Move syscalls.h under arch/avr32/include/asm/
  avr32: Define DIE_OOPS
  avr32: Remove DMATEST from defconfigs
  arch/avr32: Eliminate NULL test and memset after alloc_bootmem
  avr32: data param to at32_add_device_mci() must be non-NULL
  atmel-mci: move atmel-mci.h file to include/linux
  avr32: Hammerhead board support
  avr32: Allow reserving multiple pins at once
  favr-32: Remove deprecated call
  MIMC200: Remove deprecated call
  avr: struct device - replace bus_id with dev_name(), dev_set_name()
  avr32: Introducing asm/syscalls.h

arch/avr32/Kconfig

@@ -122,6 +122,24 @@ config BOARD_ATNGW100
 	bool "ATNGW100 Network Gateway"
 	select CPU_AT32AP7000
 
+config BOARD_HAMMERHEAD
+	bool "Hammerhead board"
+	select CPU_AT32AP7000
+	select USB_ARCH_HAS_HCD
+	help
+	  The Hammerhead platform is built around a AVR32 32-bit microcontroller from Atmel.
+	  It offers versatile peripherals, such as ethernet, usb device, usb host etc.
+
+	  The board also incooperates a power supply and is a Power over Ethernet (PoE) Powered
+	  Device (PD).
+
+	  Additonally, a Cyclone III FPGA from Altera is integrated on the board. The FPGA is
+	  mapped into the 32-bit AVR memory bus. The FPGA offers two DDR2 SDRAM interfaces, which
+	  will cover even the most exceptional need of memory bandwidth. Together with the onboard
+	  video decoder the board is ready for video processing.
+
+	  For more information see: http://www.miromico.com/hammerhead
+
 config BOARD_FAVR_32
 	bool "Favr-32 LCD-board"
 	select CPU_AT32AP7000
@@ -133,6 +151,7 @@ endchoice
 
 source "arch/avr32/boards/atstk1000/Kconfig"
 source "arch/avr32/boards/atngw100/Kconfig"
+source "arch/avr32/boards/hammerhead/Kconfig"
 source "arch/avr32/boards/favr-32/Kconfig"
 
 choice

arch/avr32/Makefile

@@ -33,6 +33,7 @@ head-y					+= arch/avr32/kernel/head.o
 core-y					+= $(machdirs)
 core-$(CONFIG_BOARD_ATSTK1000)		+= arch/avr32/boards/atstk1000/
 core-$(CONFIG_BOARD_ATNGW100)		+= arch/avr32/boards/atngw100/
+core-$(CONFIG_BOARD_HAMMERHEAD)		+= arch/avr32/boards/hammerhead/
 core-$(CONFIG_BOARD_FAVR_32)		+= arch/avr32/boards/favr-32/
 core-$(CONFIG_BOARD_MIMC200)		+= arch/avr32/boards/mimc200/
 core-$(CONFIG_LOADER_U_BOOT)		+= arch/avr32/boot/u-boot/

arch/avr32/boards/atngw100/setup.c

@@ -19,8 +19,8 @@
 #include <linux/types.h>
 #include <linux/leds.h>
 #include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
 
-#include <asm/atmel-mci.h>
 #include <asm/io.h>
 #include <asm/setup.h>
 

arch/avr32/boards/atstk1000/atstk1002.c

@@ -16,12 +16,12 @@
 #include <linux/types.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/at73c213.h>
+#include <linux/atmel-mci.h>
 
 #include <video/atmel_lcdc.h>
 
 #include <asm/io.h>
 #include <asm/setup.h>
-#include <asm/atmel-mci.h>
 
 #include <mach/at32ap700x.h>
 #include <mach/board.h>
@@ -287,23 +287,7 @@ static int __init atstk1002_init(void)
 	 * ATSTK1000 uses 32-bit SDRAM interface. Reserve the
 	 * SDRAM-specific pins so that nobody messes with them.
 	 */
-	at32_reserve_pin(GPIO_PIN_PE(0));	/* DATA[16]	*/
+	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
-	at32_reserve_pin(GPIO_PIN_PE(1));	/* DATA[17]	*/
-	at32_reserve_pin(GPIO_PIN_PE(2));	/* DATA[18]	*/
-	at32_reserve_pin(GPIO_PIN_PE(3));	/* DATA[19]	*/
-	at32_reserve_pin(GPIO_PIN_PE(4));	/* DATA[20]	*/
-	at32_reserve_pin(GPIO_PIN_PE(5));	/* DATA[21]	*/
-	at32_reserve_pin(GPIO_PIN_PE(6));	/* DATA[22]	*/
-	at32_reserve_pin(GPIO_PIN_PE(7));	/* DATA[23]	*/
-	at32_reserve_pin(GPIO_PIN_PE(8));	/* DATA[24]	*/
-	at32_reserve_pin(GPIO_PIN_PE(9));	/* DATA[25]	*/
-	at32_reserve_pin(GPIO_PIN_PE(10));	/* DATA[26]	*/
-	at32_reserve_pin(GPIO_PIN_PE(11));	/* DATA[27]	*/
-	at32_reserve_pin(GPIO_PIN_PE(12));	/* DATA[28]	*/
-	at32_reserve_pin(GPIO_PIN_PE(13));	/* DATA[29]	*/
-	at32_reserve_pin(GPIO_PIN_PE(14));	/* DATA[30]	*/
-	at32_reserve_pin(GPIO_PIN_PE(15));	/* DATA[31]	*/
-	at32_reserve_pin(GPIO_PIN_PE(26));	/* SDCS		*/
 
