Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits)
  ARM: Eliminate decompressor -Dstatic= PIC hack
  ARM: 5958/1: ARM: U300: fix inverted clk round rate
  ARM: 5956/1: misplaced parentheses
  ARM: 5955/1: ep93xx: move timer defines into core.c and document
  ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c
  ARM: 5953/1: ep93xx: fix broken build of clock.c
  ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig
  ARM: 5949/1: NUC900 add gpio virtual memory map
  ARM: 5948/1: Enable timer0 to time4 clock support for nuc910
  ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
  ARM: make_coherent(): fix problems with highpte, part 2
  MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself
  ARM: 5945/1: ep93xx: include correct irq.h in core.c
  ARM: 5933/1: amba-pl011: support hardware flow control
  ARM: 5930/1: Add PKMAP area description to memory.txt.
  ARM: 5929/1: Add checks to detect overlap of memory regions.
  ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
  ARM: 5927/1: Make delimiters of DMA area globally visibly.
  ARM: 5926/1: Add "Virtual kernel memory..." printout.
  ARM: 5920/1: OMAP4: Enable L2 Cache
  ...

Fix up trivial conflict in arch/arm/mach-mx25/clock.c

Documentation/arm/memory.txt

@@ -59,7 +59,11 @@ PAGE_OFFSET	high_memory-1	Kernel direct-mapped RAM region.
 				This maps the platforms RAM, and typically
 				maps all platform RAM in a 1:1 relationship.
 
-TASK_SIZE	PAGE_OFFSET-1	Kernel module space
+PKMAP_BASE	PAGE_OFFSET-1	Permanent kernel mappings
+				One way of mapping HIGHMEM pages into kernel
+				space.
+
+MODULES_VADDR	MODULES_END-1	Kernel module space
 				Kernel modules inserted via insmod are
 				placed here using dynamic mappings.
 

Documentation/cachetlb.txt

@@ -88,12 +88,12 @@ changes occur:
 	This is used primarily during fault processing.
 
 5) void update_mmu_cache(struct vm_area_struct *vma,
-			 unsigned long address, pte_t pte)
+			 unsigned long address, pte_t *ptep)
 
 	At the end of every page fault, this routine is invoked to
 	tell the architecture specific code that a translation
-	described by "pte" now exists at virtual address "address"
+	now exists at virtual address "address" for address space
-	for address space "vma->vm_mm", in the software page tables.
+	"vma->vm_mm", in the software page tables.
 
 	A port may use this information in any way it so chooses.
 	For example, it could use this event to pre-load TLB

arch/alpha/include/asm/pgtable.h

@@ -329,7 +329,7 @@ extern pgd_t swapper_pg_dir[1024];
  * tables contain all the necessary information.
  */
 extern inline void update_mmu_cache(struct vm_area_struct * vma,
-	unsigned long address, pte_t pte)
+	unsigned long address, pte_t *ptep)
 {
 }
 

arch/arm/Kconfig

@@ -12,6 +12,7 @@ config ARM
 	select HAVE_IDE
 	select RTC_LIB
 	select SYS_SUPPORTS_APM_EMULATION
+	select GENERIC_ATOMIC64 if (!CPU_32v6K)
 	select HAVE_OPROFILE
 	select HAVE_ARCH_KGDB
 	select HAVE_KPROBES if (!XIP_KERNEL)
@@ -20,6 +21,8 @@ config ARM
 	select HAVE_GENERIC_DMA_COHERENT
 	select HAVE_KERNEL_GZIP
 	select HAVE_KERNEL_LZO
+	select HAVE_PERF_EVENTS
+	select PERF_USE_VMALLOC
 	help
 	  The ARM series is a line of low-power-consumption RISC chip designs
 	  licensed by ARM Ltd and targeted at embedded applications and
@@ -52,6 +55,9 @@ config HAVE_TCM
 	bool
 	select GENERIC_ALLOCATOR
 
+config HAVE_PROC_CPU
+	bool
+
 config NO_IOPORT
 	bool
 
@@ -161,6 +167,11 @@ config ARCH_MTD_XIP
 config GENERIC_HARDIRQS_NO__DO_IRQ
 	def_bool y
 
+config ARM_L1_CACHE_SHIFT_6
+	bool
+	help
+	  Setting ARM L1 cache line size to 64 Bytes.
+
 if OPROFILE
 
 config OPROFILE_ARMV6
@@ -550,10 +561,20 @@ config ARCH_W90X900
 	  <http://www.nuvoton.com/hq/enu/ProductAndSales/ProductLines/
 		ConsumerElectronicsIC/ARMMicrocontroller/ARMMicrocontroller>
 
+config ARCH_NUC93X
+	bool "Nuvoton NUC93X CPU"
+	select CPU_ARM926T
+	select HAVE_CLK
+	select COMMON_CLKDEV
+	help
+	  Support for Nuvoton (Winbond logic dept.) NUC93X MCU,The NUC93X is a
+	  low-power and high performance MPEG-4/JPEG multimedia controller chip.
+
 config ARCH_PNX4008
 	bool "Philips Nexperia PNX4008 Mobile"
 	select CPU_ARM926T
 	select HAVE_CLK
+	select COMMON_CLKDEV
 	help
 	  This enables support for Philips PNX4008 mobile platform.
 
@@ -638,6 +659,7 @@ config ARCH_S5PC1XX
 	select GENERIC_GPIO
 	select HAVE_CLK
 	select CPU_V7
+	select ARM_L1_CACHE_SHIFT_6
 	help
 	  Samsung S5PC1XX series based systems
 
@@ -785,6 +807,8 @@ source "arch/arm/plat-nomadik/Kconfig"
 
 source "arch/arm/mach-ns9xxx/Kconfig"
 
+source "arch/arm/mach-nuc93x/Kconfig"
+
 source "arch/arm/plat-omap/Kconfig"
 
 source "arch/arm/mach-omap1/Kconfig"
@@ -867,6 +891,11 @@ config XSCALE_PMU
 	depends on CPU_XSCALE && !XSCALE_PMU_TIMER
 	default y
 
+config CPU_HAS_PMU
+	depends on CPU_V6 || CPU_V7 || XSCALE_PMU
+	default y
+	bool
+
 if !MMU
 source "arch/arm/Kconfig-nommu"
 endif
@@ -921,6 +950,19 @@ config ARM_ERRATA_460075
 	  ACTLR register. Note that setting specific bits in the ACTLR register
 	  may not be available in non-secure mode.
 
+config PL310_ERRATA_588369
+	bool "Clean & Invalidate maintenance operations do not invalidate clean lines"
+	depends on CACHE_L2X0 && ARCH_OMAP4
+	help
+	   The PL310 L2 cache controller implements three types of Clean &
+	   Invalidate maintenance operations: by Physical Address
+	   (offset 0x7F0), by Index/Way (0x7F8) and by Way (0x7FC).
+	   They are architecturally defined to behave as the execution of a
+	   clean operation followed immediately by an invalidate operation,
+	   both performing to the same memory location. This functionality
+	   is not correctly implemented in PL310 as clean lines are not
+	   invalidated as a result of these operations. Note that this errata
+	   uses Texas Instrument's secure monitor api.
 endmenu
 
 source "arch/arm/common/Kconfig"
@@ -1171,6 +1213,14 @@ config HIGHPTE
 	depends on HIGHMEM
 	depends on !OUTER_CACHE
 
+config HW_PERF_EVENTS
+	bool "Enable hardware performance counter support for perf events"
+	depends on PERF_EVENTS && CPU_HAS_PMU && (CPU_V6 || CPU_V7)
+	default y
+	help
+	  Enable hardware performance counter support for perf events. If
+	  disabled, perf events will use software events only.
+
 source "mm/Kconfig"
 
 config LEDS
@@ -1230,6 +1280,7 @@ config ALIGNMENT_TRAP
 	bool
 	depends on CPU_CP15_MMU
 	default y if !ARCH_EBSA110
+	select HAVE_PROC_CPU if PROC_FS
 	help
 	  ARM processors cannot fetch/store information which is not
 	  naturally aligned on the bus, i.e., a 4 byte fetch must start at an

arch/arm/Makefile

@@ -171,6 +171,7 @@ machine-$(CONFIG_ARCH_U300)		:= u300
 machine-$(CONFIG_ARCH_U8500)		:= ux500
 machine-$(CONFIG_ARCH_VERSATILE)	:= versatile
 machine-$(CONFIG_ARCH_W90X900)		:= w90x900
+machine-$(CONFIG_ARCH_NUC93X)		:= nuc93x
 machine-$(CONFIG_FOOTBRIDGE)		:= footbridge
 
 # Platform directory name.  This list is sorted alphanumerically

arch/arm/boot/compressed/Makefile

@@ -5,7 +5,7 @@
 #
 
 HEAD	= head.o
-OBJS	= misc.o
+OBJS	= misc.o decompress.o
 FONTC	= $(srctree)/drivers/video/console/font_acorn_8x8.c
 
 #
@@ -106,10 +106,6 @@ lib1funcs = $(obj)/lib1funcs.o
 $(obj)/lib1funcs.S: $(srctree)/arch/$(SRCARCH)/lib/lib1funcs.S FORCE
 	$(call cmd,shipped)
 
-# Don't allow any static data in misc.o, which
-# would otherwise mess up our GOT table
-CFLAGS_misc.o := -Dstatic=
-
 $(obj)/vmlinux: $(obj)/vmlinux.lds $(obj)/$(HEAD) $(obj)/piggy.$(suffix_y).o \
 	 	$(addprefix $(obj)/, $(OBJS)) $(lib1funcs) FORCE
 	$(call if_changed,ld)

arch/arm/boot/compressed/decompress.c

@@ -0,0 +1,45 @@
+#define _LINUX_STRING_H_
+
+#include <linux/compiler.h>	/* for inline */
+#include <linux/types.h>	/* for size_t */
+#include <linux/stddef.h>	/* for NULL */
+#include <linux/linkage.h>
+#include <asm/string.h>
+
+extern unsigned long free_mem_ptr;
+extern unsigned long free_mem_end_ptr;
+extern void error(char *);
+
+#define STATIC static
+
+#define ARCH_HAS_DECOMP_WDOG
+
+/* Diagnostic functions */
+#ifdef DEBUG
+#  define Assert(cond,msg) {if(!(cond)) error(msg);}
+#  define Trace(x) fprintf x
+#  define Tracev(x) {if (verbose) fprintf x ;}
+#  define Tracevv(x) {if (verbose>1) fprintf x ;}
+#  define Tracec(c,x) {if (verbose && (c)) fprintf x ;}
+#  define Tracecv(c,x) {if (verbose>1 && (c)) fprintf x ;}
+#else
+#  define Assert(cond,msg)
+#  define Trace(x)
+#  define Tracev(x)
+#  define Tracevv(x)
+#  define Tracec(c,x)
+#  define Tracecv(c,x)
+#endif
+
+#ifdef CONFIG_KERNEL_GZIP
+#include "../../../../lib/decompress_inflate.c"
+#endif
+
+#ifdef CONFIG_KERNEL_LZO
+#include "../../../../lib/decompress_unlzo.c"
+#endif
+
+void do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x))
+{
+	decompress(input, len, NULL, NULL, output, NULL, error);
+}

arch/arm/boot/compressed/head.S

@@ -22,13 +22,13 @@
 #if defined(CONFIG_DEBUG_ICEDCC)
 
 #ifdef CONFIG_CPU_V6
-		.macro	loadsp, rb
+		.macro	loadsp, rb, tmp
 		.endm
 		.macro	writeb, ch, rb
 		mcr	p14, 0, \ch, c0, c5, 0
 		.endm
 #elif defined(CONFIG_CPU_V7)
-		.macro	loadsp, rb
+		.macro	loadsp, rb, tmp
 		.endm
 		.macro	writeb, ch, rb
 wait:		mrc	p14, 0, pc, c0, c1, 0
@@ -36,13 +36,13 @@ wait:		mrc	p14, 0, pc, c0, c1, 0
 		mcr	p14, 0, \ch, c0, c5, 0
 		.endm
 #elif defined(CONFIG_CPU_XSCALE)
-		.macro	loadsp, rb
+		.macro	loadsp, rb, tmp
 		.endm
 		.macro	writeb, ch, rb
 		mcr	p14, 0, \ch, c8, c0, 0
 		.endm
 #else
-		.macro	loadsp, rb
+		.macro	loadsp, rb, tmp
 		.endm
 		.macro	writeb, ch, rb
 		mcr	p14, 0, \ch, c1, c0, 0
@@ -58,7 +58,7 @@ wait:		mrc	p14, 0, pc, c0, c1, 0
 		.endm
 
 #if defined(CONFIG_ARCH_SA1100)
-		.macro	loadsp, rb
+		.macro	loadsp, rb, tmp
 		mov	\rb, #0x80000000	@ physical base address
 #ifdef CONFIG_DEBUG_LL_SER3
 		add	\rb, \rb, #0x00050000	@ Ser3
@@ -67,13 +67,13 @@ wait:		mrc	p14, 0, pc, c0, c1, 0
 #endif
 		.endm
 #elif defined(CONFIG_ARCH_S3C2410)
-		.macro loadsp, rb
+		.macro loadsp, rb, tmp
 		mov	\rb, #0x50000000
 		add	\rb, \rb, #0x4000 * CONFIG_S3C_LOWLEVEL_UART_PORT
 		.endm
 #else
-		.macro	loadsp,	rb
+		.macro	loadsp,	rb, tmp
-		addruart \rb
+		addruart \rb, \tmp
 		.endm
 #endif
 #endif
@@ -1025,7 +1025,7 @@ phex:		adr	r3, phexbuf
 		strb	r2, [r3, r1]
 		b	1b
 
-puts:		loadsp	r3
+puts:		loadsp	r3, r1
 1:		ldrb	r2, [r0], #1
 		teq	r2, #0
 		moveq	pc, lr
@@ -1042,7 +1042,7 @@ puts:		loadsp	r3
 putc:
 		mov	r2, r0
 		mov	r0, #0
-		loadsp	r3
+		loadsp	r3, r1
 		b	2b
 
 memdump:	mov	r12, r0

arch/arm/boot/compressed/misc.c

@@ -23,8 +23,8 @@ unsigned int __machine_arch_type;
 #include <linux/compiler.h>	/* for inline */
 #include <linux/types.h>	/* for size_t */
 #include <linux/stddef.h>	/* for NULL */
-#include <asm/string.h>
 #include <linux/linkage.h>
+#include <asm/string.h>
 
 #include <asm/unaligned.h>
 
@@ -117,57 +117,7 @@ static void putstr(const char *ptr)
 
 #endif
 
-#define __ptr_t void *
+void *memcpy(void *__dest, __const void *__src, size_t __n)
-
-#define memzero(s,n) __memzero(s,n)
-
-/*
- * Optimised C version of memzero for the ARM.
- */
-void __memzero (__ptr_t s, size_t n)
-{
-	union { void *vp; unsigned long *ulp; unsigned char *ucp; } u;
-	int i;
-
-	u.vp = s;
-
-	for (i = n >> 5; i > 0; i--) {
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-	}
-
-	if (n & 1 << 4) {
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-	}
-
-	if (n & 1 << 3) {
-		*u.ulp++ = 0;
-		*u.ulp++ = 0;
-	}
-
-	if (n & 1 << 2)
-		*u.ulp++ = 0;
-
-	if (n & 1 << 1) {
-		*u.ucp++ = 0;
-		*u.ucp++ = 0;
-	}
-
-	if (n & 1)
-		*u.ucp++ = 0;
-}
-
-static inline __ptr_t memcpy(__ptr_t __dest, __const __ptr_t __src,
-			    size_t __n)
 {
 	int i = 0;
 	unsigned char *d = (unsigned char *)__dest, *s = (unsigned char *)__src;
@@ -204,59 +154,20 @@ static inline __ptr_t memcpy(__ptr_t __dest, __const __ptr_t __src,
 /*
  * gzip delarations
  */
-#define STATIC static
-
-/* Diagnostic functions */
-#ifdef DEBUG
-#  define Assert(cond,msg) {if(!(cond)) error(msg);}
-#  define Trace(x) fprintf x
-#  define Tracev(x) {if (verbose) fprintf x ;}
-#  define Tracevv(x) {if (verbose>1) fprintf x ;}
-#  define Tracec(c,x) {if (verbose && (c)) fprintf x ;}
-#  define Tracecv(c,x) {if (verbose>1 && (c)) fprintf x ;}
-#else
-#  define Assert(cond,msg)
-#  define Trace(x)
-#  define Tracev(x)
-#  define Tracevv(x)
-#  define Tracec(c,x)
-#  define Tracecv(c,x)
-#endif
-
-static void error(char *m);
-
 extern char input_data[];
 extern char input_data_end[];
 
-static unsigned char *output_data;
+unsigned char *output_data;
-static unsigned long output_ptr;
+unsigned long output_ptr;
 
-static void error(char *m);
+unsigned long free_mem_ptr;
-
+unsigned long free_mem_end_ptr;
-static void putstr(const char *);
-
-static unsigned long free_mem_ptr;
-static unsigned long free_mem_end_ptr;
-
-#ifdef STANDALONE_DEBUG
-#define NO_INFLATE_MALLOC
-#endif
-
-#define ARCH_HAS_DECOMP_WDOG
-
-#ifdef CONFIG_KERNEL_GZIP
-#include "../../../../lib/decompress_inflate.c"
-#endif
-
-#ifdef CONFIG_KERNEL_LZO
-#include "../../../../lib/decompress_unlzo.c"
-#endif
 
 #ifndef arch_error
 #define arch_error(x)
 #endif
 
-static void error(char *x)
+void error(char *x)
 {
 	arch_error(x);
 
@@ -272,6 +183,8 @@ asmlinkage void __div0(void)
 	error("Attempting division by 0!");
 }
 
+extern void do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x));
+
 #ifndef STANDALONE_DEBUG
 
 unsigned long
@@ -292,8 +205,8 @@ decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
 	output_ptr = get_unaligned_le32(tmp);
 
 	putstr("Uncompressing Linux...");
-	decompress(input_data, input_data_end - input_data,
+	do_decompress(input_data, input_data_end - input_data,
-			NULL, NULL, output_data, NULL, error);
+			output_data, error);
 	putstr(" done, booting the kernel.\n");
 	return output_ptr;
 }

arch/arm/boot/compressed/vmlinux.lds.in

@@ -14,6 +14,13 @@ SECTIONS
   /DISCARD/ : {
     *(.ARM.exidx*)
     *(.ARM.extab*)
+    /*
+     * Discard any r/w data - this produces a link error if we have any,
+     * which is required for PIC decompression.  Local data generates
+     * GOTOFF relocations, which prevents it being relocated independently
+     * of the text/got segments.
+     */
+    *(.data)
   }
 
   . = TEXT_START;
@@ -40,7 +47,6 @@ SECTIONS
   .got			: { *(.got) }
   _got_end = .;
   .got.plt		: { *(.got.plt) }
-  .data			: { *(.data) }
   _edata = .;
 
