mirror of https://gitee.com/openkylin/linux.git
[ARM] 4874/2: ixp4xx: Add support for the Freecom FSG-3 board
The Freecom-FSG3 is a small network-attached-storage device with the following feature set: * Intel IXP422 * 4MB Flash (ixp4xx flash driver) * 64MB RAM * 4 USB 2.0 host ports (ehci and ohci drivers) * 1 WAN (eth1) and 3 LAN (eth0) ethernet ports * Supported by the open source ixp4xx ethernet driver * Via VT6421 disk controller (libata and sata-via drivers) * Internal hard disk (PATA supported, SATA not yet supported) * External SATA port (not yet supported) * ISL1208 RTC chip * Winbond 83782 temp sensor and fan controller * MiniPCI slot The ixp4xx_defconfig is also updated to support this device (the leds-fsg driver is to be submitted separately via the leds tree after this initial support is merged, as it depends on header gpio defines). Signed-off-by: Rod Whitby <rod@whitby.id.au> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit is contained in:
Rod Whitby
Russell King
parent
05dda977f2
commit
7e36e2f535
|
|
@ -165,6 +165,7 @@ CONFIG_ARCH_PRPMC1100=y
|
|||
CONFIG_MACH_NAS100D=y
|
||||
CONFIG_MACH_DSMG600=y
|
||||
CONFIG_ARCH_IXDP4XX=y
|
||||
CONFIG_MACH_FSG=y
|
||||
CONFIG_CPU_IXP46X=y
|
||||
CONFIG_CPU_IXP43X=y
|
||||
CONFIG_MACH_GTWX5715=y
|
||||
|
|
@ -770,7 +771,7 @@ CONFIG_ATA=y
|
|||
# CONFIG_SATA_SIL24 is not set
|
||||
# CONFIG_SATA_SIS is not set
|
||||
# CONFIG_SATA_ULI is not set
|
||||
# CONFIG_SATA_VIA is not set
|
||||
CONFIG_SATA_VIA=y
|
||||
# CONFIG_SATA_VITESSE is not set
|
||||
# CONFIG_SATA_INIC162X is not set
|
||||
# CONFIG_PATA_ALI is not set
|
||||
|
|
@ -1143,7 +1144,7 @@ CONFIG_HWMON=y
|
|||
# CONFIG_SENSORS_VIA686A is not set
|
||||
# CONFIG_SENSORS_VT1211 is not set
|
||||
# CONFIG_SENSORS_VT8231 is not set
|
||||
# CONFIG_SENSORS_W83781D is not set
|
||||
CONFIG_SENSORS_W83781D=y
|
||||
# CONFIG_SENSORS_W83791D is not set
|
||||
# CONFIG_SENSORS_W83792D is not set
|
||||
# CONFIG_SENSORS_W83793 is not set
|
||||
|
|
@ -1334,8 +1335,8 @@ CONFIG_LEDS_CLASS=y
|
|||
#
|
||||
# LED drivers
|
||||
#
|
||||
# CONFIG_LEDS_IXP4XX is not set
|
||||
CONFIG_LEDS_GPIO=y
|
||||
CONFIG_LEDS_FSG=y
|
||||
|
||||
#
|
||||
# LED Triggers
|
||||
|
|
@ -1367,7 +1368,7 @@ CONFIG_RTC_INTF_DEV=y
|
|||
# CONFIG_RTC_DRV_DS1672 is not set
|
||||
# CONFIG_RTC_DRV_MAX6900 is not set
|
||||
# CONFIG_RTC_DRV_RS5C372 is not set
|
||||
# CONFIG_RTC_DRV_ISL1208 is not set
|
||||
CONFIG_RTC_DRV_ISL1208=y
|
||||
CONFIG_RTC_DRV_X1205=y
|
||||
CONFIG_RTC_DRV_PCF8563=y
|
||||
# CONFIG_RTC_DRV_PCF8583 is not set
|
||||
|
|
|
|||
|
|
@ -125,6 +125,15 @@ config ARCH_IXDP4XX
|
|||
depends on ARCH_IXDP425 || MACH_IXDP465 || MACH_KIXRP435
|
||||
default y
|
||||
|
||||
config MACH_FSG
|
||||
bool
|
||||
prompt "Freecom FSG-3"
|
||||
select PCI
|
||||
help
|
||||
Say 'Y' here if you want your kernel to support Freecom's
|
||||
FSG-3 device. For more information on this platform,
|
||||
see http://www.nslu2-linux.org/wiki/FSG3/HomePage
|
||||
|
||||
#
|
||||
# Certain registers and IRQs are only enabled if supporting IXP465 CPUs
|
||||
#
|
||||
|
|
|
|||
|
|
@ -15,6 +15,7 @@ obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o
|
|||
obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o
|
||||
obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
|
||||
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
|
||||
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
|
||||
|
||||
obj-y += common.o
|
||||
|
||||
|
|
@ -28,6 +29,7 @@ obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o
|
|||
obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o
|
||||
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
|
||||
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
|
||||
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
|
||||
|
||||
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
|
||||
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,71 @@
|
|||
/*
|
||||
* arch/arch/mach-ixp4xx/fsg-pci.c
|
||||
*
|
||||
* FSG board-level PCI initialization
|
||||
*
|
||||
* Author: Rod Whitby <rod@whitby.id.au>
|
||||
* Maintainer: http://www.nslu2-linux.org/
|
||||
*
|
||||
* based on ixdp425-pci.c:
|
||||
* Copyright (C) 2002 Intel Corporation.