 #ifdef CONFIG_BOARD_ATSTK1006
 	smc_set_timing(&nand_config, &nand_timing);

arch/avr32/boards/atstk1000/atstk1003.c

@@ -17,9 +17,9 @@
 
 #include <linux/spi/at73c213.h>
 #include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
 
 #include <asm/setup.h>
-#include <asm/atmel-mci.h>
 
 #include <mach/at32ap700x.h>
 #include <mach/board.h>
@@ -131,23 +131,7 @@ static int __init atstk1003_init(void)
 	 * ATSTK1000 uses 32-bit SDRAM interface. Reserve the
 	 * SDRAM-specific pins so that nobody messes with them.
 	 */
-	at32_reserve_pin(GPIO_PIN_PE(0));	/* DATA[16]	*/
+	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
-	at32_reserve_pin(GPIO_PIN_PE(1));	/* DATA[17]	*/
-	at32_reserve_pin(GPIO_PIN_PE(2));	/* DATA[18]	*/
-	at32_reserve_pin(GPIO_PIN_PE(3));	/* DATA[19]	*/
-	at32_reserve_pin(GPIO_PIN_PE(4));	/* DATA[20]	*/
-	at32_reserve_pin(GPIO_PIN_PE(5));	/* DATA[21]	*/
-	at32_reserve_pin(GPIO_PIN_PE(6));	/* DATA[22]	*/
-	at32_reserve_pin(GPIO_PIN_PE(7));	/* DATA[23]	*/
-	at32_reserve_pin(GPIO_PIN_PE(8));	/* DATA[24]	*/
-	at32_reserve_pin(GPIO_PIN_PE(9));	/* DATA[25]	*/
-	at32_reserve_pin(GPIO_PIN_PE(10));	/* DATA[26]	*/
-	at32_reserve_pin(GPIO_PIN_PE(11));	/* DATA[27]	*/
-	at32_reserve_pin(GPIO_PIN_PE(12));	/* DATA[28]	*/
-	at32_reserve_pin(GPIO_PIN_PE(13));	/* DATA[29]	*/
-	at32_reserve_pin(GPIO_PIN_PE(14));	/* DATA[30]	*/
-	at32_reserve_pin(GPIO_PIN_PE(15));	/* DATA[31]	*/
-	at32_reserve_pin(GPIO_PIN_PE(26));	/* SDCS		*/
 
 #ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
 	at32_add_device_usart(1);

arch/avr32/boards/atstk1000/atstk1004.c

@@ -17,11 +17,11 @@
 
 #include <linux/spi/at73c213.h>
 #include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
 
 #include <video/atmel_lcdc.h>
 
 #include <asm/setup.h>
-#include <asm/atmel-mci.h>
 
 #include <mach/at32ap700x.h>
 #include <mach/board.h>

arch/avr32/boards/favr-32/setup.c

@@ -17,6 +17,7 @@
 #include <linux/linkage.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
+#include <linux/atmel-mci.h>
 #include <linux/atmel-pwm-bl.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
@@ -79,6 +80,14 @@ static struct spi_board_info __initdata spi1_board_info[] = {
 	},
 };
 
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+
 static struct fb_videomode __initdata lb104v03_modes[] = {
 	{
 		.name		= "640x480 @ 50",
@@ -307,28 +316,10 @@ static int __init favr32_init(void)
 	 * Favr-32 uses 32-bit SDRAM interface. Reserve the SDRAM-specific
 	 * pins so that nobody messes with them.
 	 */
-	at32_reserve_pin(GPIO_PIN_PE(0));	/* DATA[16]	*/
+	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
-	at32_reserve_pin(GPIO_PIN_PE(1));	/* DATA[17]	*/
-	at32_reserve_pin(GPIO_PIN_PE(2));	/* DATA[18]	*/
-	at32_reserve_pin(GPIO_PIN_PE(3));	/* DATA[19]	*/
-	at32_reserve_pin(GPIO_PIN_PE(4));	/* DATA[20]	*/
-	at32_reserve_pin(GPIO_PIN_PE(5));	/* DATA[21]	*/
-	at32_reserve_pin(GPIO_PIN_PE(6));	/* DATA[22]	*/
-	at32_reserve_pin(GPIO_PIN_PE(7));	/* DATA[23]	*/
-	at32_reserve_pin(GPIO_PIN_PE(8));	/* DATA[24]	*/
-	at32_reserve_pin(GPIO_PIN_PE(9));	/* DATA[25]	*/
-	at32_reserve_pin(GPIO_PIN_PE(10));	/* DATA[26]	*/
-	at32_reserve_pin(GPIO_PIN_PE(11));	/* DATA[27]	*/
-	at32_reserve_pin(GPIO_PIN_PE(12));	/* DATA[28]	*/
-	at32_reserve_pin(GPIO_PIN_PE(13));	/* DATA[29]	*/
-	at32_reserve_pin(GPIO_PIN_PE(14));	/* DATA[30]	*/
-	at32_reserve_pin(GPIO_PIN_PE(15));	/* DATA[31]	*/
-	at32_reserve_pin(GPIO_PIN_PE(26));	/* SDCS		*/
 
 	at32_select_gpio(GPIO_PIN_PB(3), 0);	/* IRQ from ADS7843 */
 
-	at32_add_system_devices();
-
 	at32_add_device_usart(0);
 