   . = BSS_START;

arch/arm/common/clkdev.c

@@ -99,6 +99,16 @@ void clkdev_add(struct clk_lookup *cl)
 }
 EXPORT_SYMBOL(clkdev_add);
 
+void __init clkdev_add_table(struct clk_lookup *cl, size_t num)
+{
+	mutex_lock(&clocks_mutex);
+	while (num--) {
+		list_add_tail(&cl->node, &clocks);
+		cl++;
+	}
+	mutex_unlock(&clocks_mutex);
+}
+
 #define MAX_DEV_ID	20
 #define MAX_CON_ID	16
 

arch/arm/common/dmabounce.c

@@ -277,7 +277,7 @@ static inline dma_addr_t map_single(struct device *dev, void *ptr, size_t size,
 		 * We don't need to sync the DMA buffer since
 		 * it was allocated via the coherent allocators.
 		 */
-		dma_cache_maint(ptr, size, dir);
+		__dma_single_cpu_to_dev(ptr, size, dir);
 	}
 
 	return dma_addr;
@@ -315,6 +315,8 @@ static inline void unmap_single(struct device *dev, dma_addr_t dma_addr,
 			__cpuc_flush_dcache_area(ptr, size);
 		}
 		free_safe_buffer(dev->archdata.dmabounce, buf);
+	} else {
+		__dma_single_dev_to_cpu(dma_to_virt(dev, dma_addr), size, dir);
 	}
 }
 

arch/arm/common/vic.c

@@ -18,6 +18,7 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
+
 #include <linux/init.h>
 #include <linux/list.h>
 #include <linux/io.h>
@@ -28,48 +29,6 @@
 #include <asm/mach/irq.h>
 #include <asm/hardware/vic.h>
 
-static void vic_ack_irq(unsigned int irq)
-{
-	void __iomem *base = get_irq_chip_data(irq);
-	irq &= 31;
-	writel(1 << irq, base + VIC_INT_ENABLE_CLEAR);
-	/* moreover, clear the soft-triggered, in case it was the reason */
-	writel(1 << irq, base + VIC_INT_SOFT_CLEAR);
-}
-
-static void vic_mask_irq(unsigned int irq)
-{
-	void __iomem *base = get_irq_chip_data(irq);
-	irq &= 31;
-	writel(1 << irq, base + VIC_INT_ENABLE_CLEAR);
-}
-
-static void vic_unmask_irq(unsigned int irq)
-{
-	void __iomem *base = get_irq_chip_data(irq);
-	irq &= 31;
-	writel(1 << irq, base + VIC_INT_ENABLE);
-}
-
-/**
- * vic_init2 - common initialisation code
- * @base: Base of the VIC.
- *
- * Common initialisation code for registeration
- * and resume.
-*/
-static void vic_init2(void __iomem *base)
-{
-	int i;
-
-	for (i = 0; i < 16; i++) {
-		void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
-		writel(VIC_VECT_CNTL_ENABLE | i, reg);
-	}
-
-	writel(32, base + VIC_PL190_DEF_VECT_ADDR);
-}
-
 #if defined(CONFIG_PM)
 /**
  * struct vic_device - VIC PM device
@@ -99,13 +58,34 @@ struct vic_device {
 /* we cannot allocate memory when VICs are initially registered */
 static struct vic_device vic_devices[CONFIG_ARM_VIC_NR];
 
+static int vic_id;
+
 static inline struct vic_device *to_vic(struct sys_device *sys)
 {
 	return container_of(sys, struct vic_device, sysdev);
 }
+#endif /* CONFIG_PM */
 
-static int vic_id;
+/**
+ * vic_init2 - common initialisation code
+ * @base: Base of the VIC.
+ *
+ * Common initialisation code for registeration
+ * and resume.
+*/
+static void vic_init2(void __iomem *base)
+{
+	int i;
 
+	for (i = 0; i < 16; i++) {
+		void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
+		writel(VIC_VECT_CNTL_ENABLE | i, reg);
+	}
+
+	writel(32, base + VIC_PL190_DEF_VECT_ADDR);
+}
+
+#if defined(CONFIG_PM)
 static int vic_class_resume(struct sys_device *dev)
 {
 	struct vic_device *vic = to_vic(dev);
@@ -158,31 +138,6 @@ struct sysdev_class vic_class = {
 	.resume		= vic_class_resume,
 };
 
-/**
- * vic_pm_register - Register a VIC for later power management control
- * @base: The base address of the VIC.
- * @irq: The base IRQ for the VIC.
- * @resume_sources: bitmask of interrupts allowed for resume sources.
- *
- * Register the VIC with the system device tree so that it can be notified
- * of suspend and resume requests and ensure that the correct actions are
- * taken to re-instate the settings on resume.
- */
-static void __init vic_pm_register(void __iomem *base, unsigned int irq, u32 resume_sources)
-{
-	struct vic_device *v;
-
-	if (vic_id >= ARRAY_SIZE(vic_devices))
-		printk(KERN_ERR "%s: too few VICs, increase CONFIG_ARM_VIC_NR\n", __func__);
-	else {
-		v = &vic_devices[vic_id];
-		v->base = base;
-		v->resume_sources = resume_sources;
-		v->irq = irq;
-		vic_id++;
-	}
-}
-
 /**
  * vic_pm_init - initicall to register VIC pm
  *
@@ -219,9 +174,60 @@ static int __init vic_pm_init(void)
 
 	return 0;
 }
-
 late_initcall(vic_pm_init);
 
+/**
+ * vic_pm_register - Register a VIC for later power management control
+ * @base: The base address of the VIC.
+ * @irq: The base IRQ for the VIC.
+ * @resume_sources: bitmask of interrupts allowed for resume sources.
+ *
+ * Register the VIC with the system device tree so that it can be notified
+ * of suspend and resume requests and ensure that the correct actions are
+ * taken to re-instate the settings on resume.
+ */
+static void __init vic_pm_register(void __iomem *base, unsigned int irq, u32 resume_sources)
+{
+	struct vic_device *v;
+
+	if (vic_id >= ARRAY_SIZE(vic_devices))
+		printk(KERN_ERR "%s: too few VICs, increase CONFIG_ARM_VIC_NR\n", __func__);
+	else {
+		v = &vic_devices[vic_id];
+		v->base = base;
+		v->resume_sources = resume_sources;
+		v->irq = irq;
+		vic_id++;
+	}
+}
+#else
+static inline void vic_pm_register(void __iomem *base, unsigned int irq, u32 arg1) { }
+#endif /* CONFIG_PM */
+
+static void vic_ack_irq(unsigned int irq)
+{
+	void __iomem *base = get_irq_chip_data(irq);
+	irq &= 31;
+	writel(1 << irq, base + VIC_INT_ENABLE_CLEAR);
+	/* moreover, clear the soft-triggered, in case it was the reason */
+	writel(1 << irq, base + VIC_INT_SOFT_CLEAR);
+}
+
+static void vic_mask_irq(unsigned int irq)
+{
+	void __iomem *base = get_irq_chip_data(irq);
+	irq &= 31;
+	writel(1 << irq, base + VIC_INT_ENABLE_CLEAR);
+}
+
+static void vic_unmask_irq(unsigned int irq)
+{
+	void __iomem *base = get_irq_chip_data(irq);
+	irq &= 31;
+	writel(1 << irq, base + VIC_INT_ENABLE);
+}
+
+#if defined(CONFIG_PM)
 static struct vic_device *vic_from_irq(unsigned int irq)
 {
         struct vic_device *v = vic_devices;
@@ -255,10 +261,7 @@ static int vic_set_wake(unsigned int irq, unsigned int on)
 
 	return 0;
 }
-
 #else
-static inline void vic_pm_register(void __iomem *base, unsigned int irq, u32 arg1) { }
-
 #define vic_set_wake NULL
 #endif /* CONFIG_PM */
 
@@ -270,80 +273,6 @@ static struct irq_chip vic_chip = {
 	.set_wake = vic_set_wake,
 };
 
-/* The PL190 cell from ARM has been modified by ST, so handle both here */
-static void vik_init_st(void __iomem *base, unsigned int irq_start,
-			 u32 vic_sources);
-
-/**
- * vic_init - initialise a vectored interrupt controller
- * @base: iomem base address
- * @irq_start: starting interrupt number, must be muliple of 32
- * @vic_sources: bitmask of interrupt sources to allow
- * @resume_sources: bitmask of interrupt sources to allow for resume
- */
-void __init vic_init(void __iomem *base, unsigned int irq_start,
-		     u32 vic_sources, u32 resume_sources)
-{
-	unsigned int i;
-	u32 cellid = 0;
-	enum amba_vendor vendor;
-
-	/* Identify which VIC cell this one is, by reading the ID */
-	for (i = 0; i < 4; i++) {
-		u32 addr = ((u32)base & PAGE_MASK) + 0xfe0 + (i * 4);
-		cellid |= (readl(addr) & 0xff) << (8 * i);
-	}
-	vendor = (cellid >> 12) & 0xff;
-	printk(KERN_INFO "VIC @%p: id 0x%08x, vendor 0x%02x\n",
-	       base, cellid, vendor);
-
-	switch(vendor) {
-	case AMBA_VENDOR_ST:
-		vik_init_st(base, irq_start, vic_sources);
-		return;
-	default:
-		printk(KERN_WARNING "VIC: unknown vendor, continuing anyways\n");
-		/* fall through */
-	case AMBA_VENDOR_ARM:
-		break;
-	}
-
-	/* Disable all interrupts initially. */
-
-	writel(0, base + VIC_INT_SELECT);
-	writel(0, base + VIC_INT_ENABLE);
-	writel(~0, base + VIC_INT_ENABLE_CLEAR);
-	writel(0, base + VIC_IRQ_STATUS);
-	writel(0, base + VIC_ITCR);
-	writel(~0, base + VIC_INT_SOFT_CLEAR);
-
-	/*
-	 * Make sure we clear all existing interrupts
-	 */
-	writel(0, base + VIC_PL190_VECT_ADDR);
-	for (i = 0; i < 19; i++) {
-		unsigned int value;
-
-		value = readl(base + VIC_PL190_VECT_ADDR);
-		writel(value, base + VIC_PL190_VECT_ADDR);
-	}
-
-	vic_init2(base);
-
-	for (i = 0; i < 32; i++) {
-		if (vic_sources & (1 << i)) {
-			unsigned int irq = irq_start + i;
-
-			set_irq_chip(irq, &vic_chip);
-			set_irq_chip_data(irq, base);
-			set_irq_handler(irq, handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-		}
-	}
-
-	vic_pm_register(base, irq_start, resume_sources);
-}
-
 /*
  * The PL190 cell from ARM has been modified by ST to handle 64 interrupts.
  * The original cell has 32 interrupts, while the modified one has 64,
@@ -351,7 +280,7 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
  * the probe function is called twice, with base set to offset 000
  *  and 020 within the page. We call this "second block".
  */
-static void __init vik_init_st(void __iomem *base, unsigned int irq_start,
+static void __init vic_init_st(void __iomem *base, unsigned int irq_start,
 				u32 vic_sources)
 {
 	unsigned int i;
@@ -400,3 +329,73 @@ static void __init vik_init_st(void __iomem *base, unsigned int irq_start,
 		}
 	}
 }
+
+/**
+ * vic_init - initialise a vectored interrupt controller
+ * @base: iomem base address
+ * @irq_start: starting interrupt number, must be muliple of 32
+ * @vic_sources: bitmask of interrupt sources to allow
+ * @resume_sources: bitmask of interrupt sources to allow for resume
+ */
+void __init vic_init(void __iomem *base, unsigned int irq_start,
+		     u32 vic_sources, u32 resume_sources)
+{
+	unsigned int i;
+	u32 cellid = 0;
+	enum amba_vendor vendor;
+
+	/* Identify which VIC cell this one is, by reading the ID */
+	for (i = 0; i < 4; i++) {
+		u32 addr = ((u32)base & PAGE_MASK) + 0xfe0 + (i * 4);
+		cellid |= (readl(addr) & 0xff) << (8 * i);
+	}
+	vendor = (cellid >> 12) & 0xff;
+	printk(KERN_INFO "VIC @%p: id 0x%08x, vendor 0x%02x\n",
+	       base, cellid, vendor);
+
+	switch(vendor) {
+	case AMBA_VENDOR_ST:
+		vic_init_st(base, irq_start, vic_sources);
+		return;
+	default:
+		printk(KERN_WARNING "VIC: unknown vendor, continuing anyways\n");
+		/* fall through */
+	case AMBA_VENDOR_ARM:
+		break;
+	}
+
+	/* Disable all interrupts initially. */
+
+	writel(0, base + VIC_INT_SELECT);
+	writel(0, base + VIC_INT_ENABLE);
+	writel(~0, base + VIC_INT_ENABLE_CLEAR);
+	writel(0, base + VIC_IRQ_STATUS);
+	writel(0, base + VIC_ITCR);
+	writel(~0, base + VIC_INT_SOFT_CLEAR);
+
+	/*
+	 * Make sure we clear all existing interrupts
+	 */
+	writel(0, base + VIC_PL190_VECT_ADDR);
+	for (i = 0; i < 19; i++) {
+		unsigned int value;
+
+		value = readl(base + VIC_PL190_VECT_ADDR);
+		writel(value, base + VIC_PL190_VECT_ADDR);
+	}
+
+	vic_init2(base);
+
+	for (i = 0; i < 32; i++) {
+		if (vic_sources & (1 << i)) {
+			unsigned int irq = irq_start + i;
+
+			set_irq_chip(irq, &vic_chip);
+			set_irq_chip_data(irq, base);
+			set_irq_handler(irq, handle_level_irq);
+			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		}
+	}
+
+	vic_pm_register(base, irq_start, resume_sources);
+}

arch/arm/configs/omap_4430sdp_defconfig

@@ -242,10 +242,13 @@ CONFIG_CPU_CP15_MMU=y
 # CONFIG_CPU_DCACHE_DISABLE is not set
 # CONFIG_CPU_BPREDICT_DISABLE is not set
 CONFIG_HAS_TLS_REG=y
+CONFIG_OUTER_CACHE=y
+CONFIG_CACHE_L2X0=y
 CONFIG_ARM_L1_CACHE_SHIFT=5
 # CONFIG_ARM_ERRATA_430973 is not set
 # CONFIG_ARM_ERRATA_458693 is not set
 # CONFIG_ARM_ERRATA_460075 is not set
+CONFIG_PL310_ERRATA_588369=y
 CONFIG_ARM_GIC=y
 
 #

arch/arm/include/asm/atomic.h

@@ -235,6 +235,234 @@ static inline int atomic_add_unless(atomic_t *v, int a, int u)
 #define smp_mb__before_atomic_inc()	smp_mb()
 #define smp_mb__after_atomic_inc()	smp_mb()
 
+#ifndef CONFIG_GENERIC_ATOMIC64
+typedef struct {
+	u64 __aligned(8) counter;
+} atomic64_t;
+
+#define ATOMIC64_INIT(i) { (i) }
+
+static inline u64 atomic64_read(atomic64_t *v)
+{
+	u64 result;
+
+	__asm__ __volatile__("@ atomic64_read\n"
+"	ldrexd	%0, %H0, [%1]"
+	: "=&r" (result)
+	: "r" (&v->counter)
+	);
+
+	return result;
+}
+
+static inline void atomic64_set(atomic64_t *v, u64 i)
+{
+	u64 tmp;
+
+	__asm__ __volatile__("@ atomic64_set\n"
+"1:	ldrexd	%0, %H0, [%1]\n"
+"	strexd	%0, %2, %H2, [%1]\n"
+"	teq	%0, #0\n"
+"	bne	1b"
+	: "=&r" (tmp)
+	: "r" (&v->counter), "r" (i)
+	: "cc");
+}
+
+static inline void atomic64_add(u64 i, atomic64_t *v)
+{
+	u64 result;
+	unsigned long tmp;
+
+	__asm__ __volatile__("@ atomic64_add\n"
+"1:	ldrexd	%0, %H0, [%2]\n"
+"	adds	%0, %0, %3\n"
+"	adc	%H0, %H0, %H3\n"
+"	strexd	%1, %0, %H0, [%2]\n"
+"	teq	%1, #0\n"
+"	bne	1b"
+	: "=&r" (result), "=&r" (tmp)
+	: "r" (&v->counter), "r" (i)
+	: "cc");
+}
+
+static inline u64 atomic64_add_return(u64 i, atomic64_t *v)
+{
+	u64 result;
+	unsigned long tmp;
+
+	smp_mb();
+
+	__asm__ __volatile__("@ atomic64_add_return\n"
+"1:	ldrexd	%0, %H0, [%2]\n"
+"	adds	%0, %0, %3\n"
+"	adc	%H0, %H0, %H3\n"
+"	strexd	%1, %0, %H0, [%2]\n"
+"	teq	%1, #0\n"
+"	bne	1b"
+	: "=&r" (result), "=&r" (tmp)
+	: "r" (&v->counter), "r" (i)
+	: "cc");
+
+	smp_mb();
+
+	return result;
+}
+
+static inline void atomic64_sub(u64 i, atomic64_t *v)
+{
+	u64 result;
+	unsigned long tmp;
+
+	__asm__ __volatile__("@ atomic64_sub\n"
+"1:	ldrexd	%0, %H0, [%2]\n"
+"	subs	%0, %0, %3\n"
+"	sbc	%H0, %H0, %H3\n"
+"	strexd	%1, %0, %H0, [%2]\n"
+"	teq	%1, #0\n"
+"	bne	1b"
+	: "=&r" (result), "=&r" (tmp)
+	: "r" (&v->counter), "r" (i)
+	: "cc");
+}
+
+static inline u64 atomic64_sub_return(u64 i, atomic64_t *v)
+{
+	u64 result;
+	unsigned long tmp;
+
+	smp_mb();
+
+	__asm__ __volatile__("@ atomic64_sub_return\n"
+"1:	ldrexd	%0, %H0, [%2]\n"
+"	subs	%0, %0, %3\n"
+"	sbc	%H0, %H0, %H3\n"
+"	strexd	%1, %0, %H0, [%2]\n"
+"	teq	%1, #0\n"
+"	bne	1b"
+	: "=&r" (result), "=&r" (tmp)
+	: "r" (&v->counter), "r" (i)
+	: "cc");
+
+	smp_mb();
+
+	return result;
+}
+
+static inline u64 atomic64_cmpxchg(atomic64_t *ptr, u64 old, u64 new)
+{
+	u64 oldval;
+	unsigned long res;
+
+	smp_mb();
+
+	do {
+		__asm__ __volatile__("@ atomic64_cmpxchg\n"
+		"ldrexd		%1, %H1, [%2]\n"
+		"mov		%0, #0\n"
+		"teq		%1, %3\n"
+		"teqeq		%H1, %H3\n"
+		"strexdeq	%0, %4, %H4, [%2]"
+		: "=&r" (res), "=&r" (oldval)
+		: "r" (&ptr->counter), "r" (old), "r" (new)
+		: "cc");
+	} while (res);
+
+	smp_mb();
+
+	return oldval;
+}
+
+static inline u64 atomic64_xchg(atomic64_t *ptr, u64 new)
+{
+	u64 result;
+	unsigned long tmp;
+
+	smp_mb();
+
+	__asm__ __volatile__("@ atomic64_xchg\n"
+"1:	ldrexd	%0, %H0, [%2]\n"
+"	strexd	%1, %3, %H3, [%2]\n"
+"	teq	%1, #0\n"
+"	bne	1b"
+	: "=&r" (result), "=&r" (tmp)
+	: "r" (&ptr->counter), "r" (new)
+	: "cc");
+
+	smp_mb();
+
+	return result;
+}
+
+static inline u64 atomic64_dec_if_positive(atomic64_t *v)
+{
+	u64 result;
+	unsigned long tmp;
+
+	smp_mb();
+
+	__asm__ __volatile__("@ atomic64_dec_if_positive\n"
+"1:	ldrexd	%0, %H0, [%2]\n"
+"	subs	%0, %0, #1\n"
+"	sbc	%H0, %H0, #0\n"
+"	teq	%H0, #0\n"
+"	bmi	2f\n"
+"	strexd	%1, %0, %H0, [%2]\n"
+"	teq	%1, #0\n"
+"	bne	1b\n"
+"2:"
+	: "=&r" (result), "=&r" (tmp)
+	: "r" (&v->counter)
+	: "cc");
+
+	smp_mb();
+
+	return result;
+}
+
+static inline int atomic64_add_unless(atomic64_t *v, u64 a, u64 u)
+{
+	u64 val;
+	unsigned long tmp;
+	int ret = 1;
+
+	smp_mb();
+
+	__asm__ __volatile__("@ atomic64_add_unless\n"
+"1:	ldrexd	%0, %H0, [%3]\n"
+"	teq	%0, %4\n"
+"	teqeq	%H0, %H4\n"
+"	moveq	%1, #0\n"
+"	beq	2f\n"
+"	adds	%0, %0, %5\n"
+"	adc	%H0, %H0, %H5\n"
+"	strexd	%2, %0, %H0, [%3]\n"
+"	teq	%2, #0\n"
+"	bne	1b\n"
+"2:"
+	: "=&r" (val), "=&r" (ret), "=&r" (tmp)
+	: "r" (&v->counter), "r" (u), "r" (a)
+	: "cc");
+
+	if (ret)
+		smp_mb();
+
+	return ret;
+}
+
+#define atomic64_add_negative(a, v)	(atomic64_add_return((a), (v)) < 0)
+#define atomic64_inc(v)			atomic64_add(1LL, (v))
+#define atomic64_inc_return(v)		atomic64_add_return(1LL, (v))
+#define atomic64_inc_and_test(v)	(atomic64_inc_return(v) == 0)
+#define atomic64_sub_and_test(a, v)	(atomic64_sub_return((a), (v)) == 0)
+#define atomic64_dec(v)			atomic64_sub(1LL, (v))
+#define atomic64_dec_return(v)		atomic64_sub_return(1LL, (v))
+#define atomic64_dec_and_test(v)	(atomic64_dec_return((v)) == 0)
+#define atomic64_inc_not_zero(v)	atomic64_add_unless((v), 1LL, 0LL)
+
+#else /* !CONFIG_GENERIC_ATOMIC64 */
+#include <asm-generic/atomic64.h>
+#endif
 #include <asm-generic/atomic-long.h>
 #endif
 #endif

