mirror of https://gitee.com/openkylin/linux.git
Input: ALPS - add documentation for protocol versions 3 and 4
Also converts from using "old" and "new" to describe the already-known protocols to using "version 1" and "version 2" to match the code. Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Chase Douglas <chase.douglas@canonical.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This commit is contained in:
Seth Forshee
Dmitry Torokhov
parent
01ce661fc8
commit
7cf801cfc0
|
|
@ -4,12 +4,9 @@ ALPS Touchpad Protocol
|
|||
Introduction
|
||||
------------
|
||||
|
||||
Currently the ALPS touchpad driver supports two protocol versions in use by
|
||||
ALPS touchpads, the "old" and "new" protocol versions. Fundamentally these
|
||||
differ only in the format of their event packets (in reality many features may
|
||||
be found on new protocol devices that aren't found on the old protocol
|
||||
devices, but these are handled transparently as feature differences rather
|
||||
than protocol differences).
|
||||
Currently the ALPS touchpad driver supports four protocol versions in use by
|
||||
ALPS touchpads, called versions 1, 2, 3, and 4. Information about the various
|
||||
protocol versions is contained in the following sections.
|
||||
|
||||
Detection
|
||||
---------
|
||||
|
|
@ -22,10 +19,37 @@ If the E6 report is successful, the touchpad model is identified using the "E7
|
|||
report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is
|
||||
matched against known models in the alps_model_data_array.
|
||||
|
||||
With protocol versions 3 and 4, the E7 report model signature is always
|
||||
73-02-64. To differentiate between these versions, the response from the
|
||||
"Enter Command Mode" sequence must be inspected as described below.
|
||||
|
||||
Command Mode
|
||||
------------
|
||||
|
||||
Protocol versions 3 and 4 have a command mode that is used to read and write
|
||||
one-byte device registers in a 16-bit address space. The command sequence
|
||||
EC-EC-EC-E9 places the device in command mode, and the device will respond
|
||||
with 88-07 followed by a third byte. This third byte can be used to determine
|
||||
whether the devices uses the version 3 or 4 protocol.
|
||||
|
||||
To exit command mode, PSMOUSE_CMD_SETSTREAM (EA) is sent to the touchpad.
|
||||
|
||||
While in command mode, register addresses can be set by first sending a
|
||||
specific command, either EC for v3 devices or F5 for v4 devices. Then the
|
||||
address is sent one nibble at a time, where each nibble is encoded as a
|
||||
command with optional data. This enoding differs slightly between the v3 and
|
||||
v4 protocols.
|
||||
|
||||
Once an address has been set, the addressed register can be read by sending
|
||||
PSMOUSE_CMD_GETINFO (E9). The first two bytes of the response contains the
|
||||
address of the register being read, and the third contains the value of the
|
||||
register. Registers are written by writing the value one nibble at a time
|
||||
using the same encoding used for addresses.
|
||||
|
||||
Packet Format
|
||||
-------------
|
||||
|
||||
In the following tables, the following notation us used.
|
||||
In the following tables, the following notation is used.
|
||||
|
||||
CAPITALS = stick, miniscules = touchpad
|
||||
|
||||
|
|
@ -41,8 +65,8 @@ PS/2 packet format
|
|||
|
||||
Note that the device never signals overflow condition.
|
||||
|
||||
ALPS Absolute Mode - Old Format
|
||||
-------------------------------
|
||||
ALPS Absolute Mode - Protocol Verion 1
|
||||
--------------------------------------
|
||||
|
||||
byte 0: 1 0 0 0 1 x9 x8 x7
|
||||
byte 1: 0 x6 x5 x4 x3 x2 x1 x0
|
||||
|
|
@ -51,8 +75,8 @@ ALPS Absolute Mode - Old Format
|
|||
byte 4: 0 y6 y5 y4 y3 y2 y1 y0
|
||||
byte 5: 0 z6 z5 z4 z3 z2 z1 z0
|
||||
|
||||
ALPS Absolute Mode - New Format
|
||||
-------------------------------
|
||||
ALPS Absolute Mode - Protocol Version 2
|
||||
---------------------------------------
|
||||
|
||||
byte 0: 1 ? ? ? 1 ? ? ?
|
||||
byte 1: 0 x6 x5 x4 x3 x2 x1 x0
|
||||
|
|
@ -73,3 +97,92 @@ Dualpoint device -- interleaved packet format
|
|||
byte 6: 0 y9 y8 y7 1 m r l
|
||||
byte 7: 0 y6 y5 y4 y3 y2 y1 y0
|
||||
byte 8: 0 z6 z5 z4 z3 z2 z1 z0
|
||||
|
||||
ALPS Absolute Mode - Protocol Version 3
|
||||
---------------------------------------
|
||||
|
||||
ALPS protocol version 3 has three different packet formats. The first two are
|
||||
associated with touchpad events, and the third is associatd with trackstick
|
||||
events.