 	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
@@ -339,7 +330,7 @@ static int __init favr32_init(void)
 
 	at32_add_device_pwm(1 << atmel_pwm_bl_pdata.pwm_channel);
 	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
-	at32_add_device_mci(0, NULL);
+	at32_add_device_mci(0, &mci0_data);
 	at32_add_device_usba(0, NULL);
 	at32_add_device_lcdc(0, &favr32_lcdc_data, fbmem_start, fbmem_size, 0);
 

arch/avr32/boards/hammerhead/Kconfig

@@ -0,0 +1,43 @@
+# Hammerhead customization
+
+if BOARD_HAMMERHEAD
+
+config BOARD_HAMMERHEAD_USB
+	bool "Philips ISP116x-hcd USB support"
+	help
+	  This enables USB support for Hammerheads internal ISP116x
+	  controller from Philips.
+
+	  Choose 'Y' here if you want to have your board USB driven.
+
+config BOARD_HAMMERHEAD_LCD
+	bool "Atmel AT91/AT32 LCD support"
+	help
+	  This enables LCD support for the Hammerhead board. You may
+	  also add support for framebuffer devices (AT91/AT32 LCD Controller)
+	  and framebuffer console support to get the most out of your LCD.
+
+	  Choose 'Y' here if you have ordered a Corona daugther board and
+	  want to have support for your Hantronix HDA-351T-LV LCD.
+
+config BOARD_HAMMERHEAD_SND
+	bool "Atmel AC97 Sound support"
+	help
+	  This enables Sound support for the Hammerhead board. You may
+	  also go trough the ALSA settings to get it working.
+
+	  Choose 'Y' here if you have ordered a Corona daugther board and
+	  want to make your board funky.
+
+config BOARD_HAMMERHEAD_FPGA
+	bool "Hammerhead FPGA Support"
+	default y
+	help
+	  This adds support for the Cyclone III FPGA from Altera
+	  found on Miromico's Hammerhead board.
+
+	  Choose 'Y' here if you want to have FPGA support enabled.
+	  You will have to choose the "Hammerhead FPGA Device Support" in
+	  Device Drivers->Misc to be able to use FPGA functionality.
+
+endif	# BOARD_ATNGW100