arch/arm/include/asm/cacheflush.h

@@ -197,21 +197,6 @@
  *	DMA Cache Coherency
  *	===================
  *
- *	dma_inv_range(start, end)
- *
- *		Invalidate (discard) the specified virtual address range.
- *		May not write back any entries.  If 'start' or 'end'
- *		are not cache line aligned, those lines must be written
- *		back.
- *		- start  - virtual start address
- *		- end    - virtual end address
- *
- *	dma_clean_range(start, end)
- *
- *		Clean (write back) the specified virtual address range.
- *		- start  - virtual start address
- *		- end    - virtual end address
- *
  *	dma_flush_range(start, end)
  *
  *		Clean and invalidate the specified virtual address range.
@@ -228,8 +213,9 @@ struct cpu_cache_fns {
 	void (*coherent_user_range)(unsigned long, unsigned long);
 	void (*flush_kern_dcache_area)(void *, size_t);
 
-	void (*dma_inv_range)(const void *, const void *);
+	void (*dma_map_area)(const void *, size_t, int);
-	void (*dma_clean_range)(const void *, const void *);
+	void (*dma_unmap_area)(const void *, size_t, int);
+
 	void (*dma_flush_range)(const void *, const void *);
 };
 
@@ -259,8 +245,8 @@ extern struct cpu_cache_fns cpu_cache;
  * is visible to DMA, or data written by DMA to system memory is
  * visible to the CPU.
  */
-#define dmac_inv_range			cpu_cache.dma_inv_range
+#define dmac_map_area			cpu_cache.dma_map_area
-#define dmac_clean_range		cpu_cache.dma_clean_range
+#define dmac_unmap_area		cpu_cache.dma_unmap_area
 #define dmac_flush_range		cpu_cache.dma_flush_range
 
 #else
@@ -285,12 +271,12 @@ extern void __cpuc_flush_dcache_area(void *, size_t);
  * is visible to DMA, or data written by DMA to system memory is
  * visible to the CPU.
  */
-#define dmac_inv_range			__glue(_CACHE,_dma_inv_range)
+#define dmac_map_area			__glue(_CACHE,_dma_map_area)
-#define dmac_clean_range		__glue(_CACHE,_dma_clean_range)
+#define dmac_unmap_area		__glue(_CACHE,_dma_unmap_area)
 #define dmac_flush_range		__glue(_CACHE,_dma_flush_range)
 
-extern void dmac_inv_range(const void *, const void *);
+extern void dmac_map_area(const void *, size_t, int);
-extern void dmac_clean_range(const void *, const void *);
+extern void dmac_unmap_area(const void *, size_t, int);
 extern void dmac_flush_range(const void *, const void *);
 
 #endif
@@ -331,12 +317,8 @@ static inline void outer_flush_range(unsigned long start, unsigned long end)
  * processes address space.  Really, we want to allow our "user
  * space" model to handle this.
  */
-#define copy_to_user_page(vma, page, vaddr, dst, src, len) \
+extern void copy_to_user_page(struct vm_area_struct *, struct page *,
-	do {							\
+	unsigned long, void *, const void *, unsigned long);
-		memcpy(dst, src, len);				\
-		flush_ptrace_access(vma, page, vaddr, dst, len, 1);\
-	} while (0)
-
 #define copy_from_user_page(vma, page, vaddr, dst, src, len) \
 	do {							\
 		memcpy(dst, src, len);				\
@@ -370,17 +352,6 @@ vivt_flush_cache_page(struct vm_area_struct *vma, unsigned long user_addr, unsig
 	}
 }
 
-static inline void
-vivt_flush_ptrace_access(struct vm_area_struct *vma, struct page *page,
-			 unsigned long uaddr, void *kaddr,
-			 unsigned long len, int write)
-{
-	if (cpumask_test_cpu(smp_processor_id(), mm_cpumask(vma->vm_mm))) {
-		unsigned long addr = (unsigned long)kaddr;
-		__cpuc_coherent_kern_range(addr, addr + len);
-	}
-}
-
 #ifndef CONFIG_CPU_CACHE_VIPT
 #define flush_cache_mm(mm) \
 		vivt_flush_cache_mm(mm)
@@ -388,15 +359,10 @@ vivt_flush_ptrace_access(struct vm_area_struct *vma, struct page *page,
 		vivt_flush_cache_range(vma,start,end)
 #define flush_cache_page(vma,addr,pfn) \
 		vivt_flush_cache_page(vma,addr,pfn)
-#define flush_ptrace_access(vma,page,ua,ka,len,write) \
-		vivt_flush_ptrace_access(vma,page,ua,ka,len,write)
 #else
 extern void flush_cache_mm(struct mm_struct *mm);
 extern void flush_cache_range(struct vm_area_struct *vma, unsigned long start, unsigned long end);
 extern void flush_cache_page(struct vm_area_struct *vma, unsigned long user_addr, unsigned long pfn);
-extern void flush_ptrace_access(struct vm_area_struct *vma, struct page *page,
-				unsigned long uaddr, void *kaddr,
-				unsigned long len, int write);
 #endif
 
 #define flush_cache_dup_mm(mm) flush_cache_mm(mm)

arch/arm/include/asm/clkdev.h

@@ -27,4 +27,7 @@ struct clk_lookup *clkdev_alloc(struct clk *clk, const char *con_id,
 void clkdev_add(struct clk_lookup *cl);
 void clkdev_drop(struct clk_lookup *cl);
 
+void clkdev_add_table(struct clk_lookup *, size_t);
+int clk_add_alias(const char *, const char *, char *, struct device *);
+
 #endif

arch/arm/include/asm/dma-mapping.h

@@ -57,18 +57,58 @@ static inline dma_addr_t virt_to_dma(struct device *dev, void *addr)
 #endif
 
 /*
- * DMA-consistent mapping functions.  These allocate/free a region of
+ * The DMA API is built upon the notion of "buffer ownership".  A buffer
- * uncached, unwrite-buffered mapped memory space for use with DMA
+ * is either exclusively owned by the CPU (and therefore may be accessed
- * devices.  This is the "generic" version.  The PCI specific version
+ * by it) or exclusively owned by the DMA device.  These helper functions
- * is in pci.h
+ * represent the transitions between these two ownership states.
  *
- * Note: Drivers should NOT use this function directly, as it will break
+ * Note, however, that on later ARMs, this notion does not work due to
- * platforms with CONFIG_DMABOUNCE.
+ * speculative prefetches.  We model our approach on the assumption that
- * Use the driver DMA support - see dma-mapping.h (dma_sync_*)
+ * the CPU does do speculative prefetches, which means we clean caches
+ * before transfers and delay cache invalidation until transfer completion.
+ *
+ * Private support functions: these are not part of the API and are
+ * liable to change.  Drivers must not use these.
  */
-extern void dma_cache_maint(const void *kaddr, size_t size, int rw);
+static inline void __dma_single_cpu_to_dev(const void *kaddr, size_t size,
-extern void dma_cache_maint_page(struct page *page, unsigned long offset,
+	enum dma_data_direction dir)
-				 size_t size, int rw);
+{
+	extern void ___dma_single_cpu_to_dev(const void *, size_t,
+		enum dma_data_direction);
+
+	if (!arch_is_coherent())
+		___dma_single_cpu_to_dev(kaddr, size, dir);
+}
+
+static inline void __dma_single_dev_to_cpu(const void *kaddr, size_t size,
+	enum dma_data_direction dir)
+{
+	extern void ___dma_single_dev_to_cpu(const void *, size_t,
+		enum dma_data_direction);
+
+	if (!arch_is_coherent())
+		___dma_single_dev_to_cpu(kaddr, size, dir);
+}
+
+static inline void __dma_page_cpu_to_dev(struct page *page, unsigned long off,
+	size_t size, enum dma_data_direction dir)
+{
+	extern void ___dma_page_cpu_to_dev(struct page *, unsigned long,
+		size_t, enum dma_data_direction);
+
+	if (!arch_is_coherent())
+		___dma_page_cpu_to_dev(page, off, size, dir);
+}
+
+static inline void __dma_page_dev_to_cpu(struct page *page, unsigned long off,
+	size_t size, enum dma_data_direction dir)
+{
+	extern void ___dma_page_dev_to_cpu(struct page *, unsigned long,
+		size_t, enum dma_data_direction);
+
+	if (!arch_is_coherent())
+		___dma_page_dev_to_cpu(page, off, size, dir);
+}
 
 /*
  * Return whether the given device DMA address mask can be supported
@@ -304,8 +344,7 @@ static inline dma_addr_t dma_map_single(struct device *dev, void *cpu_addr,
 {
 	BUG_ON(!valid_dma_direction(dir));
 
-	if (!arch_is_coherent())
+	__dma_single_cpu_to_dev(cpu_addr, size, dir);
-		dma_cache_maint(cpu_addr, size, dir);
 
 	return virt_to_dma(dev, cpu_addr);
 }
@@ -329,8 +368,7 @@ static inline dma_addr_t dma_map_page(struct device *dev, struct page *page,
 {
 	BUG_ON(!valid_dma_direction(dir));
 
-	if (!arch_is_coherent())
+	__dma_page_cpu_to_dev(page, offset, size, dir);
-		dma_cache_maint_page(page, offset, size, dir);
 
 	return page_to_dma(dev, page) + offset;
 }
@@ -352,7 +390,7 @@ static inline dma_addr_t dma_map_page(struct device *dev, struct page *page,
 static inline void dma_unmap_single(struct device *dev, dma_addr_t handle,
 		size_t size, enum dma_data_direction dir)
 {
-	/* nothing to do */
+	__dma_single_dev_to_cpu(dma_to_virt(dev, handle), size, dir);
 }
 
 /**
@@ -372,7 +410,8 @@ static inline void dma_unmap_single(struct device *dev, dma_addr_t handle,
 static inline void dma_unmap_page(struct device *dev, dma_addr_t handle,
 		size_t size, enum dma_data_direction dir)
 {
-	/* nothing to do */
+	__dma_page_dev_to_cpu(dma_to_page(dev, handle), handle & ~PAGE_MASK,
+		size, dir);
 }
 #endif /* CONFIG_DMABOUNCE */
 
@@ -400,7 +439,10 @@ static inline void dma_sync_single_range_for_cpu(struct device *dev,
 {
 	BUG_ON(!valid_dma_direction(dir));
 
-	dmabounce_sync_for_cpu(dev, handle, offset, size, dir);
+	if (!dmabounce_sync_for_cpu(dev, handle, offset, size, dir))
+		return;
+
+	__dma_single_dev_to_cpu(dma_to_virt(dev, handle) + offset, size, dir);
 }
 
 static inline void dma_sync_single_range_for_device(struct device *dev,
@@ -412,8 +454,7 @@ static inline void dma_sync_single_range_for_device(struct device *dev,
 	if (!dmabounce_sync_for_device(dev, handle, offset, size, dir))
 		return;
 
-	if (!arch_is_coherent())
+	__dma_single_cpu_to_dev(dma_to_virt(dev, handle) + offset, size, dir);
-		dma_cache_maint(dma_to_virt(dev, handle) + offset, size, dir);
 }
 
 static inline void dma_sync_single_for_cpu(struct device *dev,

arch/arm/include/asm/io.h

@@ -69,9 +69,16 @@ extern void __raw_readsl(const void __iomem *addr, void *data, int longlen);
 /*
  * __arm_ioremap takes CPU physical address.
  * __arm_ioremap_pfn takes a Page Frame Number and an offset into that page
+ * The _caller variety takes a __builtin_return_address(0) value for
+ * /proc/vmalloc to use - and should only be used in non-inline functions.
  */
-extern void __iomem * __arm_ioremap_pfn(unsigned long, unsigned long, size_t, unsigned int);
+extern void __iomem *__arm_ioremap_pfn_caller(unsigned long, unsigned long,
-extern void __iomem * __arm_ioremap(unsigned long, size_t, unsigned int);
+	size_t, unsigned int, void *);
+extern void __iomem *__arm_ioremap_caller(unsigned long, size_t, unsigned int,
+	void *);
+
+extern void __iomem *__arm_ioremap_pfn(unsigned long, unsigned long, size_t, unsigned int);
+extern void __iomem *__arm_ioremap(unsigned long, size_t, unsigned int);
 extern void __iounmap(volatile void __iomem *addr);
 
 /*

arch/arm/include/asm/mach/time.h

@@ -46,12 +46,4 @@ struct sys_timer {
 extern struct sys_timer *system_timer;
 extern void timer_tick(void);
 
-/*
- * Kernel time keeping support.
- */
-struct timespec;
-extern int (*set_rtc)(void);
-extern void save_time_delta(struct timespec *delta, struct timespec *rtc);
-extern void restore_time_delta(struct timespec *delta, struct timespec *rtc);
-
 #endif

arch/arm/include/asm/memory.h

@@ -76,6 +76,17 @@
  */
 #define IOREMAP_MAX_ORDER	24
 
+/*
+ * Size of DMA-consistent memory region.  Must be multiple of 2M,
+ * between 2MB and 14MB inclusive.
+ */
+#ifndef CONSISTENT_DMA_SIZE
+#define CONSISTENT_DMA_SIZE 	SZ_2M
+#endif
+
+#define CONSISTENT_END		(0xffe00000UL)
+#define CONSISTENT_BASE		(CONSISTENT_END - CONSISTENT_DMA_SIZE)
+
 #else /* CONFIG_MMU */
 
 /*
@@ -93,11 +104,11 @@
 #endif
 
 #ifndef PHYS_OFFSET
-#define PHYS_OFFSET 		(CONFIG_DRAM_BASE)
+#define PHYS_OFFSET 		UL(CONFIG_DRAM_BASE)
 #endif
 
 #ifndef END_MEM
-#define END_MEM     		(CONFIG_DRAM_BASE + CONFIG_DRAM_SIZE)
+#define END_MEM     		(UL(CONFIG_DRAM_BASE) + CONFIG_DRAM_SIZE)
 #endif
 
 #ifndef PAGE_OFFSET
@@ -112,14 +123,6 @@
 
 #endif /* !CONFIG_MMU */
 
-/*
- * Size of DMA-consistent memory region.  Must be multiple of 2M,
- * between 2MB and 14MB inclusive.
- */
-#ifndef CONSISTENT_DMA_SIZE
-#define CONSISTENT_DMA_SIZE SZ_2M
-#endif
-
 /*
  * Physical vs virtual RAM address space conversion.  These are
  * private definitions which should NOT be used outside memory.h

arch/arm/include/asm/mmu.h

@@ -6,6 +6,7 @@
 typedef struct {
 #ifdef CONFIG_CPU_HAS_ASID
 	unsigned int id;
+	spinlock_t id_lock;
 #endif
 	unsigned int kvm_seq;
 } mm_context_t;

arch/arm/include/asm/mmu_context.h

@@ -43,12 +43,23 @@ void __check_kvm_seq(struct mm_struct *mm);
 #define ASID_FIRST_VERSION	(1 << ASID_BITS)
 
 extern unsigned int cpu_last_asid;
+#ifdef CONFIG_SMP
+DECLARE_PER_CPU(struct mm_struct *, current_mm);
+#endif
 
 void __init_new_context(struct task_struct *tsk, struct mm_struct *mm);
 void __new_context(struct mm_struct *mm);
 
 static inline void check_context(struct mm_struct *mm)
 {
+	/*
+	 * This code is executed with interrupts enabled. Therefore,
+	 * mm->context.id cannot be updated to the latest ASID version
+	 * on a different CPU (and condition below not triggered)
+	 * without first getting an IPI to reset the context. The
+	 * alternative is to take a read_lock on mm->context.id_lock
+	 * (after changing its type to rwlock_t).
+	 */
 	if (unlikely((mm->context.id ^ cpu_last_asid) >> ASID_BITS))
 		__new_context(mm);
 
