From 281e8b2fdf8e4ef366b899453cae50e09b577ada Mon Sep 17 00:00:00 2001 From: Amir Vadai Date: Wed, 17 Feb 2016 17:24:22 +0200 Subject: [PATCH 1/6] net/mlx4_en: Count HW buffer overrun only once RdropOvflw counts overrun of HW buffer, therefore should be used for rx_fifo_errors only. Currently RdropOvflw counter is mistakenly also set into rx_missed_errors and rx_over_errors too, which makes the device total dropped packets accounting to show wrong results. Fix that. Use it for rx_fifo_errors only. Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC') Signed-off-by: Amir Vadai Signed-off-by: Eugenia Emantayev Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_port.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlx4/en_port.c b/drivers/net/ethernet/mellanox/mlx4/en_port.c index ee99e67187f5..3904b5fc0b7c 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_port.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_port.c @@ -238,11 +238,11 @@ int mlx4_en_DUMP_ETH_STATS(struct mlx4_en_dev *mdev, u8 port, u8 reset) stats->collisions = 0; stats->rx_dropped = be32_to_cpu(mlx4_en_stats->RDROP); stats->rx_length_errors = be32_to_cpu(mlx4_en_stats->RdropLength); - stats->rx_over_errors = be32_to_cpu(mlx4_en_stats->RdropOvflw); + stats->rx_over_errors = 0; stats->rx_crc_errors = be32_to_cpu(mlx4_en_stats->RCRC); stats->rx_frame_errors = 0; stats->rx_fifo_errors = be32_to_cpu(mlx4_en_stats->RdropOvflw); - stats->rx_missed_errors = be32_to_cpu(mlx4_en_stats->RdropOvflw); + stats->rx_missed_errors = 0; stats->tx_aborted_errors = 0; stats->tx_carrier_errors = 0; stats->tx_fifo_errors = 0; From 31c128b66e5b28f468076e4f3ca3025c35342041 Mon Sep 17 00:00:00 2001 From: Eugenia Emantayev Date: Wed, 17 Feb 2016 17:24:23 +0200 Subject: [PATCH 2/6] net/mlx4_en: Choose time-stamping shift value according to HW frequency Previously, the shift value used for time-stamping was constant and didn't depend on the HW chip frequency. Change that to take the frequency into account and calculate the maximal value in cycles per wraparound of ten seconds. This time slot was chosen since it gives a good accuracy in time synchronization. Algorithm for shift value calculation: * Round up the maximal value in cycles to nearest power of two * Calculate maximal multiplier by division of all 64 bits set to above result * Then, invert the function clocksource_khz2mult() to get the shift from maximal mult value Fixes: ec693d47010e ('net/mlx4_en: Add HW timestamping (TS) support') Signed-off-by: Eugenia Emantayev Reviewed-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_clock.c | 25 ++++++++++++++----- 1 file changed, 19 insertions(+), 6 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlx4/en_clock.c b/drivers/net/ethernet/mellanox/mlx4/en_clock.c index 038f9ce391e6..1494997c4f7e 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_clock.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_clock.c @@ -236,6 +236,24 @@ static const struct ptp_clock_info mlx4_en_ptp_clock_info = { .enable = mlx4_en_phc_enable, }; +#define MLX4_EN_WRAP_AROUND_SEC 10ULL + +/* This function calculates the max shift that enables the user range + * of MLX4_EN_WRAP_AROUND_SEC values in the cycles register. + */ +static u32 freq_to_shift(u16 freq) +{ + u32 freq_khz = freq * 1000; + u64 max_val_cycles = freq_khz * 1000 * MLX4_EN_WRAP_AROUND_SEC; + u64 max_val_cycles_rounded = is_power_of_2(max_val_cycles + 1) ? + max_val_cycles : roundup_pow_of_two(max_val_cycles) - 1; + /* calculate max possible multiplier in order to fit in 64bit */ + u64 max_mul = div_u64(0xffffffffffffffffULL, max_val_cycles_rounded); + + /* This comes from the reverse of clocksource_khz2mult */ + return ilog2(div_u64(max_mul * freq_khz, 1000000)); +} + void mlx4_en_init_timestamp(struct mlx4_en_dev *mdev) { struct mlx4_dev *dev = mdev->dev; @@ -254,12 +272,7 @@ void mlx4_en_init_timestamp(struct mlx4_en_dev *mdev) memset(&mdev->cycles, 0, sizeof(mdev->cycles)); mdev->cycles.read = mlx4_en_read_clock; mdev->cycles.mask = CLOCKSOURCE_MASK(48); - /* Using shift to make calculation more accurate. Since current HW - * clock frequency is 427 MHz, and cycles are given using a 48 bits - * register, the biggest shift when calculating using u64, is 14 - * (max_cycles * multiplier < 2^64) - */ - mdev->cycles.shift = 14; + mdev->cycles.shift = freq_to_shift(dev->caps.hca_core_clock); mdev->cycles.mult = clocksource_khz2mult(1000 * dev->caps.hca_core_clock, mdev->cycles.shift); mdev->nominal_c_mult = mdev->cycles.mult; From 6b94bab0ee8d5def6a2aac0ef6204ee6e24386b6 Mon Sep 17 00:00:00 2001 From: Eran Ben Elisha Date: Wed, 17 Feb 2016 17:24:24 +0200 Subject: [PATCH 3/6] net/mlx4_core: Fix potential corruption in counters database The error flow in procedure handle_existing_counter() is wrong. The procedure should exit after encountering the error, not continue as if everything is OK. Fixes: 68230242cdbc ('net/mlx4_core: Add port attribute when tracking counters') Signed-off-by: Eran Ben Elisha Signed-off-by: Jack Morgenstein Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/resource_tracker.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index b46dbe29ef6c..25ce1b030a00 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -915,11 +915,13 @@ static int handle_existing_counter(struct mlx4_dev *dev, u8 slave, int port, spin_lock_irq(mlx4_tlock(dev)); r = find_res(dev, counter_index, RES_COUNTER); - if (!r || r->owner != slave) + if (!r || r->owner != slave) { ret = -EINVAL; - counter = container_of(r, struct res_counter, com); - if (!counter->port) - counter->port = port; + } else { + counter = container_of(r, struct res_counter, com); + if (!counter->port) + counter->port = port; + } spin_unlock_irq(mlx4_tlock(dev)); return ret; From 22e3817e6c8301dc0520b855c8a2d764580e719c Mon Sep 17 00:00:00 2001 From: Daniel Jurgens Date: Wed, 17 Feb 2016 17:24:25 +0200 Subject: [PATCH 4/6] net/mlx4_core: Do not BUG_ON during reset when PCI is offline The PCI channel could go offline during reset due to EEH. Don't bug on in this case, the error is recoverable. Fixes: f6bc11e42646 ('net/mlx4_core: Enhance the catas flow to support device reset') Signed-off-by: Daniel Jurgens Reviewed-by: Yishai Hadas Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/catas.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlx4/catas.c b/drivers/net/ethernet/mellanox/mlx4/catas.c index 715de8affcc9..c7e939945259 100644 --- a/drivers/net/ethernet/mellanox/mlx4/catas.c +++ b/drivers/net/ethernet/mellanox/mlx4/catas.c @@ -182,10 +182,17 @@ void mlx4_enter_error_state(struct mlx4_dev_persistent *persist) err = mlx4_reset_slave(dev); else err = mlx4_reset_master(dev); - BUG_ON(err != 0); + if (!err) { + mlx4_err(dev, "device was reset successfully\n"); + } else { + /* EEH could have disabled the PCI channel during reset. That's + * recoverable and the PCI error