arch/avr32/boards/hammerhead/Makefile

@@ -0,0 +1 @@
+obj-y				+= setup.o flash.o

arch/avr32/boards/hammerhead/flash.c

@@ -0,0 +1,377 @@
+/*
+ * Hammerhead board-specific flash initialization
+ *
+ * Copyright (C) 2008 Miromico AG
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/usb/isp116x.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+
+#include <mach/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/smc.h>
+
+#include "../../mach-at32ap/clock.h"
+#include "flash.h"
+
+
+#define HAMMERHEAD_USB_PERIPH_GCLK0	0x40000000
+#define HAMMERHEAD_USB_PERIPH_CS2	0x02000000
+#define HAMMERHEAD_USB_PERIPH_EXTINT0	0x02000000
+
+#define HAMMERHEAD_FPGA_PERIPH_MOSI	0x00000002
+#define HAMMERHEAD_FPGA_PERIPH_SCK	0x00000020
+#define HAMMERHEAD_FPGA_PERIPH_EXTINT3	0x10000000
+
+static struct smc_timing flash_timing __initdata = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 40,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 10,
+
+	.ncs_read_pulse		= 80,
+	.nrd_pulse		= 40,
+	.ncs_write_pulse	= 65,
+	.nwe_pulse		= 55,
+
+	.read_cycle		= 120,
+	.write_cycle		= 120,
+};
+
+static struct smc_config flash_config __initdata = {
+	.bus_width		= 2,
+	.nrd_controlled		= 1,
+	.nwe_controlled		= 1,
+	.byte_write		= 1,
+};
+
+static struct mtd_partition flash_parts[] = {
+	{
+		.name		= "u-boot",
+		.offset		= 0x00000000,
+		.size		= 0x00020000,           /* 128 KiB */
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	{
+		.name		= "root",
+		.offset		= 0x00020000,
+		.size		= 0x007d0000,
+	},
+	{
+		.name		= "env",
+		.offset		= 0x007f0000,
+		.size		= 0x00010000,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+};
+
+static struct physmap_flash_data flash_data = {
+	.width		= 2,
+	.nr_parts	= ARRAY_SIZE(flash_parts),
+	.parts		= flash_parts,
+};
+
+static struct resource flash_resource = {
+	.start		= 0x00000000,
+	.end		= 0x007fffff,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device flash_device = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.resource	= &flash_resource,
+	.num_resources	= 1,
+	.dev		= { .platform_data = &flash_data, },
+};
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_USB
+
+static struct smc_timing isp1160_timing __initdata = {
+	.ncs_read_setup		= 75,
+	.nrd_setup		= 75,
+	.ncs_write_setup	= 75,
+	.nwe_setup		= 75,
+
+
+	/* We use conservative timing settings, as the minimal settings aren't
+	   stable. There may be room for tweaking. */
+	.ncs_read_pulse		= 75,  /* min. 33ns */
+	.nrd_pulse		= 75,  /* min. 33ns */
+	.ncs_write_pulse	= 75,  /* min. 26ns */
+	.nwe_pulse		= 75,  /* min. 26ns */
+
+	.read_cycle		= 225, /* min. 143ns */
+	.write_cycle		= 225, /* min. 136ns */
+};
+
+static struct smc_config isp1160_config __initdata = {
+	.bus_width		= 2,
+	.nrd_controlled		= 1,
+	.nwe_controlled		= 1,
+	.byte_write		= 0,
+};
+
+/*
+ * The platform delay function is only used to enforce the strange
+ * read to write delay. This can not be configured in the SMC. All other
+ * timings are controlled by the SMC (see timings obove)
+ * So in isp116x-hcd.c we should comment out USE_PLATFORM_DELAY
+ */
+void isp116x_delay(struct device *dev, int delay)
+{
+	if (delay > 150)
+		ndelay(delay - 150);
+}
+
+static struct  isp116x_platform_data isp1160_data = {
+	.sel15Kres		= 1,	/* use internal downstream resistors */
+	.oc_enable		= 0,	/* external overcurrent detection */
+	.int_edge_triggered	= 0,	/* interrupt is level triggered */
+	.int_act_high		= 0,	/* interrupt is active low */
+	.delay = isp116x_delay,		/* platform delay function */
+};
+
+static struct resource isp1160_resource[] = {
+	{
+		.start		= 0x08000000,
+		.end		= 0x08000001,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= 0x08000002,
+		.end		= 0x08000003,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= 64,
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device isp1160_device = {
+	.name		= "isp116x-hcd",
+	.id		= 0,
+	.resource	= isp1160_resource,
+	.num_resources	= 3,
+	.dev		= {
+		.platform_data = &isp1160_data,
+	},
+};
+#endif
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_USB
+static int __init hammerhead_usbh_init(void)
+{
+	struct clk *gclk;
+	struct clk *osc;
+
+	int ret;
+
+	/* setup smc for usbh */
+	smc_set_timing(&isp1160_config, &isp1160_timing);
+	ret = smc_set_configuration(2, &isp1160_config);
+
+	if (ret < 0) {
+		printk(KERN_ERR
+		       "hammerhead: failed to set ISP1160 USBH timing\n");
+		return ret;