@@ -108,6 +119,10 @@ switch_mm(struct mm_struct *prev, struct mm_struct *next,
 		__flush_icache_all();
 #endif
 	if (!cpumask_test_and_set_cpu(cpu, mm_cpumask(next)) || prev != next) {
+#ifdef CONFIG_SMP
+		struct mm_struct **crt_mm = &per_cpu(current_mm, cpu);
+		*crt_mm = next;
+#endif
 		check_context(next);
 		cpu_switch_mm(next->pgd, next);
 		if (cache_is_vivt())

arch/arm/include/asm/page.h

@@ -117,11 +117,12 @@
 #endif
 
 struct page;
+struct vm_area_struct;
 
 struct cpu_user_fns {
 	void (*cpu_clear_user_highpage)(struct page *page, unsigned long vaddr);
 	void (*cpu_copy_user_highpage)(struct page *to, struct page *from,
-			unsigned long vaddr);
+			unsigned long vaddr, struct vm_area_struct *vma);
 };
 
 #ifdef MULTI_USER
@@ -137,7 +138,7 @@ extern struct cpu_user_fns cpu_user;
 
 extern void __cpu_clear_user_highpage(struct page *page, unsigned long vaddr);
 extern void __cpu_copy_user_highpage(struct page *to, struct page *from,
-			unsigned long vaddr);
+			unsigned long vaddr, struct vm_area_struct *vma);
 #endif
 
 #define clear_user_highpage(page,vaddr)		\
@@ -145,7 +146,7 @@ extern void __cpu_copy_user_highpage(struct page *to, struct page *from,
 
 #define __HAVE_ARCH_COPY_USER_HIGHPAGE
 #define copy_user_highpage(to,from,vaddr,vma)	\
-	__cpu_copy_user_highpage(to, from, vaddr)
+	__cpu_copy_user_highpage(to, from, vaddr, vma)
 
 #define clear_page(page)	memset((void *)(page), 0, PAGE_SIZE)
 extern void copy_page(void *to, const void *from);

arch/arm/include/asm/perf_event.h

@@ -0,0 +1,31 @@
+/*
+ *  linux/arch/arm/include/asm/perf_event.h
+ *
+ *  Copyright (C) 2009 picoChip Designs Ltd, Jamie Iles
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __ARM_PERF_EVENT_H__
+#define __ARM_PERF_EVENT_H__
+
+/*
+ * NOP: on *most* (read: all supported) ARM platforms, the performance
+ * counter interrupts are regular interrupts and not an NMI. This
+ * means that when we receive the interrupt we can call
+ * perf_event_do_pending() that handles all of the work with
+ * interrupts enabled.
+ */
+static inline void
+set_perf_event_pending(void)
+{
+}
+
+/* ARM performance counters start from 1 (in the cp15 accesses) so use the
+ * same indexes here for consistency. */
+#define PERF_EVENT_INDEX_OFFSET 1
+
+#endif /* __ARM_PERF_EVENT_H__ */

arch/arm/include/asm/pgtable-nommu.h

@@ -86,8 +86,8 @@ extern unsigned int kobjsize(const void *objp);
  * All 32bit addresses are effectively valid for vmalloc...
  * Sort of meaningless for non-VM targets.
  */
-#define	VMALLOC_START	0
+#define	VMALLOC_START	0UL
-#define	VMALLOC_END	0xffffffff
+#define	VMALLOC_END	0xffffffffUL
 
 #define FIRST_USER_ADDRESS      (0)
 

arch/arm/include/asm/pmu.h

@@ -0,0 +1,75 @@
+/*
+ *  linux/arch/arm/include/asm/pmu.h
+ *
+ *  Copyright (C) 2009 picoChip Designs Ltd, Jamie Iles
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __ARM_PMU_H__
+#define __ARM_PMU_H__
+
+#ifdef CONFIG_CPU_HAS_PMU
+
+struct pmu_irqs {
+	const int   *irqs;
+	int	    num_irqs;
+};
+
+/**
+ * reserve_pmu() - reserve the hardware performance counters
+ *
+ * Reserve the hardware performance counters in the system for exclusive use.
+ * The 'struct pmu_irqs' for the system is returned on success, ERR_PTR()
+ * encoded error on failure.
+ */
+extern const struct pmu_irqs *
+reserve_pmu(void);
+
+/**
+ * release_pmu() - Relinquish control of the performance counters
+ *
+ * Release the performance counters and allow someone else to use them.
+ * Callers must have disabled the counters and released IRQs before calling
+ * this. The 'struct pmu_irqs' returned from reserve_pmu() must be passed as
+ * a cookie.
+ */
+extern int
+release_pmu(const struct pmu_irqs *irqs);
+
+/**
+ * init_pmu() - Initialise the PMU.
+ *
+ * Initialise the system ready for PMU enabling. This should typically set the
+ * IRQ affinity and nothing else. The users (oprofile/perf events etc) will do
+ * the actual hardware initialisation.
+ */
+extern int
+init_pmu(void);
+
+#else /* CONFIG_CPU_HAS_PMU */
+
+static inline const struct pmu_irqs *
+reserve_pmu(void)
+{
+	return ERR_PTR(-ENODEV);
+}
+
+static inline int
+release_pmu(const struct pmu_irqs *irqs)
+{
+	return -ENODEV;
+}
+
+static inline int
+init_pmu(void)
+{
+	return -ENODEV;
+}
+
+#endif /* CONFIG_CPU_HAS_PMU */
+
+#endif /* __ARM_PMU_H__ */

arch/arm/include/asm/setup.h

@@ -223,18 +223,6 @@ extern struct meminfo meminfo;
 #define bank_phys_end(bank)	((bank)->start + (bank)->size)
 #define bank_phys_size(bank)	(bank)->size
 
-/*
- * Early command line parameters.
- */
-struct early_params {
-	const char *arg;
-	void (*fn)(char **p);
-};
-
-#define __early_param(name,fn)					\
-static struct early_params __early_##fn __used			\
-__attribute__((__section__(".early_param.init"))) = { name, fn }
-
 #endif  /*  __KERNEL__  */
 
 #endif

arch/arm/include/asm/smp_plat.h

@@ -13,4 +13,9 @@ static inline int tlb_ops_need_broadcast(void)
 	return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2;
 }
 
+static inline int cache_ops_need_broadcast(void)
+{
+	return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 1;
+}
+
 #endif

arch/arm/include/asm/spinlock.h

@@ -5,6 +5,22 @@
 #error SMP not supported on pre-ARMv6 CPUs
 #endif
 
+static inline void dsb_sev(void)
+{
+#if __LINUX_ARM_ARCH__ >= 7
+	__asm__ __volatile__ (
+		"dsb\n"
+		"sev"
+	);
+#elif defined(CONFIG_CPU_32v6K)
+	__asm__ __volatile__ (
+		"mcr p15, 0, %0, c7, c10, 4\n"
+		"sev"
+		: : "r" (0)
+	);
+#endif
+}
+
 /*
  * ARMv6 Spin-locking.
  *
@@ -69,13 +85,11 @@ static inline void arch_spin_unlock(arch_spinlock_t *lock)
 
 	__asm__ __volatile__(
 "	str	%1, [%0]\n"
-#ifdef CONFIG_CPU_32v6K
-"	mcr	p15, 0, %1, c7, c10, 4\n" /* DSB */
-"	sev"
-#endif
 	:
 	: "r" (&lock->lock), "r" (0)
 	: "cc");
+
+	dsb_sev();
 }
 
 /*
@@ -132,13 +146,11 @@ static inline void arch_write_unlock(arch_rwlock_t *rw)
 
 	__asm__ __volatile__(
 	"str	%1, [%0]\n"
-#ifdef CONFIG_CPU_32v6K
-"	mcr	p15, 0, %1, c7, c10, 4\n" /* DSB */
-"	sev\n"
-#endif
 	:
 	: "r" (&rw->lock), "r" (0)
 	: "cc");
+
+	dsb_sev();
 }
 
 /* write_can_lock - would write_trylock() succeed? */
@@ -188,14 +200,12 @@ static inline void arch_read_unlock(arch_rwlock_t *rw)
 "	strex	%1, %0, [%2]\n"
 "	teq	%1, #0\n"
 "	bne	1b"
-#ifdef CONFIG_CPU_32v6K
-"\n	cmp	%0, #0\n"
-"	mcreq   p15, 0, %0, c7, c10, 4\n"
-"	seveq"
-#endif
 	: "=&r" (tmp), "=&r" (tmp2)
 	: "r" (&rw->lock)
 	: "cc");
+
+	if (tmp == 0)
+		dsb_sev();
 }
 
 static inline int arch_read_trylock(arch_rwlock_t *rw)

arch/arm/include/asm/system.h

@@ -73,8 +73,7 @@ extern unsigned int mem_fclk_21285;
 
 struct pt_regs;
 
-void die(const char *msg, struct pt_regs *regs, int err)
+void die(const char *msg, struct pt_regs *regs, int err);
-		__attribute__((noreturn));
 
 struct siginfo;
 void arm_notify_die(const char *str, struct pt_regs *regs, struct siginfo *info,

arch/arm/include/asm/thread_info.h

@@ -115,7 +115,8 @@ extern void iwmmxt_task_restore(struct thread_info *, void *);
 extern void iwmmxt_task_release(struct thread_info *);
 extern void iwmmxt_task_switch(struct thread_info *);
 
-extern void vfp_sync_state(struct thread_info *thread);
+extern void vfp_sync_hwstate(struct thread_info *);
+extern void vfp_flush_hwstate(struct thread_info *);
 
 #endif
 

arch/arm/include/asm/tlbflush.h

@@ -529,7 +529,8 @@ extern void flush_tlb_kernel_range(unsigned long start, unsigned long end);
  * cache entries for the kernels virtual memory range are written
  * back to the page.
  */
-extern void update_mmu_cache(struct vm_area_struct *vma, unsigned long addr, pte_t pte);
+extern void update_mmu_cache(struct vm_area_struct *vma, unsigned long addr,
+	pte_t *ptep);
 
 #endif
 

arch/arm/kernel/Makefile

@@ -17,6 +17,7 @@ obj-y		:= compat.o elf.o entry-armv.o entry-common.o irq.o \
 		   process.o ptrace.o return_address.o setup.o signal.o \
 		   sys_arm.o stacktrace.o time.o traps.o
 
+obj-$(CONFIG_LEDS)		+= leds.o
 obj-$(CONFIG_OC_ETM)		+= etm.o
 
 obj-$(CONFIG_ISA_DMA_API)	+= dma.o
@@ -46,6 +47,8 @@ obj-$(CONFIG_CPU_XSCALE)	+= xscale-cp0.o
 obj-$(CONFIG_CPU_XSC3)		+= xscale-cp0.o
 obj-$(CONFIG_CPU_MOHAWK)	+= xscale-cp0.o
 obj-$(CONFIG_IWMMXT)		+= iwmmxt.o
+obj-$(CONFIG_CPU_HAS_PMU)	+= pmu.o
+obj-$(CONFIG_HW_PERF_EVENTS)	+= perf_event.o
 AFLAGS_iwmmxt.o			:= -Wa,-mcpu=iwmmxt
 
 ifneq ($(CONFIG_ARCH_EBSA110),y)

arch/arm/kernel/asm-offsets.c

@@ -12,6 +12,7 @@
  */
 #include <linux/sched.h>
 #include <linux/mm.h>
+#include <linux/dma-mapping.h>
 #include <asm/mach/arch.h>
 #include <asm/thread_info.h>
 #include <asm/memory.h>
@@ -112,5 +113,9 @@ int main(void)
 #ifdef MULTI_PABORT
   DEFINE(PROCESSOR_PABT_FUNC,	offsetof(struct processor, _prefetch_abort));
 #endif
+  BLANK();
+  DEFINE(DMA_BIDIRECTIONAL,	DMA_BIDIRECTIONAL);
+  DEFINE(DMA_TO_DEVICE,		DMA_TO_DEVICE);
+  DEFINE(DMA_FROM_DEVICE,	DMA_FROM_DEVICE);
   return 0; 
 }

arch/arm/kernel/debug.S

@@ -24,7 +24,7 @@
 
 #if defined(CONFIG_CPU_V6)
 
-		.macro	addruart, rx
+		.macro	addruart, rx, tmp
 		.endm
 
 		.macro	senduart, rd, rx
@@ -51,7 +51,7 @@
 
 #elif defined(CONFIG_CPU_V7)
 
-		.macro	addruart, rx
+		.macro	addruart, rx, tmp
 		.endm
 
 		.macro	senduart, rd, rx
@@ -71,7 +71,7 @@ wait:		mrc	p14, 0, pc, c0, c1, 0
 
 #elif defined(CONFIG_CPU_XSCALE)
 
-		.macro	addruart, rx
+		.macro	addruart, rx, tmp
 		.endm
 
 		.macro	senduart, rd, rx
@@ -98,7 +98,7 @@ wait:		mrc	p14, 0, pc, c0, c1, 0
 
 #else
 
-		.macro	addruart, rx
+		.macro	addruart, rx, tmp
 		.endm
 
 		.macro	senduart, rd, rx
@@ -164,7 +164,7 @@ ENDPROC(printhex2)
 		.ltorg
 
 ENTRY(printascii)
-		addruart r3
+		addruart r3, r1
 		b	2f
 1:		waituart r2, r3
 		senduart r1, r3
@@ -180,7 +180,7 @@ ENTRY(printascii)
 ENDPROC(printascii)
 
 ENTRY(printch)
-		addruart r3
+		addruart r3, r1
 		mov	r1, r0
 		mov	r0, #0
 		b	1b

arch/arm/kernel/leds.c

@@ -0,0 +1,115 @@
+/*
+ * LED support code, ripped out of arch/arm/kernel/time.c
+ *
+ *  Copyright (C) 1994-2001 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/sysdev.h>
+
+#include <asm/leds.h>
+
+static void dummy_leds_event(led_event_t evt)
+{
+}
+
+void (*leds_event)(led_event_t) = dummy_leds_event;
+
+struct leds_evt_name {
+	const char	name[8];
+	int		on;
+	int		off;
+};
+
+static const struct leds_evt_name evt_names[] = {
+	{ "amber", led_amber_on, led_amber_off },
+	{ "blue",  led_blue_on,  led_blue_off  },
+	{ "green", led_green_on, led_green_off },
+	{ "red",   led_red_on,   led_red_off   },
+};
+
+static ssize_t leds_store(struct sys_device *dev,
+			struct sysdev_attribute *attr,
+			const char *buf, size_t size)
+{
+	int ret = -EINVAL, len = strcspn(buf, " ");
+
+	if (len > 0 && buf[len] == '\0')
+		len--;
+
+	if (strncmp(buf, "claim", len) == 0) {
+		leds_event(led_claim);
+		ret = size;
+	} else if (strncmp(buf, "release", len) == 0) {
+		leds_event(led_release);
+		ret = size;
+	} else {
+		int i;
+
+		for (i = 0; i < ARRAY_SIZE(evt_names); i++) {
+			if (strlen(evt_names[i].name) != len ||
+			    strncmp(buf, evt_names[i].name, len) != 0)
+				continue;
+			if (strncmp(buf+len, " on", 3) == 0) {
+				leds_event(evt_names[i].on);
+				ret = size;
+			} else if (strncmp(buf+len, " off", 4) == 0) {
+				leds_event(evt_names[i].off);
+				ret = size;
+			}
+			break;
+		}
+	}
+	return ret;
+}
+
+static SYSDEV_ATTR(event, 0200, NULL, leds_store);
+
+static int leds_suspend(struct sys_device *dev, pm_message_t state)
+{
+	leds_event(led_stop);
+	return 0;
+}
+
+static int leds_resume(struct sys_device *dev)
+{
+	leds_event(led_start);
+	return 0;
+}
+
+static int leds_shutdown(struct sys_device *dev)
+{
+	leds_event(led_halted);
+	return 0;
+}
+
+static struct sysdev_class leds_sysclass = {
+	.name		= "leds",
+	.shutdown	= leds_shutdown,
+	.suspend	= leds_suspend,
+	.resume		= leds_resume,
+};
+
+static struct sys_device leds_device = {
+	.id		= 0,
+	.cls		= &leds_sysclass,
+};
+
+static int __init leds_init(void)
+{
+	int ret;
+	ret = sysdev_class_register(&leds_sysclass);
+	if (ret == 0)
+		ret = sysdev_register(&leds_device);
+	if (ret == 0)
+		ret = sysdev_create_file(&leds_device, &attr_event);
+	return ret;
+}
+
+device_initcall(leds_init);
+
+EXPORT_SYMBOL(leds_event);

arch/arm/kernel/pmu.c

@@ -0,0 +1,103 @@
+/*
+ *  linux/arch/arm/kernel/pmu.c
+ *
+ *  Copyright (C) 2009 picoChip Designs Ltd, Jamie Iles
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/cpumask.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+
+#include <asm/pmu.h>
+
+/*
+ * Define the IRQs for the system. We could use something like a platform
+ * device but that seems fairly heavyweight for this. Also, the performance
+ * counters can't be removed or hotplugged.
+ *
+ * Ordering is important: init_pmu() will use the ordering to set the affinity
+ * to the corresponding core. e.g. the first interrupt will go to cpu 0, the
+ * second goes to cpu 1 etc.
+ */
+static const int irqs[] = {
+#if defined(CONFIG_ARCH_OMAP2)
+	3,
+#elif defined(CONFIG_ARCH_BCMRING)
+	IRQ_PMUIRQ,
+#elif defined(CONFIG_MACH_REALVIEW_EB)
+	IRQ_EB11MP_PMU_CPU0,
+	IRQ_EB11MP_PMU_CPU1,
+	IRQ_EB11MP_PMU_CPU2,
+	IRQ_EB11MP_PMU_CPU3,
+#elif defined(CONFIG_ARCH_OMAP3)
+	INT_34XX_BENCH_MPU_EMUL,
+#elif defined(CONFIG_ARCH_IOP32X)
+	IRQ_IOP32X_CORE_PMU,
+#elif defined(CONFIG_ARCH_IOP33X)
+	IRQ_IOP33X_CORE_PMU,
+#elif defined(CONFIG_ARCH_PXA)
+	IRQ_PMU,
+#endif
+};
+
+static const struct pmu_irqs pmu_irqs = {
+	.irqs	    = irqs,
+	.num_irqs   = ARRAY_SIZE(irqs),
+};
+
+static volatile long pmu_lock;
+
+const struct pmu_irqs *
+reserve_pmu(void)
+{
+	return test_and_set_bit_lock(0, &pmu_lock) ? ERR_PTR(-EBUSY) :
+		&pmu_irqs;
+}
+EXPORT_SYMBOL_GPL(reserve_pmu);
+
+int
+release_pmu(const struct pmu_irqs *irqs)
+{
+	if (WARN_ON(irqs != &pmu_irqs))
+		return -EINVAL;
+	clear_bit_unlock(0, &pmu_lock);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(release_pmu);
+
+static int
+set_irq_affinity(int irq,
+		 unsigned int cpu)
+{
+#ifdef CONFIG_SMP
+	int err = irq_set_affinity(irq, cpumask_of(cpu));
+	if (err)
+		pr_warning("unable to set irq affinity (irq=%d, cpu=%u)\n",
+			   irq, cpu);
+	return err;
+#else
+	return 0;
+#endif
+}
+
+int
+init_pmu(void)
+{
+	int i, err = 0;
+
+	for (i = 0; i < pmu_irqs.num_irqs; ++i) {
+		err = set_irq_affinity(pmu_irqs.irqs[i], i);
+		if (err)
+			break;
+	}
+
+	return err;
+}
+EXPORT_SYMBOL_GPL(init_pmu);

arch/arm/kernel/ptrace.c

@@ -499,10 +499,41 @@ static struct undef_hook thumb_break_hook = {
 	.fn		= break_trap,
 };
 
