mirror of https://gitee.com/openkylin/linux.git
Merge branch 'for-rmk/broadcast' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into devel-stable
This commit is contained in:
commit
2fb20e2e35
|
@ -141,3 +141,4 @@ Version History
|
|||
1.2.0 Handle creation of arrays that contain failed devices.
|
||||
1.3.0 Added support for RAID 10
|
||||
1.3.1 Allow device replacement/rebuild for RAID 10
|
||||
1.3.2 Fix/improve redundancy checking for RAID10
|
||||
|
|
|
@ -81,7 +81,8 @@ PA31 TXD4
|
|||
Required properties for pin configuration node:
|
||||
- atmel,pins: 4 integers array, represents a group of pins mux and config
|
||||
setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
|
||||
The PERIPH 0 means gpio.
|
||||
The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
|
||||
PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
|
||||
|
||||
Bits used for CONFIG:
|
||||
PULL_UP (1 << 0): indicate this pin need a pull up.
|
||||
|
@ -126,7 +127,7 @@ pinctrl@fffff400 {
|
|||
pinctrl_dbgu: dbgu-0 {
|
||||
atmel,pins =
|
||||
<1 14 0x1 0x0 /* PB14 periph A */
|
||||
1 15 0x1 0x1>; /* PB15 periph with pullup */
|
||||
1 15 0x1 0x1>; /* PB15 periph A with pullup */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
|
@ -175,9 +175,9 @@ consists of multiple segments as described below.
|
|||
align with the zone size <-|
|
||||
|-> align with the segment size
|
||||
_________________________________________________________________________
|
||||
| | | Node | Segment | Segment | |
|
||||
| Superblock | Checkpoint | Address | Info. | Summary | Main |
|
||||
| (SB) | (CP) | Table (NAT) | Table (SIT) | Area (SSA) | |
|
||||
| | | Segment | Node | Segment | |
|
||||
| Superblock | Checkpoint | Info. | Address | Summary | Main |
|
||||
| (SB) | (CP) | Table (SIT) | Table (NAT) | Area (SSA) | |
|
||||
|____________|_____2______|______N______|______N______|______N_____|__N___|
|
||||
. .
|
||||
. .
|
||||
|
@ -200,14 +200,14 @@ consists of multiple segments as described below.
|
|||
: It contains file system information, bitmaps for valid NAT/SIT sets, orphan
|
||||
inode lists, and summary entries of current active segments.
|
||||
|
||||
- Node Address Table (NAT)
|
||||
: It is composed of a block address table for all the node blocks stored in
|
||||
Main area.
|
||||
|
||||
- Segment Information Table (SIT)
|
||||
: It contains segment information such as valid block count and bitmap for the
|
||||
validity of all the blocks.
|
||||
|
||||
- Node Address Table (NAT)
|
||||
: It is composed of a block address table for all the node blocks stored in
|
||||
Main area.
|
||||
|
||||
- Segment Summary Area (SSA)
|
||||
: It contains summary entries which contains the owner information of all the
|
||||
data and node blocks stored in Main area.
|
||||
|
@ -236,13 +236,13 @@ For file system consistency, each CP points to which NAT and SIT copies are
|
|||
valid, as shown as below.
|
||||
|
||||
+--------+----------+---------+
|
||||
| CP | NAT | SIT |
|
||||
| CP | SIT | NAT |
|
||||
+--------+----------+---------+
|
||||
. . . .
|
||||
. . . .
|
||||
. . . .
|
||||
+-------+-------+--------+--------+--------+--------+
|
||||
| CP #0 | CP #1 | NAT #0 | NAT #1 | SIT #0 | SIT #1 |
|
||||
| CP #0 | CP #1 | SIT #0 | SIT #1 | NAT #0 | NAT #1 |
|
||||
+-------+-------+--------+--------+--------+--------+
|
||||
| ^ ^
|
||||
| | |
|
||||
|
|
|
@ -57,6 +57,10 @@ Protocol 2.10: (Kernel 2.6.31) Added a protocol for relaxed alignment
|
|||
Protocol 2.11: (Kernel 3.6) Added a field for offset of EFI handover
|
||||
protocol entry point.
|
||||
|
||||
Protocol 2.12: (Kernel 3.9) Added the xloadflags field and extension fields
|
||||
to struct boot_params for for loading bzImage and ramdisk
|
||||
above 4G in 64bit.
|
||||
|
||||
**** MEMORY LAYOUT
|
||||
|
||||
The traditional memory map for the kernel loader, used for Image or
|
||||
|
@ -182,7 +186,7 @@ Offset Proto Name Meaning
|
|||
0230/4 2.05+ kernel_alignment Physical addr alignment required for kernel
|
||||
0234/1 2.05+ relocatable_kernel Whether kernel is relocatable or not
|
||||
0235/1 2.10+ min_alignment Minimum alignment, as a power of two
|
||||
0236/2 N/A pad3 Unused
|
||||
0236/2 2.12+ xloadflags Boot protocol option flags
|
||||
0238/4 2.06+ cmdline_size Maximum size of the kernel command line
|
||||
023C/4 2.07+ hardware_subarch Hardware subarchitecture
|
||||
0240/8 2.07+ hardware_subarch_data Subarchitecture-specific data
|
||||
|
@ -582,6 +586,27 @@ Protocol: 2.10+
|
|||
misaligned kernel. Therefore, a loader should typically try each
|
||||
power-of-two alignment from kernel_alignment down to this alignment.
|
||||
|
||||
Field name: xloadflags
|
||||
Type: read
|
||||
Offset/size: 0x236/2
|
||||
Protocol: 2.12+
|
||||
|
||||
This field is a bitmask.
|
||||
|
||||
Bit 0 (read): XLF_KERNEL_64
|
||||
- If 1, this kernel has the legacy 64-bit entry point at 0x200.
|
||||
|
||||
Bit 1 (read): XLF_CAN_BE_LOADED_ABOVE_4G
|
||||
- If 1, kernel/boot_params/cmdline/ramdisk can be above 4G.
|
||||
|
||||
Bit 2 (read): XLF_EFI_HANDOVER_32
|
||||
- If 1, the kernel supports the 32-bit EFI handoff entry point
|
||||
given at handover_offset.
|
||||
|
||||
Bit 3 (read): XLF_EFI_HANDOVER_64
|
||||
- If 1, the kernel supports the 64-bit EFI handoff entry point
|
||||
given at handover_offset + 0x200.
|
||||
|
||||
Field name: cmdline_size
|
||||
Type: read
|
||||
Offset/size: 0x238/4
|
||||
|
|
|
@ -19,6 +19,9 @@ Offset Proto Name Meaning
|
|||
090/010 ALL hd1_info hd1 disk parameter, OBSOLETE!!
|
||||
0A0/010 ALL sys_desc_table System description table (struct sys_desc_table)
|
||||
0B0/010 ALL olpc_ofw_header OLPC's OpenFirmware CIF and friends
|
||||
0C0/004 ALL ext_ramdisk_image ramdisk_image high 32bits
|
||||
0C4/004 ALL ext_ramdisk_size ramdisk_size high 32bits
|
||||
0C8/004 ALL ext_cmd_line_ptr cmd_line_ptr high 32bits
|
||||
140/080 ALL edid_info Video mode setup (struct edid_info)
|
||||
1C0/020 ALL efi_info EFI 32 information (struct efi_info)
|
||||
1E0/004 ALL alk_mem_k Alternative mem check, in KB
|
||||
|
@ -27,6 +30,7 @@ Offset Proto Name Meaning
|
|||
1E9/001 ALL eddbuf_entries Number of entries in eddbuf (below)
|
||||
1EA/001 ALL edd_mbr_sig_buf_entries Number of entries in edd_mbr_sig_buffer
|
||||
(below)
|
||||
1EF/001 ALL sentinel Used to detect broken bootloaders
|
||||
290/040 ALL edd_mbr_sig_buffer EDD MBR signatures
|
||||
2D0/A00 ALL e820_map E820 memory map table
|
||||
(array of struct e820entry)
|
||||
|
|
10
MAINTAINERS
10
MAINTAINERS
|
@ -2966,7 +2966,7 @@ S: Maintained
|
|||
F: drivers/net/ethernet/i825xx/eexpress.*
|
||||
|
||||
ETHERNET BRIDGE
|
||||
M: Stephen Hemminger <shemminger@vyatta.com>
|
||||
M: Stephen Hemminger <stephen@networkplumber.org>
|
||||
L: bridge@lists.linux-foundation.org
|
||||
L: netdev@vger.kernel.org
|
||||
W: http://www.linuxfoundation.org/en/Net:Bridge
|
||||
|
@ -4914,7 +4914,7 @@ S: Maintained
|
|||
|
||||
MARVELL GIGABIT ETHERNET DRIVERS (skge/sky2)
|
||||
M: Mirko Lindner <mlindner@marvell.com>
|
||||
M: Stephen Hemminger <shemminger@vyatta.com>
|
||||
M: Stephen Hemminger <stephen@networkplumber.org>
|
||||
L: netdev@vger.kernel.org
|
||||
S: Maintained
|
||||
F: drivers/net/ethernet/marvell/sk*
|
||||
|
@ -5189,7 +5189,7 @@ S: Supported
|
|||
F: drivers/infiniband/hw/nes/
|
||||
|
||||
NETEM NETWORK EMULATOR
|
||||
M: Stephen Hemminger <shemminger@vyatta.com>
|
||||
M: Stephen Hemminger <stephen@networkplumber.org>
|
||||
L: netem@lists.linux-foundation.org
|
||||
S: Maintained
|
||||
F: net/sched/sch_netem.c
|
||||
|
@ -6594,7 +6594,7 @@ F: drivers/media/platform/s3c-camif/
|
|||
F: include/media/s3c_camif.h
|
||||
|
||||
SERIAL DRIVERS
|
||||
M: Alan Cox <alan@linux.intel.com>
|
||||
M: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||||
L: linux-serial@vger.kernel.org
|
||||
S: Maintained
|
||||
F: drivers/tty/serial
|
||||
|
@ -7097,7 +7097,7 @@ F: include/uapi/sound/
|
|||
F: sound/
|
||||
|
||||
SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT (ASoC)
|
||||
M: Liam Girdwood <lrg@ti.com>
|
||||
M: Liam Girdwood <lgirdwood@gmail.com>
|
||||
M: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
||||
T: git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
|
||||
L: alsa-devel@alsa-project.org (moderated for non-subscribers)
|
||||
|
|
4
Makefile
4
Makefile
|
@ -1,7 +1,7 @@
|
|||
VERSION = 3
|
||||
PATCHLEVEL = 8
|
||||
SUBLEVEL = 0
|
||||
EXTRAVERSION = -rc4
|
||||
EXTRAVERSION = -rc5
|
||||
NAME = Terrified Chipmunk
|
||||
|
||||
# *DOCUMENTATION*
|
||||
|
@ -169,7 +169,7 @@ SUBARCH := $(shell uname -m | sed -e s/i.86/i386/ -e s/sun4u/sparc64/ \
|
|||
-e s/arm.*/arm/ -e s/sa110/arm/ \
|
||||
-e s/s390x/s390/ -e s/parisc64/parisc/ \
|
||||
-e s/ppc.*/powerpc/ -e s/mips.*/mips/ \
|
||||
-e s/sh[234].*/sh/ )
|
||||
-e s/sh[234].*/sh/ -e s/aarch64.*/arm64/ )
|
||||
|
||||
# Cross compiling and selecting different set of gcc/bin-utils
|
||||
# ---------------------------------------------------------------------------
|
||||
|
|
|
@ -4,6 +4,7 @@ config ARM
|
|||
select ARCH_BINFMT_ELF_RANDOMIZE_PIE
|
||||
select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
|
||||
select ARCH_HAVE_CUSTOM_GPIO_H
|
||||
select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
|
||||
select ARCH_WANT_IPC_PARSE_VERSION
|
||||
select BUILDTIME_EXTABLE_SORT if MMU
|
||||
select CPU_PM if (SUSPEND || CPU_IDLE)
|
||||
|
|
|
@ -26,7 +26,7 @@ chosen {
|
|||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x00000000 0x20000000>; /* 512 MB */
|
||||
reg = <0x00000000 0x40000000>; /* 1 GB */
|
||||
};
|
||||
|
||||
soc {
|
||||
|
|
|
@ -50,27 +50,25 @@ pinctrl {
|
|||
};
|
||||
|
||||
gpio0: gpio@d0018100 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018100 0x40>,
|
||||
<0xd0018800 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018100 0x40>;
|
||||
ngpios = <32>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <16>, <17>, <18>, <19>;
|
||||
interrupts = <82>, <83>, <84>, <85>;
|
||||
};
|
||||
|
||||
gpio1: gpio@d0018140 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018140 0x40>,
|
||||
<0xd0018840 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018140 0x40>;
|
||||
ngpios = <17>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <20>, <21>, <22>;
|
||||
interrupts = <87>, <88>, <89>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
|
@ -51,39 +51,36 @@ pinctrl {
|
|||
};
|
||||
|