|
||||
* Copyright (C) 2003-2004 MontaVista Software, Inc.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*
|
||||
*/
|
||||
|
||||
#include <linux/pci.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/irq.h>
|
||||
|
||||
#include <asm/mach/pci.h>
|
||||
#include <asm/mach-types.h>
|
||||
|
||||
void __init fsg_pci_preinit(void)
|
||||
{
|
||||
set_irq_type(IRQ_FSG_PCI_INTA, IRQT_LOW);
|
||||
set_irq_type(IRQ_FSG_PCI_INTB, IRQT_LOW);
|
||||
set_irq_type(IRQ_FSG_PCI_INTC, IRQT_LOW);
|
||||
|
||||
ixp4xx_pci_preinit();
|
||||
}
|
||||
|
||||
static int __init fsg_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
|
||||
{
|
||||
static int pci_irq_table[FSG_PCI_IRQ_LINES] = {
|
||||
IRQ_FSG_PCI_INTC,
|
||||
IRQ_FSG_PCI_INTB,
|
||||
IRQ_FSG_PCI_INTA,
|
||||
};
|
||||
|
||||
int irq = -1;
|
||||
slot = slot - 11;
|
||||
|
||||
if (slot >= 1 && slot <= FSG_PCI_MAX_DEV &&
|
||||
pin >= 1 && pin <= FSG_PCI_IRQ_LINES)
|
||||
irq = pci_irq_table[(slot - 1)];
|
||||
printk(KERN_INFO "%s: Mapped slot %d pin %d to IRQ %d\n",
|
||||
__func__, slot, pin, irq);
|
||||
|
||||
return irq;
|
||||
}
|
||||
|
||||
struct hw_pci fsg_pci __initdata = {
|
||||
.nr_controllers = 1,
|
||||
.preinit = fsg_pci_preinit,
|
||||
.swizzle = pci_std_swizzle,
|
||||
.setup = ixp4xx_setup,
|
||||
.scan = ixp4xx_scan_bus,
|
||||
.map_irq = fsg_map_irq,
|
||||
};
|
||||
|
||||
int __init fsg_pci_init(void)
|
||||
{
|
||||
if (machine_is_fsg())
|
||||
pci_common_init(&fsg_pci);
|
||||
return 0;
|
||||
}
|
||||
|
||||
subsys_initcall(fsg_pci_init);
|
||||
|
|
@ -0,0 +1,276 @@
|
|||
/*
|
||||
* arch/arm/mach-ixp4xx/fsg-setup.c
|
||||
*
|
||||
* FSG board-setup
|
||||
*
|
||||
* Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
|
||||
*
|
||||
* based on ixdp425-setup.c:
|
||||
* Copyright (C) 2003-2004 MontaVista Software, Inc.
|
||||
* based on nslu2-power.c
|
||||
* Copyright (C) 2005 Tower Technologies
|
||||
*
|
||||
* Author: Rod Whitby <rod@whitby.id.au>
|
||||
* Maintainers: http://www.nslu2-linux.org/
|
||||
*
|
||||
*/
|
||||
|
||||
#include <linux/if_ether.h>
|
||||
#include <linux/irq.h>
|
||||
#include <linux/serial.h>
|
||||
#include <linux/serial_8250.h>
|
||||
#include <linux/leds.h>
|
||||
#include <linux/reboot.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/i2c-gpio.h>
|
||||
|
||||
#include <asm/mach-types.h>
|
||||
#include <asm/mach/arch.h>
|
||||
#include <asm/mach/flash.h>
|
||||
#include <asm/io.h>
|
||||
#include <asm/gpio.h>
|
||||
|
||||
static struct flash_platform_data fsg_flash_data = {
|
||||
.map_name = "cfi_probe",
|
||||
.width = 2,
|
||||
};
|
||||
|
||||
static struct resource fsg_flash_resource = {
|
||||
.flags = IORESOURCE_MEM,
|
||||
};
|
||||
|
||||
static struct platform_device fsg_flash = {
|
||||
.name = "IXP4XX-Flash",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &fsg_flash_data,
|
||||
},
|
||||
.num_resources = 1,
|
||||
.resource = &fsg_flash_resource,
|
||||
};
|
||||
|
||||
static struct i2c_gpio_platform_data fsg_i2c_gpio_data = {
|
||||
.sda_pin = FSG_SDA_PIN,
|
||||
.scl_pin = FSG_SCL_PIN,
|
||||
};
|
||||
|
||||
static struct platform_device fsg_i2c_gpio = {
|
||||
.name = "i2c-gpio",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &fsg_i2c_gpio_data,
|
||||
},
|
||||
};
|
||||
|
||||
static struct i2c_board_info __initdata fsg_i2c_board_info [] = {
|
||||
{
|
||||
I2C_BOARD_INFO("rtc-isl1208", 0x6f),
|
||||
},
|
||||
};
|
||||
|
||||
static struct resource fsg_uart_resources[] = {
|
||||
{
|
||||
.start = IXP4XX_UART1_BASE_PHYS,
|
||||
.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
{
|
||||
.start = IXP4XX_UART2_BASE_PHYS,
|
||||
.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
|
||||
.flags = IORESOURCE_MEM,
|
||||
}
|
||||
};
|
||||
|
||||
static struct plat_serial8250_port fsg_uart_data[] = {
|
||||
{
|
||||
.mapbase = IXP4XX_UART1_BASE_PHYS,
|
||||
.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
|
||||
.irq = IRQ_IXP4XX_UART1,
|
||||
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
|
||||
.iotype = UPIO_MEM,
|
||||
.regshift = 2,
|
||||
.uartclk = IXP4XX_UART_XTAL,
|
||||
},
|
||||
{
|
||||
.mapbase = IXP4XX_UART2_BASE_PHYS,
|
||||
.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
|
||||
.irq = IRQ_IXP4XX_UART2,
|
||||
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
|
||||
.iotype = UPIO_MEM,
|
||||
.regshift = 2,
|
||||
.uartclk = IXP4XX_UART_XTAL,
|
||||
},
|
||||
{ }
|
||||
};
|
||||
|
||||
static struct platform_device fsg_uart = {
|
||||
.name = "serial8250",
|
||||
.id = PLAT8250_DEV_PLATFORM,
|
||||
.dev = {
|
||||
.platform_data = fsg_uart_data,
|
||||
},
|
||||
.num_resources = ARRAY_SIZE(fsg_uart_resources),
|
||||
.resource = fsg_uart_resources,
|
||||
};
|
||||
|
||||
static struct platform_device fsg_leds = {
|
||||
.name = "fsg-led",
|
||||
.id = -1,
|
||||
};
|
||||
|
||||
/* Built-in 10/100 Ethernet MAC interfaces */
|
||||
static struct eth_plat_info fsg_plat_eth[] = {
|
||||
{
|
||||
.phy = 5,
|
||||
.rxq = 3,
|
||||
.txreadyq = 20,
|
||||
}, {
|
||||
.phy = 4,
|
||||
.rxq = 4,
|
||||
.txreadyq = 21,
|
||||
}
|
||||
};
|
||||
|
||||
static struct platform_device fsg_eth[] = {
|
||||
{
|
||||
.name = "ixp4xx_eth",
|
||||
.id = IXP4XX_ETH_NPEB,
|
||||
.dev = {
|
||||
.platform_data = fsg_plat_eth,
|
||||
},
|
||||
}, {
|
||||
.name = "ixp4xx_eth",
|
||||
.id = IXP4XX_ETH_NPEC,
|
||||
.dev = {
|
||||
.platform_data = fsg_plat_eth + 1,
|
||||
},
|
||||
}
|
||||
};
|
||||
|
||||
static struct platform_device *fsg_devices[] __initdata = {
|
||||
&fsg_i2c_gpio,
|
||||
&fsg_flash,
|
||||
&fsg_leds,
|
||||
&fsg_eth[0],
|
||||
&fsg_eth[1],
|
||||
};
|
||||
|
||||
static irqreturn_t fsg_power_handler(int irq, void *dev_id)
|
||||
{
|
||||
/* Signal init to do the ctrlaltdel action, this will bypass init if
|
||||
* it hasn't started and do a kernel_restart.
|
||||
*/
|
||||
ctrl_alt_del();
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static irqreturn_t fsg_reset_handler(int irq, void *dev_id)
|
||||
{
|
||||
/* This is the paper-clip reset which does an emergency reboot. */
|
||||
printk(KERN_INFO "Restarting system.\n");
|
||||
machine_restart(NULL);
|
||||
|
||||
/* This should never be reached. */
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static void __init fsg_init(void)
|
||||
{
|
||||
DECLARE_MAC_BUF(mac_buf);
|
||||
uint8_t __iomem *f;
|
||||
int i;
|
||||
|
||||
ixp4xx_sys_init();
|
||||
|
||||
fsg_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
|
||||
fsg_flash_resource.end =
|
||||
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
|
||||
|
||||
*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
|
||||
*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
|
||||
|
||||
/* Configure CS2 for operation, 8bit and writable */
|
||||
*IXP4XX_EXP_CS2 = 0xbfff0002;
|
||||
|
||||
i2c_register_board_info(0, fsg_i2c_board_info,
|
||||
ARRAY_SIZE(fsg_i2c_board_info));
|
||||
|
||||
/* This is only useful on a modified machine, but it is valuable
|
||||
* to have it first in order to see debug messages, and so that
|
||||
* it does *not* get removed if platform_add_devices fails!
|
||||
*/
|
||||
(void)platform_device_register(&fsg_uart);
|
||||
|
||||
platform_add_devices(fsg_devices, ARRAY_SIZE(fsg_devices));
|
||||
|
||||
if (request_irq(gpio_to_irq(FSG_RB_GPIO), &fsg_reset_handler,
|
||||
IRQF_DISABLED | IRQF_TRIGGER_LOW,
|
||||
"FSG reset button", NULL) < 0) {
|
||||
|
||||
printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
|
||||
gpio_to_irq(FSG_RB_GPIO));
|
||||
}
|
||||
|
||||
if (request_irq(gpio_to_irq(FSG_SB_GPIO), &fsg_power_handler,
|
||||
IRQF_DISABLED | IRQF_TRIGGER_LOW,
|
||||
"FSG power button", NULL) < 0) {
|
||||
|
||||
printk(KERN_DEBUG "Power Button IRQ %d not available\n",
|
||||
gpio_to_irq(FSG_SB_GPIO));
|
||||
}
|
||||
|
||||
/*
|
||||
* Map in a portion of the flash and read the MAC addresses.
|
||||
* Since it is stored in BE in the flash itself, we need to
|
||||
* byteswap it if we're in LE mode.
|
||||
*/
|
||||
f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000);
|
||||
if (f) {
|
||||
#ifdef __ARMEB__
|
||||
for (i = 0; i < 6; i++) {
|
||||
fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i);
|
||||
fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i);
|
||||
}
|
||||
#else
|
||||
|
||||
/*
|
||||
Endian-swapped reads from unaligned addresses are
|
||||
required to extract the two MACs from the big-endian
|
||||
Redboot config area in flash.