+	}
+
+	/* setup gclk0 to run from osc1 */
+	gclk = clk_get(NULL, "gclk0");
+	if (IS_ERR(gclk))
+		goto err_gclk;
+
+	osc = clk_get(NULL, "osc1");
+	if (IS_ERR(osc))
+		goto err_osc;
+
+	if (clk_set_parent(gclk, osc)) {
+		pr_debug("hammerhead: failed to set osc1 for USBH clock\n");
+		goto err_set_clk;
+	}
+
+	/* set clock to 6MHz */
+	clk_set_rate(gclk, 6000000);
+
+	/* and enable */
+	clk_enable(gclk);
+
+	/* select GCLK0 peripheral function */
+	at32_select_periph(GPIO_PIOA_BASE, HAMMERHEAD_USB_PERIPH_GCLK0,
+			   GPIO_PERIPH_A, 0);
+
+	/* enable CS2 peripheral function */
+	at32_select_periph(GPIO_PIOE_BASE, HAMMERHEAD_USB_PERIPH_CS2,
+			   GPIO_PERIPH_A, 0);
+
+	/* H_WAKEUP must be driven low */
+	at32_select_gpio(GPIO_PIN_PA(8), AT32_GPIOF_OUTPUT);
+
+	/* Select EXTINT0 for PB25 */
+	at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_USB_PERIPH_EXTINT0,
+			   GPIO_PERIPH_A, 0);
+
+	/* register usbh device driver */
+	platform_device_register(&isp1160_device);
+
+ err_set_clk:
+	clk_put(osc);
+ err_osc:
+	clk_put(gclk);
+ err_gclk:
+	return ret;
+}
+#endif
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
+static struct smc_timing fpga_timing __initdata = {
+	.ncs_read_setup		= 16,
+	.nrd_setup		= 32,
+	.ncs_read_pulse		= 48,
+	.nrd_pulse		= 32,
+	.read_cycle		= 64,
+
+	.ncs_write_setup	= 16,
+	.nwe_setup		= 16,
+	.ncs_write_pulse	= 32,
+	.nwe_pulse		= 32,
+	.write_cycle		= 64,
+};
+
+static struct smc_config fpga_config __initdata = {
+	.bus_width		= 4,
+	.nrd_controlled		= 1,
+	.nwe_controlled		= 1,
+	.byte_write		= 0,
+};
+
+static struct resource hh_fpga0_resource[] = {
+	{
+		.start		= 0xffe00400,
+		.end		= 0xffe00400 + 0x3ff,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= 4,
+		.end		= 4,
+		.flags		= IORESOURCE_IRQ,
+	},
+	{
+		.start		= 0x0c000000,
+		.end		= 0x0c000100,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= 67,
+		.end		= 67,
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static u64 hh_fpga0_dma_mask = DMA_32BIT_MASK;
+static struct platform_device hh_fpga0_device = {
+	.name		= "hh_fpga",
+	.id		= 0,
+	.dev		= {
+		.dma_mask = &hh_fpga0_dma_mask,
+		.coherent_dma_mask = DMA_32BIT_MASK,
+	},
+	.resource	= hh_fpga0_resource,
+	.num_resources	= ARRAY_SIZE(hh_fpga0_resource),
+};
+
+static struct clk hh_fpga0_spi_clk = {
+	.name		= "spi_clk",
+	.dev		= &hh_fpga0_device.dev,
+	.mode		= pba_clk_mode,
+	.get_rate	= pba_clk_get_rate,
+	.index		= 1,
+};
+
+struct platform_device *__init at32_add_device_hh_fpga(void)
+{
+	/* Select peripheral functionallity for SPI SCK and MOSI */
+	at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_SCK,
+			   GPIO_PERIPH_B, 0);
+	at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_MOSI,
+			   GPIO_PERIPH_B, 0);
+
+	/* reserve all other needed gpio
+	 * We have on board pull ups, so there is no need
+	 * to enable gpio pull ups */
+	/* INIT_DONE (input) */
+	at32_select_gpio(GPIO_PIN_PB(0), 0);
+
+	/* nSTATUS (input) */
+	at32_select_gpio(GPIO_PIN_PB(2), 0);
+
+	/* nCONFIG (output, low) */
+	at32_select_gpio(GPIO_PIN_PB(3), AT32_GPIOF_OUTPUT);
+
+	/* CONF_DONE (input) */
+	at32_select_gpio(GPIO_PIN_PB(4), 0);
+
+	/* Select EXTINT3 for PB28 (Interrupt from FPGA) */
+	at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_EXTINT3,
+			   GPIO_PERIPH_A, 0);
+
+	/* Get our parent clock */
+	hh_fpga0_spi_clk.parent = clk_get(NULL, "pba");
+	clk_put(hh_fpga0_spi_clk.parent);
+
+	/* Register clock in at32 clock tree */
+	at32_clk_register(&hh_fpga0_spi_clk);
+
+	platform_device_register(&hh_fpga0_device);
+	return &hh_fpga0_device;
+}
+#endif
+
+/* This needs to be called after the SMC has been initialized */
+static int __init hammerhead_flash_init(void)
+{
+	int ret;
+
+	smc_set_timing(&flash_config, &flash_timing);
+	ret = smc_set_configuration(0, &flash_config);
+
+	if (ret < 0) {
+		printk(KERN_ERR "hammerhead: failed to set NOR flash timing\n");
+		return ret;
+	}
+
+	platform_device_register(&flash_device);
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_USB
+	hammerhead_usbh_init();
+#endif
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
+	/* Setup SMC for FPGA interface */
+	smc_set_timing(&fpga_config, &fpga_timing);
+	ret = smc_set_configuration(3, &fpga_config);
+#endif
+
+
+	if (ret < 0) {
+		printk(KERN_ERR "hammerhead: failed to set FPGA timing\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+device_initcall(hammerhead_flash_init);