||||
gpio0: gpio@d0018100 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018100 0x40>,
|
||||
<0xd0018800 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018100 0x40>;
|
||||
ngpios = <32>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <16>, <17>, <18>, <19>;
|
||||
interrupts = <82>, <83>, <84>, <85>;
|
||||
};
|
||||
|
||||
gpio1: gpio@d0018140 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018140 0x40>,
|
||||
<0xd0018840 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018140 0x40>;
|
||||
ngpios = <32>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <20>, <21>, <22>, <23>;
|
||||
interrupts = <87>, <88>, <89>, <90>;
|
||||
};
|
||||
|
||||
gpio2: gpio@d0018180 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018180 0x40>,
|
||||
<0xd0018870 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018180 0x40>;
|
||||
ngpios = <3>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <24>;
|
||||
interrupts = <91>;
|
||||
};
|
||||
|
||||
ethernet@d0034000 {
|
||||
|
|
|
@ -66,39 +66,36 @@ pinctrl {
|
|||
};
|
||||
|
||||
gpio0: gpio@d0018100 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018100 0x40>,
|
||||
<0xd0018800 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018100 0x40>;
|
||||
ngpios = <32>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <16>, <17>, <18>, <19>;
|
||||
interrupts = <82>, <83>, <84>, <85>;
|
||||
};
|
||||
|
||||
gpio1: gpio@d0018140 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018140 0x40>,
|
||||
<0xd0018840 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018140 0x40>;
|
||||
ngpios = <32>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <20>, <21>, <22>, <23>;
|
||||
interrupts = <87>, <88>, <89>, <90>;
|
||||
};
|
||||
|
||||
gpio2: gpio@d0018180 {
|
||||
compatible = "marvell,armadaxp-gpio";
|
||||
reg = <0xd0018180 0x40>,
|
||||
<0xd0018870 0x30>;
|
||||
compatible = "marvell,orion-gpio";
|
||||
reg = <0xd0018180 0x40>;
|
||||
ngpios = <3>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupts-cells = <2>;
|
||||
interrupts = <24>;
|
||||
interrupts = <91>;
|
||||
};
|
||||
|
||||
ethernet@d0034000 {
|
||||
|
|
|
@ -336,8 +336,8 @@ usb0: ohci@00300000 {
|
|||
|
||||
i2c@0 {
|
||||
compatible = "i2c-gpio";
|
||||
gpios = <&pioA 23 0 /* sda */
|
||||
&pioA 24 0 /* scl */
|
||||
gpios = <&pioA 25 0 /* sda */
|
||||
&pioA 26 0 /* scl */
|
||||
>;
|
||||
i2c-gpio,sda-open-drain;
|
||||
i2c-gpio,scl-open-drain;
|
||||
|
|
|
@ -143,6 +143,11 @@ pinctrl_usart0_cts: usart0_cts-0 {
|
|||
atmel,pins =
|
||||
<0 3 0x1 0x0>; /* PA3 periph A */
|
||||
};
|
||||
|
||||
pinctrl_usart0_sck: usart0_sck-0 {
|
||||
atmel,pins =
|
||||
<0 4 0x1 0x0>; /* PA4 periph A */
|
||||
};
|
||||
};
|
||||
|
||||
usart1 {
|
||||
|
@ -154,12 +159,17 @@ pinctrl_usart1: usart1-0 {
|
|||
|
||||
pinctrl_usart1_rts: usart1_rts-0 {
|
||||
atmel,pins =
|
||||
<3 27 0x3 0x0>; /* PC27 periph C */
|
||||
<2 27 0x3 0x0>; /* PC27 periph C */
|
||||
};
|
||||
|
||||
pinctrl_usart1_cts: usart1_cts-0 {
|
||||
atmel,pins =
|
||||
<3 28 0x3 0x0>; /* PC28 periph C */
|
||||
<2 28 0x3 0x0>; /* PC28 periph C */
|
||||
};
|
||||
|
||||
pinctrl_usart1_sck: usart1_sck-0 {
|
||||
atmel,pins =
|
||||
<2 28 0x3 0x0>; /* PC29 periph C */
|
||||
};
|
||||
};
|
||||
|
||||
|
@ -172,46 +182,56 @@ pinctrl_usart2: usart2-0 {
|
|||
|
||||
pinctrl_uart2_rts: uart2_rts-0 {
|
||||
atmel,pins =
|
||||
<0 0 0x2 0x0>; /* PB0 periph B */
|
||||
<1 0 0x2 0x0>; /* PB0 periph B */
|
||||
};
|
||||
|
||||
pinctrl_uart2_cts: uart2_cts-0 {
|
||||
atmel,pins =
|
||||
<0 1 0x2 0x0>; /* PB1 periph B */
|
||||
<1 1 0x2 0x0>; /* PB1 periph B */
|
||||
};
|
||||
|
||||
pinctrl_usart2_sck: usart2_sck-0 {
|
||||
atmel,pins =
|
||||
<1 2 0x2 0x0>; /* PB2 periph B */
|
||||
};
|
||||
};
|
||||
|
||||
usart3 {
|
||||
pinctrl_uart3: usart3-0 {
|
||||
atmel,pins =
|
||||
<3 23 0x2 0x1 /* PC22 periph B with pullup */
|
||||
3 23 0x2 0x0>; /* PC23 periph B */
|
||||
<2 23 0x2 0x1 /* PC22 periph B with pullup */
|
||||
2 23 0x2 0x0>; /* PC23 periph B */
|
||||
};
|
||||
|
||||
pinctrl_usart3_rts: usart3_rts-0 {
|
||||
atmel,pins =
|
||||
<3 24 0x2 0x0>; /* PC24 periph B */
|
||||
<2 24 0x2 0x0>; /* PC24 periph B */
|
||||
};
|
||||
|
||||
pinctrl_usart3_cts: usart3_cts-0 {
|
||||
atmel,pins =
|
||||
<3 25 0x2 0x0>; /* PC25 periph B */
|
||||
<2 25 0x2 0x0>; /* PC25 periph B */
|
||||
};
|
||||
|
||||
pinctrl_usart3_sck: usart3_sck-0 {
|
||||
atmel,pins =
|
||||
<2 26 0x2 0x0>; /* PC26 periph B */
|
||||
};
|
||||
};
|
||||
|
||||
uart0 {
|
||||
pinctrl_uart0: uart0-0 {
|
||||
atmel,pins =
|
||||
<3 8 0x3 0x0 /* PC8 periph C */
|
||||
3 9 0x3 0x1>; /* PC9 periph C with pullup */
|
||||
<2 8 0x3 0x0 /* PC8 periph C */
|
||||
2 9 0x3 0x1>; /* PC9 periph C with pullup */
|
||||
};
|
||||
};
|
||||
|
||||
uart1 {
|
||||
pinctrl_uart1: uart1-0 {
|
||||
atmel,pins =
|
||||
<3 16 0x3 0x0 /* PC16 periph C */
|
||||
3 17 0x3 0x1>; /* PC17 periph C with pullup */
|
||||
<2 16 0x3 0x0 /* PC16 periph C */
|
||||
2 17 0x3 0x1>; /* PC17 periph C with pullup */
|
||||
};
|
||||
};
|
||||
|
||||
|
@ -240,14 +260,14 @@ pinctrl_macb0_rmii: macb0_rmii-0 {
|
|||
|
||||
pinctrl_macb0_rmii_mii: macb0_rmii_mii-0 {
|
||||
atmel,pins =
|
||||
<1 8 0x1 0x0 /* PA8 periph A */
|
||||
1 11 0x1 0x0 /* PA11 periph A */
|
||||
1 12 0x1 0x0 /* PA12 periph A */
|
||||
1 13 0x1 0x0 /* PA13 periph A */
|
||||
1 14 0x1 0x0 /* PA14 periph A */
|
||||
1 15 0x1 0x0 /* PA15 periph A */
|
||||
1 16 0x1 0x0 /* PA16 periph A */
|
||||
1 17 0x1 0x0>; /* PA17 periph A */
|
||||
<1 8 0x1 0x0 /* PB8 periph A */
|
||||
1 11 0x1 0x0 /* PB11 periph A */
|
||||
1 12 0x1 0x0 /* PB12 periph A */
|
||||
1 13 0x1 0x0 /* PB13 periph A */
|
||||
1 14 0x1 0x0 /* PB14 periph A */
|
||||
1 15 0x1 0x0 /* PB15 periph A */
|
||||
1 16 0x1 0x0 /* PB16 periph A */
|
||||
1 17 0x1 0x0>; /* PB17 periph A */
|
||||
};
|
||||
};
|
||||
|
||||
|
|
|
@ -96,8 +96,8 @@ dwmmc0@12200000 {
|
|||
fifo-depth = <0x80>;
|
||||
card-detect-delay = <200>;
|
||||
samsung,dw-mshc-ciu-div = <3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2 3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2>;
|
||||
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
|
@ -120,8 +120,8 @@ dwmmc2@12220000 {
|
|||
fifo-depth = <0x80>;
|
||||
card-detect-delay = <200>;
|
||||
samsung,dw-mshc-ciu-div = <3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2 3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2>;
|
||||
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
|
@ -141,8 +141,8 @@ dwmmc3@12230000 {
|
|||
fifo-depth = <0x80>;
|
||||
card-detect-delay = <200>;
|
||||
samsung,dw-mshc-ciu-div = <3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2 3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2>;
|
||||
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
|
|
|
@ -26,10 +26,15 @@ power {
|
|||
};
|
||||
|
||||
&uart0 { status = "okay"; };
|
||||
&sdio0 { status = "okay"; };
|
||||
&sata0 { status = "okay"; };
|
||||
&i2c0 { status = "okay"; };
|
||||
|
||||
&sdio0 {
|
||||
status = "okay";
|
||||
/* sdio0 card detect is connected to wrong pin on CuBox */
|
||||
cd-gpios = <&gpio0 12 1>;
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
|
@ -42,9 +47,14 @@ spi-flash@0 {
|
|||
};
|
||||
|
||||
&pinctrl {
|
||||
pinctrl-0 = <&pmx_gpio_18>;
|
||||
pinctrl-0 = <&pmx_gpio_12 &pmx_gpio_18>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
pmx_gpio_12: pmx-gpio-12 {
|
||||
marvell,pins = "mpp12";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_gpio_18: pmx-gpio-18 {
|
||||
marvell,pins = "mpp18";
|
||||
marvell,function = "gpio";
|
||||
|
|
|
@ -115,8 +115,8 @@ dwmmc0@12200000 {
|
|||
fifo-depth = <0x80>;
|
||||
card-detect-delay = <200>;
|
||||
samsung,dw-mshc-ciu-div = <3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2 3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2>;
|
||||
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
|
@ -139,8 +139,8 @@ dwmmc2@12220000 {
|
|||
fifo-depth = <0x80>;
|
||||
card-detect-delay = <200>;
|
||||
samsung,dw-mshc-ciu-div = <3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2 3>;
|
||||
samsung,dw-mshc-sdr-timing = <2 3>;
|
||||
samsung,dw-mshc-ddr-timing = <1 2>;
|
||||
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
|
|
|
@ -1,4 +1,5 @@
|
|||
/include/ "kirkwood.dtsi"
|
||||
/include/ "kirkwood-6281.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
|
@ -6,6 +7,21 @@ chosen {
|
|||
};
|
||||
|
||||
ocp@f1000000 {
|
||||
pinctrl: pinctrl@10000 {
|
||||
pinctrl-0 = < &pmx_spi &pmx_twsi0 &pmx_uart0
|
||||
&pmx_ns2_sata0 &pmx_ns2_sata1>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
pmx_ns2_sata0: pmx-ns2-sata0 {
|
||||
marvell,pins = "mpp21";
|
||||
marvell,function = "sata0";
|
||||
};
|
||||
pmx_ns2_sata1: pmx-ns2-sata1 {
|
||||
marvell,pins = "mpp20";
|
||||
marvell,function = "sata1";
|
||||
};
|
||||
};
|
||||
|
||||
serial@12000 {
|
||||
clock-frequency = <166666667>;
|
||||
status = "okay";
|
||||
|
|
|
@ -36,6 +36,7 @@ gpio0: gpio@10100 {
|
|||
reg = <0x10100 0x40>;
|
||||
ngpios = <32>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
interrupts = <35>, <36>, <37>, <38>;
|
||||
};
|
||||
|
||||
|
@ -46,6 +47,7 @@ gpio1: gpio@10140 {
|
|||
reg = <0x10140 0x40>;
|
||||
ngpios = <18>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
interrupts = <39>, <40>, <41>;
|
||||
};
|
||||
|
||||
|
|
|
@ -48,6 +48,8 @@ usart1: serial@fffb4000 {
|
|||
|
||||
macb0: ethernet@fffc4000 {
|
||||
phy-mode = "mii";
|
||||
pinctrl-0 = <&pinctrl_macb_rmii
|
||||
&pinctrl_macb_rmii_mii_alt>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
|
|
|
@ -60,19 +60,21 @@ intc: interrupt-controller@01c20400 {
|
|||
};
|
||||
|
||||
uart0: uart@01c28000 {
|
||||
compatible = "ns8250";
|
||||
compatible = "snps,dw-apb-uart";
|
||||
reg = <0x01c28000 0x400>;
|
||||
interrupts = <1>;
|
||||
reg-shift = <2>;
|
||||
reg-io-width = <4>;
|
||||
clock-frequency = <24000000>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart1: uart@01c28400 {
|
||||
compatible = "ns8250";
|
||||
compatible = "snps,dw-apb-uart";
|
||||
reg = <0x01c28400 0x400>;
|
||||
interrupts = <2>;
|
||||
reg-shift = <2>;
|
||||
reg-io-width = <4>;
|
||||
clock-frequency = <24000000>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
|
|
@ -45,7 +45,6 @@ cpu1: cpu@1 {
|
|||
reg = <1>;
|
||||
};
|
||||
|
||||
/* A7s disabled till big.LITTLE patches are available...
