diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index c14205cd6bf5..a41e0db8e71b 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -122,222 +122,6 @@ wl1835_pwrseq: wl1835-pwrseq {
 		power-off-delay-us = <10>;
 	};
 
-	soc {
-		spi0: spi@f7106000 {
-			status = "ok";
-		};
-
-		i2c0: i2c@f7100000 {
-			status = "ok";
-		};
-
-		i2c1: i2c@f7101000 {
-			status = "ok";
-		};
-
-		uart1: uart@f7111000 {
-			assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
-			assigned-clock-rates = <150000000>;
-			status = "ok";
-
-			bluetooth {
-				compatible = "ti,wl1835-st";
-				enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-				clocks = <&pmic>;
-				clock-names = "ext_clock";
-			};
-		};
-
-		uart2: uart@f7112000 {
-			status = "ok";
-		};
-
-		uart3: uart@f7113000 {
-			status = "ok";
-		};
-
-		/*
-		 * Legend: proper name = the GPIO line is used as GPIO
-		 *         NC = not connected (not routed from the SoC)
-		 *         "[PER]" = pin is muxed for peripheral (not GPIO)
-		 *         "" = no idea, schematic doesn't say, could be
-		 *              unrouted (not connected to any external pin)
-		 *         LSEC = Low Speed External Connector
-		 *         HSEC = High Speed External Connector
-		 *
-		 * Pin assignments taken from LeMaker and CircuitCo Schematics
-		 * Rev A1.
-		 *
-		 * For the lines routed to the external connectors the
-		 * lines are named after the 96Boards CE Specification 1.0,
-		 * Appendix "Expansion Connector Signal Description".
-		 *
-		 * When the 96Board naming of a line and the schematic name of
-		 * the same line are in conflict, the 96Board specification
-		 * takes precedence, which means that the external UART on the
-		 * LSEC is named UART0 while the schematic and SoC names this
-		 * UART2. This is only for the informational lines i.e. "[FOO]",
-		 * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
-		 * ones actually used for GPIO.
-		 */
-		gpio0: gpio@f8011000 {
-			gpio-line-names = "PWR_HOLD", "DSI_SEL",
-			"USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
-			"PWRON_DET", "5V_HUB_EN";
-		};
-
-		gpio1: gpio@f8012000 {
-			gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
-			"WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
-		};
-
-		gpio2: gpio@f8013000 {
-			gpio-line-names =
-				"GPIO-A", /* LSEC Pin 23: GPIO2_0 */
-				"GPIO-B", /* LSEC Pin 24: GPIO2_1 */
-				"GPIO-C", /* LSEC Pin 25: GPIO2_2 */
-				"GPIO-D", /* LSEC Pin 26: GPIO2_3 */
-				"GPIO-E", /* LSEC Pin 27: GPIO2_4 */
-				"USB_ID_DET", "USB_VBUS_DET",
-				"GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
-		};
-
-		gpio3: gpio@f8014000 {
-			gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
-			"WLAN_ACTIVE", "NC", "NC";
-		};
-
-		gpio4: gpio@f7020000 {
-			gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
-			"USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
-		};
-
-		gpio5: gpio@f7021000 {
-			gpio-line-names = "NC", "NC",
-			"[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
-			"[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
-			"[AUX_SSI1]", "NC",
-			"[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
-			"[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
-		};
-
-		gpio6: gpio@f7022000 {
-			gpio-line-names =
-			"[SPI0_DIN]", /* Pin 10: SPI0_DI */
-			"[SPI0_DOUT]", /* Pin 14: SPI0_DO */
-			"[SPI0_CS]", /* Pin 12: SPI0_CS_N */
-			"[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
-			"NC", "NC", "NC",
-			"GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
-		};
-
-		gpio7: gpio@f7023000 {
-			gpio-line-names = "NC", "NC", "NC", "NC",
-			"[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
-			"[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
-			"NC", "NC";
-		};
-
-		gpio8: gpio@f7024000 {
-			gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
-			"", "", "", "", "", "";
-		};
-
-		gpio9: gpio@f7025000 {
-			gpio-line-names = "",
-			"GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
