mirror of https://gitee.com/openkylin/linux.git
net: stmmac: use GPIO descriptors in stmmac_mdio_reset
Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the "snps,reset-gpio" for GPIO descriptors so we don't need to take care of it inside the driver anymore. The advantage of this is that we now preserve the GPIO flags which are passed via devicetree. This is required on some newer Amlogic boards which use an Open Drain pin for the reset GPIO. This pin can only output a LOW signal or switch to input mode but it cannot output a HIGH signal. There are already devicetree bindings for these special cases and GPIO core already takes care of them but only if we use GPIO descriptors instead of GPIO numbers. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
parent
4373a5e260
commit
7c86f20d15
|
@ -20,11 +20,11 @@
|
|||
Maintainer: Giuseppe Cavallaro <peppe.cavallaro@st.com>
|
||||
*******************************************************************************/
|
||||
|
||||
#include <linux/gpio/consumer.h>
|
||||
#include <linux/io.h>
|
||||
#include <linux/iopoll.h>
|
||||
#include <linux/mii.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_gpio.h>
|
||||
#include <linux/of_mdio.h>
|
||||
#include <linux/phy.h>
|
||||
#include <linux/slab.h>
|
||||
|
@ -251,37 +251,36 @@ int stmmac_mdio_reset(struct mii_bus *bus)
|
|||
|
||||
#ifdef CONFIG_OF
|
||||
if (priv->device->of_node) {
|
||||
struct gpio_desc *reset_gpio;
|
||||
|
||||
if (data->reset_gpio < 0) {
|
||||
struct device_node *np = priv->device->of_node;
|
||||
|
||||
if (!np)
|
||||
return 0;
|
||||
|
||||
data->reset_gpio = of_get_named_gpio(np,
|
||||
"snps,reset-gpio", 0);
|
||||
if (data->reset_gpio < 0)
|
||||
return 0;
|
||||
reset_gpio = devm_gpiod_get_optional(priv->device,
|
||||
"snps,reset",
|
||||
GPIOD_OUT_LOW);
|
||||
if (IS_ERR(reset_gpio))
|
||||
return PTR_ERR(reset_gpio);
|
||||
|
||||
data->active_low = of_property_read_bool(np,
|
||||
"snps,reset-active-low");
|
||||
of_property_read_u32_array(np,
|
||||
"snps,reset-delays-us", data->delays, 3);
|
||||
} else {
|
||||
reset_gpio = gpio_to_desc(data->reset_gpio);
|
||||
|
||||
if (devm_gpio_request(priv->device, data->reset_gpio,
|
||||
"mdio-reset"))
|
||||
return 0;
|
||||
gpiod_direction_output(reset_gpio, 0);
|
||||
}
|
||||
|
||||
gpio_direction_output(data->reset_gpio,
|
||||
data->active_low ? 1 : 0);
|
||||
if (data->delays[0])
|
||||
msleep(DIV_ROUND_UP(data->delays[0], 1000));
|
||||
|
||||
gpio_set_value(data->reset_gpio, data->active_low ? 0 : 1);
|
||||
gpiod_set_value_cansleep(reset_gpio, 1);
|
||||
if (data->delays[1])
|
||||
msleep(DIV_ROUND_UP(data->delays[1], 1000));
|
||||
|
||||
gpio_set_value(data->reset_gpio, data->active_low ? 1 : 0);
|
||||
gpiod_set_value_cansleep(reset_gpio, 0);
|
||||
if (data->delays[2])
|
||||
msleep(DIV_ROUND_UP(data->delays[2], 1000));
|
||||
}
|
||||
|
|
|
@ -97,7 +97,7 @@ struct stmmac_mdio_bus_data {
|
|||
int *irqs;
|
||||
int probed_phy_irq;
|
||||
#ifdef CONFIG_OF
|
||||
int reset_gpio, active_low;
|
||||
int reset_gpio;
|
||||
u32 delays[3];
|
||||
#endif
|
||||
};
|
||||
|
|
Loading…
Reference in New Issue