|
||||
cpu2: cpu@2 {
|
||||
device_type = "cpu";
|
||||
compatible = "arm,cortex-a7";
|
||||
|
@ -63,7 +62,6 @@ cpu4: cpu@4 {
|
|||
compatible = "arm,cortex-a7";
|
||||
reg = <0x102>;
|
||||
};
|
||||
*/
|
||||
};
|
||||
|
||||
memory@80000000 {
|
||||
|
|
|
@ -19,6 +19,7 @@ CONFIG_SOC_AT91SAM9260=y
|
|||
CONFIG_SOC_AT91SAM9263=y
|
||||
CONFIG_SOC_AT91SAM9G45=y
|
||||
CONFIG_SOC_AT91SAM9X5=y
|
||||
CONFIG_SOC_AT91SAM9N12=y
|
||||
CONFIG_MACH_AT91SAM_DT=y
|
||||
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
|
||||
CONFIG_AT91_TIMER_HZ=128
|
||||
|
@ -31,7 +32,7 @@ CONFIG_ZBOOT_ROM_TEXT=0x0
|
|||
CONFIG_ZBOOT_ROM_BSS=0x0
|
||||
CONFIG_ARM_APPENDED_DTB=y
|
||||
CONFIG_ARM_ATAG_DTB_COMPAT=y
|
||||
CONFIG_CMDLINE="mem=128M console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
|
||||
CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
|
||||
CONFIG_KEXEC=y
|
||||
CONFIG_AUTO_ZRELADDR=y
|
||||
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
|
||||
|
|
|
@ -100,12 +100,14 @@ ENTRY(printch)
|
|||
b 1b
|
||||
ENDPROC(printch)
|
||||
|
||||
#ifdef CONFIG_MMU
|
||||
ENTRY(debug_ll_addr)
|
||||
addruart r2, r3, ip
|
||||
str r2, [r0]
|
||||
str r3, [r1]
|
||||
mov pc, lr
|
||||
ENDPROC(debug_ll_addr)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
||||
|
|
|
@ -246,6 +246,7 @@ __create_page_tables:
|
|||
|
||||
/*
|
||||
* Then map boot params address in r2 if specified.
|
||||
* We map 2 sections in case the ATAGs/DTB crosses a section boundary.
|
||||
*/
|
||||
mov r0, r2, lsr #SECTION_SHIFT
|
||||
movs r0, r0, lsl #SECTION_SHIFT
|
||||
|
@ -253,6 +254,8 @@ __create_page_tables:
|
|||
addne r3, r3, #PAGE_OFFSET
|
||||
addne r3, r4, r3, lsr #(SECTION_SHIFT - PMD_ORDER)
|
||||
orrne r6, r7, r0
|
||||
strne r6, [r3], #1 << PMD_ORDER
|
||||
addne r6, r6, #1 << SECTION_SHIFT
|
||||
strne r6, [r3]
|
||||
|
||||
#ifdef CONFIG_DEBUG_LL
|
||||
|
@ -331,7 +334,7 @@ ENTRY(secondary_startup)
|
|||
* as it has already been validated by the primary processor.
|
||||
*/
|
||||
#ifdef CONFIG_ARM_VIRT_EXT
|
||||
bl __hyp_stub_install
|
||||
bl __hyp_stub_install_secondary
|
||||
#endif
|
||||
safe_svcmode_maskall r9
|
||||
|
||||
|
|
|
@ -99,7 +99,7 @@ ENTRY(__hyp_stub_install_secondary)
|
|||
* immediately.
|
||||
*/
|
||||
compare_cpu_mode_with_primary r4, r5, r6, r7
|
||||
bxne lr
|
||||
movne pc, lr
|
||||
|
||||
/*
|
||||
* Once we have given up on one CPU, we do not try to install the
|
||||
|
@ -111,7 +111,7 @@ ENTRY(__hyp_stub_install_secondary)
|
|||
*/
|
||||
|
||||
cmp r4, #HYP_MODE
|
||||
bxne lr @ give up if the CPU is not in HYP mode
|
||||
movne pc, lr @ give up if the CPU is not in HYP mode
|
||||
|
||||
/*
|
||||
* Configure HSCTLR to set correct exception endianness/instruction set
|
||||
|
@ -120,7 +120,8 @@ ENTRY(__hyp_stub_install_secondary)
|
|||
* Eventually, CPU-specific code might be needed -- assume not for now
|
||||
*
|
||||
* This code relies on the "eret" instruction to synchronize the
|
||||
* various coprocessor accesses.
|
||||
* various coprocessor accesses. This is done when we switch to SVC
|
||||
* (see safe_svcmode_maskall).
|
||||
*/
|
||||
@ Now install the hypervisor stub:
|
||||
adr r7, __hyp_stub_vectors
|
||||
|
@ -155,14 +156,7 @@ THUMB( orr r7, #(1 << 30) ) @ HSCTLR.TE
|
|||
1:
|
||||
#endif
|
||||
|
||||
bic r7, r4, #MODE_MASK
|
||||
orr r7, r7, #SVC_MODE
|
||||
THUMB( orr r7, r7, #PSR_T_BIT )
|
||||
msr spsr_cxsf, r7 @ This is SPSR_hyp.
|
||||
|
||||
__MSR_ELR_HYP(14) @ msr elr_hyp, lr
|
||||
__ERET @ return, switching to SVC mode
|
||||
@ The boot CPU mode is left in r4.
|
||||
bx lr @ The boot CPU mode is left in r4.
|
||||
ENDPROC(__hyp_stub_install_secondary)
|
||||
|
||||
__hyp_stub_do_trap:
|
||||
|
@ -200,7 +194,7 @@ ENDPROC(__hyp_get_vectors)
|
|||
@ fall through
|
||||
ENTRY(__hyp_set_vectors)
|
||||
__HVC(0)
|
||||
bx lr
|
||||
mov pc, lr
|
||||
ENDPROC(__hyp_set_vectors)
|
||||
|
||||
#ifndef ZIMAGE
|
||||
|
|
|
@ -475,14 +475,8 @@ u64 smp_irq_stat_cpu(unsigned int cpu)
|
|||
*/
|
||||
static DEFINE_PER_CPU(struct clock_event_device, percpu_clockevent);
|
||||
|
||||
static void ipi_timer(void)
|
||||
{
|
||||
struct clock_event_device *evt = &__get_cpu_var(percpu_clockevent);
|
||||
evt->event_handler(evt);
|
||||
}
|
||||
|
||||
#ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
|
||||
static void smp_timer_broadcast(const struct cpumask *mask)
|
||||
void tick_broadcast(const struct cpumask *mask)
|
||||
{
|
||||
smp_cross_call(mask, IPI_TIMER);
|
||||
}
|
||||
|
@ -530,7 +524,6 @@ static void __cpuinit percpu_timer_setup(void)
|
|||
struct clock_event_device *evt = &per_cpu(percpu_clockevent, cpu);
|
||||
|
||||
evt->cpumask = cpumask_of(cpu);
|
||||
evt->broadcast = smp_timer_broadcast;
|
||||
|
||||
if (!lt_ops || lt_ops->setup(evt))
|
||||
broadcast_timer_setup(evt);
|
||||
|
@ -596,11 +589,13 @@ void handle_IPI(int ipinr, struct pt_regs *regs)
|
|||
case IPI_WAKEUP:
|
||||
break;
|
||||
|
||||
#ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
|
||||
case IPI_TIMER:
|
||||
irq_enter();
|
||||
ipi_timer();
|
||||
tick_receive_broadcast();
|
||||
irq_exit();
|
||||
break;
|
||||
#endif
|
||||
|
||||
case IPI_RESCHEDULE:
|
||||
scheduler_ipi();
|
||||
|
|
|
@ -105,6 +105,8 @@ static void __init soc_detect(u32 dbgu_base)
|
|||
switch (socid) {
|
||||
case ARCH_ID_AT91RM9200:
|
||||
at91_soc_initdata.type = AT91_SOC_RM9200;
|
||||
if (at91_soc_initdata.subtype == AT91_SOC_SUBTYPE_NONE)
|
||||
at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA;
|
||||
at91_boot_soc = at91rm9200_soc;
|
||||
break;
|
||||
|
||||
|
|
|
@ -851,6 +851,7 @@ config SOC_IMX6Q
|
|||
select HAVE_CAN_FLEXCAN if CAN
|
||||
select HAVE_IMX_GPC
|
||||
select HAVE_IMX_MMDC
|
||||
select HAVE_IMX_SRC
|
||||
select HAVE_SMP
|
||||
select MFD_SYSCON
|
||||
select PINCTRL
|
||||
|
|
|
@ -254,9 +254,9 @@ int __init mx25_clocks_init(void)
|
|||
clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usbotg_ahb], "ahb", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[usbotg_ahb], "ahb", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[nfc_ipg_per], NULL, "imx25-nand.0");
|
||||
/* i.mx25 has the i.mx35 type cspi */
|
||||
clk_register_clkdev(clk[cspi1_ipg], NULL, "imx35-cspi.0");
|
||||
|
|
|
@ -236,9 +236,9 @@ int __init mx27_clocks_init(unsigned long fref)
|
|||
clk_register_clkdev(clk[lcdc_ahb_gate], "ahb", "imx21-fb.0");
|
||||
clk_register_clkdev(clk[csi_ahb_gate], "ahb", "imx27-camera.0");
|
||||
clk_register_clkdev(clk[per4_gate], "per", "imx27-camera.0");
|
||||
clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usb_ipg_gate], "ipg", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usb_ahb_gate], "ahb", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[usb_ipg_gate], "ipg", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[usb_ahb_gate], "ahb", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.0");
|
||||
clk_register_clkdev(clk[usb_ipg_gate], "ipg", "mxc-ehci.0");
|
||||
clk_register_clkdev(clk[usb_ahb_gate], "ahb", "mxc-ehci.0");
|
||||
|
|
|
@ -139,9 +139,9 @@ int __init mx31_clocks_init(unsigned long fref)
|
|||
clk_register_clkdev(clk[usb_div_post], "per", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usb_gate], "ahb", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usb_div_post], "per", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usb_gate], "ahb", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usb_div_post], "per", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[usb_gate], "ahb", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0");
|
||||
/* i.mx31 has the i.mx21 type uart */
|
||||
clk_register_clkdev(clk[uart1_gate], "per", "imx21-uart.0");
|
||||
|
|
|
@ -251,9 +251,9 @@ int __init mx35_clocks_init()
|
|||
clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usbotg_gate], "ahb", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usbotg_gate], "ahb", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[usbotg_gate], "ahb", "imx-udc-mx27");
|
||||
clk_register_clkdev(clk[wdog_gate], NULL, "imx2-wdt.0");
|
||||
clk_register_clkdev(clk[nfc_div], NULL, "imx25-nand.0");
|
||||
clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0");
|
||||
|
|
|
@ -269,9 +269,9 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
|
|||
clk_register_clkdev(clk[usboh3_per_gate], "per", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usboh3_gate], "ipg", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usboh3_gate], "ahb", "mxc-ehci.2");
|
||||
clk_register_clkdev(clk[usboh3_per_gate], "per", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usboh3_gate], "ipg", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usboh3_gate], "ahb", "fsl-usb2-udc");
|
||||
clk_register_clkdev(clk[usboh3_per_gate], "per", "imx-udc-mx51");
|
||||
clk_register_clkdev(clk[usboh3_gate], "ipg", "imx-udc-mx51");
|
||||
clk_register_clkdev(clk[usboh3_gate], "ahb", "imx-udc-mx51");
|
||||
clk_register_clkdev(clk[nfc_gate], NULL, "imx51-nand");
|
||||
clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "imx-ssi.0");
|
||||
clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "imx-ssi.1");
|
||||
|
|
|
@ -436,6 +436,9 @@ int __init mx6q_clocks_init(void)
|
|||
for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
|
||||
clk_prepare_enable(clk[clks_init_on[i]]);
|
||||
|
||||
/* Set initial power mode */
|
||||
imx6q_set_lpm(WAIT_CLOCKED);
|
||||
|
||||
np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
|
||||
base = of_iomap(np, 0);
|
||||
WARN_ON(!base);
|
||||
|
|
|
@ -142,6 +142,7 @@ extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
|
|||
extern void imx6q_clock_map_io(void);
|
||||
|
||||
extern void imx_cpu_die(unsigned int cpu);
|
||||
extern int imx_cpu_kill(unsigned int cpu);
|
||||
|
||||
#ifdef CONFIG_PM
|
||||
extern void imx6q_pm_init(void);
|
||||
|
|
|
@ -63,6 +63,7 @@ struct platform_device *__init imx_add_flexcan(
|
|||
|
||||
#include <linux/fsl_devices.h>
|
||||
struct imx_fsl_usb2_udc_data {
|
||||
const char *devid;
|
||||
resource_size_t iobase;
|
||||
resource_size_t irq;
|
||||
};
|
||||
|
|
|
@ -11,35 +11,36 @@