-			"GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
-			"NC", "NC", "NC", "NC", "[ISP_CCLK0]";
-		};
-
-		gpio10: gpio@f7026000 {
-			gpio-line-names = "BOOT_SEL",
-			"[ISP_CCLK1]",
-			"GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
-			"GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
-			"NC", "NC",
-			"[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
-			"[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
-		};
-
-		gpio11: gpio@f7027000 {
-			gpio-line-names =
-			"[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
-			"[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
-			"", "NC", "NC", "NC", "", "";
-		};
-
-		gpio12: gpio@f7028000 {
-			gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
-			"[BT_PCM_DO]",
-			"NC", "NC", "NC", "NC",
-			"GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
-		};
-
-		gpio13: gpio@f7029000 {
-			gpio-line-names = "[UART0_RX]", "[UART0_TX]",
-			"[BT_UART1_CTS]", "[BT_UART1_RTS]",
-			"[BT_UART1_RX]", "[BT_UART1_TX]",
-			"[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
-			"[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
-		};
-
-		gpio14: gpio@f702a000 {
-			gpio-line-names =
-			"[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
-			"[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
-			"[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
-			"[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
-			"[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
-			"[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
-			"[I2C2_SCL]", "[I2C2_SDA]";
-		};
-
-		gpio15: gpio@f702b000 {
-			gpio-line-names = "", "", "", "", "", "", "NC", "";
-		};
-
-		/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
-
-		dwmmc_0: dwmmc0@f723d000 {
-			cap-mmc-highspeed;
-			non-removable;
-			bus-width = <0x8>;
-			vmmc-supply = <&ldo19>;
-		};
-
-		dwmmc_1: dwmmc1@f723e000 {
-			card-detect-delay = <200>;
-			cap-sd-highspeed;
-			sd-uhs-sdr12;
-			sd-uhs-sdr25;
-			sd-uhs-sdr50;
-			vqmmc-supply = <&ldo7>;
-			vmmc-supply = <&ldo10>;
-			bus-width = <0x4>;
-			disable-wp;
-			cd-gpios = <&gpio1 0 1>;
-		};
-
-		dwmmc_2: dwmmc2@f723f000 {
-			bus-width = <0x4>;
-			non-removable;
-			cap-power-off-card;
-			vmmc-supply = <&reg_vdd_3v3>;
-			mmc-pwrseq = <&wl1835_pwrseq>;
-
-			#address-cells = <0x1>;
-			#size-cells = <0x0>;
-			wlcore: wlcore@2 {
-				compatible = "ti,wl1835";
-				reg = <2>;	/* sdio func num */
-				/* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
-				interrupt-parent = <&gpio1>;
-				interrupts = <3 IRQ_TYPE_EDGE_RISING>;
-			};
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -480,10 +264,26 @@ sound_card {
 	};
 };
 
+&uart1 {
+	assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
+	assigned-clock-rates = <150000000>;
+	status = "ok";
+
+	bluetooth {
+		compatible = "ti,wl1835-st";
+		enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		clocks = <&pmic>;
+		clock-names = "ext_clock";
+	};
+};
+
 &uart2 {
+	status = "ok";
 	label = "LS-UART0";
 };
+
 &uart3 {
+	status = "ok";
 	label = "LS-UART1";
 };
 
@@ -506,6 +306,196 @@ dsi_out0: endpoint@0 {
 	};
 };
 
+&dwmmc_0 {
+	cap-mmc-highspeed;
+	non-removable;
+	bus-width = <0x8>;
+	vmmc-supply = <&ldo19>;
+};
+
+&dwmmc_1 {
+	card-detect-delay = <200>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	vqmmc-supply = <&ldo7>;
+	vmmc-supply = <&ldo10>;
+	bus-width = <0x4>;
+	disable-wp;
+	cd-gpios = <&gpio1 0 1>;
+};
+
+&dwmmc_2 {
+	bus-width = <0x4>;
+	non-removable;
+	cap-power-off-card;
+	vmmc-supply = <&reg_vdd_3v3>;
+	mmc-pwrseq = <&wl1835_pwrseq>;
+
+	#address-cells = <0x1>;
+	#size-cells = <0x0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;	/* sdio func num */
+		/* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+/*
+ * Legend: proper name = the GPIO line is used as GPIO
+ *         NC = not connected (not routed from the SoC)
+ *         "[PER]" = pin is muxed for peripheral (not GPIO)