+static int thumb2_break_trap(struct pt_regs *regs, unsigned int instr)
+{
+	unsigned int instr2;
+	void __user *pc;
+
+	/* Check the second half of the instruction.  */
+	pc = (void __user *)(instruction_pointer(regs) + 2);
+
+	if (processor_mode(regs) == SVC_MODE) {
+		instr2 = *(u16 *) pc;
+	} else {
+		get_user(instr2, (u16 __user *)pc);
+	}
+
+	if (instr2 == 0xa000) {
+		ptrace_break(current, regs);
+		return 0;
+	} else {
+		return 1;
+	}
+}
+
+static struct undef_hook thumb2_break_hook = {
+	.instr_mask	= 0xffff,
+	.instr_val	= 0xf7f0,
+	.cpsr_mask	= PSR_T_BIT,
+	.cpsr_val	= PSR_T_BIT,
+	.fn		= thumb2_break_trap,
+};
+
 static int __init ptrace_break_init(void)
 {
 	register_undef_hook(&arm_break_hook);
 	register_undef_hook(&thumb_break_hook);
+	register_undef_hook(&thumb2_break_hook);
 	return 0;
 }
 
@@ -669,7 +700,7 @@ static int ptrace_getvfpregs(struct task_struct *tsk, void __user *data)
 	union vfp_state *vfp = &thread->vfpstate;
 	struct user_vfp __user *ufp = data;
 
-	vfp_sync_state(thread);
+	vfp_sync_hwstate(thread);
 
 	/* copy the floating point registers */
 	if (copy_to_user(&ufp->fpregs, &vfp->hard.fpregs,
@@ -692,7 +723,7 @@ static int ptrace_setvfpregs(struct task_struct *tsk, void __user *data)
 	union vfp_state *vfp = &thread->vfpstate;
 	struct user_vfp __user *ufp = data;
 
-	vfp_sync_state(thread);
+	vfp_sync_hwstate(thread);
 
 	/* copy the floating point registers */
 	if (copy_from_user(&vfp->hard.fpregs, &ufp->fpregs,
@@ -703,6 +734,8 @@ static int ptrace_setvfpregs(struct task_struct *tsk, void __user *data)
 	if (get_user(vfp->hard.fpscr, &ufp->fpscr))
 		return -EFAULT;
 
+	vfp_flush_hwstate(thread);
+
 	return 0;
 }
 #endif
@@ -712,26 +745,10 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 	int ret;
 
 	switch (request) {
-		/*
-		 * read word at location "addr" in the child process.
-		 */
-		case PTRACE_PEEKTEXT:
-		case PTRACE_PEEKDATA:
-			ret = generic_ptrace_peekdata(child, addr, data);
-			break;
-
 		case PTRACE_PEEKUSR:
 			ret = ptrace_read_user(child, addr, (unsigned long __user *)data);
 			break;
 
-		/*
-		 * write the word at location addr.
-		 */
-		case PTRACE_POKETEXT:
-		case PTRACE_POKEDATA:
-			ret = generic_ptrace_pokedata(child, addr, data);
-			break;
-
 		case PTRACE_POKEUSR:
 			ret = ptrace_write_user(child, addr, data);
 			break;

arch/arm/kernel/setup.c

@@ -24,6 +24,7 @@
 #include <linux/interrupt.h>
 #include <linux/smp.h>
 #include <linux/fs.h>
+#include <linux/proc_fs.h>
 
 #include <asm/unified.h>
 #include <asm/cpu.h>
@@ -118,7 +119,7 @@ EXPORT_SYMBOL(elf_platform);
 
 static const char *cpu_name;
 static const char *machine_name;
-static char __initdata command_line[COMMAND_LINE_SIZE];
+static char __initdata cmd_line[COMMAND_LINE_SIZE];
 
 static char default_command_line[COMMAND_LINE_SIZE] __initdata = CONFIG_CMDLINE;
 static union { char c[4]; unsigned long l; } endian_test __initdata = { { 'l', '?', '?', 'b' } };
@@ -418,10 +419,11 @@ static int __init arm_add_memory(unsigned long start, unsigned long size)
  * Pick out the memory size.  We look for mem=size@start,
  * where start and size are "size[KkMm]"
  */
-static void __init early_mem(char **p)
+static int __init early_mem(char *p)
 {
 	static int usermem __initdata = 0;
 	unsigned long size, start;
+	char *endp;
 
 	/*
 	 * If the user specifies memory size, we
@@ -434,52 +436,15 @@ static void __init early_mem(char **p)
 	}
 
 	start = PHYS_OFFSET;
-	size  = memparse(*p, p);
+	size  = memparse(p, &endp);
-	if (**p == '@')
+	if (*endp == '@')
-		start = memparse(*p + 1, p);
+		start = memparse(endp + 1, NULL);
 
 	arm_add_memory(start, size);
+
+	return 0;
 }
-__early_param("mem=", early_mem);
+early_param("mem", early_mem);
-
-/*
- * Initial parsing of the command line.
- */
-static void __init parse_cmdline(char **cmdline_p, char *from)
-{
-	char c = ' ', *to = command_line;
-	int len = 0;
-
-	for (;;) {
-		if (c == ' ') {
-			extern struct early_params __early_begin, __early_end;
-			struct early_params *p;
-
-			for (p = &__early_begin; p < &__early_end; p++) {
-				int arglen = strlen(p->arg);
-
-				if (memcmp(from, p->arg, arglen) == 0) {
-					if (to != command_line)
-						to -= 1;
-					from += arglen;
-					p->fn(&from);
-
-					while (*from != ' ' && *from != '\0')
-						from++;
-					break;
-				}
-			}
-		}
-		c = *from++;
-		if (!c)
-			break;
-		if (COMMAND_LINE_SIZE <= ++len)
-			break;
-		*to++ = c;
-	}
-	*to = '\0';
-	*cmdline_p = command_line;
-}
 
 static void __init
 setup_ramdisk(int doload, int prompt, int image_start, unsigned int rd_sz)
@@ -740,9 +705,15 @@ void __init setup_arch(char **cmdline_p)
 	init_mm.end_data   = (unsigned long) _edata;
 	init_mm.brk	   = (unsigned long) _end;
 
-	memcpy(boot_command_line, from, COMMAND_LINE_SIZE);
+	/* parse_early_param needs a boot_command_line */
-	boot_command_line[COMMAND_LINE_SIZE-1] = '\0';
+	strlcpy(boot_command_line, from, COMMAND_LINE_SIZE);
-	parse_cmdline(cmdline_p, from);
+
+	/* populate cmd_line too for later use, preserving boot_command_line */
+	strlcpy(cmd_line, boot_command_line, COMMAND_LINE_SIZE);
+	*cmdline_p = cmd_line;
+
+	parse_early_param();
+
 	paging_init(mdesc);
 	request_standard_resources(&meminfo, mdesc);
 
@@ -783,9 +754,21 @@ static int __init topology_init(void)
 
 	return 0;
 }
-
 subsys_initcall(topology_init);
 
+#ifdef CONFIG_HAVE_PROC_CPU
+static int __init proc_cpu_init(void)
+{
+	struct proc_dir_entry *res;
+
+	res = proc_mkdir("cpu", NULL);
+	if (!res)
+		return -ENOMEM;
+	return 0;
+}
+fs_initcall(proc_cpu_init);
+#endif
+
 static const char *hwcap_str[] = {
 	"swp",
 	"half",

arch/arm/kernel/time.c

@@ -10,11 +10,6 @@
  *
  *  This file contains the ARM-specific time handling details:
  *  reading the RTC at bootup, etc...
- *
- *  1994-07-02  Alan Modra
- *              fixed set_rtc_mmss, fixed time.year for >= 2000, new mktime
- *  1998-12-20  Updated NTP code according to technical memorandum Jan '96
- *              "A Kernel Model for Precision Timekeeping" by Dave Mills
  */
 #include <linux/module.h>
 #include <linux/kernel.h>
@@ -77,11 +72,6 @@ unsigned long profile_pc(struct pt_regs *regs)
 EXPORT_SYMBOL(profile_pc);
 #endif
 
-/*
- * hook for setting the RTC's idea of the current time.
- */
-int (*set_rtc)(void);
-
 #ifndef CONFIG_GENERIC_TIME
 static unsigned long dummy_gettimeoffset(void)
 {
@@ -89,140 +79,6 @@ static unsigned long dummy_gettimeoffset(void)
 }
 #endif
 
-static unsigned long next_rtc_update;
-
-/*
- * If we have an externally synchronized linux clock, then update
- * CMOS clock accordingly every ~11 minutes.  set_rtc() has to be
- * called as close as possible to 500 ms before the new second
- * starts.
- */
-static inline void do_set_rtc(void)
-{
-	if (!ntp_synced() || set_rtc == NULL)
-		return;
-
-	if (next_rtc_update &&
-	    time_before((unsigned long)xtime.tv_sec, next_rtc_update))
-		return;
-
-	if (xtime.tv_nsec < 500000000 - ((unsigned) tick_nsec >> 1) &&
-	    xtime.tv_nsec >= 500000000 + ((unsigned) tick_nsec >> 1))
-		return;
-
-	if (set_rtc())
-		/*
-		 * rtc update failed.  Try again in 60s
-		 */
-		next_rtc_update = xtime.tv_sec + 60;
-	else
-		next_rtc_update = xtime.tv_sec + 660;
-}
-
-#ifdef CONFIG_LEDS
-
-static void dummy_leds_event(led_event_t evt)
-{
-}
-
-void (*leds_event)(led_event_t) = dummy_leds_event;
-
-struct leds_evt_name {
-	const char	name[8];
-	int		on;
-	int		off;
-};
-
-static const struct leds_evt_name evt_names[] = {
-	{ "amber", led_amber_on, led_amber_off },
-	{ "blue",  led_blue_on,  led_blue_off  },
-	{ "green", led_green_on, led_green_off },
-	{ "red",   led_red_on,   led_red_off   },
-};
-
-static ssize_t leds_store(struct sys_device *dev,
-			struct sysdev_attribute *attr,
-			const char *buf, size_t size)
-{
-	int ret = -EINVAL, len = strcspn(buf, " ");
-
-	if (len > 0 && buf[len] == '\0')
-		len--;
-
-	if (strncmp(buf, "claim", len) == 0) {
-		leds_event(led_claim);
-		ret = size;
-	} else if (strncmp(buf, "release", len) == 0) {
-		leds_event(led_release);
-		ret = size;
-	} else {
-		int i;
-
-		for (i = 0; i < ARRAY_SIZE(evt_names); i++) {
-			if (strlen(evt_names[i].name) != len ||
-			    strncmp(buf, evt_names[i].name, len) != 0)
-				continue;
-			if (strncmp(buf+len, " on", 3) == 0) {
-				leds_event(evt_names[i].on);
-				ret = size;
-			} else if (strncmp(buf+len, " off", 4) == 0) {
-				leds_event(evt_names[i].off);
-				ret = size;
-			}
-			break;
-		}
-	}
-	return ret;
-}
-
-static SYSDEV_ATTR(event, 0200, NULL, leds_store);
-
-static int leds_suspend(struct sys_device *dev, pm_message_t state)
-{
-	leds_event(led_stop);
-	return 0;
-}
-
-static int leds_resume(struct sys_device *dev)
-{
-	leds_event(led_start);
-	return 0;
-}
-
-static int leds_shutdown(struct sys_device *dev)
-{
-	leds_event(led_halted);
-	return 0;
-}
-
-static struct sysdev_class leds_sysclass = {
-	.name		= "leds",
-	.shutdown	= leds_shutdown,
-	.suspend	= leds_suspend,
-	.resume		= leds_resume,
-};
-
-static struct sys_device leds_device = {
-	.id		= 0,
-	.cls		= &leds_sysclass,
-};
-
-static int __init leds_init(void)
-{
-	int ret;
-	ret = sysdev_class_register(&leds_sysclass);
-	if (ret == 0)
-		ret = sysdev_register(&leds_device);
-	if (ret == 0)
-		ret = sysdev_create_file(&leds_device, &attr_event);
-	return ret;
-}
-
-device_initcall(leds_init);
-
-EXPORT_SYMBOL(leds_event);
-#endif
-
 #ifdef CONFIG_LEDS_TIMER
 static inline void do_leds(void)
 {
@@ -295,39 +151,6 @@ int do_settimeofday(struct timespec *tv)
 EXPORT_SYMBOL(do_settimeofday);
 #endif /* !CONFIG_GENERIC_TIME */
 
-/**
- * save_time_delta - Save the offset between system time and RTC time
- * @delta: pointer to timespec to store delta
- * @rtc: pointer to timespec for current RTC time
- *
- * Return a delta between the system time and the RTC time, such
- * that system time can be restored later with restore_time_delta()
- */
-void save_time_delta(struct timespec *delta, struct timespec *rtc)
-{
-	set_normalized_timespec(delta,
-				xtime.tv_sec - rtc->tv_sec,
-				xtime.tv_nsec - rtc->tv_nsec);
-}
-EXPORT_SYMBOL(save_time_delta);
-
-/**
- * restore_time_delta - Restore the current system time
- * @delta: delta returned by save_time_delta()
- * @rtc: pointer to timespec for current RTC time
- */
-void restore_time_delta(struct timespec *delta, struct timespec *rtc)
-{
-	struct timespec ts;
-
-	set_normalized_timespec(&ts,
-				delta->tv_sec + rtc->tv_sec,
-				delta->tv_nsec + rtc->tv_nsec);
-
-	do_settimeofday(&ts);
-}
-EXPORT_SYMBOL(restore_time_delta);
-
 #ifndef CONFIG_GENERIC_CLOCKEVENTS
 /*
  * Kernel system timer support.
@@ -336,7 +159,6 @@ void timer_tick(void)
 {
 	profile_tick(CPU_PROFILING);
 	do_leds();
-	do_set_rtc();
 	write_seqlock(&xtime_lock);
 	do_timer(1);
 	write_sequnlock(&xtime_lock);

arch/arm/kernel/traps.c

@@ -12,15 +12,17 @@
  *  'linux/arch/arm/lib/traps.S'.  Mostly a debugging aid, but will probably
  *  kill the offending process.
  */
-#include <linux/module.h>
 #include <linux/signal.h>
-#include <linux/spinlock.h>
 #include <linux/personality.h>
 #include <linux/kallsyms.h>
-#include <linux/delay.h>
+#include <linux/spinlock.h>
-#include <linux/hardirq.h>
-#include <linux/init.h>
 #include <linux/uaccess.h>
+#include <linux/hardirq.h>
+#include <linux/kdebug.h>
+#include <linux/module.h>
+#include <linux/kexec.h>
+#include <linux/delay.h>
+#include <linux/init.h>
 
 #include <asm/atomic.h>
 #include <asm/cacheflush.h>
@@ -224,14 +226,21 @@ void show_stack(struct task_struct *tsk, unsigned long *sp)
 #define S_SMP ""
 #endif
 
-static void __die(const char *str, int err, struct thread_info *thread, struct pt_regs *regs)
+static int __die(const char *str, int err, struct thread_info *thread, struct pt_regs *regs)
 {
 	struct task_struct *tsk = thread->task;
 	static int die_counter;
+	int ret;
 
 	printk(KERN_EMERG "Internal error: %s: %x [#%d]" S_PREEMPT S_SMP "\n",
 	       str, err, ++die_counter);
 	sysfs_printk_last_file();
+
+	/* trap and error numbers are mostly meaningless on ARM */
+	ret = notify_die(DIE_OOPS, str, regs, err, tsk->thread.trap_no, SIGSEGV);
+	if (ret == NOTIFY_STOP)
+		return ret;
+
 	print_modules();
 	__show_regs(regs);
 	printk(KERN_EMERG "Process %.*s (pid: %d, stack limit = 0x%p)\n",
@@ -243,6 +252,8 @@ static void __die(const char *str, int err, struct thread_info *thread, struct p
 		dump_backtrace(regs, tsk);
 		dump_instr(KERN_EMERG, regs);
 	}
+
+	return ret;
 }
 
 DEFINE_SPINLOCK(die_lock);
@@ -250,16 +261,21 @@ DEFINE_SPINLOCK(die_lock);
 /*
  * This function is protected against re-entrancy.
  */
-NORET_TYPE void die(const char *str, struct pt_regs *regs, int err)
+void die(const char *str, struct pt_regs *regs, int err)
 {
 	struct thread_info *thread = current_thread_info();
+	int ret;
 
 	oops_enter();
 
 	spin_lock_irq(&die_lock);
 	console_verbose();
 	bust_spinlocks(1);
-	__die(str, err, thread, regs);
+	ret = __die(str, err, thread, regs);
+
+	if (regs && kexec_should_crash(thread->task))
+		crash_kexec(regs);
+
 	bust_spinlocks(0);
 	add_taint(TAINT_DIE);
 	spin_unlock_irq(&die_lock);
@@ -267,11 +283,10 @@ NORET_TYPE void die(const char *str, struct pt_regs *regs, int err)
 
 	if (in_interrupt())
 		panic("Fatal exception in interrupt");
-
 	if (panic_on_oops)
 		panic("Fatal exception");
-
+	if (ret != NOTIFY_STOP)
-	do_exit(SIGSEGV);
+		do_exit(SIGSEGV);
 }
 
 void arm_notify_die(const char *str, struct pt_regs *regs,

arch/arm/kernel/vmlinux.lds.S

@@ -43,10 +43,6 @@ SECTIONS
 
 		INIT_SETUP(16)
 
-		__early_begin = .;
-			*(.early_param.init)
-		__early_end = .;
-
 		INIT_CALLS
 		CON_INITCALL
 		SECURITY_INITCALL

arch/arm/mach-aaec2000/include/mach/debug-macro.S

@@ -10,7 +10,7 @@
  */
 
 #include "hardware.h"
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0x80000000		@ physical

arch/arm/mach-at91/Kconfig

@@ -89,6 +89,12 @@ config ARCH_AT91CAP9
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
 
