diff --git a/drivers/staging/dwc2/core.h b/drivers/staging/dwc2/core.h index ecfcad83f767..9102f66d0111 100644 --- a/drivers/staging/dwc2/core.h +++ b/drivers/staging/dwc2/core.h @@ -68,19 +68,18 @@ enum dwc2_lx_state { /** * struct dwc2_core_params - Parameters for configuring the core * - * @otg_cap: Specifies the OTG capabilities. The driver will - * automatically detect the value for this parameter if - * none is specified. - * 0 - HNP and SRP capable (default) + * @otg_cap: Specifies the OTG capabilities. + * 0 - HNP and SRP capable * 1 - SRP Only capable - * 2 - No HNP/SRP capable + * 2 - No HNP/SRP capable (always available) + * Defaults to best available option (0, 1, then 2) * @otg_ver: OTG version supported - * 0 - 1.3 + * 0 - 1.3 (default) * 1 - 2.0 * @dma_enable: Specifies whether to use slave or DMA mode for accessing * the data FIFOs. The driver will automatically detect the * value for this parameter if none is specified. - * 0 - Slave + * 0 - Slave (always available) * 1 - DMA (default, if available) * @dma_desc_enable: When DMA mode is enabled, specifies whether to use * address DMA mode or descriptor DMA mode for accessing @@ -91,29 +90,47 @@ enum dwc2_lx_state { * @speed: Specifies the maximum speed of operation in host and * device mode. The actual speed depends on the speed of * the attached device and the value of phy_type. - * 0 - High Speed (default) + * 0 - High Speed + * (default when phy_type is UTMI+ or ULPI) * 1 - Full Speed + * (default when phy_type is Full Speed) * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters - * 1 - Allow dynamic FIFO sizing (default) + * 1 - Allow dynamic FIFO sizing (default, if available) * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs * are enabled * @host_rx_fifo_size: Number of 4-byte words in the Rx FIFO in host mode when * dynamic FIFO sizing is enabled - * 16 to 32768 (default 1024) + * 16 to 32768 + * Actual maximum value is autodetected and also + * the default. * @host_nperio_tx_fifo_size: Number of 4-byte words in the non-periodic Tx FIFO * in host mode when dynamic FIFO sizing is enabled - * 16 to 32768 (default 1024) + * 16 to 32768 + * Actual maximum value is autodetected and also + * the default. * @host_perio_tx_fifo_size: Number of 4-byte words in the periodic Tx FIFO in * host mode when dynamic FIFO sizing is enabled - * 16 to 32768 (default 1024) + * 16 to 32768 + * Actual maximum value is autodetected and also + * the default. * @max_transfer_size: The maximum transfer size supported, in bytes - * 2047 to 65,535 (default 65,535) + * 2047 to 65,535 + * Actual maximum value is autodetected and also + * the default. * @max_packet_count: The maximum number of packets in a transfer - * 15 to 511 (default 511) + * 15 to 511 + * Actual maximum value is autodetected and also + * the default. * @host_channels: The number of host channel registers to use - * 1 to 16 (default 12) + * 1 to 16 + * Actual maximum value is autodetected and also + * the default. * @phy_type: Specifies the type of PHY interface to use. By default, * the driver will automatically detect the phy_type. + * 0 - Full Speed Phy + * 1 - UTMI+ Phy + * 2 - ULPI Phy + * Defaults to best available option (2, 1, then 0) * @phy_utmi_width: Specifies the UTMI+ Data Width (in bits). This parameter * is applicable for a phy_type of UTMI+ or ULPI. (For a * ULPI phy_type, this parameter indicates the data width @@ -122,7 +139,7 @@ enum dwc2_lx_state { * parameter was set to "8 and 16 bits", meaning that the * core has been configured to work at either data path * width. - * 8 or 16 (default 16) + * 8 or 16 (default 16 if available) * @phy_ulpi_ddr: Specifies whether the ULPI operates at double or single * data rate. This parameter is only applicable if phy_type * is ULPI. @@ -132,35 +149,51 @@ enum dwc2_lx_state { * data bus * @phy_ulpi_ext_vbus: For a ULPI phy, specifies whether to use the internal or * external supply to drive the VBus + * 0 - Internal supply (default) + * 1 - External supply * @i2c_enable: Specifies whether to use the I2Cinterface for a full * speed PHY. This parameter is only applicable if phy_type * is FS. * 0 - No (default) * 1 - Yes - * @ulpi_fs_ls: True to make ULPI phy operate in FS/LS mode only + * @ulpi_fs_ls: Make ULPI phy operate in FS/LS mode only + * 0 - No (default) + * 1 - Yes * @host_support_fs_ls_low_power: Specifies whether low power mode is supported * when attached to a Full Speed or Low Speed device in * host mode. * 0 - Don't support low power mode (default) * 1 - Support low power mode * @host_ls_low_power_phy_clk: Specifies the PHY clock rate in low power mode - * when connected to a Low Speed device in host mode. This - * parameter is applicable only if - * host_support_fs_ls_low_power is enabled. If phy_type is - * set to FS then defaults to 6 MHZ otherwise 48 MHZ. + * when connected to a Low Speed device in host + * mode. This parameter is applicable only if + * host_support_fs_ls_low_power is enabled. * 0 - 48 MHz + * (default when phy_type is UTMI+ or ULPI) * 1 - 6 MHz - * @ts_dline: True to enable Term Select Dline pulsing - * @reload_ctl: True to allow dynamic reloading of HFIR register during - * runtime + * (default when phy_type is Full Speed) + * @ts_dline: Enable Term Select Dline pulsing + * 0 - No (default) + * 1 - Yes + * @reload_ctl: Allow dynamic reloading of HFIR register during runtime + * 0 - No (default for core < 2.92a) + * 1 - Yes (default for core >= 2.92a) * @ahbcfg: This field allows the default value of the GAHBCFG * register to be overridden - * -1 - GAHBCFG value will not be overridden + * -1 - GAHBCFG value will be set to 0x06 + * (INCR4, default) * all others - GAHBCFG value will be overridden with * this value + * Not all bits can be controlled like this, the + * bits defined by GAHBCFG_CTRL_MASK are controlled + * by the driver and are ignored in this + * configuration value. * * The following parameters may be specified when starting the module. These - * parameters define how the DWC_otg controller should be configured. + * parameters define how the DWC_otg controller should be configured. A + * value of -1 (or any other out of range value) for any parameter means + * to read the value from hardware (if possible) or use the builtin + * default described above. */ struct dwc2_core_params { /*