arch/avr32/boards/hammerhead/flash.h

@@ -0,0 +1,6 @@
+#ifndef __BOARDS_HAMMERHEAD_FLASH_H
+#define __BOARDS_HAMMERHEAD_FLASH_H
+
+struct platform_device *at32_add_device_hh_fpga(void);
+
+#endif /* __BOARDS_HAMMERHEAD_FLASH_H */

arch/avr32/boards/hammerhead/setup.c

@@ -0,0 +1,245 @@
+/*
+ * Board-specific setup code for the Miromico Hammerhead board
+ *
+ * Copyright (C) 2008 Miromico AG
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/atmel-mci.h>
+#include <linux/clk.h>
+#include <linux/fb.h>
+#include <linux/etherdevice.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <linux/init.h>
+#include <linux/linkage.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/spi/spi.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <linux/io.h>
+#include <asm/setup.h>
+
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
+
+#include "../../mach-at32ap/clock.h"
+#include "flash.h"
+
+/* Oscillator frequencies. These are board-specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 25000000, /* 25MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
+
+/* Initialized by bootloader-specific startup code. */
+struct tag *bootloader_tags __initdata;
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_LCD
+static struct fb_videomode __initdata hda350tlv_modes[] = {
+	{
+		.name		= "320x240 @ 75",
+		.refresh	= 75,
+		.xres		= 320,
+		.yres		= 240,
+		.pixclock	= KHZ2PICOS(6891),
+
+		.left_margin	= 48,
+		.right_margin	= 18,
+		.upper_margin	= 18,
+		.lower_margin	= 4,
+		.hsync_len	= 20,
+		.vsync_len	= 2,
+
+		.sync		= 0,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+};
+
+static struct fb_monspecs __initdata hammerhead_hda350t_monspecs = {
+	.manufacturer		= "HAN",
+	.monitor		= "HDA350T-LV",
+	.modedb			= hda350tlv_modes,
+	.modedb_len		= ARRAY_SIZE(hda350tlv_modes),
+	.hfmin			= 14900,
+	.hfmax			= 22350,
+	.vfmin			= 60,
+	.vfmax			= 90,
+	.dclkmax		= 10000000,
+};
+
+struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
+	.default_bpp		= 24,
+	.default_dmacon		= ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
+	.default_lcdcon2	= (ATMEL_LCDC_DISTYPE_TFT
+				   | ATMEL_LCDC_INVCLK
+				   | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
+				   | ATMEL_LCDC_MEMOR_BIG),
+	.default_monspecs	= &hammerhead_hda350t_monspecs,
+	.guard_time		= 2,
+};
+#endif
+
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+
+struct eth_addr {
+	u8 addr[6];
+};
+
+static struct eth_addr __initdata hw_addr[1];
+static struct eth_platform_data __initdata eth_data[1];
+
+/*
+ * The next two functions should go away as the boot loader is
+ * supposed to initialize the macb address registers with a valid
+ * ethernet address. But we need to keep it around for a while until
+ * we can be reasonably sure the boot loader does this.
+ *
+ * The phy_id is ignored as the driver will probe for it.
+ */
+static int __init parse_tag_ethernet(struct tag *tag)
+{
+	int i = tag->u.ethernet.mac_index;
+
+	if (i < ARRAY_SIZE(hw_addr))
+		memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
+		       sizeof(hw_addr[i].addr));
+
+	return 0;
+}
+__tagtable(ATAG_ETHERNET, parse_tag_ethernet);
+
+static void __init set_hw_addr(struct platform_device *pdev)
+{
+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	const u8 *addr;
+	void __iomem *regs;
+	struct clk *pclk;
+
+	if (!res)
+		return;
+
+	if (pdev->id >= ARRAY_SIZE(hw_addr))
+		return;
+
+	addr = hw_addr[pdev->id].addr;
+
+	if (!is_valid_ether_addr(addr))
+		return;
+
+	/*
+	 * Since this is board-specific code, we'll cheat and use the
+	 * physical address directly as we happen to know that it's
+	 * the same as the virtual address.
+	 */
+	regs = (void __iomem __force *)res->start;
+	pclk = clk_get(&pdev->dev, "pclk");
+
+	if (!pclk)
+		return;
+
+	clk_enable(pclk);
+
+	__raw_writel((addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) |
+		     addr[0], regs + 0x98);
+	__raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
+
+	clk_disable(pclk);
+	clk_put(pclk);
+}
+
+void __init setup_board(void)
+{
+	at32_map_usart(1, 0);	/* USART 1: /dev/ttyS0, DB9 */
+	at32_setup_serial_console(0);
+}
+
+static struct i2c_gpio_platform_data i2c_gpio_data = {
+	.sda_pin		= GPIO_PIN_PA(6),
+	.scl_pin		= GPIO_PIN_PA(7),
+	.sda_is_open_drain	= 1,
+	.scl_is_open_drain	= 1,
+	.udelay			= 2,	/* close to 100 kHz */
+};
+
+static struct platform_device i2c_gpio_device = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev		= { .platform_data = &i2c_gpio_data, },
+};
+
+static struct i2c_board_info __initdata i2c_info[] = {};
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_SND
+static struct ac97c_platform_data ac97c_data = {
+	.reset_pin = GPIO_PIN_PA(16),
+};
+#endif
+
+static int __init hammerhead_init(void)
+{
+	/*
+	 * Hammerhead uses 32-bit SDRAM interface. Reserve the
+	 * SDRAM-specific pins so that nobody messes with them.
+	 */
+	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
+
+	at32_add_device_usart(0);
+
+	/* Reserve PB29 (GCLK3). This pin is used as clock source
+	 * for ETH PHY (25MHz). GCLK3 setup is done by U-Boot.
+	 */
+	at32_reserve_pin(GPIO_PIOB_BASE, (1<<29));
+
+	/*
+	 * Hammerhead uses only one ethernet port, so we don't set
+	 * address of second port
+	 */
+	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
+	at32_add_device_hh_fpga();
+#endif
+	at32_add_device_mci(0, &mci0_data);
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_USB
+	at32_add_device_usba(0, NULL);
+#endif
+#ifdef CONFIG_BOARD_HAMMERHEAD_LCD
+	at32_add_device_lcdc(0, &hammerhead_lcdc_data, fbmem_start,
+			     fbmem_size, ATMEL_LCDC_PRI_24BIT);
+#endif
+
+	at32_select_gpio(i2c_gpio_data.sda_pin,
+			 AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT |
+			 AT32_GPIOF_HIGH);
+	at32_select_gpio(i2c_gpio_data.scl_pin,
+			 AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT |
+			 AT32_GPIOF_HIGH);
+	platform_device_register(&i2c_gpio_device);
+	i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
+
+#ifdef CONFIG_BOARD_HAMMERHEAD_SND
+	at32_add_device_ac97c(0, &ac97c_data);
+#endif
+
+	/* Select the Touchscreen interrupt pin mode */
+	at32_select_periph(GPIO_PIOB_BASE, 0x08000000, GPIO_PERIPH_A, 0);
+
+	return 0;
+}
+
+postcore_initcall(hammerhead_init);

arch/avr32/boards/mimc200/setup.c

@@ -24,7 +24,7 @@ extern struct atmel_lcdfb_info mimc200_lcdc_data;
 #include <video/atmel_lcdc.h>
 #include <linux/fb.h>
 
