Merge remote branch 'kumar/next' into merge

arch/powerpc/boot/dts/mpc8308rdb.dts

@@ -109,7 +109,7 @@ immr@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
-		compatible = "fsl,mpc8315-immr", "simple-bus";
+		compatible = "fsl,mpc8308-immr", "simple-bus";
 		ranges = <0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;

arch/powerpc/boot/dts/p1022ds.dts

@@ -291,13 +291,13 @@ dma@c300 {
 			ranges = <0x0 0xc100 0x200>;
 			cell-index = <1>;
 			dma00: dma-channel@0 {
-				compatible = "fsl,eloplus-dma-channel";
+				compatible = "fsl,ssi-dma-channel";
 				reg = <0x0 0x80>;
 				cell-index = <0>;
 				interrupts = <76 2>;
 			};
 			dma01: dma-channel@80 {
-				compatible = "fsl,eloplus-dma-channel";
+				compatible = "fsl,ssi-dma-channel";
 				reg = <0x80 0x80>;
 				cell-index = <1>;
 				interrupts = <77 2>;

arch/powerpc/include/asm/immap_qe.h

@@ -467,13 +467,22 @@ struct qe_immap {
 extern struct qe_immap __iomem *qe_immr;
 extern phys_addr_t get_qe_base(void);
 
-static inline unsigned long immrbar_virt_to_phys(void *address)
+/*
+ * Returns the offset within the QE address space of the given pointer.
+ *
+ * Note that the QE does not support 36-bit physical addresses, so if
+ * get_qe_base() returns a number above 4GB, the caller will probably fail.
+ */
+static inline phys_addr_t immrbar_virt_to_phys(void *address)
 {
-	if ( ((u32)address >= (u32)qe_immr) &&
-			((u32)address < ((u32)qe_immr + QE_IMMAP_SIZE)) )
-		return (unsigned long)(address - (u32)qe_immr +
-				(u32)get_qe_base());
-	return (unsigned long)virt_to_phys(address);
+	void *q = (void *)qe_immr;
+
+	/* Is it a MURAM address? */
+	if ((address >= q) && (address < (q + QE_IMMAP_SIZE)))
+		return get_qe_base() + (address - q);
+
+	/* It's an address returned by kmalloc */
+	return virt_to_phys(address);
 }
 
 #endif /* __KERNEL__ */

arch/powerpc/include/asm/reg.h

@@ -283,6 +283,7 @@
 #define HID0_NOPTI	(1<<0)		/* No-op dcbt and dcbst instr. */
 
 #define SPRN_HID1	0x3F1		/* Hardware Implementation Register 1 */
+#ifdef CONFIG_6xx
 #define HID1_EMCP	(1<<31)		/* 7450 Machine Check Pin Enable */
 #define HID1_DFS	(1<<22)		/* 7447A Dynamic Frequency Scaling */
 #define HID1_PC0	(1<<16)		/* 7450 PLL_CFG[0] */
@@ -292,6 +293,7 @@
 #define HID1_SYNCBE	(1<<11)		/* 7450 ABE for sync, eieio */
 #define HID1_ABE	(1<<10)		/* 7450 Address Broadcast Enable */
 #define HID1_PS		(1<<16)		/* 750FX PLL selection */
+#endif
 #define SPRN_HID2	0x3F8		/* Hardware Implementation Register 2 */
 #define SPRN_HID2_GEKKO	0x398		/* Gekko HID2 Register */
 #define SPRN_IABR	0x3F2	/* Instruction Address Breakpoint Register */

arch/powerpc/include/asm/reg_booke.h

@@ -246,6 +246,20 @@
 					store or cache line push */
 #endif
 
+/* Bit definitions for the HID1 */
+#ifdef CONFIG_E500
+/* e500v1/v2 */
+#define HID1_PLL_CFG_MASK 0xfc000000	/* PLL_CFG input pins */
+#define HID1_RFXE	0x00020000	/* Read fault exception enable */
+#define HID1_R1DPE	0x00008000	/* R1 data bus parity enable */
+#define HID1_R2DPE	0x00004000	/* R2 data bus parity enable */
+#define HID1_ASTME	0x00002000	/* Address bus streaming mode enable */
+#define HID1_ABE	0x00001000	/* Address broadcast enable */
+#define HID1_MPXTT	0x00000400	/* MPX re-map transfer type */
+#define HID1_ATS	0x00000080	/* Atomic status */
+#define HID1_MID_MASK	0x0000000f	/* MID input pins */
+#endif
+
 /* Bit definitions for the DBSR. */
 /*
  * DBSR bits which have conflicting definitions on true Book E versus IBM 40x.