+ *         "" = no idea, schematic doesn't say, could be
+ *              unrouted (not connected to any external pin)
+ *         LSEC = Low Speed External Connector
+ *         HSEC = High Speed External Connector
+ *
+ * Pin assignments taken from LeMaker and CircuitCo Schematics
+ * Rev A1.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART2. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+&gpio0 {
+	gpio-line-names = "PWR_HOLD", "DSI_SEL",
+	"USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
+	"PWRON_DET", "5V_HUB_EN";
+};
+
+&gpio1 {
+	gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
+	"WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPIO-A", /* LSEC Pin 23: GPIO2_0 */
+		"GPIO-B", /* LSEC Pin 24: GPIO2_1 */
+		"GPIO-C", /* LSEC Pin 25: GPIO2_2 */
+		"GPIO-D", /* LSEC Pin 26: GPIO2_3 */
+		"GPIO-E", /* LSEC Pin 27: GPIO2_4 */
+		"USB_ID_DET", "USB_VBUS_DET",
+		"GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
+};
+
+&gpio3 {
+	gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
+	"WLAN_ACTIVE", "NC", "NC";
+};
+
+&gpio4 {
+	gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
+	"USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
+};
+
+&gpio5 {
+	gpio-line-names = "NC", "NC",
+	"[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
+	"[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
+	"[AUX_SSI1]", "NC",
+	"[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
+	"[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
+};
+
+&gpio6 {
+	gpio-line-names =
+	"[SPI0_DIN]", /* Pin 10: SPI0_DI */
+	"[SPI0_DOUT]", /* Pin 14: SPI0_DO */
+	"[SPI0_CS]", /* Pin 12: SPI0_CS_N */
+	"[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
+	"NC", "NC", "NC",
+	"GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
+};
+
+&gpio7 {
+	gpio-line-names = "NC", "NC", "NC", "NC",
+	"[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
+	"[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
+	"NC", "NC";
+};
+
+&gpio8 {
+	gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
+	"", "", "", "", "", "";
+};
+
+&gpio9 {
+	gpio-line-names = "",
+	"GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
+	"GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
+	"NC", "NC", "NC", "NC", "[ISP_CCLK0]";
+};
+
+&gpio10 {
+	gpio-line-names = "BOOT_SEL",
+	"[ISP_CCLK1]",
+	"GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
+	"GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
+	"NC", "NC",
+	"[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
+	"[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
+};
+
+&gpio11 {
+	gpio-line-names =
+	"[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
+	"[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
+	"", "NC", "NC", "NC", "", "";
+};
+
+&gpio12 {
+	gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
+	"[BT_PCM_DO]",
+	"NC", "NC", "NC", "NC",
+	"GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
+};
+
+&gpio13 {
+	gpio-line-names = "[UART0_RX]", "[UART0_TX]",
+	"[BT_UART1_CTS]", "[BT_UART1_RTS]",
+	"[BT_UART1_RX]", "[BT_UART1_TX]",
+	"[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
+	"[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
+};
+
+&gpio14 {
+	gpio-line-names =
+	"[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
+	"[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
+	"[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
+	"[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
+	"[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
+	"[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
+	"[I2C2_SCL]", "[I2C2_SDA]";
+};
+
+&gpio15 {
+	gpio-line-names = "", "", "", "", "", "", "NC", "";
+};
+
+/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
+
+
+&i2c0 {
+	status = "ok";
+};
+
+&i2c1 {
+	status = "ok";
+};
+
 &i2c2 {
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -549,3 +539,7 @@ i2s0_cpu_endpoint: endpoint {
 		};
 	};
 };
+
+&spi0 {
+	status = "ok";
+};