flow will handle it. + */ + if (!pci_channel_offline(dev->persist->pdev)) + BUG_ON(1); + } dev->persist->state |= MLX4_DEVICE_STATE_INTERNAL_ERROR; - mlx4_err(dev, "device was reset successfully\n"); mutex_unlock(&persist->device_state_mutex); /* At that step HW was already reset, now notify clients */ From 85743f1eb34548ba4b056d2f184a3d107a3b8917 Mon Sep 17 00:00:00 2001 From: Huy Nguyen Date: Wed, 17 Feb 2016 17:24:26 +0200 Subject: [PATCH 5/6] net/mlx4_core: Set UAR page size to 4KB regardless of system page size problem description: The current code sets UAR page size equal to system page size. The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages. The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages. solution: Always set UAR page to 4KB. This allows more UAR pages if the OS has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB system page size, with 4MB uar region, there are 4MB/2/64KB = 32 uars (half for uar, half for blueflame). This does not meet minimum 128 UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars which meet the minimum requirement. Note that only codes in mlx4_core that deal with firmware know that uar page size is 4KB. Codes that deal with usr page in cq and qp context (mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption that uar page size equals to system page size. Note that with this implementation, on 64KB system page size kernel, there are 16 uars per system page but only one uars is used. The other 15 uars are ignored because of the above assumption. Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size to 4KB and mlx4_core code in virtual OS will obtain the uar page size from firmware. Regarding backward compatibility in SR-IOV, if hypervisor has this new code, the virtual OS must be updated. If hypervisor has old code, and the virtual OS has this new code, the new code will be backward compatible with the old code. If the uar size is big enough, this new code in VF continues to work with 64 KB uar page size (on PowerPc kernel). If the uar size does not meet 128 uars requirement, this new code not loaded in VF and print the same error message as the old code in Hypervisor. Signed-off-by: Huy Nguyen Reviewed-by: Yishai Hadas Signed-off-by: David S. Miller --- drivers/infiniband/hw/mlx4/qp.c | 7 ++- drivers/net/ethernet/mellanox/mlx4/cq.c | 4 +- .../net/ethernet/mellanox/mlx4/en_resources.c | 3 +- drivers/net/ethernet/mellanox/mlx4/en_tx.c | 4 +- drivers/net/ethernet/mellanox/mlx4/eq.c | 7 ++- drivers/net/ethernet/mellanox/mlx4/main.c | 56 +++++++++++++++---- drivers/net/ethernet/mellanox/mlx4/pd.c | 12 +++- include/linux/mlx4/device.h | 13 +++++ 8 files changed, 84 insertions(+), 22 deletions(-) diff --git a/drivers/infiniband/hw/mlx4/qp.c b/drivers/infiniband/hw/mlx4/qp.c index bc5536f00b6c..fd97534762b8 100644 --- a/drivers/infiniband/hw/mlx4/qp.c +++ b/drivers/infiniband/hw/mlx4/qp.c @@ -1681,9 +1681,12 @@ static int __mlx4_ib_modify_qp(struct ib_qp *ibqp, } if (qp->ibqp.uobject) - context->usr_page = cpu_to_be32(to_mucontext(ibqp->uobject->context)->uar.index); + context->usr_page = cpu_to_be32( + mlx4_to_hw_uar_index(dev->dev, + to_mucontext(ibqp->uobject->context)->uar.index)); else - context->usr_page = cpu_to_be32(dev->priv_uar.index); + context->usr_page = cpu_to_be32( + mlx4_to_hw_uar_index(dev->dev, dev->priv_uar.index)); if (attr_mask & IB_QP_DEST_QPN) context->remote_qpn = cpu_to_be32(attr->dest_qp_num); diff --git a/drivers/net/ethernet/mellanox/mlx4/cq.c b/drivers/net/ethernet/mellanox/mlx4/cq.c index 3348e646db70..a849da92f857 100644 --- a/drivers/net/ethernet/mellanox/mlx4/cq.c +++ b/drivers/net/ethernet/mellanox/mlx4/cq.c @@ -318,7 +318,9 @@ int mlx4_cq_alloc(struct mlx4_dev *dev, int nent, if (timestamp_en) cq_context->flags |= cpu_to_be32(1 << 19); - cq_context->logsize_usrpage = cpu_to_be32((ilog2(nent) << 24) | uar->index); + cq_context->logsize_usrpage = + cpu_to_be32((ilog2(nent) << 24) | + mlx4_to_hw_uar_index(dev, uar->index)); cq_context->comp_eqn = priv->eq_table.eq[MLX4_CQ_TO_EQ_VECTOR(vector)].eqn; cq_context->log_page_size = mtt->page_shift - MLX4_ICM_PAGE_SHIFT; diff --git a/drivers/net/ethernet/mellanox/mlx4/en_resources.c b/drivers/net/ethernet/mellanox/mlx4/en_resources.c index 12aab5a659d3..02e925d6f734 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_resources.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_resources.c @@ -58,7 +58,8 @@ void mlx4_en_fill_qp_context(struct mlx4_en_priv *priv, int size, int stride, } else { context->sq_size_stride = ilog2(TXBB_SIZE) - 4; } - context->usr_page = cpu_to_be32(mdev->priv_uar.index); + context->usr_page = cpu_to_be32(mlx4_to_hw_uar_index(mdev->dev, + mdev->priv_uar.index)); context->local_qpn = cpu_to_be32(qpn); context->pri_path.ackto = 1 & 0x07; context->pri_path.sched_queue = 0x83 | (priv->port - 1) << 6; diff --git a/drivers/net/ethernet/mellanox/mlx4/en_tx.c b/drivers/net/ethernet/mellanox/mlx4/en_tx.c index 4421bf5463f6..e0946ab22010 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_tx.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_tx.c @@ -213,7 +213,9 @@ int mlx4_en_activate_tx_ring(struct mlx4_en_priv *priv, mlx4_en_fill_qp_context(priv, ring->size, ring->stride, 1, 0, ring->qpn, ring->cqn, user_prio, &ring->context); if (ring->bf_alloced) - ring->context.usr_page = cpu_to_be32(ring->bf.uar->index); + ring->context.usr_page = + cpu_to_be32(mlx4_to_hw_uar_index(mdev->dev, + ring->bf.uar->index)); err = mlx4_qp_to_ready(mdev->dev, &ring->wqres.mtt, &ring->context, &ring->qp, &ring->qp_state); diff --git a/drivers/net/ethernet/mellanox/mlx4/eq.c b/drivers/net/ethernet/mellanox/mlx4/eq.c index 4696053165f8..f613977455e0 100644 --- a/drivers/net/ethernet/mellanox/mlx4/eq.c +++ b/drivers/net/ethernet/mellanox/mlx4/eq.c @@ -940,9 +940,10 @@ static void __iomem *mlx4_get_eq_uar(struct mlx4_dev *dev, struct mlx4_eq *eq) if (!priv->eq_table.uar_map[index]) { priv->eq_table.uar_map[index] = - ioremap(pci_resource_start(dev->persist->pdev, 2) + - ((eq->eqn / 4) << PAGE_SHIFT), - PAGE_SIZE); + ioremap( + pci_resource_start(dev->persist->pdev, 2) + + ((eq->eqn / 4) << (dev->uar_page_shift)), + (1 << (dev->uar_page_shift))); if (!priv->eq_table.uar_map[index]) { mlx4_err(dev, "Couldn't map EQ doorbell for EQN 0x%06x\n", eq->eqn); diff --git a/drivers/net/ethernet/mellanox/mlx4/main.c b/drivers/net/ethernet/mellanox/mlx4/main.c index f1b6d219e445..2cc3c626c3fe 100644 --- a/drivers/net/ethernet/mellanox/mlx4/main.c +++ b/drivers/net/ethernet/mellanox/mlx4/main.c @@ -168,6 +168,20 @@ struct mlx4_port_config { static atomic_t pf_loading = ATOMIC_INIT(0); +static inline void mlx4_set_num_reserved_uars(struct mlx4_dev *dev, + struct mlx4_dev_cap *dev_cap) +{ + /* The reserved_uars is calculated by system page size unit. + * Therefore, adjustment is added when the uar page size is less + * than