+config ARCH_AT572D940HF
+	bool "AT572D940HF"
+	select CPU_ARM926T
+	select GENERIC_TIME
+	select GENERIC_CLOCKEVENTS
+
 config ARCH_AT91X40
 	bool "AT91x40"
 
@@ -390,6 +396,23 @@ endif
 
 # ----------------------------------------------------------
 
+if ARCH_AT572D940HF
+
+comment "AT572D940HF Board Type"
+
+config MACH_AT572D940HFEB
+	bool "AT572D940HF-EK"
+	depends on ARCH_AT572D940HF
+	select HAVE_AT91_DATAFLASH_CARD
+	select HAVE_NAND_ATMEL_BUSWIDTH_16
+	help
+	  Select this if you are using Atmel's AT572D940HF-EK evaluation kit.
+	  <http://www.atmel.com/products/diopsis/default.asp>
+
+endif
+
+# ----------------------------------------------------------
+
 if ARCH_AT91X40
 
 comment "AT91X40 Board Type"

arch/arm/mach-at91/Makefile

@@ -19,6 +19,7 @@ obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devi
 obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o  sam9_smc.o
  obj-$(CONFIG_ARCH_AT91SAM9G45)	+= at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91CAP9)	+= at91cap9.o at91sam926x_time.o at91cap9_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT572D940HF)  += at572d940hf.o at91sam926x_time.o at572d940hf_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o
 
 # AT91RM9200 board-specific support
@@ -69,6 +70,9 @@ obj-$(CONFIG_MACH_AT91SAM9G45EKES) += board-sam9m10g45ek.o
 # AT91CAP9 board-specific support
 obj-$(CONFIG_MACH_AT91CAP9ADK)	+= board-cap9adk.o
 
+# AT572D940HF board-specific support
+obj-$(CONFIG_MACH_AT572D940HFEB) += board-at572d940hf_ek.o
+
 # AT91X40 board-specific support
 obj-$(CONFIG_MACH_AT91EB01)	+= board-eb01.o
 

arch/arm/mach-at91/at572d940hf.c

@@ -0,0 +1,377 @@
+/*
+ * arch/arm/mach-at91/at572d940hf.c
+ *
+ * Antonio R. Costa <costa.antonior@gmail.com>
+ * Copyright (C) 2008 Atmel
+ *
+ * Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <mach/at572d940hf.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+
+#include "generic.h"
+#include "clock.h"
+
+static struct map_desc at572d940hf_io_desc[] __initdata = {
+	{
+		.virtual	= AT91_VA_BASE_SYS,
+		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
+		.length		= SZ_16K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT572D940HF_SRAM_SIZE,
+		.pfn		= __phys_to_pfn(AT572D940HF_SRAM_BASE),
+		.length		= AT572D940HF_SRAM_SIZE,
+		.type		= MT_DEVICE,
+	},
+};
+
+/* --------------------------------------------------------------------
+ *  Clocks
+ * -------------------------------------------------------------------- */
+
+/*
+ * The peripheral clocks.
+ */
+static struct clk pioA_clk = {
+	.name		= "pioA_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_PIOA,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioB_clk = {
+	.name		= "pioB_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_PIOB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioC_clk = {
+	.name		= "pioC_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_PIOC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk macb_clk = {
+	.name		= "macb_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_EMAC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart0_clk = {
+	.name		= "usart0_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_US0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart1_clk = {
+	.name		= "usart1_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_US1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart2_clk = {
+	.name		= "usart2_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_US2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc_clk = {
+	.name		= "mci_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_MCI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk udc_clk = {
+	.name		= "udc_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_UDP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi0_clk = {
+	.name		= "twi0_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_TWI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi0_clk = {
+	.name		= "spi0_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_SPI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi1_clk = {
+	.name		= "spi1_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_SPI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ssc0_clk = {
+	.name		= "ssc0_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_SSC0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ssc1_clk = {
+	.name		= "ssc1_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_SSC1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ssc2_clk = {
+	.name		= "ssc2_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_SSC2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc0_clk = {
+	.name		= "tc0_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_TC0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc1_clk = {
+	.name		= "tc1_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_TC1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc2_clk = {
+	.name		= "tc2_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_TC2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ohci_clk = {
+	.name		= "ohci_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_UHP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ssc3_clk = {
+	.name		= "ssc3_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_SSC3,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi1_clk = {
+	.name		= "twi1_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_TWI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk can0_clk = {
+	.name		= "can0_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_CAN0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk can1_clk = {
+	.name		= "can1_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_CAN1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mAgicV_clk = {
+	.name		= "mAgicV_clk",
+	.pmc_mask	= 1 << AT572D940HF_ID_MSIRQ0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+
+
+static struct clk *periph_clocks[] __initdata = {
+	&pioA_clk,
+	&pioB_clk,
+	&pioC_clk,
+	&macb_clk,
+	&usart0_clk,
+	&usart1_clk,
+	&usart2_clk,
+	&mmc_clk,
+	&udc_clk,
+	&twi0_clk,
+	&spi0_clk,
+	&spi1_clk,
+	&ssc0_clk,
+	&ssc1_clk,
+	&ssc2_clk,
+	&tc0_clk,
+	&tc1_clk,
+	&tc2_clk,
+	&ohci_clk,
+	&ssc3_clk,
+	&twi1_clk,
+	&can0_clk,
+	&can1_clk,
+	&mAgicV_clk,
+	/* irq0 .. irq2 */
+};
+
+/*
+ * The five programmable clocks.
+ * You must configure pin multiplexing to bring these signals out.
+ */
+static struct clk pck0 = {
+	.name		= "pck0",
+	.pmc_mask	= AT91_PMC_PCK0,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 0,
+};
+static struct clk pck1 = {
+	.name		= "pck1",
+	.pmc_mask	= AT91_PMC_PCK1,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 1,
+};
+static struct clk pck2 = {
+	.name		= "pck2",
+	.pmc_mask	= AT91_PMC_PCK2,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 2,
+};
+static struct clk pck3 = {
+	.name		= "pck3",
+	.pmc_mask	= AT91_PMC_PCK3,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 3,
+};
+
+static struct clk mAgicV_mem_clk = {
+	.name		= "mAgicV_mem_clk",
+	.pmc_mask	= AT91_PMC_PCK4,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 4,
+};
+
+/* HClocks */
+static struct clk hck0 = {
+	.name		= "hck0",
+	.pmc_mask	= AT91_PMC_HCK0,
+	.type		= CLK_TYPE_SYSTEM,
+	.id		= 0,
+};
+static struct clk hck1 = {
+	.name		= "hck1",
+	.pmc_mask	= AT91_PMC_HCK1,
+	.type		= CLK_TYPE_SYSTEM,
+	.id		= 1,
+};
+
+static void __init at572d940hf_register_clocks(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
+		clk_register(periph_clocks[i]);
+
+	clk_register(&pck0);
+	clk_register(&pck1);
+	clk_register(&pck2);
+	clk_register(&pck3);
+	clk_register(&mAgicV_mem_clk);
+
+	clk_register(&hck0);
+	clk_register(&hck1);
+}
+
+/* --------------------------------------------------------------------
+ *  GPIO
+ * -------------------------------------------------------------------- */
+
+static struct at91_gpio_bank at572d940hf_gpio[] = {
+	{
+		.id		= AT572D940HF_ID_PIOA,
+		.offset		= AT91_PIOA,
+		.clock		= &pioA_clk,
+	}, {
+		.id		= AT572D940HF_ID_PIOB,
+		.offset		= AT91_PIOB,
+		.clock		= &pioB_clk,
+	}, {
+		.id		= AT572D940HF_ID_PIOC,
+		.offset		= AT91_PIOC,
+		.clock		= &pioC_clk,
+	}
+};
+
+static void at572d940hf_reset(void)
+{
+	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
+}
+
+
+/* --------------------------------------------------------------------
+ *  AT572D940HF processor initialization
+ * -------------------------------------------------------------------- */
+
+void __init at572d940hf_initialize(unsigned long main_clock)
+{
+	/* Map peripherals */
+	iotable_init(at572d940hf_io_desc, ARRAY_SIZE(at572d940hf_io_desc));
+
+	at91_arch_reset = at572d940hf_reset;
+	at91_extern_irq = (1 << AT572D940HF_ID_IRQ0) | (1 << AT572D940HF_ID_IRQ1)
+			| (1 << AT572D940HF_ID_IRQ2);
+
+	/* Init clock subsystem */
+	at91_clock_init(main_clock);
+
+	/* Register the processor-specific clocks */
+	at572d940hf_register_clocks();
+
+	/* Register GPIO subsystem */
+	at91_gpio_init(at572d940hf_gpio, 3);
+}
+
+/* --------------------------------------------------------------------
+ *  Interrupt initialization
+ * -------------------------------------------------------------------- */
+
+/*
+ * The default interrupt priority levels (0 = lowest, 7 = highest).
+ */
+static unsigned int at572d940hf_default_irq_priority[NR_AIC_IRQS] __initdata = {
+	7,	/* Advanced Interrupt Controller */
+	7,	/* System Peripherals */
+	0,	/* Parallel IO Controller A */
+	0,	/* Parallel IO Controller B */
+	0,	/* Parallel IO Controller C */
+	3,	/* Ethernet */
+	6,	/* USART 0 */
+	6,	/* USART 1 */
+	6,	/* USART 2 */
+	0,	/* Multimedia Card Interface */
+	4,	/* USB Device Port */
+	0,	/* Two-Wire Interface 0 */
+	6,	/* Serial Peripheral Interface 0 */
+	6,	/* Serial Peripheral Interface 1 */
+	5,	/* Serial Synchronous Controller 0 */
+	5,	/* Serial Synchronous Controller 1 */
+	5,	/* Serial Synchronous Controller 2 */
+	0,	/* Timer Counter 0 */
+	0,	/* Timer Counter 1 */
+	0,	/* Timer Counter 2 */
+	3,	/* USB Host port */
+	3,	/* Serial Synchronous Controller 3 */
+	0,	/* Two-Wire Interface 1 */
+	0,	/* CAN Controller 0 */
+	0,	/* CAN Controller 1 */
+	0,	/* mAgicV HALT line */
+	0,	/* mAgicV SIRQ0 line */
+	0,	/* mAgicV exception line */
+	0,	/* mAgicV end of DMA line */
+	0,	/* Advanced Interrupt Controller */
+	0,	/* Advanced Interrupt Controller */
+	0,	/* Advanced Interrupt Controller */
+};
+
+void __init at572d940hf_init_interrupts(unsigned int priority[NR_AIC_IRQS])
+{
+	if (!priority)
+		priority = at572d940hf_default_irq_priority;
+
+	/* Initialize the AIC interrupt controller */
+	at91_aic_init(priority);
+
+	/* Enable GPIO interrupts */
+	at91_gpio_irq_setup();
+}
+