|
||||
|
||||
The first type is the touchpad position packet.
|
||||
|
||||
byte 0: 1 ? x1 x0 1 1 1 1
|
||||
byte 1: 0 x10 x9 x8 x7 x6 x5 x4
|
||||
byte 2: 0 y10 y9 y8 y7 y6 y5 y4
|
||||
byte 3: 0 M R L 1 m r l
|
||||
byte 4: 0 mt x3 x2 y3 y2 y1 y0
|
||||
byte 5: 0 z6 z5 z4 z3 z2 z1 z0
|
||||
|
||||
Note that for some devices the trackstick buttons are reported in this packet,
|
||||
and on others it is reported in the trackstick packets.
|
||||
|
||||
The second packet type contains bitmaps representing the x and y axes. In the
|
||||
bitmaps a given bit is set if there is a finger covering that position on the
|
||||
given axis. Thus the bitmap packet can be used for low-resolution multi-touch
|
||||
data, although finger tracking is not possible. This packet also encodes the
|
||||
number of contacts (f1 and f0 in the table below).
|
||||
|
||||
byte 0: 1 1 x1 x0 1 1 1 1
|
||||
byte 1: 0 x8 x7 x6 x5 x4 x3 x2
|
||||
byte 2: 0 y7 y6 y5 y4 y3 y2 y1
|
||||
byte 3: 0 y10 y9 y8 1 1 1 1
|
||||
byte 4: 0 x14 x13 x12 x11 x10 x9 y0
|
||||
byte 5: 0 1 ? ? ? ? f1 f0
|
||||
|
||||
This packet only appears after a position packet with the mt bit set, and
|
||||
ususally only appears when there are two or more contacts (although
|
||||
ocassionally it's seen with only a single contact).
|
||||
|
||||
The final v3 packet type is the trackstick packet.
|
||||
|
||||
byte 0: 1 1 x7 y7 1 1 1 1
|
||||
byte 1: 0 x6 x5 x4 x3 x2 x1 x0
|
||||
byte 2: 0 y6 y5 y4 y3 y2 y1 y0
|
||||
byte 3: 0 1 0 0 1 0 0 0
|
||||
byte 4: 0 z4 z3 z2 z1 z0 ? ?
|
||||
byte 5: 0 0 1 1 1 1 1 1
|
||||
|
||||
ALPS Absolute Mode - Protocol Version 4
|
||||
---------------------------------------
|
||||
|
||||
Protocol version 4 has an 8-byte packet format.
|
||||
|
||||
byte 0: 1 ? x1 x0 1 1 1 1
|
||||
byte 1: 0 x10 x9 x8 x7 x6 x5 x4
|
||||
byte 2: 0 y10 y9 y8 y7 y6 y5 y4
|
||||
byte 3: 0 1 x3 x2 y3 y2 y1 y0
|
||||
byte 4: 0 ? ? ? 1 ? r l
|
||||
byte 5: 0 z6 z5 z4 z3 z2 z1 z0
|
||||
byte 6: bitmap data (described below)
|
||||
byte 7: bitmap data (described below)
|
||||
|
||||
The last two bytes represent a partial bitmap packet, with 3 full packets
|
||||
required to construct a complete bitmap packet. Once assembled, the 6-byte
|
||||
bitmap packet has the following format:
|
||||
|
||||
byte 0: 0 1 x7 x6 x5 x4 x3 x2
|
||||
byte 1: 0 x1 x0 y4 y3 y2 y1 y0
|
||||
byte 2: 0 0 ? x14 x13 x12 x11 x10
|
||||
byte 3: 0 x9 x8 y9 y8 y7 y6 y5
|
||||
byte 4: 0 0 0 0 0 0 0 0
|
||||
byte 5: 0 0 0 0 0 0 0 y10
|
||||
|
||||
There are several things worth noting here.
|
||||
|
||||
1) In the bitmap data, bit 6 of byte 0 serves as a sync byte to
|
||||
identify the first fragment of a bitmap packet.
|
||||
|
||||
2) The bitmaps represent the same data as in the v3 bitmap packets, although
|
||||
the packet layout is different.
|
||||
|
||||
3) There doesn't seem to be a count of the contact points anywhere in the v4
|
||||
protocol packets. Deriving a count of contact points must be done by
|
||||
analyzing the bitmaps.
|
||||
|
||||
4) There is a 3 to 1 ratio of position packets to bitmap packets. Therefore
|
||||
MT position can only be updated for every third ST position update, and
|
||||
the count of contact points can only be updated every third packet as
|
||||
well.
|
||||
|
||||
So far no v4 devices with tracksticks have been encountered.
|
||||
|
|
|
|||
Loading…
Reference in New Issue