arch/powerpc/kernel/cpu_setup_fsl_booke.S

@@ -64,6 +64,12 @@ _GLOBAL(__setup_cpu_e500v2)
 	bl	__e500_icache_setup
 	bl	__e500_dcache_setup
 	bl	__setup_e500_ivors
+#ifdef CONFIG_RAPIDIO
+	/* Ensure that RFXE is set */
+	mfspr	r3,SPRN_HID1
+	oris	r3,r3,HID1_RFXE@h
+	mtspr	SPRN_HID1,r3
+#endif
 	mtlr	r4
 	blr
 _GLOBAL(__setup_cpu_e500mc)

arch/powerpc/platforms/83xx/mpc83xx.h

@@ -35,6 +35,8 @@
 
 /* system i/o configuration register high */
 #define MPC83XX_SICRH_OFFS         0x118
+#define MPC8308_SICRH_USB_MASK     0x000c0000
+#define MPC8308_SICRH_USB_ULPI     0x00040000
 #define MPC834X_SICRH_USB_UTMI     0x00020000
 #define MPC831X_SICRH_USB_MASK     0x000000e0
 #define MPC831X_SICRH_USB_ULPI     0x000000a0

arch/powerpc/platforms/83xx/usb.c

@@ -127,7 +127,8 @@ int mpc831x_usb_cfg(void)
 
 	/* Configure clock */
 	immr_node = of_get_parent(np);
-	if (immr_node && of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
+	if (immr_node && (of_device_is_compatible(immr_node, "fsl,mpc8315-immr") ||
+			of_device_is_compatible(immr_node, "fsl,mpc8308-immr")))
 		clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
 		                MPC8315_SCCR_USB_MASK,
 		                MPC8315_SCCR_USB_DRCM_01);
@@ -138,7 +139,11 @@ int mpc831x_usb_cfg(void)
 
 	/* Configure pin mux for ULPI.  There is no pin mux for UTMI */
 	if (prop && !strcmp(prop, "ulpi")) {
-		if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
+		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
+					MPC8308_SICRH_USB_MASK,
+					MPC8308_SICRH_USB_ULPI);
+		} else if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
 			clrsetbits_be32(immap + MPC83XX_SICRL_OFFS,
 					MPC8315_SICRL_USB_MASK,
 					MPC8315_SICRL_USB_ULPI);
@@ -173,6 +178,9 @@ int mpc831x_usb_cfg(void)
 		     !strcmp(prop, "utmi"))) {
 		u32 refsel;
 
+		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr"))
+			goto out;
+
 		if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
 			refsel = CONTROL_REFSEL_24MHZ;
 		else
@@ -186,9 +194,11 @@ int mpc831x_usb_cfg(void)
 		temp = CONTROL_PHY_CLK_SEL_ULPI;
 #ifdef CONFIG_USB_OTG
 		/* Set OTG_PORT */
-		dr_mode = of_get_property(np, "dr_mode", NULL);
-		if (dr_mode && !strcmp(dr_mode, "otg"))
-			temp |= CONTROL_OTG_PORT;
+		if (!of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+			dr_mode = of_get_property(np, "dr_mode", NULL);
+			if (dr_mode && !strcmp(dr_mode, "otg"))
+				temp |= CONTROL_OTG_PORT;
+		}
 #endif /* CONFIG_USB_OTG */
 		out_be32(usb_regs + FSL_USB2_CONTROL_OFFS, temp);
 	} else {
@@ -196,6 +206,7 @@ int mpc831x_usb_cfg(void)
 		ret = -EINVAL;
 	}
 
+out:
 	iounmap(usb_regs);
 	of_node_put(np);
 	return ret;

arch/powerpc/sysdev/fsl_rio.c

@@ -1555,8 +1555,6 @@ int fsl_rio_setup(struct platform_device *dev)
 	saved_mcheck_exception = ppc_md.machine_check_exception;
 	ppc_md.machine_check_exception = fsl_rio_mcheck_exception;
 #endif
-	/* Ensure that RFXE is set */
-	mtspr(SPRN_HID1, (mfspr(SPRN_HID1) | 0x20000));
 
 	return 0;
 err: