ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board

This is an H3-based board that sticks close to the reference design.

Supported features:
* UART
* DRAM
* MMC
* eMMC
* Ethernet
* USB host
* USB peripheral
* HDMI

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arch/arm/boot/dts/Makefile

@@ -1091,6 +1091,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-orangepi-plus.dtb \
 	sun8i-h3-orangepi-plus2e.dtb \
 	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-rervision-dvk.dtb \
 	sun8i-r16-bananapi-m2m.dtb \
 	sun8i-r16-nintendo-nes-classic.dtb \
 	sun8i-r16-nintendo-super-nes-classic.dtb \

arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts

@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Bootlin
+ * Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "RerVision H3-DVK";
+	compatible = "rervision,h3-dvk", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usbphy {
+	status = "okay";
+};