the system page size + */ + dev->caps.reserved_uars = + max_t(int, + mlx4_get_num_reserved_uar(dev), + dev_cap->reserved_uars / + (1 << (PAGE_SHIFT - dev->uar_page_shift))); +} + int mlx4_check_port_params(struct mlx4_dev *dev, enum mlx4_port_type *port_type) { @@ -386,8 +400,6 @@ static int mlx4_dev_cap(struct mlx4_dev *dev, struct mlx4_dev_cap *dev_cap) dev->caps.reserved_mtts = dev_cap->reserved_mtts; dev->caps.reserved_mrws = dev_cap->reserved_mrws; - /* The first 128 UARs are used for EQ doorbells */ - dev->caps.reserved_uars = max_t(int, 128, dev_cap->reserved_uars); dev->caps.reserved_pds = dev_cap->reserved_pds; dev->caps.reserved_xrcds = (dev->caps.flags & MLX4_DEV_CAP_FLAG_XRC) ? dev_cap->reserved_xrcds : 0; @@ -405,6 +417,15 @@ static int mlx4_dev_cap(struct mlx4_dev *dev, struct mlx4_dev_cap *dev_cap) dev->caps.max_gso_sz = dev_cap->max_gso_sz; dev->caps.max_rss_tbl_sz = dev_cap->max_rss_tbl_sz; + /* Save uar page shift */ + if (!mlx4_is_slave(dev)) { + /* Virtual PCI function needs to determine UAR page size from + * firmware. Only master PCI function can set the uar page size + */ + dev->uar_page_shift = DEFAULT_UAR_PAGE_SHIFT; + mlx4_set_num_reserved_uars(dev, dev_cap); + } + if (dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_PHV_EN) { struct mlx4_init_hca_param hca_param; @@ -815,16 +836,25 @@ static int mlx4_slave_cap(struct mlx4_dev *dev) return -ENODEV; } - /* slave gets uar page size from QUERY_HCA fw command */ - dev->caps.uar_page_size = 1 << (hca_param.uar_page_sz + 12); + /* Set uar_page_shift for VF */ + dev->uar_page_shift = hca_param.uar_page_sz + 12; - /* TODO: relax this assumption */ - if (dev->caps.uar_page_size != PAGE_SIZE) { - mlx4_err(dev, "UAR size:%d != kernel PAGE_SIZE of %ld\n", - dev->caps.uar_page_size, PAGE_SIZE); - return -ENODEV; + /* Make sure the master uar page size is valid */ + if (dev->uar_page_shift > PAGE_SHIFT) { + mlx4_err(dev, + "Invalid configuration: uar page size is larger than system page size\n"); + return -ENODEV; } + /* Set reserved_uars based on the uar_page_shift */ + mlx4_set_num_reserved_uars(dev, &dev_cap); + + /* Although uar page size in FW differs from system page size, + * upper software layers (mlx4_ib, mlx4_en and part of mlx4_core) + * still works with assumption that uar page size == system page size + */ + dev->caps.uar_page_size = PAGE_SIZE; + memset(&func_cap, 0, sizeof(func_cap)); err = mlx4_QUERY_FUNC_CAP(dev, 0, &func_cap); if (err) { @@ -2179,8 +2209,12 @@ static int mlx4_init_hca(struct mlx4_dev *dev) dev->caps.max_fmr_maps = (1 << (32 - ilog2(dev->caps.num_mpts))) - 1; - init_hca.log_uar_sz = ilog2(dev->caps.num_uars); - init_hca.uar_page_sz = PAGE_SHIFT - 12; + /* Always set UAR page size 4KB, set log_uar_sz accordingly */ + init_hca.log_uar_sz = ilog2(dev->caps.num_uars) + + PAGE_SHIFT - + DEFAULT_UAR_PAGE_SHIFT; + init_hca.uar_page_sz = DEFAULT_UAR_PAGE_SHIFT - 12; + init_hca.mw_enabled = 0; if (dev->caps.flags & MLX4_DEV_CAP_FLAG_MEM_WINDOW || dev->caps.bmme_flags & MLX4_BMME_FLAG_TYPE_2_WIN) diff --git a/drivers/net/ethernet/mellanox/mlx4/pd.c b/drivers/net/ethernet/mellanox/mlx4/pd.c index 609c59dc854e..b3cc3ab63799 100644 --- a/drivers/net/ethernet/mellanox/mlx4/pd.c +++ b/drivers/net/ethernet/mellanox/mlx4/pd.c @@ -269,9 +269,15 @@ EXPORT_SYMBOL_GPL(mlx4_bf_free); int mlx4_init_uar_table(struct mlx4_dev *dev) { - if (dev->caps.num_uars <= 128) { - mlx4_err(dev, "Only %d UAR pages (need more than 128)\n", - dev->caps.num_uars); + int num_reserved_uar = mlx4_get_num_reserved_uar(dev); + + mlx4_dbg(dev, "uar_page_shift = %d", dev->uar_page_shift); + mlx4_dbg(dev, "Effective reserved_uars=%d", dev->caps.reserved_uars); + + if (dev->caps.num_uars <= num_reserved_uar) { + mlx4_err( + dev, "Only %d UAR pages (need more than %d)\n", + dev->caps.num_uars, num_reserved_uar); mlx4_err(dev, "Increase firmware log2_uar_bar_megabytes?