|
|||
#include "../hardware.h"
|
||||
#include "devices-common.h"
|
||||
|
||||
#define imx_fsl_usb2_udc_data_entry_single(soc) \
|
||||
#define imx_fsl_usb2_udc_data_entry_single(soc, _devid) \
|
||||
{ \
|
||||
.devid = _devid, \
|
||||
.iobase = soc ## _USB_OTG_BASE_ADDR, \
|
||||
.irq = soc ## _INT_USB_OTG, \
|
||||
}
|
||||
|
||||
#ifdef CONFIG_SOC_IMX25
|
||||
const struct imx_fsl_usb2_udc_data imx25_fsl_usb2_udc_data __initconst =
|
||||
imx_fsl_usb2_udc_data_entry_single(MX25);
|
||||
imx_fsl_usb2_udc_data_entry_single(MX25, "imx-udc-mx27");
|
||||
#endif /* ifdef CONFIG_SOC_IMX25 */
|
||||
|
||||
#ifdef CONFIG_SOC_IMX27
|
||||
const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data __initconst =
|
||||
imx_fsl_usb2_udc_data_entry_single(MX27);
|
||||
imx_fsl_usb2_udc_data_entry_single(MX27, "imx-udc-mx27");
|
||||
#endif /* ifdef CONFIG_SOC_IMX27 */
|
||||
|
||||
#ifdef CONFIG_SOC_IMX31
|
||||
const struct imx_fsl_usb2_udc_data imx31_fsl_usb2_udc_data __initconst =
|
||||
imx_fsl_usb2_udc_data_entry_single(MX31);
|
||||
imx_fsl_usb2_udc_data_entry_single(MX31, "imx-udc-mx27");
|
||||
#endif /* ifdef CONFIG_SOC_IMX31 */
|
||||
|
||||
#ifdef CONFIG_SOC_IMX35
|
||||
const struct imx_fsl_usb2_udc_data imx35_fsl_usb2_udc_data __initconst =
|
||||
imx_fsl_usb2_udc_data_entry_single(MX35);
|
||||
imx_fsl_usb2_udc_data_entry_single(MX35, "imx-udc-mx27");
|
||||
#endif /* ifdef CONFIG_SOC_IMX35 */
|
||||
|
||||
#ifdef CONFIG_SOC_IMX51
|
||||
const struct imx_fsl_usb2_udc_data imx51_fsl_usb2_udc_data __initconst =
|
||||
imx_fsl_usb2_udc_data_entry_single(MX51);
|
||||
imx_fsl_usb2_udc_data_entry_single(MX51, "imx-udc-mx51");
|
||||
#endif
|
||||
|
||||
struct platform_device *__init imx_add_fsl_usb2_udc(
|
||||
|
@ -57,7 +58,7 @@ struct platform_device *__init imx_add_fsl_usb2_udc(
|
|||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
};
|
||||
return imx_add_platform_device_dmamask("fsl-usb2-udc", -1,
|
||||
return imx_add_platform_device_dmamask(data->devid, -1,
|
||||
res, ARRAY_SIZE(res),
|
||||
pdata, sizeof(*pdata), DMA_BIT_MASK(32));
|
||||
}
|
||||
|
|
|
@ -54,7 +54,7 @@ struct platform_device *__init imx_add_imx_fb(
|
|||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
};
|
||||
return imx_add_platform_device_dmamask("imx-fb", 0,
|
||||
return imx_add_platform_device_dmamask(data->devid, 0,
|
||||
res, ARRAY_SIZE(res),
|
||||
pdata, sizeof(*pdata), DMA_BIT_MASK(32));
|
||||
}
|
||||
|
|
|
@ -46,9 +46,11 @@ static inline void cpu_enter_lowpower(void)
|
|||
void imx_cpu_die(unsigned int cpu)
|
||||
{
|
||||
cpu_enter_lowpower();
|
||||
imx_enable_cpu(cpu, false);
|
||||
|
||||
/* spin here until hardware takes it down */
|
||||
while (1)
|
||||
;
|
||||
cpu_do_idle();
|
||||
}
|
||||
|
||||
int imx_cpu_kill(unsigned int cpu)
|
||||
{
|
||||
imx_enable_cpu(cpu, false);
|
||||
return 1;
|
||||
}
|
||||
|
|
|
@ -22,8 +22,7 @@
|
|||
#include <linux/module.h>
|
||||
#include <linux/spinlock.h>
|
||||
#include <linux/genalloc.h>
|
||||
|
||||
#include "iram.h"
|
||||
#include "linux/platform_data/imx-iram.h"
|
||||
|
||||
static unsigned long iram_phys_base;
|
||||
static void __iomem *iram_virt_base;
|
||||
|
|
|
@ -92,5 +92,6 @@ struct smp_operations imx_smp_ops __initdata = {
|
|||
.smp_boot_secondary = imx_boot_secondary,
|
||||
#ifdef CONFIG_HOTPLUG_CPU
|
||||
.cpu_die = imx_cpu_die,
|
||||
.cpu_kill = imx_cpu_kill,
|
||||
#endif
|
||||
};
|
||||
|
|
|
@ -41,6 +41,7 @@ static int imx6q_pm_enter(suspend_state_t state)
|
|||
cpu_suspend(0, imx6q_suspend_finish);
|
||||
imx_smp_prepare();
|
||||
imx_gpc_post_resume();
|
||||
imx6q_set_lpm(WAIT_CLOCKED);
|
||||
break;
|
||||
default:
|
||||
return -EINVAL;
|
||||
|
|
|
@ -475,13 +475,12 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys)
|
|||
{
|
||||
int ret = 0;
|
||||
|
||||
if (!ap_syscon_base)
|
||||
return -EINVAL;
|
||||
|
||||
if (nr == 0) {
|
||||
sys->mem_offset = PHYS_PCI_MEM_BASE;
|
||||
ret = pci_v3_setup_resources(sys);
|
||||
/* Remap the Integrator system controller */
|
||||
ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100);
|
||||
if (!ap_syscon_base)
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
return ret;
|
||||
|
@ -497,6 +496,13 @@ void __init pci_v3_preinit(void)
|
|||
unsigned int temp;
|
||||
int ret;
|
||||
|
||||
/* Remap the Integrator system controller */
|
||||
ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100);
|
||||
if (!ap_syscon_base) {
|
||||
pr_err("unable to remap the AP syscon for PCIv3\n");
|
||||
return;
|
||||
}
|
||||
|
||||
pcibios_min_mem = 0x00100000;
|
||||
|
||||
/*
|
||||
|
|
|
@ -18,47 +18,11 @@
|
|||
#include <linux/gpio.h>
|
||||
#include <linux/of.h>
|
||||
#include "common.h"
|
||||
#include "mpp.h"
|
||||
|
||||
static struct mv643xx_eth_platform_data ns2_ge00_data = {
|
||||
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
|
||||
};
|
||||
|
||||
static unsigned int ns2_mpp_config[] __initdata = {
|
||||
MPP0_SPI_SCn,
|
||||
MPP1_SPI_MOSI,
|
||||
MPP2_SPI_SCK,
|
||||
MPP3_SPI_MISO,
|
||||
MPP4_NF_IO6,
|
||||
MPP5_NF_IO7,
|
||||
MPP6_SYSRST_OUTn,
|
||||
MPP7_GPO, /* Fan speed (bit 1) */
|
||||
MPP8_TW0_SDA,
|
||||
MPP9_TW0_SCK,
|
||||
MPP10_UART0_TXD,
|
||||
MPP11_UART0_RXD,
|
||||
MPP12_GPO, /* Red led */
|
||||
MPP14_GPIO, /* USB fuse */
|
||||
MPP16_GPIO, /* SATA 0 power */
|
||||
MPP17_GPIO, /* SATA 1 power */
|
||||
MPP18_NF_IO0,
|
||||
MPP19_NF_IO1,
|
||||
MPP20_SATA1_ACTn,
|
||||
MPP21_SATA0_ACTn,
|
||||
MPP22_GPIO, /* Fan speed (bit 0) */
|
||||
MPP23_GPIO, /* Fan power */
|
||||
MPP24_GPIO, /* USB mode select */
|
||||
MPP25_GPIO, /* Fan rotation fail */
|
||||
MPP26_GPIO, /* USB device vbus */
|
||||
MPP28_GPIO, /* USB enable host vbus */
|
||||
MPP29_GPIO, /* Blue led (slow register) */
|
||||
MPP30_GPIO, /* Blue led (command register) */
|
||||
MPP31_GPIO, /* Board power off */
|
||||
MPP32_GPIO, /* Power button (0 = Released, 1 = Pushed) */
|
||||
MPP33_GPO, /* Fan speed (bit 2) */
|
||||
0
|
||||
};
|
||||
|
||||
#define NS2_GPIO_POWER_OFF 31
|
||||
|
||||
static void ns2_power_off(void)
|
||||
|
@ -71,8 +35,6 @@ void __init ns2_init(void)
|
|||
/*
|
||||
* Basic setup. Needs to be called early.
|
||||
*/
|
||||
kirkwood_mpp_conf(ns2_mpp_config);
|
||||
|
||||
if (of_machine_is_compatible("lacie,netspace_lite_v2") ||
|
||||
of_machine_is_compatible("lacie,netspace_mini_v2"))
|
||||
ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
|
||||
|
|
|
@ -1,6 +1,8 @@
|
|||
ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \
|
||||
-I$(srctree)/arch/arm/plat-orion/include
|
||||
|
||||
AFLAGS_coherency_ll.o := -Wa,-march=armv7-a
|
||||
|
||||
obj-y += system-controller.o
|
||||
obj-$(CONFIG_MACH_ARMADA_370_XP) += armada-370-xp.o irq-armada-370-xp.o addr-map.o coherency.o coherency_ll.o pmsu.o
|
||||
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
|
||||
|
|
|
@ -397,6 +397,12 @@ static struct omap_board_mux board_mux[] __initdata = {
|
|||
OMAP_PULL_ENA),
|
||||
OMAP4_MUX(ABE_MCBSP1_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
|
||||
|
||||
/* UART2 - BT/FM/GPS shared transport */
|
||||
OMAP4_MUX(UART2_CTS, OMAP_PIN_INPUT | OMAP_MUX_MODE0),
|
||||
OMAP4_MUX(UART2_RTS, OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
|
||||
OMAP4_MUX(UART2_RX, OMAP_PIN_INPUT | OMAP_MUX_MODE0),
|
||||
OMAP4_MUX(UART2_TX, OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
|
||||
|
||||
{ .reg_offset = OMAP_MUX_TERMINATOR },
|
||||
};
|
||||
|
||||
|
|
|
@ -1935,6 +1935,8 @@ int __init omap2420_clk_init(void)
|
|||
omap2_init_clk_hw_omap_clocks(c->lk.clk);
|
||||
}
|
||||
|
||||
omap2xxx_clkt_vps_late_init();
|
||||
|
||||
omap2_clk_disable_autoidle_all();
|
||||
|
||||
omap2_clk_enable_init_clocks(enable_init_clks,
|
||||
|
|
|
@ -2050,6 +2050,8 @@ int __init omap2430_clk_init(void)
|
|||
omap2_init_clk_hw_omap_clocks(c->lk.clk);
|
||||
}
|
||||
|
||||
omap2xxx_clkt_vps_late_init();
|
||||
|
||||
omap2_clk_disable_autoidle_all();
|
||||
|
||||
omap2_clk_enable_init_clocks(enable_init_clks,
|
||||
|
|
|
@ -2026,14 +2026,13 @@ int __init omap4xxx_clk_init(void)
|
|||
* On OMAP4460 the ABE DPLL fails to turn on if in idle low-power
|
||||
* state when turning the ABE clock domain. Workaround this by
|
||||
* locking the ABE DPLL on boot.
|
||||
* Lock the ABE DPLL in any case to avoid issues with audio.
|
||||
*/
|
||||
if (cpu_is_omap446x()) {
|
||||
rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck);
|
||||
if (!rc)
|
||||
rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ);
|
||||
if (rc)
|
||||
pr_err("%s: failed to configure ABE DPLL!\n", __func__);
|
||||
}
|
||||
rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck);
|
||||
if (!rc)
|
||||
rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ);
|
||||
if (rc)
|
||||
pr_err("%s: failed to configure ABE DPLL!\n", __func__);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
|
|
@ -639,7 +639,7 @@ static int count_ocp2scp_devices(struct omap_ocp2scp_dev *ocp2scp_dev)
|
|||
return cnt;
|
||||
}
|
||||
|
||||
static void omap_init_ocp2scp(void)
|
||||
static void __init omap_init_ocp2scp(void)
|
||||
{
|
||||
struct omap_hwmod *oh;
|
||||
struct platform_device *pdev;
|
||||
|
|
|
@ -25,6 +25,7 @@
|
|||
#include <linux/dma-mapping.h>
|
||||
#include <linux/platform_data/omap_drm.h>
|
||||
|
||||
#include "soc.h"
|
||||
#include "omap_device.h"
|
||||
#include "omap_hwmod.h"
|
||||
|
||||
|
@ -56,7 +57,7 @@ static int __init omap_init_drm(void)
|
|||
oh->name);
|
||||
}
|
||||
|
||||
platform_data.omaprev = GET_OMAP_REVISION();
|
||||
platform_data.omaprev = GET_OMAP_TYPE;
|
||||
|
||||
return platform_device_register(&omap_drm_device);
|
||||
|
||||
|
|
|
@ -2132,8 +2132,12 @@ static struct omap_hwmod omap44xx_mcpdm_hwmod = {
|
|||
* currently reset very early during boot, before I2C is
|
||||
* available, so it doesn't seem that we have any choice in
|
||||
* the kernel other than to avoid resetting it.
|
||||
*
|
||||
* Also, McPDM needs to be configured to NO_IDLE mode when it
|
||||
* is in used otherwise vital clocks will be gated which
|
||||
* results 'slow motion' audio playback.
|
||||
*/
|
||||
.flags = HWMOD_EXT_OPT_MAIN_CLK,
|
||||
.flags = HWMOD_EXT_OPT_MAIN_CLK | HWMOD_SWSUP_SIDLE,
|
||||
.mpu_irqs = omap44xx_mcpdm_irqs,
|
||||
.sdma_reqs = omap44xx_mcpdm_sdma_reqs,
|
||||
.main_clk = "mcpdm_fck",
|
||||
|
|
|
@ -165,15 +165,11 @@ static struct device_node * __init omap_get_timer_dt(struct of_device_id *match,
|
|||
struct device_node *np;
|
||||
|
||||
for_each_matching_node(np, match) {
|
||||
if (!of_device_is_available(np)) {
|
||||
of_node_put(np);
|
||||
if (!of_device_is_available(np))
|
||||
continue;
|
||||
}
|
||||
|
||||
if (property && !of_get_property(np, property, NULL)) {
|
||||
of_node_put(np);
|
||||
if (property && !of_get_property(np, property, NULL))
|
||||
continue;
|
||||
}
|
||||
|
||||
of_add_property(np, &device_disabled);
|
||||
return np;
|
||||
|
|
|
@ -47,7 +47,7 @@ static struct spi_board_info wm1253_devs[] = {
|
|||
.bus_num = 0,
|
||||
.chip_select = 0,
|
||||
.mode = SPI_MODE_0,
|
||||
.irq = S3C_EINT(5),
|
||||
.irq = S3C_EINT(4),
|
||||
.controller_data = &wm0010_spi_csinfo,
|
||||
.platform_data = &wm0010_pdata,
|
||||
},
|
||||
|
|
|
@ -338,8 +338,10 @@ int __init s3c64xx_pm_init(void)
|
|||
for (i = 0; i < ARRAY_SIZE(s3c64xx_pm_domains); i++)
|
||||
pm_genpd_init(&s3c64xx_pm_domains[i]->pd, NULL, false);
|
||||
|
||||
#ifdef CONFIG_S3C_DEV_FB
|
||||
if (dev_get_platdata(&s3c_device_fb.dev))
|
||||
pm_genpd_add_device(&s3c64xx_pm_f.pd, &s3c_device_fb.dev);
|
||||
#endif
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
|
|
@ -774,25 +774,27 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset,
|
|||
size_t size, enum dma_data_direction dir,
|
||||
void (*op)(const void *, size_t, int))
|
||||
{
|
||||
unsigned long pfn;
|
||||
size_t left = size;
|
||||
|
||||
pfn = page_to_pfn(page) + offset / PAGE_SIZE;
|
||||
offset %= PAGE_SIZE;
|
||||
|
||||
/*
|
||||
* A single sg entry may refer to multiple physically contiguous
|
||||
* pages. But we still need to process highmem pages individually.
|
||||
* If highmem is not configured then the bulk of this loop gets
|
||||
* optimized out.
|
||||
*/
|
||||
size_t left = size;
|
||||
do {
|
||||
size_t len = left;
|
||||
void *vaddr;
|
||||
|
||||
page = pfn_to_page(pfn);
|
||||
|
||||
if (PageHighMem(page)) {
|
||||
if (len + offset > PAGE_SIZE) {
|
||||
if (offset >= PAGE_SIZE) {
|
||||
page += offset / PAGE_SIZE;
|
||||
offset %= PAGE_SIZE;
|
||||
}
|
||||
if (len + offset > PAGE_SIZE)
|
||||
len = PAGE_SIZE - offset;
|
||||
}
|
||||
vaddr = kmap_high_get(page);
|
||||
if (vaddr) {
|
||||
vaddr += offset;
|
||||
|
@ -809,7 +811,7 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset,
|
|||
op(vaddr, len, dir);
|
||||
}
|
||||
offset = 0;
|
||||
page++;
|
||||
pfn++;
|
||||
left -= len;
|
||||
} while (left);
|
||||
}
|
||||
|
|
|
@ -298,7 +298,7 @@ static struct mem_type mem_types[] = {
|
|||
},
|
||||
[MT_MEMORY_SO] = {
|
||||
.prot_pte = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
|
||||
L_PTE_MT_UNCACHED,
|
||||
L_PTE_MT_UNCACHED | L_PTE_XN,
|
||||
.prot_l1 = PMD_TYPE_TABLE,
|
||||
.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_S |
|
||||
PMD_SECT_UNCACHED | PMD_SECT_XN,
|
||||
|
|
|
@ -20,7 +20,7 @@
|
|||
*/
|
||||
ENTRY(versatile_secondary_startup)
|
||||
mrc p15, 0, r0, c0, c0, 5
|
||||
and r0, r0, #15
|
||||
bic r0, #0xff000000
|
||||
adr r4, 1f
|
||||
ldmia r4, {r5, r6}
|
||||
sub r4, r4, r5
|
||||
|
|
|
@ -22,7 +22,7 @@
|
|||
@ IRQs disabled.
|
||||
@
|
||||
ENTRY(do_vfp)
|
||||
#ifdef CONFIG_PREEMPT
|
||||
#ifdef CONFIG_PREEMPT_COUNT
|
||||
ldr r4, [r10, #TI_PREEMPT] @ get preempt count
|
||||
add r11, r4, #1 @ increment it
|
||||
str r11, [r10, #TI_PREEMPT]
|
||||
|
@ -35,7 +35,7 @@ ENTRY(do_vfp)
|
|||
ENDPROC(do_vfp)
|
||||
|
||||
ENTRY(vfp_null_entry)
|
||||
#ifdef CONFIG_PREEMPT
|
||||
#ifdef CONFIG_PREEMPT_COUNT
|
||||
get_thread_info r10
|
||||
ldr r4, [r10, #TI_PREEMPT] @ get preempt count
|
||||
sub r11, r4, #1 @ decrement it
|
||||
|
@ -53,7 +53,7 @@ ENDPROC(vfp_null_entry)
|
|||
|
||||
__INIT
|
||||
ENTRY(vfp_testing_entry)
|
||||
#ifdef CONFIG_PREEMPT
|
||||
#ifdef CONFIG_PREEMPT_COUNT
|
||||
get_thread_info r10
|
||||
ldr r4, [r10, #TI_PREEMPT] @ get preempt count
|
||||
sub r11, r4, #1 @ decrement it
|
||||
|
|
|
@ -168,7 +168,7 @@ vfp_hw_state_valid:
|
|||
@ else it's one 32-bit instruction, so
|
||||
@ always subtract 4 from the following
|
||||
@ instruction address.
|
||||
#ifdef CONFIG_PREEMPT
|
||||
#ifdef CONFIG_PREEMPT_COUNT
|
||||
get_thread_info r10
|
||||
ldr r4, [r10, #TI_PREEMPT] @ get preempt count
|
||||
sub r11, r4, #1 @ decrement it
|
||||
|
@ -192,7 +192,7 @@ look_for_VFP_exceptions:
|
|||
@ not recognised by VFP
|
||||
|
||||
DBGSTR "not VFP"
|
||||
#ifdef CONFIG_PREEMPT
|
||||
#ifdef CONFIG_PREEMPT_COUNT
|
||||
get_thread_info r10
|
||||
ldr r4, [r10, #TI_PREEMPT] @ get preempt count
|
||||
sub r11, r4, #1 @ decrement it
|
||||
|
|
|
@ -26,7 +26,10 @@
|
|||
|
||||
typedef unsigned long elf_greg_t;
|
||||
|
||||
#define ELF_NGREG (sizeof (struct pt_regs) / sizeof(elf_greg_t))
|
||||
#define ELF_NGREG (sizeof(struct user_pt_regs) / sizeof(elf_greg_t))
|
||||
#define ELF_CORE_COPY_REGS(dest, regs) \
|
||||
*(struct user_pt_regs *)&(dest) = (regs)->user_regs;
|
||||
|
||||
typedef elf_greg_t elf_gregset_t[ELF_NGREG];
|
||||
typedef struct user_fpsimd_state elf_fpregset_t;
|
||||
|
||||
|
|
|
@ -672,33 +672,6 @@ ptrace_attach_sync_user_rbs (struct task_struct *child)
|
|||
read_unlock(&tasklist_lock);
|
||||
}
|
||||
|
||||
static inline int
|
||||
thread_matches (struct task_struct *thread, unsigned long addr)
|
||||
{
|
||||
unsigned long thread_rbs_end;
|
||||
struct pt_regs *thread_regs;
|
||||
|
||||
if (ptrace_check_attach(thread, 0) < 0)
|
||||
/*
|
||||
* If the thread is not in an attachable state, we'll
|
||||
* ignore it. The net effect is that if ADDR happens
|
||||
* to overlap with the portion of the thread's
|
||||
* register backing store that is currently residing
|
||||
* on the thread's kernel stack, then ptrace() may end
|
||||
* up accessing a stale value. But if the thread
|
||||
* isn't stopped, that's a problem anyhow, so we're
|
||||
* doing as well as we can...
|
||||
*/
|
||||
return 0;
|
||||
|
||||
thread_regs = task_pt_regs(thread);
|
||||
thread_rbs_end = ia64_get_user_rbs_end(thread, thread_regs, NULL);
|
||||
if (!on_kernel_rbs(addr, thread_regs->ar_bspstore, thread_rbs_end))
|
||||
return 0;
|
||||
|
||||
return 1; /* looks like we've got a winner */
|
||||
}
|
||||
|
||||
/*
|
||||
* Write f32-f127 back to task->thread.fph if it has been modified.
|
||||
*/
|
||||
|
|
|
@ -21,6 +21,22 @@ extern void *dma_alloc_coherent(struct device *, size_t,
|
|||
extern void dma_free_coherent(struct device *, size_t,
|
||||
void *, dma_addr_t);
|
||||
|
||||
static inline void *dma_alloc_attrs(struct device *dev, size_t size,
|
||||
dma_addr_t *dma_handle, gfp_t flag,
|
||||
struct dma_attrs *attrs)
|
||||
{
|
||||
/* attrs is not supported and ignored */
|
||||
return dma_alloc_coherent(dev, size, dma_handle, flag);
|
||||
}
|
||||
|
||||
static inline void dma_free_attrs(struct device *dev, size_t size,
|
||||
void *cpu_addr, dma_addr_t dma_handle,
|
||||
struct dma_attrs *attrs)
|
||||
{
|
||||
/* attrs is not supported and ignored */
|
||||
dma_free_coherent(dev, size, cpu_addr, dma_handle);
|
||||
}
|
||||
|
||||
static inline void *dma_alloc_noncoherent(struct device *dev, size_t size,
|
||||
dma_addr_t *handle, gfp_t flag)
|
||||
{
|
||||
|
|
|
@ -64,6 +64,8 @@ extern unsigned int kobjsize(const void *objp);
|
|||
*/
|
||||
#define VMALLOC_START 0
|
||||
#define VMALLOC_END 0xffffffff
|
||||
#define KMAP_START 0
|
||||
#define KMAP_END 0xffffffff
|
||||
|
||||
#include <asm-generic/pgtable.h>
|
||||
|
||||
|
|
|
@ -4,7 +4,7 @@
|
|||
#include <uapi/asm/unistd.h>
|
||||
|
||||
|
||||
#define NR_syscalls 348
|
||||
#define NR_syscalls 349
|
||||
|
||||
#define __ARCH_WANT_OLD_READDIR
|
||||
#define __ARCH_WANT_OLD_STAT
|
||||
|
|
|
@ -353,5 +353,6 @@
|
|||
#define __NR_process_vm_readv 345
|
||||
#define __NR_process_vm_writev 346
|
||||
#define __NR_kcmp 347
|
||||
#define __NR_finit_module 348
|
||||
|
||||
#endif /* _UAPI_ASM_M68K_UNISTD_H_ */
|
||||
|
|
|
@ -368,4 +368,5 @@ ENTRY(sys_call_table)
|
|||
.long sys_process_vm_readv /* 345 */
|
||||
.long sys_process_vm_writev
|
||||
.long sys_kcmp
|
||||
.long sys_finit_module
|
||||
|
||||
|
|
|
@ -39,6 +39,11 @@
|
|||
void *empty_zero_page;
|
||||
EXPORT_SYMBOL(empty_zero_page);
|
||||
|
||||
#if !defined(CONFIG_SUN3) && !defined(CONFIG_COLDFIRE)
|
||||
extern void init_pointer_table(unsigned long ptable);
|
||||
extern pmd_t *zero_pgtable;
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_MMU
|
||||
|
||||
pg_data_t pg_data_map[MAX_NUMNODES];
|
||||
|
@ -69,9 +74,6 @@ void __init m68k_setup_node(int node)
|
|||
node_set_online(node);
|
||||
}
|
||||
|
||||
extern void init_pointer_table(unsigned long ptable);
|
||||
extern pmd_t *zero_pgtable;
|
||||
|
||||
#else /* CONFIG_MMU */
|
||||
|
||||
/*
|
||||
|
|
|
@ -1865,7 +1865,7 @@ syscall_restore:
|
|||
|
||||
/* Are we being ptraced? */
|
||||
ldw TASK_FLAGS(%r1),%r19
|
||||
ldi (_TIF_SINGLESTEP|_TIF_BLOCKSTEP),%r2
|
||||
ldi _TIF_SYSCALL_TRACE_MASK,%r2
|
||||
and,COND(=) %r19,%r2,%r0
|
||||
b,n syscall_restore_rfi
|
||||
|
||||
|
@ -1978,15 +1978,23 @@ syscall_restore_rfi:
|
|||
/* sr2 should be set to zero for userspace syscalls */
|
||||
STREG %r0,TASK_PT_SR2(%r1)
|
||||
|
||||
pt_regs_ok:
|
||||
LDREG TASK_PT_GR31(%r1),%r2
|
||||
depi 3,31,2,%r2 /* ensure return to user mode. */
|
||||
STREG %r2,TASK_PT_IAOQ0(%r1)
|
||||
depi 3,31,2,%r2 /* ensure return to user mode. */
|
||||
STREG %r2,TASK_PT_IAOQ0(%r1)
|
||||
ldo 4(%r2),%r2
|
||||
STREG %r2,TASK_PT_IAOQ1(%r1)
|
||||
copy %r25,%r16
|
||||
b intr_restore
|
||||
nop
|
||||
copy %r25,%r16
|
||||
|
||||
pt_regs_ok:
|
||||
LDREG TASK_PT_IAOQ0(%r1),%r2
|
||||
depi 3,31,2,%r2 /* ensure return to user mode. */
|
||||
STREG %r2,TASK_PT_IAOQ0(%r1)
|
||||
LDREG TASK_PT_IAOQ1(%r1),%r2
|
||||
depi 3,31,2,%r2
|
||||
STREG %r2,TASK_PT_IAOQ1(%r1)
|
||||
b intr_restore
|
||||
copy %r25,%r16
|
||||
|
||||
.import schedule,code
|
||||
syscall_do_resched:
|
||||
|
|
|
@ -410,11 +410,13 @@ void __init init_IRQ(void)
|
|||
{
|
||||
local_irq_disable(); /* PARANOID - should already be disabled */
|
||||
mtctl(~0UL, 23); /* EIRR : clear all pending external intr */
|
||||
claim_cpu_irqs();
|
||||
#ifdef CONFIG_SMP
|
||||
if (!cpu_eiem)
|
||||
if (!cpu_eiem) {
|
||||
claim_cpu_irqs();
|
||||
cpu_eiem = EIEM_MASK(IPI_IRQ) | EIEM_MASK(TIMER_IRQ);
|
||||
}
|
||||
#else
|
||||
claim_cpu_irqs();
|
||||
cpu_eiem = EIEM_MASK(TIMER_IRQ);
|
||||
#endif
|
||||
set_eiem(cpu_eiem); /* EIEM : enable all external intr */
|
||||
|
|
|
@ -26,7 +26,7 @@
|
|||
#include <asm/asm-offsets.h>
|
||||
|
||||
/* PSW bits we allow the debugger to modify */
|
||||
#define USER_PSW_BITS (PSW_N | PSW_V | PSW_CB)
|
||||
#define USER_PSW_BITS (PSW_N | PSW_B | PSW_V | PSW_CB)
|
||||
|
||||
/*
|
||||
* Called by kernel/ptrace.c when detaching..
