From 3d9e89bda9e9f01d55ff72f58d619e77d0c5b248 Mon Sep 17 00:00:00 2001 From: Ivan Mikhaylov Date: Wed, 28 Aug 2019 13:24:01 +0300 Subject: [PATCH] watchdog: aspeed: add support for dual boot Set WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION into WDT_CLEAR_TIMEOUT_STATUS to clear out boot code source and re-enable access to the primary SPI flash chip while booted via wdt2 from the alternate chip. AST2400 datasheet says: "In the 2nd flash booting mode, all the address mapping to CS0# would be re-directed to CS1#. And CS0# is not accessible under this mode. To access CS0#, firmware should clear the 2nd boot mode register in the WDT2 status register WDT30.bit[1]." Signed-off-by: Ivan Mikhaylov Reviewed-by: Guenter Roeck Link: https://lore.kernel.org/r/20190828102402.13155-4-i.mikhaylov@yadro.com Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/aspeed_wdt.c | 65 ++++++++++++++++++++++++++++++++++- 1 file changed, 64 insertions(+), 1 deletion(-) diff --git a/drivers/watchdog/aspeed_wdt.c b/drivers/watchdog/aspeed_wdt.c index 5b64bc2e8788..4ec0906bf12c 100644 --- a/drivers/watchdog/aspeed_wdt.c +++ b/drivers/watchdog/aspeed_wdt.c @@ -54,6 +54,8 @@ MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table); #define WDT_CTRL_ENABLE BIT(0) #define WDT_TIMEOUT_STATUS 0x10 #define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) +#define WDT_CLEAR_TIMEOUT_STATUS 0x14 +#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0) /* * WDT_RESET_WIDTH controls the characteristics of the external pulse (if @@ -166,6 +168,60 @@ static int aspeed_wdt_restart(struct watchdog_device *wdd, return 0; } +/* access_cs0 shows if cs0 is accessible, hence the reverted bit */ +static ssize_t access_cs0_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct aspeed_wdt *wdt = dev_get_drvdata(dev); + u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS); + + return sprintf(buf, "%u\n", + !(status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY)); +} + +static ssize_t access_cs0_store(struct device *dev, + struct device_attribute *attr, const char *buf, + size_t size) +{ + struct aspeed_wdt *wdt = dev_get_drvdata(dev); + unsigned long val; + + if (kstrtoul(buf, 10, &val)) + return -EINVAL; + + if (val) + writel(WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION, + wdt->base + WDT_CLEAR_TIMEOUT_STATUS); + + return size; +} + +/* + * This attribute exists only if the system has booted from the alternate + * flash with 'alt-boot' option. + * + * At alternate flash the 'access_cs0' sysfs node provides: + * ast2400: a way to get access to the primary SPI flash chip at CS0 + * after booting from the alternate chip at CS1. + * ast2500: a way to restore the normal address mapping from + * (CS0->CS1, CS1->CS0) to (CS0->CS0, CS1->CS1). + * + * Clearing the boot code selection and timeout counter also resets to the + * initial state the chip select line mapping. When the SoC is in normal + * mapping state (i.e. booted from CS0), clearing those bits does nothing for + * both versions of the SoC. For alternate boot mode (booted from CS1 due to + * wdt2 expiration) the behavior differs as described above. + * + * This option can be used with wdt2 (watchdog1) only. + */ +static DEVICE_ATTR_RW(access_cs0); + +static struct attribute *bswitch_attrs[] = { + &dev_attr_access_cs0.attr, + NULL +}; +ATTRIBUTE_GROUPS(bswitch); + static const struct watchdog_ops aspeed_wdt_ops = { .start = aspeed_wdt_start, .stop = aspeed_wdt_stop, @@ -308,9 +364,16 @@ static int aspeed_wdt_probe(struct platform_device *pdev) } status = readl(wdt->base + WDT_TIMEOUT_STATUS); - if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) + if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) { wdt->wdd.bootstatus = WDIOF_CARDRESET; + if (of_device_is_compatible(np, "aspeed,ast2400-wdt") || + of_device_is_compatible(np, "aspeed,ast2500-wdt")) + wdt->wdd.groups = bswitch_groups; + } + + dev_set_drvdata(dev, wdt); + return devm_watchdog_register_device(dev, &wdt->wdd); }