-#include <asm/atmel-mci.h>
+#include <linux/atmel-mci.h>
 #include <linux/io.h>
 #include <asm/setup.h>
 
@@ -207,8 +207,6 @@ static int __init mimc200_init(void)
 	 * reserve any pins for it.
 	 */
 
-	at32_add_system_devices();
-
 	at32_add_device_usart(0);
 	at32_add_device_usart(1);
 	at32_add_device_usart(2);

arch/avr32/configs/atngw100_defconfig

@@ -892,7 +892,7 @@ CONFIG_DMA_ENGINE=y
 # DMA Clients
 #
 # CONFIG_NET_DMA is not set
-CONFIG_DMATEST=m
+# CONFIG_DMATEST is not set
 # CONFIG_UIO is not set
 
 #

arch/avr32/configs/atstk1002_defconfig

@@ -964,7 +964,7 @@ CONFIG_DMA_ENGINE=y
 # DMA Clients
 #
 # CONFIG_NET_DMA is not set
-CONFIG_DMATEST=m
+# CONFIG_DMATEST is not set
 # CONFIG_UIO is not set
 
 #

arch/avr32/configs/atstk1003_defconfig

@@ -882,7 +882,7 @@ CONFIG_DMA_ENGINE=y
 # DMA Clients
 #
 # CONFIG_NET_DMA is not set
-CONFIG_DMATEST=m
+# CONFIG_DMATEST is not set
 # CONFIG_UIO is not set
 
 #

arch/avr32/configs/atstk1006_defconfig

@@ -1014,7 +1014,7 @@ CONFIG_DMA_ENGINE=y
 # DMA Clients
 #
 # CONFIG_NET_DMA is not set
-CONFIG_DMATEST=m
+# CONFIG_DMATEST is not set
 # CONFIG_UIO is not set
 # CONFIG_STAGING is not set
 CONFIG_STAGING_EXCLUDE_BUILD=y

arch/avr32/include/asm/kdebug.h

@@ -6,6 +6,7 @@ enum die_val {
 	DIE_BREAKPOINT,
 	DIE_SSTEP,
 	DIE_NMI,
+	DIE_OOPS,
 };
 
 #endif /* __ASM_AVR32_KDEBUG_H */

arch/avr32/include/asm/syscalls.h

@@ -0,0 +1,39 @@
+/*
+ * syscalls.h - Linux syscall interfaces (arch-specific)
+ *
+ * Copyright (c) 2008 Jaswinder Singh
+ *
+ * This file is released under the GPLv2.
+ * See the file COPYING for more details.
+ */
+
+#ifndef _ASM_AVR32_SYSCALLS_H
+#define _ASM_AVR32_SYSCALLS_H
+
+#include <linux/compiler.h>
+#include <linux/linkage.h>
+#include <linux/types.h>
+#include <linux/signal.h>
+
+/* kernel/process.c */
+asmlinkage int sys_fork(struct pt_regs *);
+asmlinkage int sys_clone(unsigned long, unsigned long,
+			 unsigned long, unsigned long,
+			 struct pt_regs *);
+asmlinkage int sys_vfork(struct pt_regs *);
+asmlinkage int sys_execve(char __user *, char __user *__user *,
+			  char __user *__user *, struct pt_regs *);
+
+/* kernel/signal.c */
+asmlinkage int sys_sigaltstack(const stack_t __user *, stack_t __user *,
+			       struct pt_regs *);
+asmlinkage int sys_rt_sigreturn(struct pt_regs *);
+
+/* kernel/sys_avr32.c */
+asmlinkage long sys_mmap2(unsigned long, unsigned long, unsigned long,
+			  unsigned long, unsigned long, off_t);
+
+/* mm/cache.c */
+asmlinkage int sys_cacheflush(int, void __user *, size_t);
+
+#endif /* _ASM_AVR32_SYSCALLS_H */

arch/avr32/kernel/process.c

@@ -18,6 +18,7 @@
 
 #include <asm/sysreg.h>
 #include <asm/ocd.h>
+#include <asm/syscalls.h>
 
 #include <mach/pm.h>
 

arch/avr32/kernel/signal.c

@@ -19,6 +19,7 @@
 
 #include <asm/uaccess.h>
 #include <asm/ucontext.h>
+#include <asm/syscalls.h>
 
 #define _BLOCKABLE (~(sigmask(SIGKILL) | sigmask(SIGSTOP)))
 

arch/avr32/kernel/sys_avr32.c

@@ -13,6 +13,7 @@
 
 #include <asm/mman.h>
 #include <asm/uaccess.h>
+#include <asm/syscalls.h>
 
 asmlinkage long sys_mmap2(unsigned long addr, unsigned long len,
 			  unsigned long prot, unsigned long flags,

arch/avr32/mach-at32ap/at32ap700x.c

@@ -15,8 +15,8 @@
 #include <linux/gpio.h>
 #include <linux/spi/spi.h>
 #include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
 
-#include <asm/atmel-mci.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 
@@ -421,7 +421,7 @@ static unsigned long hsb_clk_get_rate(struct clk *clk)
 	return bus_clk_get_rate(clk, shift);
 }
 