arch/arm/mach-at91/at572d940hf_devices.c

@@ -0,0 +1,970 @@
+/*
+ * arch/arm/mach-at91/at572d940hf_devices.c
+ *
+ * Copyright (C) 2008 Atmel Antonio R. Costa <costa.antonior@gmail.com>
+ * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ * Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at572d940hf.h>
+#include <mach/at572d940hf_matrix.h>
+#include <mach/at91sam9_smc.h>
+
+#include "generic.h"
+#include "sam9_smc.h"
+
+
+/* --------------------------------------------------------------------
+ *  USB Host
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+static u64 ohci_dmamask = DMA_BIT_MASK(32);
+static struct at91_usbh_data usbh_data;
+
+static struct resource usbh_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_UHP_BASE,
+		.end	= AT572D940HF_UHP_BASE + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_UHP,
+		.end	= AT572D940HF_ID_UHP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_usbh_device = {
+	.name		= "at91_ohci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &ohci_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &usbh_data,
+	},
+	.resource	= usbh_resources,
+	.num_resources	= ARRAY_SIZE(usbh_resources),
+};
+
+void __init at91_add_device_usbh(struct at91_usbh_data *data)
+{
+	if (!data)
+		return;
+
+	usbh_data = *data;
+	platform_device_register(&at572d940hf_usbh_device);
+
+}
+#else
+void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  USB Device (Gadget)
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_USB_GADGET_AT91
+static struct at91_udc_data udc_data;
+
+static struct resource udc_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_UDP,
+		.end	= AT572D940HF_BASE_UDP + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_UDP,
+		.end	= AT572D940HF_ID_UDP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_udc_device = {
+	.name		= "at91_udc",
+	.id		= -1,
+	.dev		= {
+				.platform_data		= &udc_data,
+	},
+	.resource	= udc_resources,
+	.num_resources	= ARRAY_SIZE(udc_resources),
+};
+
+void __init at91_add_device_udc(struct at91_udc_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->vbus_pin) {
+		at91_set_gpio_input(data->vbus_pin, 0);
+		at91_set_deglitch(data->vbus_pin, 1);
+	}
+
+	/* Pullup pin is handled internally */
+
+	udc_data = *data;
+	platform_device_register(&at572d940hf_udc_device);
+}
+#else
+void __init at91_add_device_udc(struct at91_udc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Ethernet
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
+static u64 eth_dmamask = DMA_BIT_MASK(32);
+static struct at91_eth_data eth_data;
+
+static struct resource eth_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_EMAC,
+		.end	= AT572D940HF_BASE_EMAC + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_EMAC,
+		.end	= AT572D940HF_ID_EMAC,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_eth_device = {
+	.name		= "macb",
+	.id		= -1,
+	.dev		= {
+			.dma_mask		= &eth_dmamask,
+			.coherent_dma_mask	= DMA_BIT_MASK(32),
+			.platform_data		= &eth_data,
+	},
+	.resource	= eth_resources,
+	.num_resources	= ARRAY_SIZE(eth_resources),
+};
+
+void __init at91_add_device_eth(struct at91_eth_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->phy_irq_pin) {
+		at91_set_gpio_input(data->phy_irq_pin, 0);
+		at91_set_deglitch(data->phy_irq_pin, 1);
+	}
+
+	/* Only RMII is supported */
+	data->is_rmii = 1;
+
+	/* Pins used for RMII */
+	at91_set_A_periph(AT91_PIN_PA16, 0);	/* ETXCK_EREFCK */
+	at91_set_A_periph(AT91_PIN_PA17, 0);	/* ERXDV */
+	at91_set_A_periph(AT91_PIN_PA18, 0);	/* ERX0 */
+	at91_set_A_periph(AT91_PIN_PA19, 0);	/* ERX1 */
+	at91_set_A_periph(AT91_PIN_PA20, 0);	/* ERXER */
+	at91_set_A_periph(AT91_PIN_PA23, 0);	/* ETXEN */
+	at91_set_A_periph(AT91_PIN_PA21, 0);	/* ETX0 */
+	at91_set_A_periph(AT91_PIN_PA22, 0);	/* ETX1 */
+	at91_set_A_periph(AT91_PIN_PA13, 0);	/* EMDIO */
+	at91_set_A_periph(AT91_PIN_PA14, 0);	/* EMDC */
+
+	eth_data = *data;
+	platform_device_register(&at572d940hf_eth_device);
+}
+#else
+void __init at91_add_device_eth(struct at91_eth_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  MMC / SD
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+static u64 mmc_dmamask = DMA_BIT_MASK(32);
+static struct at91_mmc_data mmc_data;
+
+static struct resource mmc_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_MCI,
+		.end	= AT572D940HF_BASE_MCI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_MCI,
+		.end	= AT572D940HF_ID_MCI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_mmc_device = {
+	.name		= "at91_mci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &mmc_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &mmc_data,
+	},
+	.resource	= mmc_resources,
+	.num_resources	= ARRAY_SIZE(mmc_resources),
+};
+
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
+{
+	if (!data)
+		return;
+
+	/* input/irq */
+	if (data->det_pin) {
+		at91_set_gpio_input(data->det_pin, 1);
+		at91_set_deglitch(data->det_pin, 1);
+	}
+	if (data->wp_pin)
+		at91_set_gpio_input(data->wp_pin, 1);
+	if (data->vcc_pin)
+		at91_set_gpio_output(data->vcc_pin, 0);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PC22, 0);
+
+	/* CMD */
+	at91_set_A_periph(AT91_PIN_PC23, 1);
+
+	/* DAT0, maybe DAT1..DAT3 */
+	at91_set_A_periph(AT91_PIN_PC24, 1);
+	if (data->wire4) {
+		at91_set_A_periph(AT91_PIN_PC25, 1);
+		at91_set_A_periph(AT91_PIN_PC26, 1);
+		at91_set_A_periph(AT91_PIN_PC27, 1);
+	}
+
+	mmc_data = *data;
+	platform_device_register(&at572d940hf_mmc_device);
+}
+#else
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
+static struct atmel_nand_data nand_data;
+
+#define NAND_BASE	AT91_CHIPSELECT_3
+
+static struct resource nand_resources[] = {
+	{
+		.start	= NAND_BASE,
+		.end	= NAND_BASE + SZ_256M - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at572d940hf_nand_device = {
+	.name		= "atmel_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= nand_resources,
+	.num_resources	= ARRAY_SIZE(nand_resources),
+};
+
+void __init at91_add_device_nand(struct atmel_nand_data *data)
+{
+	unsigned long csa;
+
+	if (!data)
+		return;
+
+	csa = at91_sys_read(AT91_MATRIX_EBICSA);
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
+
+	/* enable pin */
+	if (data->enable_pin)
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (data->rdy_pin)
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (data->det_pin)
+		at91_set_gpio_input(data->det_pin, 1);
+
+	at91_set_A_periph(AT91_PIN_PB28, 0);		/* A[22] */
+	at91_set_B_periph(AT91_PIN_PA28, 0);		/* NANDOE */
+	at91_set_B_periph(AT91_PIN_PA29, 0);		/* NANDWE */
+
+	nand_data = *data;
+	platform_device_register(&at572d940hf_nand_device);
+}
+
+#else
+void __init at91_add_device_nand(struct atmel_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+/*
+ * Prefer the GPIO code since the TWI controller isn't robust
+ * (gets overruns and underruns under load) and can only issue
+ * repeated STARTs in one scenario (the driver doesn't yet handle them).
+ */
+
+#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+
+static struct i2c_gpio_platform_data pdata = {
+	.sda_pin		= AT91_PIN_PC7,
+	.sda_is_open_drain	= 1,
+	.scl_pin		= AT91_PIN_PC8,
+	.scl_is_open_drain	= 1,
+	.udelay			= 2,		/* ~100 kHz */
+};
+
+static struct platform_device at572d940hf_twi_device {
+	.name			= "i2c-gpio",
+	.id			= -1,
+	.dev.platform_data	= &pdata,
+};
+
+void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
+{
+	at91_set_GPIO_periph(AT91_PIN_PC7, 1);		/* TWD (SDA) */
+	at91_set_multi_drive(AT91_PIN_PC7, 1);
+
+	at91_set_GPIO_periph(AT91_PIN_PA8, 1);		/* TWCK (SCL) */
+	at91_set_multi_drive(AT91_PIN_PC8, 1);
+
+	i2c_register_board_info(0, devices, nr_devices);
+	platform_device_register(&at572d940hf_twi_device);
+}
+
+#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+
+static struct resource twi0_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_TWI0,
+		.end	= AT572D940HF_BASE_TWI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_TWI0,
+		.end	= AT572D940HF_ID_TWI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_twi0_device = {
+	.name		= "at91_i2c",
+	.id		= 0,
+	.resource	= twi0_resources,
+	.num_resources	= ARRAY_SIZE(twi0_resources),
+};
+
+static struct resource twi1_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_TWI1,
+		.end	= AT572D940HF_BASE_TWI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_TWI1,
+		.end	= AT572D940HF_ID_TWI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_twi1_device = {
+	.name		= "at91_i2c",
+	.id		= 1,
+	.resource	= twi1_resources,
+	.num_resources	= ARRAY_SIZE(twi1_resources),
+};
+
+void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
+{
+	/* pins used for TWI0 interface */
+	at91_set_A_periph(AT91_PIN_PC7, 0);		/* TWD */
+	at91_set_multi_drive(AT91_PIN_PC7, 1);
+
+	at91_set_A_periph(AT91_PIN_PC8, 0);		/* TWCK */
+	at91_set_multi_drive(AT91_PIN_PC8, 1);
+
+	/* pins used for TWI1 interface */
+	at91_set_A_periph(AT91_PIN_PC20, 0);		/* TWD */
+	at91_set_multi_drive(AT91_PIN_PC20, 1);
+
+	at91_set_A_periph(AT91_PIN_PC21, 0);		/* TWCK */
+	at91_set_multi_drive(AT91_PIN_PC21, 1);
+
+	i2c_register_board_info(0, devices, nr_devices);
+	platform_device_register(&at572d940hf_twi0_device);
+	platform_device_register(&at572d940hf_twi1_device);
+}
+#else
+void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+static u64 spi_dmamask = DMA_BIT_MASK(32);
+
+static struct resource spi0_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_SPI0,
+		.end	= AT572D940HF_BASE_SPI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_SPI0,
+		.end	= AT572D940HF_ID_SPI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_spi0_device = {
+	.name		= "atmel_spi",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= spi0_resources,
+	.num_resources	= ARRAY_SIZE(spi0_resources),
+};
+
+static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
+
+static struct resource spi1_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_SPI1,
+		.end	= AT572D940HF_BASE_SPI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_SPI1,
+		.end	= AT572D940HF_ID_SPI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_spi1_device = {
+	.name		= "atmel_spi",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= spi1_resources,
+	.num_resources	= ARRAY_SIZE(spi1_resources),
+};
+
+static const unsigned spi1_standard_cs[4] = { AT91_PIN_PC3, AT91_PIN_PC4, AT91_PIN_PC5, AT91_PIN_PC6 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+	int i;
+	unsigned long cs_pin;
+	short enable_spi0 = 0;
+	short enable_spi1 = 0;
+
+	/* Choose SPI chip-selects */
+	for (i = 0; i < nr_devices; i++) {
+		if (devices[i].controller_data)
+			cs_pin = (unsigned long) devices[i].controller_data;
+		else if (devices[i].bus_num == 0)
+			cs_pin = spi0_standard_cs[devices[i].chip_select];
+		else
+			cs_pin = spi1_standard_cs[devices[i].chip_select];
+
+		if (devices[i].bus_num == 0)
+			enable_spi0 = 1;
+		else
+			enable_spi1 = 1;
+
+		/* enable chip-select pin */
+		at91_set_gpio_output(cs_pin, 1);
+
+		/* pass chip-select pin to driver */
+		devices[i].controller_data = (void *) cs_pin;
+	}
+
+	spi_register_board_info(devices, nr_devices);
+
+	/* Configure SPI bus(es) */
+	if (enable_spi0) {
+		at91_set_A_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
+		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
+		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
+
+		at91_clock_associate("spi0_clk", &at572d940hf_spi0_device.dev, "spi_clk");
+		platform_device_register(&at572d940hf_spi0_device);
+	}
+	if (enable_spi1) {
+		at91_set_A_periph(AT91_PIN_PC0, 0);	/* SPI1_MISO */
+		at91_set_A_periph(AT91_PIN_PC1, 0);	/* SPI1_MOSI */
+		at91_set_A_periph(AT91_PIN_PC2, 0);	/* SPI1_SPCK */
+
+		at91_clock_associate("spi1_clk", &at572d940hf_spi1_device.dev, "spi_clk");
+		platform_device_register(&at572d940hf_spi1_device);
+	}
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Timer/Counter blocks
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_ATMEL_TCLIB
+
+static struct resource tcb_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_TCB,
+		.end	= AT572D940HF_BASE_TCB + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_TC0,
+		.end	= AT572D940HF_ID_TC0,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AT572D940HF_ID_TC1,
+		.end	= AT572D940HF_ID_TC1,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[3] = {
+		.start	= AT572D940HF_ID_TC2,
+		.end	= AT572D940HF_ID_TC2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at572d940hf_tcb_device = {
+	.name		= "atmel_tcb",
+	.id		= 0,
+	.resource	= tcb_resources,
+	.num_resources	= ARRAY_SIZE(tcb_resources),
+};
+
+static void __init at91_add_device_tc(void)
+{
+	/* this chip has a separate clock and irq for each TC channel */
+	at91_clock_associate("tc0_clk", &at572d940hf_tcb_device.dev, "t0_clk");
+	at91_clock_associate("tc1_clk", &at572d940hf_tcb_device.dev, "t1_clk");
+	at91_clock_associate("tc2_clk", &at572d940hf_tcb_device.dev, "t2_clk");
+	platform_device_register(&at572d940hf_tcb_device);
+}
+#else
+static void __init at91_add_device_tc(void) { }
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  RTT
+ * -------------------------------------------------------------------- */
+
+static struct resource rtt_resources[] = {
+	{
+		.start	= AT91_BASE_SYS + AT91_RTT,
+		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at572d940hf_rtt_device = {
+	.name		= "at91_rtt",
+	.id		= 0,
+	.resource	= rtt_resources,
+	.num_resources	= ARRAY_SIZE(rtt_resources),
+};
+
+static void __init at91_add_device_rtt(void)
+{
+	platform_device_register(&at572d940hf_rtt_device);
+}
+
+
+/* --------------------------------------------------------------------
+ *  Watchdog
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct platform_device at572d940hf_wdt_device = {
+	.name		= "at91_wdt",
+	.id		= -1,
+	.num_resources	= 0,
+};
+
+static void __init at91_add_device_watchdog(void)
+{
+	platform_device_register(&at572d940hf_wdt_device);
+}
+#else
+static void __init at91_add_device_watchdog(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  UART
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SERIAL_ATMEL)
+static struct resource dbgu_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
+		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data dbgu_data = {
+	.use_dma_tx	= 0,
+	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
+};
+
+static u64 dbgu_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at572d940hf_dbgu_device = {
+	.name		= "atmel_usart",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &dbgu_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &dbgu_data,
+	},
+	.resource	= dbgu_resources,
+	.num_resources	= ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PC31, 1);		/* DTXD */
+	at91_set_A_periph(AT91_PIN_PC30, 0);		/* DRXD */
+}
+
+static struct resource uart0_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_US0,
+		.end	= AT572D940HF_BASE_US0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_US0,
+		.end	= AT572D940HF_ID_US0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart0_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static u64 uart0_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at572d940hf_uart0_device = {
+	.name		= "atmel_usart",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &uart0_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &uart0_data,
+	},
+	.resource	= uart0_resources,
+	.num_resources	= ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(unsigned pins)
+{
+	at91_set_A_periph(AT91_PIN_PA8, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PA7, 0);		/* RXD0 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_A_periph(AT91_PIN_PA10, 0);	/* RTS0 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_A_periph(AT91_PIN_PA9, 0);	/* CTS0 */
+}
+
+static struct resource uart1_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_US1,
+		.end	= AT572D940HF_BASE_US1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_US1,
+		.end	= AT572D940HF_ID_US1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart1_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static u64 uart1_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at572d940hf_uart1_device = {
+	.name		= "atmel_usart",
+	.id		= 2,
+	.dev		= {
+				.dma_mask		= &uart1_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &uart1_data,
+	},
+	.resource	= uart1_resources,
+	.num_resources	= ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(unsigned pins)
+{
+	at91_set_A_periph(AT91_PIN_PC10, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PC9 , 0);		/* RXD1 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_A_periph(AT91_PIN_PC12, 0);	/* RTS1 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_A_periph(AT91_PIN_PC11, 0);	/* CTS1 */
+}
+
+static struct resource uart2_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_BASE_US2,
+		.end	= AT572D940HF_BASE_US2 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT572D940HF_ID_US2,
+		.end	= AT572D940HF_ID_US2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart2_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static u64 uart2_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device at572d940hf_uart2_device = {
+	.name		= "atmel_usart",
+	.id		= 3,
+	.dev		= {
+				.dma_mask		= &uart2_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &uart2_data,
+	},
+	.resource	= uart2_resources,
+	.num_resources	= ARRAY_SIZE(uart2_resources),
+};
+
+static inline void configure_usart2_pins(unsigned pins)
+{
+	at91_set_A_periph(AT91_PIN_PC15, 1);		/* TXD2 */
+	at91_set_A_periph(AT91_PIN_PC14, 0);		/* RXD2 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_A_periph(AT91_PIN_PC17, 0);	/* RTS2 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_A_periph(AT91_PIN_PC16, 0);	/* CTS2 */
+}
+
+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
+struct platform_device *atmel_default_console_device;	/* the serial console device */
+
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	switch (id) {
+		case 0:		/* DBGU */
+			pdev = &at572d940hf_dbgu_device;
+			configure_dbgu_pins();
+			at91_clock_associate("mck", &pdev->dev, "usart");
+			break;
+		case AT572D940HF_ID_US0:
+			pdev = &at572d940hf_uart0_device;
+			configure_usart0_pins(pins);
+			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+			break;
+		case AT572D940HF_ID_US1:
+			pdev = &at572d940hf_uart1_device;
+			configure_usart1_pins(pins);
+			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+			break;
+		case AT572D940HF_ID_US2:
+			pdev = &at572d940hf_uart2_device;
+			configure_usart2_pins(pins);
+			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+			break;
+		default:
+			return;
+	}
+	pdev->id = portnr;		/* update to mapped ID */
+
+	if (portnr < ATMEL_MAX_UART)
+		at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+	if (portnr < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[portnr];
+}
+
+void __init at91_add_device_serial(void)
+{
+	int i;
+
+	for (i = 0; i < ATMEL_MAX_UART; i++) {
+		if (at91_uarts[i])
+			platform_device_register(at91_uarts[i]);
+	}
+
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
+#else
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
+void __init at91_add_device_serial(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  mAgic
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_MAGICV
+static struct resource mAgic_resources[] = {
+	{
+		.start = AT91_MAGIC_PM_BASE,
+		.end   = AT91_MAGIC_PM_BASE + AT91_MAGIC_PM_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = AT91_MAGIC_DM_I_BASE,
+		.end   = AT91_MAGIC_DM_I_BASE + AT91_MAGIC_DM_I_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = AT91_MAGIC_DM_F_BASE,
+		.end   = AT91_MAGIC_DM_F_BASE + AT91_MAGIC_DM_F_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = AT91_MAGIC_DM_DB_BASE,
+		.end   = AT91_MAGIC_DM_DB_BASE + AT91_MAGIC_DM_DB_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = AT91_MAGIC_REGS_BASE,
+		.end   = AT91_MAGIC_REGS_BASE + AT91_MAGIC_REGS_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = AT91_MAGIC_EXTPAGE_BASE,
+		.end   = AT91_MAGIC_EXTPAGE_BASE + AT91_MAGIC_EXTPAGE_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start  = AT572D940HF_ID_MSIRQ0,
+		.end    = AT572D940HF_ID_MSIRQ0,
+		.flags  = IORESOURCE_IRQ,
+	},
+	{
+		.start  = AT572D940HF_ID_MHALT,
+		.end    = AT572D940HF_ID_MHALT,
+		.flags  = IORESOURCE_IRQ,
+	},
+	{
+		.start  = AT572D940HF_ID_MEXC,
+		.end    = AT572D940HF_ID_MEXC,
+		.flags  = IORESOURCE_IRQ,
+	},
+	{
+		.start  = AT572D940HF_ID_MEDMA,
+		.end    = AT572D940HF_ID_MEDMA,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device mAgic_device = {
+	.name           = "mAgic",
+	.id             = -1,
+	.num_resources  = ARRAY_SIZE(mAgic_resources),
+	.resource       = mAgic_resources,
+};
+
+void __init at91_add_device_mAgic(void)
+{
+	platform_device_register(&mAgic_device);
+}
+#else
+void __init at91_add_device_mAgic(void) {}
+#endif
+
+
+/* -------------------------------------------------------------------- */
+
+/*
+ * These devices are always present and don't need any board-specific
+ * setup.
+ */
+static int __init at91_add_standard_devices(void)
+{
+	at91_add_device_rtt();
+	at91_add_device_watchdog();
+	at91_add_device_tc();
+	return 0;
+}
+
+arch_initcall(at91_add_standard_devices);

arch/arm/mach-at91/board-at572d940hf_ek.c

@@ -0,0 +1,328 @@
+/*
+ * linux/arch/arm/mach-at91/board-at572d940hf_ek.c
+ *
+ * Copyright (C) 2008 Atmel Antonio R. Costa <costa.antonior@gmail.com>
+ * Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ds1305.h>
+#include <linux/irq.h>
+#include <linux/mtd/physmap.h>
+
+#include <mach/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init eb_map_io(void)
+{
+	/* Initialize processor: 12.500 MHz crystal */
+	at572d940hf_initialize(12000000);
+
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx & Tx only) */
+	at91_register_uart(AT572D940HF_ID_US0, 1, 0);
+
+	/* USART1 on ttyS2. (Rx & Tx only) */
+	at91_register_uart(AT572D940HF_ID_US1, 2, 0);
+
+	/* USART2 on ttyS3. (Tx & Rx only */
+	at91_register_uart(AT572D940HF_ID_US2, 3, 0);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init eb_init_irq(void)
+{
+	at572d940hf_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host Port
+ */
+static struct at91_usbh_data __initdata eb_usbh_data = {
+	.ports		= 2,
+};
+
+
+/*
+ * USB Device Port
+ */
+static struct at91_udc_data __initdata eb_udc_data = {
+	.vbus_pin	= 0,		/* no VBUS detection,UDC always on */
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata eb_mmc_data = {
+	.wire4		= 1,
+/*	.det_pin	= ... not connected */
+/*	.wp_pin		= ... not connected */
+/*	.vcc_pin	= ... not connected */
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata eb_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PB25,
+	.is_rmii	= 1,
+};
+
+/*
+ * NOR flash
+ */
+
+static struct mtd_partition eb_nor_partitions[] = {
+	{
+		.name		= "Raw Environment",
+		.offset		= 0,
+		.size		= SZ_4M,
+		.mask_flags	= 0,
+	},
+	{
+		.name		= "OS FS",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 3 * SZ_1M,
+		.mask_flags	= 0,
+	},
+	{
+		.name		= "APP FS",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= 0,
+	},
+};
+
+static void nor_flash_set_vpp(struct map_info* mi, int i) {
+};
+
+static struct physmap_flash_data nor_flash_data = {
+	.width		= 4,
+	.parts		= eb_nor_partitions,
+	.nr_parts	= ARRAY_SIZE(eb_nor_partitions),
+	.set_vpp	= nor_flash_set_vpp,
+};
+
+static struct resource nor_flash_resources[] = {
+	{
+		.start	= AT91_CHIPSELECT_0,
+		.end	= AT91_CHIPSELECT_0 + SZ_16M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device nor_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+				.platform_data = &nor_flash_data,
+			},
+	.resource	= nor_flash_resources,
+	.num_resources	= ARRAY_SIZE(nor_flash_resources),
+};
+
+static struct sam9_smc_config __initdata eb_nor_smc_config = {
+	.ncs_read_setup		= 1,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 1,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 7,
+	.nrd_pulse		= 7,
+	.ncs_write_pulse	= 7,
+	.nwe_pulse		= 7,
+
+	.read_cycle		= 9,
+	.write_cycle		= 9,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_32,
+	.tdf_cycles		= 1,
+};
+
+static void __init eb_add_device_nor(void)
+{
+	/* configure chip-select 0 (NOR) */
+	sam9_smc_configure(0, &eb_nor_smc_config);
+	platform_device_register(&nor_flash);
+}
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata eb_nand_partition[] = {
+	{
+		.name	= "Partition 1",
+		.offset	= 0,
+		.size	= SZ_16M,
+	},
+	{
+		.name	= "Partition 2",
+		.offset = MTDPART_OFS_NXTBLK,
+		.size	= MTDPART_SIZ_FULL,
+	}
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(eb_nand_partition);
+	return eb_nand_partition;
+}
+
+static struct atmel_nand_data __initdata eb_nand_data = {
+	.ale		= 22,
+	.cle		= 21,
+/*	.det_pin	= ... not connected */
+/*	.rdy_pin	= AT91_PIN_PC16, */
+	.enable_pin	= AT91_PIN_PA15,
+	.partition_info	= nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+};
+
+static struct sam9_smc_config __initdata eb_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 0,
+	.ncs_write_setup	= 1,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 12,
+};
+
+static void __init eb_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (eb_nand_data.bus_width_16)
+		eb_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		eb_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &eb_nand_smc_config);
+
+	at91_add_device_nand(&eb_nand_data);
+}
+
+
+/*
+ * SPI devices
+ */
+static struct resource rtc_resources[] = {
+	[0] = {
+		.start	= AT572D940HF_ID_IRQ1,
+		.end	= AT572D940HF_ID_IRQ1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct ds1305_platform_data ds1306_data = {
+	.is_ds1306	= true,
+	.en_1hz		= false,
+};
+
+static struct spi_board_info eb_spi_devices[] = {
+	{	/* RTC Dallas DS1306 */
+		.modalias	= "rtc-ds1305",
+		.chip_select	= 3,
+		.mode		= SPI_CS_HIGH | SPI_CPOL | SPI_CPHA,
+		.max_speed_hz	= 500000,
+		.bus_num	= 0,
+		.irq		= AT572D940HF_ID_IRQ1,
+		.platform_data	= (void *) &ds1306_data,
+	},
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* Dataflash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+};
+
+static void __init eb_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB Host */
+	at91_add_device_usbh(&eb_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&eb_udc_data);
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
+	/* NOR */
+	eb_add_device_nor();
+	/* NAND */
+	eb_add_device_nand();
+	/* SPI */
+	at91_add_device_spi(eb_spi_devices, ARRAY_SIZE(eb_spi_devices));
+	/* MMC */
+	at91_add_device_mmc(0, &eb_mmc_data);
+	/* Ethernet */
+	at91_add_device_eth(&eb_eth_data);
+	/* mAgic */
+	at91_add_device_mAgic();
+}
+
+MACHINE_START(AT572D940HFEB, "Atmel AT91D940HF-EB")
+	/* Maintainer: Atmel <costa.antonior@gmail.com> */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= eb_map_io,
+	.init_irq	= eb_init_irq,
+	.init_machine	= eb_board_init,
+MACHINE_END

arch/arm/mach-at91/clock.c

@@ -29,6 +29,7 @@
 #include <mach/cpu.h>
 
 #include "clock.h"
+#include "generic.h"
 
