Merge branch 'fortglx/3.4/clocksource' of git://git.linaro.org/people/jstultz/linux into timers/core

drivers/clocksource/acpi_pm.c

@@ -23,6 +23,7 @@
 #include <linux/init.h>
 #include <linux/pci.h>
 #include <linux/delay.h>
+#include <linux/async.h>
 #include <asm/io.h>
 
 /*
@@ -179,17 +180,15 @@ static int verify_pmtmr_rate(void)
 /* Number of reads we try to get two different values */
 #define ACPI_PM_READ_CHECKS 10000
 
-static int __init init_acpi_pm_clocksource(void)
+static void __init acpi_pm_clocksource_async(void *unused, async_cookie_t cookie)
 {
 	cycle_t value1, value2;
 	unsigned int i, j = 0;
 
-	if (!pmtmr_ioport)
-		return -ENODEV;
 
 	/* "verify" this timing source: */
 	for (j = 0; j < ACPI_PM_MONOTONICITY_CHECKS; j++) {
-		udelay(100 * j);
+		usleep_range(100 * j, 100 * j + 100);
 		value1 = clocksource_acpi_pm.read(&clocksource_acpi_pm);
 		for (i = 0; i < ACPI_PM_READ_CHECKS; i++) {
 			value2 = clocksource_acpi_pm.read(&clocksource_acpi_pm);
@@ -203,25 +202,34 @@ static int __init init_acpi_pm_clocksource(void)
 			       " 0x%#llx, 0x%#llx - aborting.\n",
 			       value1, value2);
 			pmtmr_ioport = 0;
-			return -EINVAL;
+			return;
 		}
 		if (i == ACPI_PM_READ_CHECKS) {
 			printk(KERN_INFO "PM-Timer failed consistency check "
 			       " (0x%#llx) - aborting.\n", value1);
 			pmtmr_ioport = 0;
-			return -ENODEV;
+			return;
 		}
 	}
 
 	if (verify_pmtmr_rate() != 0){
 		pmtmr_ioport = 0;
-		return -ENODEV;
+		return;
 	}
 
-	return clocksource_register_hz(&clocksource_acpi_pm,
+	clocksource_register_hz(&clocksource_acpi_pm,
 						PMTMR_TICKS_PER_SEC);
 }
 
+static int __init init_acpi_pm_clocksource(void)
+{
+	if (!pmtmr_ioport)
+		return -ENODEV;
+
+	async_schedule(acpi_pm_clocksource_async, NULL);
+	return 0;
+}
+
 /* We use fs_initcall because we want the PCI fixups to have run
  * but we still need to load before device_initcall
  */

drivers/clocksource/clksrc-dbx500-prcmu.c

@@ -52,7 +52,6 @@ static struct clocksource clocksource_dbx500_prcmu = {
 	.name		= "dbx500-prcmu-timer",
 	.rating		= 300,
 	.read		= clksrc_dbx500_prcmu_read,
-	.shift		= 10,
 	.mask		= CLOCKSOURCE_MASK(32),
 	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
 };
@@ -90,7 +89,5 @@ void __init clksrc_dbx500_prcmu_init(void __iomem *base)
 	setup_sched_clock(dbx500_prcmu_sched_clock_read,
 			 32, RATE_32K);
 #endif
-	clocksource_calc_mult_shift(&clocksource_dbx500_prcmu,
-				    RATE_32K, SCHED_CLOCK_MIN_WRAP);
-	clocksource_register(&clocksource_dbx500_prcmu);
+	clocksource_register_hz(&clocksource_dbx500_prcmu, RATE_32K);
 }

drivers/clocksource/cyclone.c

@@ -55,11 +55,11 @@ static int __init init_cyclone_clocksource(void)
 	}
 	/* even on 64bit systems, this is only 32bits: */
 	base = readl(reg);
+	iounmap(reg);
 	if (!base) {
 		printk(KERN_ERR "Summit chipset: Could not find valid CBAR value.\n");
 		return -ENODEV;
 	}
-	iounmap(reg);
 
 	/* setup PMCC: */
 	offset = base + CYCLONE_PMCC_OFFSET;

drivers/clocksource/scx200_hrt.c

@@ -49,9 +49,6 @@ static cycle_t read_hrt(struct clocksource *cs)
 	return (cycle_t) inl(scx200_cb_base + SCx200_TIMER_OFFSET);
 }
 
-#define HRT_SHIFT_1	22
-#define HRT_SHIFT_27	26
-
 static struct clocksource cs_hrt = {
 	.name		= "scx200_hrt",
 	.rating		= 250,
@@ -63,6 +60,7 @@ static struct clocksource cs_hrt = {
 
 static int __init init_hrt_clocksource(void)
 {
+	u32 freq;
 	/* Make sure scx200 has initialized the configuration block */
 	if (!scx200_cb_present())
 		return -ENODEV;
@@ -71,7 +69,7 @@ static int __init init_hrt_clocksource(void)
 	if (!request_region(scx200_cb_base + SCx200_TIMER_OFFSET,
 			    SCx200_TIMER_SIZE,
 			    "NatSemi SCx200 High-Resolution Timer")) {
-		printk(KERN_WARNING NAME ": unable to lock timer region\n");
+		pr_warn("unable to lock timer region\n");
 		return -ENODEV;
 	}
 
@@ -79,19 +77,15 @@ static int __init init_hrt_clocksource(void)
 	outb(HR_TMEN | (mhz27 ? HR_TMCLKSEL : 0),
 	     scx200_cb_base + SCx200_TMCNFG_OFFSET);
 
-	if (mhz27) {
-		cs_hrt.shift = HRT_SHIFT_27;
-		cs_hrt.mult = clocksource_hz2mult((HRT_FREQ + ppm) * 27,
-						  cs_hrt.shift);
-	} else {
-		cs_hrt.shift = HRT_SHIFT_1;
-		cs_hrt.mult = clocksource_hz2mult(HRT_FREQ + ppm,
-						  cs_hrt.shift);
-	}
+	freq = (HRT_FREQ + ppm);
+	if (mhz27)
+		freq *= 27;
+
+	pr_info("enabling scx200 high-res timer (%s MHz +%d ppm)\n",
 	printk(KERN_INFO "enabling scx200 high-res timer (%s MHz +%d ppm)\n",
 		mhz27 ? "27":"1", ppm);
 
-	return clocksource_register(&cs_hrt);
+	return clocksource_register_hz(&cs_hrt, freq);
 }
 
 module_init(init_hrt_clocksource);

include/linux/clocksource.h

@@ -319,13 +319,6 @@ static inline void __clocksource_updatefreq_khz(struct clocksource *cs, u32 khz)
 	__clocksource_updatefreq_scale(cs, 1000, khz);
 }
 
-static inline void
-clocksource_calc_mult_shift(struct clocksource *cs, u32 freq, u32 minsec)
-{
-	return clocks_calc_mult_shift(&cs->mult, &cs->shift, freq,
-				      NSEC_PER_SEC, minsec);
-}
-
 #ifdef CONFIG_GENERIC_TIME_VSYSCALL
 extern void
 update_vsyscall(struct timespec *ts, struct timespec *wtm,