|
||||
|
|
|
@ -190,8 +190,10 @@ get_sigframe(struct k_sigaction *ka, unsigned long sp, size_t frame_size)
|
|||
DBG(1,"get_sigframe: ka = %#lx, sp = %#lx, frame_size = %#lx\n",
|
||||
(unsigned long)ka, sp, frame_size);
|
||||
|
||||
/* Align alternate stack and reserve 64 bytes for the signal
|
||||
handler's frame marker. */
|
||||
if ((ka->sa.sa_flags & SA_ONSTACK) != 0 && ! sas_ss_flags(sp))
|
||||
sp = current->sas_ss_sp; /* Stacks grow up! */
|
||||
sp = (current->sas_ss_sp + 0x7f) & ~0x3f; /* Stacks grow up! */
|
||||
|
||||
DBG(1,"get_sigframe: Returning sp = %#lx\n", (unsigned long)sp);
|
||||
return (void __user *) sp; /* Stacks grow up. Fun. */
|
||||
|
|
|
@ -347,16 +347,15 @@
|
|||
Sgl_isinexact_to_fix(sgl_value,exponent)
|
||||
|
||||
#define Duint_from_sgl_mantissa(sgl_value,exponent,dresultA,dresultB) \
|
||||
{Sall(sgl_value) <<= SGL_EXP_LENGTH; /* left-justify */ \
|
||||
{unsigned int val = Sall(sgl_value) << SGL_EXP_LENGTH; \
|
||||
if (exponent <= 31) { \
|
||||
Dintp1(dresultA) = 0; \
|
||||
Dintp2(dresultB) = (unsigned)Sall(sgl_value) >> (31 - exponent); \
|
||||
Dintp1(dresultA) = 0; \
|
||||
Dintp2(dresultB) = val >> (31 - exponent); \
|
||||
} \
|
||||
else { \
|
||||
Dintp1(dresultA) = Sall(sgl_value) >> (63 - exponent); \
|
||||
Dintp2(dresultB) = Sall(sgl_value) << (exponent - 31); \
|
||||
Dintp1(dresultA) = val >> (63 - exponent); \
|
||||
Dintp2(dresultB) = exponent <= 62 ? val << (exponent - 31) : 0; \
|
||||
} \
|
||||
Sall(sgl_value) >>= SGL_EXP_LENGTH; /* return to original */ \
|
||||
}
|
||||
|
||||
#define Duint_setzero(dresultA,dresultB) \
|
||||
|
|
|
@ -439,6 +439,8 @@ ret_from_fork:
|
|||
ret_from_kernel_thread:
|
||||
REST_NVGPRS(r1)
|
||||
bl schedule_tail
|
||||
li r3,0
|
||||
stw r3,0(r1)
|
||||
mtlr r14
|
||||
mr r3,r15
|
||||
PPC440EP_ERR42
|
||||
|
|
|
@ -664,6 +664,19 @@ resume_kernel:
|
|||
ld r4,TI_FLAGS(r9)
|
||||
andi. r0,r4,_TIF_NEED_RESCHED
|
||||
bne 1b
|
||||
|
||||
/*
|
||||
* arch_local_irq_restore() from preempt_schedule_irq above may
|
||||
* enable hard interrupt but we really should disable interrupts
|
||||
* when we return from the interrupt, and so that we don't get
|
||||
* interrupted after loading SRR0/1.
|
||||
*/
|
||||
#ifdef CONFIG_PPC_BOOK3E
|
||||
wrteei 0
|
||||
#else
|
||||
ld r10,PACAKMSR(r13) /* Get kernel MSR without EE */
|
||||
mtmsrd r10,1 /* Update machine state */
|
||||
#endif /* CONFIG_PPC_BOOK3E */
|
||||
#endif /* CONFIG_PREEMPT */
|
||||
|
||||
.globl fast_exc_return_irq
|
||||
|
|
|
@ -154,12 +154,12 @@ static int kgdb_handle_breakpoint(struct pt_regs *regs)
|
|||
static int kgdb_singlestep(struct pt_regs *regs)
|
||||
{
|
||||
struct thread_info *thread_info, *exception_thread_info;
|
||||
struct thread_info *backup_current_thread_info = \
|
||||
(struct thread_info *)kmalloc(sizeof(struct thread_info), GFP_KERNEL);
|
||||
struct thread_info *backup_current_thread_info;
|
||||
|
||||
if (user_mode(regs))
|
||||
return 0;
|
||||
|
||||
backup_current_thread_info = (struct thread_info *)kmalloc(sizeof(struct thread_info), GFP_KERNEL);
|
||||
/*
|
||||
* On Book E and perhaps other processors, singlestep is handled on
|
||||
* the critical exception stack. This causes current_thread_info()
|
||||
|
@ -185,6 +185,7 @@ static int kgdb_singlestep(struct pt_regs *regs)
|
|||
/* Restore current_thread_info lastly. */
|
||||
memcpy(exception_thread_info, backup_current_thread_info, sizeof *thread_info);
|
||||
|
||||
kfree(backup_current_thread_info);
|
||||
return 1;
|
||||
}
|
||||
|
||||
|
|
|
@ -494,10 +494,15 @@ void timer_interrupt(struct pt_regs * regs)
|
|||
set_dec(DECREMENTER_MAX);
|
||||
|
||||
/* Some implementations of hotplug will get timer interrupts while
|
||||
* offline, just ignore these
|
||||
* offline, just ignore these and we also need to set
|
||||
* decrementers_next_tb as MAX to make sure __check_irq_replay
|
||||
* don't replay timer interrupt when return, otherwise we'll trap
|
||||
* here infinitely :(
|
||||
*/
|
||||
if (!cpu_online(smp_processor_id()))
|
||||
if (!cpu_online(smp_processor_id())) {
|
||||
*next_tb = ~(u64)0;
|
||||
return;
|
||||
}
|
||||
|
||||
/* Conditionally hard-enable interrupts now that the DEC has been
|
||||
* bumped to its maximum value
|
||||
|
|
|
@ -39,6 +39,7 @@
|
|||
#define OP_31_XOP_TRAP 4
|
||||
#define OP_31_XOP_LWZX 23
|
||||
#define OP_31_XOP_TRAP_64 68
|
||||
#define OP_31_XOP_DCBF 86
|
||||
#define OP_31_XOP_LBZX 87
|
||||
#define OP_31_XOP_STWX 151
|
||||
#define OP_31_XOP_STBX 215
|
||||
|
@ -374,6 +375,7 @@ int kvmppc_emulate_instruction(struct kvm_run *run, struct kvm_vcpu *vcpu)
|
|||
emulated = kvmppc_emulate_mtspr(vcpu, sprn, rs);
|
||||
break;
|
||||
|
||||
case OP_31_XOP_DCBF:
|
||||
case OP_31_XOP_DCBI:
|
||||
/* Do nothing. The guest is performing dcbi because
|
||||
* hardware DMA is not snooped by the dcache, but
|
||||
|
|
|
@ -52,7 +52,7 @@ static int power7_marked_instr_event(u64 mmcr1)
|
|||
for (pmc = 0; pmc < 4; pmc++) {
|
||||
psel = mmcr1 & (OPROFILE_PM_PMCSEL_MSK
|
||||
<< (OPROFILE_MAX_PMC_NUM - pmc)
|
||||
* OPROFILE_MAX_PMC_NUM);
|
||||
* OPROFILE_PMSEL_FIELD_WIDTH);
|
||||
psel = (psel >> ((OPROFILE_MAX_PMC_NUM - pmc)
|
||||
* OPROFILE_PMSEL_FIELD_WIDTH)) & ~1ULL;
|
||||
unit = mmcr1 & (OPROFILE_PM_UNIT_MSK
|
||||
|
|
|
@ -236,6 +236,13 @@ static int pas_cpufreq_cpu_init(struct cpufreq_policy *policy)
|
|||
|
||||
static int pas_cpufreq_cpu_exit(struct cpufreq_policy *policy)
|
||||
{
|
||||
/*
|
||||
* We don't support CPU hotplug. Don't unmap after the system
|
||||
* has already made it to a running state.
|
||||
*/
|
||||
if (system_state != SYSTEM_BOOTING)
|
||||
return 0;
|
||||
|
||||
if (sdcasr_mapbase)
|
||||
iounmap(sdcasr_mapbase);
|
||||
if (sdcpwr_mapbase)
|
||||
|
|
|
@ -1365,6 +1365,18 @@ static inline void pmdp_invalidate(struct vm_area_struct *vma,
|
|||
__pmd_idte(address, pmdp);
|
||||
}
|
||||
|
||||
#define __HAVE_ARCH_PMDP_SET_WRPROTECT
|
||||
static inline void pmdp_set_wrprotect(struct mm_struct *mm,
|
||||
unsigned long address, pmd_t *pmdp)
|
||||
{
|
||||
pmd_t pmd = *pmdp;
|
||||
|
||||
if (pmd_write(pmd)) {
|
||||
__pmd_idte(address, pmdp);
|
||||
set_pmd_at(mm, address, pmdp, pmd_wrprotect(pmd));
|
||||
}
|
||||
}
|
||||
|
||||
static inline pmd_t mk_pmd_phys(unsigned long physpage, pgprot_t pgprot)
|
||||
{
|
||||
pmd_t __pmd;
|
||||
|
|
|
@ -2138,6 +2138,7 @@ config OLPC_XO1_RTC
|
|||
config OLPC_XO1_SCI
|
||||
bool "OLPC XO-1 SCI extras"
|
||||
depends on OLPC && OLPC_XO1_PM
|
||||
depends on INPUT=y
|
||||
select POWER_SUPPLY
|
||||
select GPIO_CS5535
|
||||
select MFD_CORE
|
||||
|
|
|
@ -71,7 +71,7 @@ GCOV_PROFILE := n
|
|||
$(obj)/bzImage: asflags-y := $(SVGA_MODE)
|
||||
|
||||
quiet_cmd_image = BUILD $@
|
||||
cmd_image = $(obj)/tools/build $(obj)/setup.bin $(obj)/vmlinux.bin > $@
|
||||
cmd_image = $(obj)/tools/build $(obj)/setup.bin $(obj)/vmlinux.bin $(obj)/zoffset.h > $@
|
||||
|
||||
$(obj)/bzImage: $(obj)/setup.bin $(obj)/vmlinux.bin $(obj)/tools/build FORCE
|
||||
$(call if_changed,image)
|
||||
|
@ -92,7 +92,7 @@ targets += voffset.h
|
|||
$(obj)/voffset.h: vmlinux FORCE
|
||||
$(call if_changed,voffset)
|
||||
|
||||
sed-zoffset := -e 's/^\([0-9a-fA-F]*\) . \(startup_32\|input_data\|_end\|z_.*\)$$/\#define ZO_\2 0x\1/p'
|
||||
sed-zoffset := -e 's/^\([0-9a-fA-F]*\) . \(startup_32\|startup_64\|efi_pe_entry\|efi_stub_entry\|input_data\|_end\|z_.*\)$$/\#define ZO_\2 0x\1/p'
|
||||
|
||||
quiet_cmd_zoffset = ZOFFSET $@
|
||||
cmd_zoffset = $(NM) $< | sed -n $(sed-zoffset) > $@
|
||||
|
|
|
@ -256,10 +256,10 @@ static efi_status_t setup_efi_pci(struct boot_params *params)
|
|||
int i;
|
||||
struct setup_data *data;
|
||||
|
||||
data = (struct setup_data *)params->hdr.setup_data;
|
||||
data = (struct setup_data *)(unsigned long)params->hdr.setup_data;
|
||||
|
||||
while (data && data->next)
|
||||
data = (struct setup_data *)data->next;
|
||||
data = (struct setup_data *)(unsigned long)data->next;
|
||||
|
||||
status = efi_call_phys5(sys_table->boottime->locate_handle,
|
||||
EFI_LOCATE_BY_PROTOCOL, &pci_proto,
|
||||
|
@ -295,16 +295,18 @@ static efi_status_t setup_efi_pci(struct boot_params *params)
|
|||
if (!pci)
|
||||
continue;
|
||||
|
||||
#ifdef CONFIG_X86_64
|
||||
status = efi_call_phys4(pci->attributes, pci,
|
||||
EfiPciIoAttributeOperationGet, 0,
|
||||
&attributes);
|
||||
|
||||
#else
|
||||
status = efi_call_phys5(pci->attributes, pci,
|
||||
EfiPciIoAttributeOperationGet, 0, 0,
|
||||
&attributes);
|
||||
#endif
|
||||
if (status != EFI_SUCCESS)
|
||||
continue;
|
||||
|
||||
if (!(attributes & EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM))
|
||||
continue;
|
||||
|
||||
if (!pci->romimage || !pci->romsize)
|
||||
continue;
|
||||
|
||||
|
@ -345,9 +347,9 @@ static efi_status_t setup_efi_pci(struct boot_params *params)
|
|||
memcpy(rom->romdata, pci->romimage, pci->romsize);
|
||||
|
||||
if (data)
|
||||
data->next = (uint64_t)rom;
|
||||
data->next = (unsigned long)rom;
|
||||
else
|
||||
params->hdr.setup_data = (uint64_t)rom;
|
||||
params->hdr.setup_data = (unsigned long)rom;
|
||||
|
||||
data = (struct setup_data *)rom;
|
||||
|
||||
|
@ -432,10 +434,9 @@ static efi_status_t setup_gop(struct screen_info *si, efi_guid_t *proto,
|
|||
* Once we've found a GOP supporting ConOut,
|
||||
* don't bother looking any further.
|
||||
*/
|
||||
first_gop = gop;
|
||||
if (conout_found)
|
||||
break;
|
||||
|
||||
first_gop = gop;
|
||||
}
|
||||
}
|
||||
|
||||
|
|
|
@ -35,11 +35,11 @@ ENTRY(startup_32)
|
|||
#ifdef CONFIG_EFI_STUB
|
||||
jmp preferred_addr
|
||||
|
||||
.balign 0x10
|
||||
/*
|
||||
* We don't need the return address, so set up the stack so
|
||||
* efi_main() can find its arugments.
|
||||
* efi_main() can find its arguments.
|
||||
*/
|
||||
ENTRY(efi_pe_entry)
|
||||
add $0x4, %esp
|
||||
|
||||
call make_boot_params
|
||||
|
@ -50,8 +50,10 @@ ENTRY(startup_32)
|
|||
pushl %eax
|
||||
pushl %esi
|
||||
pushl %ecx
|
||||
sub $0x4, %esp
|
||||
|
||||
.org 0x30,0x90
|
||||
ENTRY(efi_stub_entry)
|
||||
add $0x4, %esp
|
||||
call efi_main
|
||||
cmpl $0, %eax
|
||||
movl %eax, %esi
|
||||
|
|
|
@ -201,12 +201,12 @@ ENTRY(startup_64)
|
|||
*/
|
||||
#ifdef CONFIG_EFI_STUB
|
||||
/*
|
||||
* The entry point for the PE/COFF executable is 0x210, so only
|
||||
* legacy boot loaders will execute this jmp.
|
||||
* The entry point for the PE/COFF executable is efi_pe_entry, so
|
||||
* only legacy boot loaders will execute this jmp.
|
||||
*/
|
||||
jmp preferred_addr
|
||||
|
||||
.org 0x210
|
||||
ENTRY(efi_pe_entry)
|
||||
mov %rcx, %rdi
|
||||
mov %rdx, %rsi
|
||||
pushq %rdi
|
||||
|
@ -218,7 +218,7 @@ ENTRY(startup_64)
|
|||
popq %rsi
|
||||
popq %rdi
|
||||
|
||||
.org 0x230,0x90
|
||||
ENTRY(efi_stub_entry)
|
||||
call efi_main
|
||||
movq %rax,%rsi
|
||||
cmpq $0,%rax
|
||||
|
|
|
@ -21,6 +21,7 @@
|
|||
#include <asm/e820.h>
|
||||
#include <asm/page_types.h>
|
||||
#include <asm/setup.h>
|
||||
#include <asm/bootparam.h>
|
||||
#include "boot.h"
|
||||
#include "voffset.h"
|
||||
#include "zoffset.h"
|
||||
|
@ -255,6 +256,9 @@ section_table:
|
|||
# header, from the old boot sector.
|
||||
|
||||
.section ".header", "a"
|
||||
.globl sentinel
|
||||
sentinel: .byte 0xff, 0xff /* Used to detect broken loaders */
|
||||
|
||||
.globl hdr
|
||||
hdr:
|
||||
setup_sects: .byte 0 /* Filled in by build.c */
|
||||
|
@ -279,7 +283,7 @@ _start:
|
|||
# Part 2 of the header, from the old setup.S
|
||||
|
||||
.ascii "HdrS" # header signature
|
||||
.word 0x020b # header version number (>= 0x0105)
|
||||
.word 0x020c # header version number (>= 0x0105)
|
||||
# or else old loadlin-1.5 will fail)
|
||||
.globl realmode_swtch
|
||||
realmode_swtch: .word 0, 0 # default_switch, SETUPSEG
|
||||
|
@ -297,13 +301,7 @@ type_of_loader: .byte 0 # 0 means ancient bootloader, newer
|
|||
|
||||
# flags, unused bits must be zero (RFU) bit within loadflags
|
||||
loadflags:
|
||||
LOADED_HIGH = 1 # If set, the kernel is loaded high
|
||||
CAN_USE_HEAP = 0x80 # If set, the loader also has set
|
||||
# heap_end_ptr to tell how much
|
||||
# space behind setup.S can be used for
|
||||
# heap purposes.
|
||||
# Only the loader knows what is free
|
||||
.byte LOADED_HIGH
|
||||
.byte LOADED_HIGH # The kernel is to be loaded high
|
||||
|
||||
setup_move_size: .word 0x8000 # size to move, when setup is not
|
||||
# loaded at 0x90000. We will move setup
|
||||
|
@ -369,7 +367,23 @@ relocatable_kernel: .byte 1
|
|||
relocatable_kernel: .byte 0
|
||||
#endif
|
||||
min_alignment: .byte MIN_KERNEL_ALIGN_LG2 # minimum alignment
|
||||
pad3: .word 0
|
||||
|
||||
xloadflags:
|
||||
#ifdef CONFIG_X86_64
|
||||
# define XLF0 XLF_KERNEL_64 /* 64-bit kernel */
|
||||
#else
|
||||
# define XLF0 0
|
||||
#endif
|
||||
#ifdef CONFIG_EFI_STUB
|
||||
# ifdef CONFIG_X86_64
|
||||
# define XLF23 XLF_EFI_HANDOVER_64 /* 64-bit EFI handover ok */
|
||||
# else
|
||||
# define XLF23 XLF_EFI_HANDOVER_32 /* 32-bit EFI handover ok */
|
||||
# endif
|
||||
#else
|
||||
# define XLF23 0
|
||||
#endif
|
||||
.word XLF0 | XLF23
|
||||
|
||||
cmdline_size: .long COMMAND_LINE_SIZE-1 #length of the command line,
|
||||
#added with boot protocol
|
||||
|
@ -397,8 +411,13 @@ pref_address: .quad LOAD_PHYSICAL_ADDR # preferred load addr
|
|||
#define INIT_SIZE VO_INIT_SIZE
|
||||
#endif
|
||||
init_size: .long INIT_SIZE # kernel initialization size
|
||||
handover_offset: .long 0x30 # offset to the handover
|
||||
handover_offset:
|
||||
#ifdef CONFIG_EFI_STUB
|
||||
.long 0x30 # offset to the handover
|
||||
# protocol entry point
|
||||
#else
|
||||
.long 0
|
||||
#endif
|
||||
|
||||
# End of setup header #####################################################
|
||||
|
||||
|
|
|
@ -13,7 +13,7 @@ SECTIONS
|
|||
.bstext : { *(.bstext) }
|
||||
.bsdata : { *(.bsdata) }
|
||||
|
||||
. = 497;
|
||||
. = 495;
|
||||
.header : { *(.header) }
|
||||
.entrytext : { *(.entrytext) }
|
||||
.inittext : { *(.inittext) }
|
||||
|
|
|
@ -52,6 +52,10 @@ int is_big_kernel;
|
|||
|
||||
#define PECOFF_RELOC_RESERVE 0x20
|
||||
|
||||
unsigned long efi_stub_entry;
|
||||
unsigned long efi_pe_entry;
|
||||
unsigned long startup_64;
|
||||
|
||||
/*----------------------------------------------------------------------*/
|
||||
|
||||
static const u32 crctab32[] = {
|
||||
|
@ -132,7 +136,7 @@ static void die(const char * str, ...)
|
|||
|
||||
static void usage(void)
|
||||
{
|
||||
die("Usage: build setup system [> image]");
|
||||
die("Usage: build setup system [zoffset.h] [> image]");
|
||||
}
|
||||
|
||||
#ifdef CONFIG_EFI_STUB
|
||||
|
@ -206,30 +210,54 @@ static void update_pecoff_text(unsigned int text_start, unsigned int file_sz)
|
|||
*/
|
||||
put_unaligned_le32(file_sz - 512, &buf[pe_header + 0x1c]);
|
||||
|
||||
#ifdef CONFIG_X86_32
|
||||
/*
|
||||
* Address of entry point.
|
||||
*
|
||||
* The EFI stub entry point is +16 bytes from the start of
|
||||
* the .text section.
|
||||
* Address of entry point for PE/COFF executable
|
||||
*/
|
||||
put_unaligned_le32(text_start + 16, &buf[pe_header + 0x28]);
|
||||
#else
|
||||
/*
|
||||
* Address of entry point. startup_32 is at the beginning and
|
||||
* the 64-bit entry point (startup_64) is always 512 bytes
|
||||
* after. The EFI stub entry point is 16 bytes after that, as
|
||||
* the first instruction allows legacy loaders to jump over
|
||||
* the EFI stub initialisation
|
||||
*/
|
||||
put_unaligned_le32(text_start + 528, &buf[pe_header + 0x28]);
|
||||
#endif /* CONFIG_X86_32 */
|
||||
put_unaligned_le32(text_start + efi_pe_entry, &buf[pe_header + 0x28]);
|
||||
|
||||
update_pecoff_section_header(".text", text_start, text_sz);
|
||||
}
|
||||
|
||||
#endif /* CONFIG_EFI_STUB */
|
||||
|
||||
|
||||
/*
|
||||
* Parse zoffset.h and find the entry points. We could just #include zoffset.h
|
||||
* but that would mean tools/build would have to be rebuilt every time. It's
|
||||
* not as if parsing it is hard...
|
||||
*/
|
||||
#define PARSE_ZOFS(p, sym) do { \
|
||||
if (!strncmp(p, "#define ZO_" #sym " ", 11+sizeof(#sym))) \
|
||||
sym = strtoul(p + 11 + sizeof(#sym), NULL, 16); \
|
||||
} while (0)
|
||||
|
||||
static void parse_zoffset(char *fname)
|
||||
{
|
||||
FILE *file;
|
||||
char *p;
|
||||
int c;
|
||||
|
||||
file = fopen(fname, "r");
|
||||
if (!file)
|
||||
die("Unable to open `%s': %m", fname);
|
||||
c = fread(buf, 1, sizeof(buf) - 1, file);
|
||||
if (ferror(file))
|
||||
die("read-error on `zoffset.h'");
|
||||
buf[c] = 0;
|
||||
|
||||
p = (char *)buf;
|
||||
|
||||
while (p && *p) {
|
||||
PARSE_ZOFS(p, efi_stub_entry);
|
||||
PARSE_ZOFS(p, efi_pe_entry);
|
||||
PARSE_ZOFS(p, startup_64);
|
||||
|
||||
p = strchr(p, '\n');
|
||||
while (p && (*p == '\r' || *p == '\n'))
|
||||
p++;
|
||||
}
|
||||
}
|
||||
|
||||
int main(int argc, char ** argv)
|
||||
{
|
||||
unsigned int i, sz, setup_sectors;
|
||||
|
@ -241,7 +269,19 @@ int main(int argc, char ** argv)
|
|||
void *kernel;
|
||||
u32 crc = 0xffffffffUL;
|
||||
|
||||
if (argc != 3)
|
||||
/* Defaults for old kernel */
|
||||
#ifdef CONFIG_X86_32
|
||||
efi_pe_entry = 0x10;
|
||||
efi_stub_entry = 0x30;
|
||||
#else
|
||||
efi_pe_entry = 0x210;
|
||||
efi_stub_entry = 0x230;
|
||||
startup_64 = 0x200;
|
||||
#endif
|
||||
|
||||
if (argc == 4)
|
||||
parse_zoffset(argv[3]);
|
||||
else if (argc != 3)
|
||||
usage();
|
||||
|
||||
/* Copy the setup code */
|
||||
|
@ -299,6 +339,11 @@ int main(int argc, char ** argv)
|
|||
|
||||
#ifdef CONFIG_EFI_STUB
|
||||
update_pecoff_text(setup_sectors * 512, sz + i + ((sys_size * 16) - sz));
|
||||
|
||||
#ifdef CONFIG_X86_64 /* Yes, this is really how we defined it :( */
|
||||
efi_stub_entry -= 0x200;
|
||||
#endif
|
||||
put_unaligned_le32(efi_stub_entry, &buf[0x264]);
|
||||
#endif
|
||||
|
||||
crc = partial_crc32(buf, i, crc);
|
||||
|
|
|
@ -94,6 +94,7 @@ extern void __iomem *efi_ioremap(unsigned long addr, unsigned long size,
|
|||
#endif /* CONFIG_X86_32 */
|
||||
|
||||
extern int add_efi_memmap;
|
||||
extern unsigned long x86_efi_facility;
|
||||
extern void efi_set_executable(efi_memory_desc_t *md, bool executable);
|
||||
extern int efi_memblock_x86_reserve_range(void);
|
||||
extern void efi_call_phys_prelog(void);
|
||||
|
|
|
@ -16,7 +16,7 @@ extern void uv_system_init(void);
|
|||
extern const struct cpumask *uv_flush_tlb_others(const struct cpumask *cpumask,
|
||||
struct mm_struct *mm,
|
||||
unsigned long start,
|
||||
unsigned end,
|
||||
unsigned long end,
|
||||
unsigned int cpu);
|
||||
|
||||
#else /* X86_UV */
|
||||
|
|
|
@ -1,6 +1,31 @@
|
|||
#ifndef _ASM_X86_BOOTPARAM_H
|
||||
#define _ASM_X86_BOOTPARAM_H
|
||||
|
||||
/* setup_data types */
|
||||
#define SETUP_NONE 0
|
||||
#define SETUP_E820_EXT 1
|
||||
#define SETUP_DTB 2
|
||||
#define SETUP_PCI 3
|
||||
|
||||
/* ram_size flags */
|
||||
#define RAMDISK_IMAGE_START_MASK 0x07FF
|
||||
#define RAMDISK_PROMPT_FLAG 0x8000
|
||||
#define RAMDISK_LOAD_FLAG 0x4000
|
||||
|
||||
/* loadflags */
|
||||
#define LOADED_HIGH (1<<0)
|
||||
#define QUIET_FLAG (1<<5)
|
||||
#define KEEP_SEGMENTS (1<<6)
|
||||
#define CAN_USE_HEAP (1<<7)
|
||||
|
||||
/* xloadflags */
|
||||
#define XLF_KERNEL_64 (1<<0)
|
||||
#define XLF_CAN_BE_LOADED_ABOVE_4G (1<<1)
|
||||
#define XLF_EFI_HANDOVER_32 (1<<2)
|
||||
#define XLF_EFI_HANDOVER_64 (1<<3)
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
#include <linux/types.h>
|
||||
#include <linux/screen_info.h>
|
||||
#include <linux/apm_bios.h>
|
||||
|
@ -9,12 +34,6 @@
|
|||
#include <asm/ist.h>
|
||||
#include <video/edid.h>
|
||||
|
||||
/* setup data types */
|
||||
#define SETUP_NONE 0
|
||||
#define SETUP_E820_EXT 1
|
||||
#define SETUP_DTB 2
|
||||
#define SETUP_PCI 3
|
||||
|
||||
/* extensible setup data list node */
|
||||
struct setup_data {
|
||||
__u64 next;
|
||||
|
@ -28,9 +47,6 @@ struct setup_header {
|
|||
__u16 root_flags;
|
||||
__u32 syssize;
|
||||
__u16 ram_size;
|
||||
#define RAMDISK_IMAGE_START_MASK 0x07FF
|
||||
#define RAMDISK_PROMPT_FLAG 0x8000
|
||||
#define RAMDISK_LOAD_FLAG 0x4000
|
||||
__u16 vid_mode;
|
||||
__u16 root_dev;
|
||||
__u16 boot_flag;
|
||||
|
@ -42,10 +58,6 @@ struct setup_header {
|
|||
__u16 kernel_version;
|
||||
__u8 type_of_loader;
|
||||
__u8 loadflags;
|
||||
#define LOADED_HIGH (1<<0)
|
||||
#define QUIET_FLAG (1<<5)
|
||||
#define KEEP_SEGMENTS (1<<6)
|
||||
#define CAN_USE_HEAP (1<<7)
|
||||
__u16 setup_move_size;
|
||||
__u32 code32_start;
|
||||
__u32 ramdisk_image;
|
||||
|
@ -58,7 +70,8 @@ struct setup_header {
|
|||
__u32 initrd_addr_max;
|
||||
__u32 kernel_alignment;
|
||||
__u8 relocatable_kernel;
|
||||
__u8 _pad2[3];
|
||||
__u8 min_alignment;
|
||||
__u16 xloadflags;
|
||||
__u32 cmdline_size;
|
||||
__u32 hardware_subarch;
|
||||
__u64 hardware_subarch_data;
|
||||
|
@ -106,7 +119,10 @@ struct boot_params {
|
|||
__u8 hd1_info[16]; /* obsolete! */ /* 0x090 */
|
||||
struct sys_desc_table sys_desc_table; /* 0x0a0 */
|
||||
struct olpc_ofw_header olpc_ofw_header; /* 0x0b0 */
|
||||
__u8 _pad4[128]; /* 0x0c0 */
|
||||
__u32 ext_ramdisk_image; /* 0x0c0 */
|
||||
__u32 ext_ramdisk_size; /* 0x0c4 */
|
||||
__u32 ext_cmd_line_ptr; /* 0x0c8 */
|
||||
__u8 _pad4[116]; /* 0x0cc */
|
||||
struct edid_info edid_info; /* 0x140 */
|
||||
struct efi_info efi_info; /* 0x1c0 */
|
||||
__u32 alt_mem_k; /* 0x1e0 */
|
||||
|
@ -115,7 +131,20 @@ struct boot_params {
|
|||
__u8 eddbuf_entries; /* 0x1e9 */
|
||||
__u8 edd_mbr_sig_buf_entries; /* 0x1ea */
|
||||
__u8 kbd_status; /* 0x1eb */
|
||||
__u8 _pad6[5]; /* 0x1ec */
|
||||
__u8 _pad5[3]; /* 0x1ec */
|
||||
/*
|
||||
* The sentinel is set to a nonzero value (0xff) in header.S.
|
||||
*
|
||||
* A bootloader is supposed to only take setup_header and put
|
||||
* it into a clean boot_params buffer. If it turns out that
|
||||
* it is clumsy or too generous with the buffer, it most
|
||||
* probably will pick up the sentinel variable too. The fact
|
||||
* that this variable then is still 0xff will let kernel
|
||||
* know that some variables in boot_params are invalid and
|
||||
* kernel should zero out certain portions of boot_params.
|
||||
*/
|
||||
__u8 sentinel; /* 0x1ef */
|
||||
__u8 _pad6[1]; /* 0x1f0 */
|
||||
struct setup_header hdr; /* setup header */ /* 0x1f1 */
|
||||
__u8 _pad7[0x290-0x1f1-sizeof(struct setup_header)];
|
||||
__u32 edd_mbr_sig_buffer[EDD_MBR_SIG_MAX]; /* 0x290 */
|
||||
|
@ -134,6 +163,6 @@ enum {
|
|||
X86_NR_SUBARCHS,
|
||||
};
|
||||
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
|
||||
#endif /* _ASM_X86_BOOTPARAM_H */
|
||||
|
|
|
@ -340,9 +340,6 @@ int x86_setup_perfctr(struct perf_event *event)
|
|||
/* BTS is currently only allowed for user-mode. */
|
||||
if (!attr->exclude_kernel)
|
||||
return -EOPNOTSUPP;
|
||||
|
||||
if (!attr->exclude_guest)
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
|
||||
hwc->config |= config;
|
||||
|
@ -385,9 +382,6 @@ int x86_pmu_hw_config(struct perf_event *event)
|
|||
if (event->attr.precise_ip) {
|
||||
int precise = 0;
|
||||
|
||||
if (!event->attr.exclude_guest)
|
||||
return -EOPNOTSUPP;
|
||||
|
||||
/* Support for constant skid */
|
||||
if (x86_pmu.pebs_active && !x86_pmu.pebs_broken) {
|
||||
precise++;
|
||||
|
|
|
@ -1065,7 +1065,6 @@ ENTRY(xen_failsafe_callback)
|
|||
lea 16(%esp),%esp
|
||||
CFI_ADJUST_CFA_OFFSET -16
|
||||
jz 5f
|
||||
addl $16,%esp
|
||||
jmp iret_exc
|
||||
5: pushl_cfi $-1 /* orig_ax = -1 => not a system call */
|
||||
SAVE_ALL
|
||||
|
|
|
@ -1781,6 +1781,7 @@ first_nmi:
|
|||
* Leave room for the "copied" frame
|
||||
*/
|
||||
subq $(5*8), %rsp
|
||||
CFI_ADJUST_CFA_OFFSET 5*8
|
||||
|
||||
/* Copy the stack frame to the Saved frame */
|
||||
.rept 5
|
||||
|
@ -1863,10 +1864,8 @@ end_repeat_nmi:
|
|||
nmi_swapgs:
|
||||
SWAPGS_UNSAFE_STACK
|
||||
nmi_restore:
|
||||
RESTORE_ALL 8
|
||||
|
||||
/* Pop the extra iret frame */
|
||||
addq $(5*8), %rsp
|
||||
/* Pop the extra iret frame at once */
|
||||
RESTORE_ALL 6*8
|
||||
|
||||
/* Clear the NMI executing stack variable */
|
||||
movq $0, 5*8(%rsp)
|
||||
|
|
|
@ -300,6 +300,12 @@ ENTRY(startup_32_smp)
|
|||
leal -__PAGE_OFFSET(%ecx),%esp
|
||||
|
||||
default_entry:
|
||||
#define CR0_STATE (X86_CR0_PE | X86_CR0_MP | X86_CR0_ET | \
|
||||
X86_CR0_NE | X86_CR0_WP | X86_CR0_AM | \
|
||||
X86_CR0_PG)
|
||||
movl $(CR0_STATE & ~X86_CR0_PG),%eax
|
||||
movl %eax,%cr0
|
||||
|
||||
/*
|
||||
* New page tables may be in 4Mbyte page mode and may
|
||||
* be using the global pages.
|
||||
|
@ -364,8 +370,7 @@ default_entry:
|
|||
*/
|
||||
movl $pa(initial_page_table), %eax
|
||||
movl %eax,%cr3 /* set the page table pointer.. */
|
||||
movl %cr0,%eax
|
||||
orl $X86_CR0_PG,%eax
|
||||
movl $CR0_STATE,%eax
|
||||
movl %eax,%cr0 /* ..and set paging (PG) bit */
|
||||
ljmp $__BOOT_CS,$1f /* Clear prefetch and normalize %eip */
|
||||
1:
|
||||
|
|
|
@ -174,6 +174,9 @@ static int msr_open(struct inode *inode, struct file *file)
|
|||
unsigned int cpu;
|
||||
struct cpuinfo_x86 *c;
|
||||
|
||||
if (!capable(CAP_SYS_RAWIO))
|
||||
return -EPERM;
|
||||
|
||||
cpu = iminor(file->f_path.dentry->d_inode);
|
||||
if (cpu >= nr_cpu_ids || !cpu_online(cpu))
|
||||
return -ENXIO; /* No such CPU */
|
||||
|
|
|
@ -56,7 +56,7 @@ struct device x86_dma_fallback_dev = {
|
|||
EXPORT_SYMBOL(x86_dma_fallback_dev);
|
||||
|
||||
/* Number of entries preallocated for DMA-API debugging */
|
||||
#define PREALLOC_DMA_DEBUG_ENTRIES 32768
|
||||
#define PREALLOC_DMA_DEBUG_ENTRIES 65536
|
||||
|
||||
int dma_set_mask(struct device *dev, u64 mask)
|
||||
{
|
||||
|
|
|
@ -584,7 +584,7 @@ static void native_machine_emergency_restart(void)
|
|||
break;
|
||||
|
||||
case BOOT_EFI:
|
||||
if (efi_enabled)
|
||||
if (efi_enabled(EFI_RUNTIME_SERVICES))
|
||||
efi.reset_system(reboot_mode ?
|
||||
EFI_RESET_WARM :
|
||||
EFI_RESET_COLD,
|
||||
|
|
Some files were not shown because too many files have changed in this diff Show More
Loading…
Reference in New Issue