\n"); return -ENODEV; } diff --git a/include/linux/mlx4/device.h b/include/linux/mlx4/device.h index 430a929f048b..a0e8cc8dcc67 100644 --- a/include/linux/mlx4/device.h +++ b/include/linux/mlx4/device.h @@ -44,6 +44,8 @@ #include +#define DEFAULT_UAR_PAGE_SHIFT 12 + #define MAX_MSIX_P_PORT 17 #define MAX_MSIX 64 #define MIN_MSIX_P_PORT 5 @@ -856,6 +858,7 @@ struct mlx4_dev { u64 regid_promisc_array[MLX4_MAX_PORTS + 1]; u64 regid_allmulti_array[MLX4_MAX_PORTS + 1]; struct mlx4_vf_dev *dev_vfs; + u8 uar_page_shift; }; struct mlx4_clock_params { @@ -1528,4 +1531,14 @@ int mlx4_ACCESS_PTYS_REG(struct mlx4_dev *dev, int mlx4_get_internal_clock_params(struct mlx4_dev *dev, struct mlx4_clock_params *params); +static inline int mlx4_to_hw_uar_index(struct mlx4_dev *dev, int index) +{ + return (index << (PAGE_SHIFT - dev->uar_page_shift)); +} + +static inline int mlx4_get_num_reserved_uar(struct mlx4_dev *dev) +{ + /* The first 128 UARs are used for EQ doorbells */ + return (128 >> (PAGE_SHIFT - dev->uar_page_shift)); +} #endif /* MLX4_DEVICE_H */ From 925ab1aa9394bbaeac47ee5b65d3fdf0fb8135cf Mon Sep 17 00:00:00 2001 From: Eugenia Emantayev Date: Wed, 17 Feb 2016 17:24:27 +0200 Subject: [PATCH 6/6] net/mlx4_en: Avoid changing dev->features directly in run-time It's forbidden to manually change dev->features in run-time. Currently, this is done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when VXLAN tunnel is set. However, since the stack actually does features intersection with hw_enc_features, we can safely revert to advertizing features early when registering the netdevice. Fixes: f4a1edd56120 ('net/mlx4_en: Advertize encapsulation offloads [...]') Signed-off-by: Eugenia Emantayev Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c index 0c7e3f69a73b..f191a1612589 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c @@ -2344,8 +2344,6 @@ static void mlx4_en_add_vxlan_offloads(struct work_struct *work) /* set offloads */ priv->dev->hw_enc_features |= NETIF_F_IP_CSUM | NETIF_F_RXCSUM | NETIF_F_TSO | NETIF_F_GSO_UDP_TUNNEL; - priv->dev->hw_features |= NETIF_F_GSO_UDP_TUNNEL; - priv->dev->features |= NETIF_F_GSO_UDP_TUNNEL; } static void mlx4_en_del_vxlan_offloads(struct work_struct *work) @@ -2356,8 +2354,6 @@ static void mlx4_en_del_vxlan_offloads(struct work_struct *work) /* unset offloads */ priv->dev->hw_enc_features &= ~(NETIF_F_IP_CSUM | NETIF_F_RXCSUM | NETIF_F_TSO | NETIF_F_GSO_UDP_TUNNEL); - priv->dev->hw_features &= ~NETIF_F_GSO_UDP_TUNNEL; - priv->dev->features &= ~NETIF_F_GSO_UDP_TUNNEL; ret = mlx4_SET_PORT_VXLAN(priv->mdev->dev, priv->port, VXLAN_STEER_BY_OUTER_MAC, 0); @@ -2980,6 +2976,11 @@ int mlx4_en_init_netdev(struct mlx4_en_dev *mdev, int port, priv->rss_hash_fn = ETH_RSS_HASH_TOP; } + if (mdev->dev->caps.tunnel_offload_mode == MLX4_TUNNEL_OFFLOAD_MODE_VXLAN) { + dev->hw_features |= NETIF_F_GSO_UDP_TUNNEL; + dev->features |= NETIF_F_GSO_UDP_TUNNEL; + } + mdev->pndev[port] = dev; mdev->upper[port] = NULL;