|
||||
*/
|
||||
|
||||
fsg_plat_eth[0].hwaddr[0] = readb(f + 0x3C0421);
|
||||
fsg_plat_eth[0].hwaddr[1] = readb(f + 0x3C0420);
|
||||
fsg_plat_eth[0].hwaddr[2] = readb(f + 0x3C0427);
|
||||
fsg_plat_eth[0].hwaddr[3] = readb(f + 0x3C0426);
|
||||
fsg_plat_eth[0].hwaddr[4] = readb(f + 0x3C0425);
|
||||
fsg_plat_eth[0].hwaddr[5] = readb(f + 0x3C0424);
|
||||
|
||||
fsg_plat_eth[1].hwaddr[0] = readb(f + 0x3C0439);
|
||||
fsg_plat_eth[1].hwaddr[1] = readb(f + 0x3C043F);
|
||||
fsg_plat_eth[1].hwaddr[2] = readb(f + 0x3C043E);
|
||||
fsg_plat_eth[1].hwaddr[3] = readb(f + 0x3C043D);
|
||||
fsg_plat_eth[1].hwaddr[4] = readb(f + 0x3C043C);
|
||||
fsg_plat_eth[1].hwaddr[5] = readb(f + 0x3C0443);
|
||||
#endif
|
||||
iounmap(f);
|
||||
}
|
||||
printk(KERN_INFO "FSG: Using MAC address %s for port 0\n",
|
||||
print_mac(mac_buf, fsg_plat_eth[0].hwaddr));
|
||||
printk(KERN_INFO "FSG: Using MAC address %s for port 1\n",
|
||||
print_mac(mac_buf, fsg_plat_eth[1].hwaddr));
|
||||
|
||||
}
|
||||
|
||||
MACHINE_START(FSG, "Freecom FSG-3")
|
||||
/* Maintainer: www.nslu2-linux.org */
|
||||
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
|
||||
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
|
||||
.map_io = ixp4xx_map_io,
|
||||
.init_irq = ixp4xx_init_irq,
|
||||
.timer = &ixp4xx_timer,
|
||||
.boot_params = 0x0100,
|
||||
.init_machine = fsg_init,
|
||||
MACHINE_END
|
||||
|
||||
|
|
@ -0,0 +1,50 @@
|
|||
/*
|
||||
* include/asm-arm/arch-ixp4xx/fsg.h
|
||||
*
|
||||
* Freecom FSG-3 platform specific definitions
|
||||
*
|
||||
* Author: Rod Whitby <rod@whitby.id.au>
|
||||
* Author: Tomasz Chmielewski <mangoo@wpkg.org>
|
||||
* Maintainers: http://www.nslu2-linux.org
|
||||
*
|
||||
* Based on coyote.h by
|
||||
* Copyright 2004 (c) MontaVista, Software, Inc.
|
||||
*
|
||||
* This file is licensed under the terms of the GNU General Public
|
||||
* License version 2. This program is licensed "as is" without any
|
||||
* warranty of any kind, whether express or implied.
|
||||
*/
|
||||
|
||||
#ifndef __ASM_ARCH_HARDWARE_H__
|
||||
#error "Do not include this directly, instead #include <asm/hardware.h>"
|
||||
#endif
|
||||
|
||||
#define FSG_SDA_PIN 12
|
||||
#define FSG_SCL_PIN 13
|
||||
|
||||
/*
|
||||
* FSG PCI IRQs
|
||||
*/
|
||||
#define FSG_PCI_MAX_DEV 3
|
||||
#define FSG_PCI_IRQ_LINES 3
|
||||
|
||||
|
||||
/* PCI controller GPIO to IRQ pin mappings */
|
||||
#define FSG_PCI_INTA_PIN 6
|
||||
#define FSG_PCI_INTB_PIN 7
|
||||
#define FSG_PCI_INTC_PIN 5
|
||||
|
||||
/* Buttons */
|
||||
|
||||
#define FSG_SB_GPIO 4 /* sync button */
|
||||
#define FSG_RB_GPIO 9 /* reset button */
|
||||
#define FSG_UB_GPIO 10 /* usb button */
|
||||
|
||||
/* LEDs */
|
||||
|
||||
#define FSG_LED_WLAN_BIT 0
|
||||
#define FSG_LED_WAN_BIT 1
|
||||
#define FSG_LED_SATA_BIT 2
|
||||
#define FSG_LED_USB_BIT 4
|
||||
#define FSG_LED_RING_BIT 5
|
||||
#define FSG_LED_SYNC_BIT 7
|
||||
|
|
@ -45,5 +45,6 @@
|
|||
#include "nslu2.h"
|
||||
#include "nas100d.h"
|
||||
#include "dsmg600.h"
|
||||
#include "fsg.h"
|
||||
|
||||
#endif /* _ASM_ARCH_HARDWARE_H */
|
||||
|
|
|
|||
|
|
@ -128,4 +128,11 @@
|
|||
#define IRQ_DSMG600_PCI_INTE IRQ_IXP4XX_GPIO7
|
||||
#define IRQ_DSMG600_PCI_INTF IRQ_IXP4XX_GPIO6
|
||||
|
||||
/*
|
||||
* Freecom FSG-3 Board IRQs
|
||||
*/
|
||||
#define IRQ_FSG_PCI_INTA IRQ_IXP4XX_GPIO6
|
||||
#define IRQ_FSG_PCI_INTB IRQ_IXP4XX_GPIO7
|
||||
#define IRQ_FSG_PCI_INTC IRQ_IXP4XX_GPIO5
|
||||
|
||||
#endif
|
||||
|
|
|
|||
Loading…
Reference in New Issue