openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity

ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver. 

The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.

Raspberry Pi B+ like peripherals supported on this board include:

  - Power input through micro-USB connector (without USB OTG)
  - Native 100 Mbps ethernet using the internal PHY, as opposed to
    USB-based on the RPi
  - 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
    being connected through a USB 2.0 hub on the RPi
  - TV and audio output on a 3.5mm TRRS jack
  - HDMI output
  - Micro-SD card slot
  - Standard RPi B+ GPIO header, with the standard peripherals routed to
    the same pins.

    * 5V, 3.3V power, and ground
    * I2C0 on the H3 is routed to I2C1 pins on the RPi header
    * I2C1 on the H3 is routed to I2C0 pins on the RPi header
    * UART1 on the H3 is routed to UART0 pins on the RPi header
    * SPI0 on the H3 is routed to SPI0 pins on the RPi header,
      with GPIO pin PA17 replacing the missing Chip Select 1
    * I2S1 on the H3 is routed to PCM pins on the RPi header

  - Additional peripherals from the H3 are available on different pins.
    These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3

In addition, there are a number of new features:

  - Console UART header
  - Consumer IR receiver
  - Camera interface (not compatible with RPi)
  - Onboard microphone
  - eMMC expansion module port
  - Heatsink mounting holes
  - Power button

The power button requires corresponding software for the embedded
coprocessor to properly function.

This patch adds a dts file for this board that enables all "onboard"
peripherals currently supported. This means no display or camera
support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit is contained in:
Chen-Yu Tsai 2017-12-05 14:06:15 +08:00 committed by Maxime Ripard
parent 38ecd22004
commit 6ca358645d
2 changed files with 197 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

1
arch/arm/boot/dts/Makefile
View File

@ -953,6 +953,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
sun8i-h3-libretech-all-h3-cc.dtb \
sun8i-h3-nanopi-m1.dtb \
sun8i-h3-nanopi-m1-plus.dtb \
sun8i-h3-nanopi-neo.dtb \

196
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts Normal file
View File

@ -0,0 +1,196 @@
/*
* Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
*
* SPDX-License-Identifier: (GPL-2.0+ OR MIT)
*/
/dts-v1/;
#include "sun8i-h3.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Libre Computer Board ALL-H3-CC H3";
compatible = "libretech,all-h3-cc-h3", "allwinner,sun8i-h3";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
pwr_led {
label = "librecomputer:green:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
default-state = "on";
};
status_led {
label = "librecomputer:blue:status";
gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
};
};
gpio_keys {
compatible = "gpio-keys";
power {
label = "power";
linux,code = <KEY_POWER>;
gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
};
reg_vcc1v2: vcc1v2 {
compatible = "regulator-fixed";
regulator-name = "vcc1v2";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&reg_vcc5v0>;
gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
enable-active-high;
};
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&reg_vcc5v0>;
};
/* This represents the board's 5V input */
reg_vcc5v0: vcc5v0 {
compatible = "regulator-fixed";
regulator-name = "vcc5v0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
reg_vcc_dram: vcc-dram {
compatible = "regulator-fixed";
regulator-name = "vcc-dram";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&reg_vcc5v0>;
gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
enable-active-high;
};
reg_vcc_io: vcc-io {
compatible = "regulator-fixed";
regulator-name = "vcc-io";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&reg_vcc3v3>;
gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
};
reg_vdd_cpux: vdd-cpux {
compatible = "regulator-fixed";
regulator-name = "vdd-cpux";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&reg_vcc5v0>;
gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
enable-active-high;
};
};
&codec {
allwinner,audio-routing =
"Line Out", "LINEOUT",
"MIC1", "Mic",
"Mic", "MBIAS";
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&ehci2 {
status = "okay";
};
&ehci3 {
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "mii";
allwinner,leds-active-low;
status = "okay";
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <&reg_vcc_io>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&ohci2 {
status = "okay";
};
&ohci3 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usb_otg {
dr_mode = "host";
status = "okay";
};
&usbphy {
/* VBUS on USB ports are always on */
usb0_vbus-supply = <&reg_vcc5v0>;
usb1_vbus-supply = <&reg_vcc5v0>;
usb2_vbus-supply = <&reg_vcc5v0>;
usb3_vbus-supply = <&reg_vcc5v0>;
status = "okay";
};