davinci: dm365: add NAND support to EVM board

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This commit is contained in:
Sandeep Paulraj 2009-06-20 14:15:51 -04:00 committed by Kevin Hilman
parent a45c8ba30b
commit 37b798da5d
1 changed files with 84 additions and 0 deletions

View File

@ -20,6 +20,9 @@
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/i2c/at24.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@ -34,10 +37,84 @@
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/mmc.h>
#include <mach/nand.h>
#define DM365_ASYNC_EMIF_CONTROL_BASE 0x01d10000
#define DM365_ASYNC_EMIF_DATA_CE0_BASE 0x02000000
#define DM365_EVM_PHY_MASK (0x2)
#define DM365_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
/* NOTE: this is geared for the standard config, with a socketed
* 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you
* swap chips with a different block size, partitioning will
* need to be changed. This NAND chip MT29F16G08FAA is the default
* NAND shipped with the Spectrum Digital DM365 EVM
*/
#define NAND_BLOCK_SIZE SZ_128K
static struct mtd_partition davinci_nand_partitions[] = {
{
/* UBL (a few copies) plus U-Boot */
.name = "bootloader",
.offset = 0,
.size = 28 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
/* U-Boot environment */
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = 2 * NAND_BLOCK_SIZE,
.mask_flags = 0,
}, {
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_4M,
.mask_flags = 0,
}, {
.name = "filesystem1",
.offset = MTDPART_OFS_APPEND,
.size = SZ_512M,
.mask_flags = 0,
}, {
.name = "filesystem2",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0,
}
/* two blocks with bad block table (and mirror) at the end */
};
static struct davinci_nand_pdata davinci_nand_data = {
.mask_chipsel = BIT(14),
.parts = davinci_nand_partitions,
.nr_parts = ARRAY_SIZE(davinci_nand_partitions),
.ecc_mode = NAND_ECC_HW,
.options = NAND_USE_FLASH_BBT,
};
static struct resource davinci_nand_resources[] = {
{
.start = DM365_ASYNC_EMIF_DATA_CE0_BASE,
.end = DM365_ASYNC_EMIF_DATA_CE0_BASE + SZ_32M - 1,
.flags = IORESOURCE_MEM,
}, {
.start = DM365_ASYNC_EMIF_CONTROL_BASE,
.end = DM365_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device davinci_nand_device = {
.name = "davinci_nand",
.id = 0,
.num_resources = ARRAY_SIZE(davinci_nand_resources),
.resource = davinci_nand_resources,
.dev = {
.platform_data = &davinci_nand_data,
},
};
static struct at24_platform_data eeprom_info = {
.byte_len = (256*1024) / 8,
.page_size = 64,
@ -122,6 +199,10 @@ static void __init evm_init_i2c(void)
i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info));
}
static struct platform_device *dm365_evm_devices[] __initdata = {
&davinci_nand_device,
};
static struct davinci_uart_config uart_config __initdata = {
.enabled_uarts = (1 << 0),
};
@ -135,6 +216,9 @@ static __init void dm365_evm_init(void)
{
struct davinci_soc_info *soc_info = &davinci_soc_info;
platform_add_devices(dm365_evm_devices,
ARRAY_SIZE(dm365_evm_devices));
evm_init_i2c();
davinci_serial_init(&uart_config);