-static void pba_clk_mode(struct clk *clk, int enabled)
+void pba_clk_mode(struct clk *clk, int enabled)
 {
 	unsigned long flags;
 	u32 mask;
@@ -436,7 +436,7 @@ static void pba_clk_mode(struct clk *clk, int enabled)
 	spin_unlock_irqrestore(&pm_lock, flags);
 }
 
-static unsigned long pba_clk_get_rate(struct clk *clk)
+unsigned long pba_clk_get_rate(struct clk *clk)
 {
 	unsigned long cksel, shift = 0;
 

arch/avr32/mach-at32ap/clock.h

@@ -30,3 +30,6 @@ struct clk {
 	u16		users;		/* Enabled if non-zero */
 	u16		index;		/* Sibling index */
 };
+
+unsigned long pba_clk_get_rate(struct clk *clk);
+void pba_clk_mode(struct clk *clk, int enabled);

arch/avr32/mach-at32ap/include/mach/at32ap700x.h

@@ -211,4 +211,7 @@
 
 #define ATMEL_LCDC_ALT_15BIT	(ATMEL_LCDC_CONTROL | ATMEL_LCDC_ALT_15B_DATA)
 
+/* Bitmask for all EBI data (D16..D31) pins on port E */
+#define ATMEL_EBI_PE_DATA_ALL  (0x0000FFFF)
+
 #endif /* __ASM_ARCH_AT32AP700X_H__ */

arch/avr32/mach-at32ap/include/mach/portmux.h

@@ -25,6 +25,6 @@ void at32_select_periph(unsigned int port, unsigned int pin,
 			unsigned int periph, unsigned long flags);
 void at32_select_gpio(unsigned int pin, unsigned long flags);
 void at32_deselect_pin(unsigned int pin);
-void at32_reserve_pin(unsigned int pin);
+void at32_reserve_pin(unsigned int port, u32 pin_mask);
 
 #endif /* __ASM_ARCH_PORTMUX_H__ */

arch/avr32/mach-at32ap/pio.c

@@ -167,22 +167,29 @@ void at32_deselect_pin(unsigned int pin)
 }
 
 /* Reserve a pin, preventing anyone else from changing its configuration. */
-void __init at32_reserve_pin(unsigned int pin)
+void __init at32_reserve_pin(unsigned int port, u32 pin_mask)
 {
 	struct pio_device *pio;
-	unsigned int pin_index = pin & 0x1f;
 
-	pio = gpio_to_pio(pin);
+	/* assign and verify pio */
+	pio = gpio_to_pio(port);
 	if (unlikely(!pio)) {
-		printk("pio: invalid pin %u\n", pin);
+		printk(KERN_WARNING "pio: invalid port %u\n", port);
 		goto fail;
 	}
 
-	if (unlikely(test_and_set_bit(pin_index, &pio->pinmux_mask))) {
+	/* Test if any of the requested pins is already muxed */
-		printk("%s: pin %u is busy\n", pio->name, pin_index);
+	spin_lock(&pio_lock);
+	if (unlikely(pio->pinmux_mask & pin_mask)) {
+		printk(KERN_WARNING "%s: pin(s) busy (req. 0x%x, busy 0x%x)\n",
+		       pio->name, pin_mask, pio->pinmux_mask & pin_mask);
+		spin_unlock(&pio_lock);
 		goto fail;
 	}
 
+	/* Reserve pins */
+	pio->pinmux_mask |= pin_mask;
+	spin_unlock(&pio_lock);
 	return;
 
 fail:

arch/avr32/mm/cache.c

@@ -13,6 +13,7 @@
 #include <asm/cachectl.h>
 #include <asm/processor.h>
 #include <asm/uaccess.h>
+#include <asm/syscalls.h>
 
 /*
  * If you attempt to flush anything more than this, you need superuser

arch/avr32/mm/init.c

@@ -97,7 +97,6 @@ void __init paging_init(void)
 
 	mem_map = NODE_DATA(0)->node_mem_map;
 
-	memset(zero_page, 0, PAGE_SIZE);
 	empty_zero_page = virt_to_page(zero_page);
 	flush_dcache_page(empty_zero_page);
 }

drivers/mmc/host/atmel-mci.c

@@ -25,8 +25,8 @@
 #include <linux/stat.h>
 
 #include <linux/mmc/host.h>
+#include <linux/atmel-mci.h>
 
-#include <asm/atmel-mci.h>
 #include <asm/io.h>
 #include <asm/unaligned.h>
 

include/linux/atmel-mci.h

@@ -1,5 +1,5 @@
-#ifndef __ASM_AVR32_ATMEL_MCI_H
+#ifndef __LINUX_ATMEL_MCI_H
-#define __ASM_AVR32_ATMEL_MCI_H
+#define __LINUX_ATMEL_MCI_H
 
 #define ATMEL_MCI_MAX_NR_SLOTS	2
 
@@ -36,4 +36,4 @@ struct mci_platform_data {
 	struct mci_slot_pdata	slot[ATMEL_MCI_MAX_NR_SLOTS];
 };
 
-#endif /* __ASM_AVR32_ATMEL_MCI_H */
+#endif /* __LINUX_ATMEL_MCI_H */