 
 /*
@@ -628,7 +629,7 @@ static void __init at91_pllb_usbfs_clock_init(unsigned long main_clock)
 		at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
 	} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() ||
 		   cpu_is_at91sam9263() || cpu_is_at91sam9g20() ||
-		   cpu_is_at91sam9g10()) {
+		   cpu_is_at91sam9g10() || cpu_is_at572d940hf()) {
 		uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
 		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
 	} else if (cpu_is_at91cap9()) {
@@ -711,12 +712,13 @@ int __init at91_clock_init(unsigned long main_clock)
 	/*
 	 * USB HS clock init
 	 */
-	if (cpu_has_utmi())
+	if (cpu_has_utmi()) {
 		/*
 		 * multiplier is hard-wired to 40
 		 * (obtain the USB High Speed 480 MHz when input is 12 MHz)
 		 */
 		utmi_clk.rate_hz = 40 * utmi_clk.parent->rate_hz;
+	}
 
 	/*
 	 * USB FS clock init
@@ -746,7 +748,7 @@ int __init at91_clock_init(unsigned long main_clock)
 		mck.rate_hz = (mckr & AT91_PMC_MDIV) == AT91SAM9_PMC_MDIV_3 ?
 			freq / 3 : freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));	/* mdiv */
 	} else {
-		mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));      /* mdiv */
+		mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));		/* mdiv */
 	}
 
 	/* Register the PMC's standard clocks */

arch/arm/mach-at91/clock.h

@@ -22,7 +22,7 @@ struct clk {
 	struct clk	*parent;
 	u32		pmc_mask;
 	void		(*mode)(struct clk *, int);
-	unsigned	id:2;		/* PCK0..3, or 32k/main/a/b */
+	unsigned	id:3;		/* PCK0..4, or 32k/main/a/b */
 	unsigned	type;		/* clock type */
 	u16		users;
 };

arch/arm/mach-at91/generic.h

@@ -17,6 +17,7 @@ extern void __init at91sam9rl_initialize(unsigned long main_clock);
 extern void __init at91sam9g45_initialize(unsigned long main_clock);
 extern void __init at91x40_initialize(unsigned long main_clock);
 extern void __init at91cap9_initialize(unsigned long main_clock);
+extern void __init at572d940hf_initialize(unsigned long main_clock);
 
  /* Interrupts */
 extern void __init at91rm9200_init_interrupts(unsigned int priority[]);
@@ -27,6 +28,7 @@ extern void __init at91sam9rl_init_interrupts(unsigned int priority[]);
 extern void __init at91sam9g45_init_interrupts(unsigned int priority[]);
 extern void __init at91x40_init_interrupts(unsigned int priority[]);
 extern void __init at91cap9_init_interrupts(unsigned int priority[]);
+extern void __init at572d940hf_init_interrupts(unsigned int priority[]);
 extern void __init at91_aic_init(unsigned int priority[]);
 
  /* Timer */

arch/arm/mach-at91/include/mach/at572d940hf.h

@@ -0,0 +1,123 @@
+/*
+ * include/mach/at572d940hf.h
+ *
+ * Antonio R. Costa <costa.antonior@gmail.com>
+ * Copyright (C) 2008 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#ifndef AT572D940HF_H
+#define AT572D940HF_H
+
+/*
+ * Peripheral identifiers/interrupts.
+ */
+#define AT91_ID_FIQ		0	/* Advanced Interrupt Controller (FIQ) */
+#define AT91_ID_SYS		1	/* System Peripherals */
+#define AT572D940HF_ID_PIOA	2	/* Parallel IO Controller A */
+#define AT572D940HF_ID_PIOB	3	/* Parallel IO Controller B */
+#define AT572D940HF_ID_PIOC	4	/* Parallel IO Controller C */
+#define AT572D940HF_ID_EMAC	5	/* MACB ethernet controller */
+#define AT572D940HF_ID_US0	6	/* USART 0 */
+#define AT572D940HF_ID_US1	7	/* USART 1 */
+#define AT572D940HF_ID_US2	8	/* USART 2 */
+#define AT572D940HF_ID_MCI	9	/* Multimedia Card Interface */
+#define AT572D940HF_ID_UDP	10	/* USB Device Port */
+#define AT572D940HF_ID_TWI0	11	/* Two-Wire Interface 0 */
+#define AT572D940HF_ID_SPI0	12	/* Serial Peripheral Interface 0 */
+#define AT572D940HF_ID_SPI1	13	/* Serial Peripheral Interface 1 */
+#define AT572D940HF_ID_SSC0	14	/* Serial Synchronous Controller 0 */
+#define AT572D940HF_ID_SSC1	15	/* Serial Synchronous Controller 1 */
+#define AT572D940HF_ID_SSC2	16	/* Serial Synchronous Controller 2 */
+#define AT572D940HF_ID_TC0	17	/* Timer Counter 0 */
+#define AT572D940HF_ID_TC1	18	/* Timer Counter 1 */
+#define AT572D940HF_ID_TC2	19	/* Timer Counter 2 */
+#define AT572D940HF_ID_UHP	20	/* USB Host port */
+#define AT572D940HF_ID_SSC3	21	/* Serial Synchronous Controller 3 */
+#define AT572D940HF_ID_TWI1	22	/* Two-Wire Interface 1 */
+#define AT572D940HF_ID_CAN0	23	/* CAN Controller 0 */
+#define AT572D940HF_ID_CAN1	24	/* CAN Controller 1 */
+#define AT572D940HF_ID_MHALT	25	/* mAgicV HALT line */
+#define AT572D940HF_ID_MSIRQ0	26	/* mAgicV SIRQ0 line */
+#define AT572D940HF_ID_MEXC	27	/* mAgicV exception line */
+#define AT572D940HF_ID_MEDMA	28	/* mAgicV end of DMA line */
+#define AT572D940HF_ID_IRQ0	29	/* External Interrupt Source (IRQ0) */
+#define AT572D940HF_ID_IRQ1	30	/* External Interrupt Source (IRQ1) */
+#define AT572D940HF_ID_IRQ2	31	/* External Interrupt Source (IRQ2) */
+
+
+/*
+ * User Peripheral physical base addresses.
+ */
+#define AT572D940HF_BASE_TCB	0xfffa0000
+#define AT572D940HF_BASE_TC0	0xfffa0000
+#define AT572D940HF_BASE_TC1	0xfffa0040
+#define AT572D940HF_BASE_TC2	0xfffa0080
+#define AT572D940HF_BASE_UDP	0xfffa4000
+#define AT572D940HF_BASE_MCI	0xfffa8000
+#define AT572D940HF_BASE_TWI0	0xfffac000
+#define AT572D940HF_BASE_US0	0xfffb0000
+#define AT572D940HF_BASE_US1	0xfffb4000
+#define AT572D940HF_BASE_US2	0xfffb8000
+#define AT572D940HF_BASE_SSC0	0xfffbc000
+#define AT572D940HF_BASE_SSC1	0xfffc0000
+#define AT572D940HF_BASE_SSC2	0xfffc4000
+#define AT572D940HF_BASE_SPI0	0xfffc8000
+#define AT572D940HF_BASE_SPI1	0xfffcc000
+#define AT572D940HF_BASE_SSC3	0xfffd0000
+#define AT572D940HF_BASE_TWI1	0xfffd4000
+#define AT572D940HF_BASE_EMAC	0xfffd8000
+#define AT572D940HF_BASE_CAN0	0xfffdc000
+#define AT572D940HF_BASE_CAN1	0xfffe0000
+#define AT91_BASE_SYS		0xffffea00
+
+
+/*
+ * System Peripherals (offset from AT91_BASE_SYS)
+ */
+#define AT91_SDRAMC	(0xffffea00 - AT91_BASE_SYS)
+#define AT91_SMC	(0xffffec00 - AT91_BASE_SYS)
+#define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
+#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
+#define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
+#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
+#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
+#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
+#define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
+#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
+#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
+#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
+#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
+
+#define AT91_USART0	AT572D940HF_ID_US0
+#define AT91_USART1	AT572D940HF_ID_US1
+#define AT91_USART2	AT572D940HF_ID_US2
+
+
+/*
+ * Internal Memory.
+ */
+#define AT572D940HF_SRAM_BASE	0x00300000	/* Internal SRAM base address */
+#define AT572D940HF_SRAM_SIZE	(48 * SZ_1K)	/* Internal SRAM size (48Kb) */
+
+#define AT572D940HF_ROM_BASE	0x00400000	/* Internal ROM base address */
+#define AT572D940HF_ROM_SIZE	SZ_32K		/* Internal ROM size (32Kb) */
+
+#define AT572D940HF_UHP_BASE	0x00500000	/* USB Host controller */
+
+
+#endif

arch/arm/mach-at91/include/mach/at572d940hf_matrix.h

@@ -0,0 +1,123 @@
+/*
+ * include/mach//at572d940hf_matrix.h
+ *
+ * Antonio R. Costa <costa.antonior@gmail.com>
+ * Copyright (C) 2008 Atmel
+ *
+ * Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef AT572D940HF_MATRIX_H
+#define AT572D940HF_MATRIX_H
+
+#define AT91_MATRIX_MCFG0	(AT91_MATRIX + 0x00)	/* Master Configuration Register 0 */
+#define AT91_MATRIX_MCFG1	(AT91_MATRIX + 0x04)	/* Master Configuration Register 1 */
+#define AT91_MATRIX_MCFG2	(AT91_MATRIX + 0x08)	/* Master Configuration Register 2 */
+#define AT91_MATRIX_MCFG3	(AT91_MATRIX + 0x0C)	/* Master Configuration Register 3 */
+#define AT91_MATRIX_MCFG4	(AT91_MATRIX + 0x10)	/* Master Configuration Register 4 */
+#define AT91_MATRIX_MCFG5	(AT91_MATRIX + 0x14)	/* Master Configuration Register 5 */
+
+#define		AT91_MATRIX_ULBT	(7 << 0)	/* Undefined Length Burst Type */
+#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
+#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
+#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
+#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
+#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
+
+#define AT91_MATRIX_SCFG0	(AT91_MATRIX + 0x40)	/* Slave Configuration Register 0 */
+#define AT91_MATRIX_SCFG1	(AT91_MATRIX + 0x44)	/* Slave Configuration Register 1 */
+#define AT91_MATRIX_SCFG2	(AT91_MATRIX + 0x48)	/* Slave Configuration Register 2 */
+#define AT91_MATRIX_SCFG3	(AT91_MATRIX + 0x4C)	/* Slave Configuration Register 3 */
+#define AT91_MATRIX_SCFG4	(AT91_MATRIX + 0x50)	/* Slave Configuration Register 4 */
+#define		AT91_MATRIX_SLOT_CYCLE		(0xff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
+#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
+#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
+#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
+#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
+#define		AT91_MATRIX_FIXED_DEFMSTR	(0x7  << 18)	/* Fixed Index of Default Master */
+#define		AT91_MATRIX_ARBT		(3    << 24)	/* Arbitration Type */
+#define			AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
+#define			AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
+
+#define AT91_MATRIX_PRAS0	(AT91_MATRIX + 0x80)	/* Priority Register A for Slave 0 */
+#define AT91_MATRIX_PRAS1	(AT91_MATRIX + 0x88)	/* Priority Register A for Slave 1 */
+#define AT91_MATRIX_PRAS2	(AT91_MATRIX + 0x90)	/* Priority Register A for Slave 2 */
+#define AT91_MATRIX_PRAS3	(AT91_MATRIX + 0x98)	/* Priority Register A for Slave 3 */
+#define AT91_MATRIX_PRAS4	(AT91_MATRIX + 0xA0)	/* Priority Register A for Slave 4 */
+
+#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
+#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
+#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
+#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
+#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
+#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
+#define		AT91_MATRIX_M6PR		(3 << 24)	/* Master 6 Priority */
+
+#define AT91_MATRIX_MRCR	(AT91_MATRIX + 0x100)	/* Master Remap Control Register */
+#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
+#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
+
+#define AT91_MATRIX_SFR0	(AT91_MATRIX + 0x110)	/* Special Function Register 0 */
+#define AT91_MATRIX_SFR1	(AT91_MATRIX + 0x114)	/* Special Function Register 1 */
+#define AT91_MATRIX_SFR2	(AT91_MATRIX + 0x118)	/* Special Function Register 2 */
+#define AT91_MATRIX_SFR3	(AT91_MATRIX + 0x11C)	/* Special Function Register 3 */
+#define AT91_MATRIX_SFR4	(AT91_MATRIX + 0x120)	/* Special Function Register 4 */
+#define AT91_MATRIX_SFR5	(AT91_MATRIX + 0x124)	/* Special Function Register 5 */
+#define AT91_MATRIX_SFR6	(AT91_MATRIX + 0x128)	/* Special Function Register 6 */
+#define AT91_MATRIX_SFR7	(AT91_MATRIX + 0x12C)	/* Special Function Register 7 */
+#define AT91_MATRIX_SFR8	(AT91_MATRIX + 0x130)	/* Special Function Register 8 */
+#define AT91_MATRIX_SFR9	(AT91_MATRIX + 0x134)	/* Special Function Register 9 */
+#define AT91_MATRIX_SFR10	(AT91_MATRIX + 0x138)	/* Special Function Register 10 */
+#define AT91_MATRIX_SFR11	(AT91_MATRIX + 0x13C)	/* Special Function Register 11 */
+#define AT91_MATRIX_SFR12	(AT91_MATRIX + 0x140)	/* Special Function Register 12 */
+#define AT91_MATRIX_SFR13	(AT91_MATRIX + 0x144)	/* Special Function Register 13 */
+#define AT91_MATRIX_SFR14	(AT91_MATRIX + 0x148)	/* Special Function Register 14 */
+#define AT91_MATRIX_SFR15	(AT91_MATRIX + 0x14C)	/* Special Function Register 15 */
+
+
+/*
+ * The following registers / bits are not defined in the Datasheet (Revision A)
+ */
+
+#define AT91_MATRIX_TCR		(AT91_MATRIX + 0x100)	/* TCM Configuration Register */
+#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
+#define			AT91_MATRIX_ITCM_0		(0 << 0)
+#define			AT91_MATRIX_ITCM_16		(5 << 0)
+#define			AT91_MATRIX_ITCM_32		(6 << 0)
+#define			AT91_MATRIX_ITCM_64		(7 << 0)
+#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
+#define			AT91_MATRIX_DTCM_0		(0 << 4)
+#define			AT91_MATRIX_DTCM_16		(5 << 4)
+#define			AT91_MATRIX_DTCM_32		(6 << 4)
+#define			AT91_MATRIX_DTCM_64		(7 << 4)
+
+#define AT91_MATRIX_EBICSA	(AT91_MATRIX + 0x11C)	/* EBI Chip Select Assignment Register */
+#define		AT91_MATRIX_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
+#define			AT91_MATRIX_CS1A_SMC		(0 << 1)
+#define			AT91_MATRIX_CS1A_SDRAMC		(1 << 1)
+#define		AT91_MATRIX_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
+#define			AT91_MATRIX_CS3A_SMC		(0 << 3)
+#define			AT91_MATRIX_CS3A_SMC_SMARTMEDIA	(1 << 3)
+#define		AT91_MATRIX_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
+#define			AT91_MATRIX_CS4A_SMC		(0 << 4)
+#define			AT91_MATRIX_CS4A_SMC_CF1	(1 << 4)
+#define		AT91_MATRIX_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
+#define			AT91_MATRIX_CS5A_SMC		(0 << 5)
+#define			AT91_MATRIX_CS5A_SMC_CF2	(1 << 5)
+#define		AT91_MATRIX_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
+
+#endif

arch/arm/mach-at91/include/mach/at91_pmc.h

@@ -32,6 +32,7 @@
 #define		AT91_PMC_PCK1		(1 <<  9)		/* Programmable Clock 1 */
 #define		AT91_PMC_PCK2		(1 << 10)		/* Programmable Clock 2 */
 #define		AT91_PMC_PCK3		(1 << 11)		/* Programmable Clock 3 */
+#define		AT91_PMC_PCK4		(1 << 12)		/* Programmable Clock 4 [AT572D940HF only] */
 #define		AT91_PMC_HCK0		(1 << 16)		/* AHB Clock (USB host) [AT91SAM9261 only] */
 #define		AT91_PMC_HCK1		(1 << 17)		/* AHB Clock (LCD) [AT91SAM9261 only] */
 

arch/arm/mach-at91/include/mach/board.h

@@ -87,7 +87,7 @@ struct at91_eth_data {
 extern void __init at91_add_device_eth(struct at91_eth_data *data);
 
 #if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
-	|| defined(CONFIG_ARCH_AT91SAM9G45)
+	|| defined(CONFIG_ARCH_AT91SAM9G45) || defined(CONFIG_ARCH_AT572D940HF)
 #define eth_platform_data	at91_eth_data
 #endif
 
@@ -205,6 +205,9 @@ extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
 extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
 extern void __init at91_pwm_leds(struct gpio_led *leds, int nr);
 
+ /* AT572D940HF DSP */
+extern void __init at91_add_device_mAgic(void);
+
 /* FIXME: this needs a better location, but gets stuff building again */
 extern int at91_suspend_entering_slow_clock(void);
 

arch/arm/mach-at91/include/mach/cpu.h

@@ -33,6 +33,8 @@
 #define ARCH_ID_AT91SAM9XE256	0x329a93a0
 #define ARCH_ID_AT91SAM9XE512	0x329aa3a0
 
+#define ARCH_ID_AT572D940HF	0x0e0303e0
+
 #define ARCH_ID_AT91M40800	0x14080044
 #define ARCH_ID_AT91R40807	0x44080746
 #define ARCH_ID_AT91M40807	0x14080745
@@ -141,6 +143,12 @@ static inline unsigned long at91cap9_rev_identify(void)
 #define cpu_is_at91cap9_revC()	(0)
 #endif
 
+#ifdef CONFIG_ARCH_AT572D940HF
+#define cpu_is_at572d940hf() (at91_cpu_identify() == ARCH_ID_AT572D940HF)
+#else
+#define cpu_is_at572d940hf() (0)
+#endif
+
 /*
  * Since this is ARM, we will never run on any AVR32 CPU. But these
  * definitions may reduce clutter in common drivers.

arch/arm/mach-at91/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <mach/at91_dbgu.h>
 
-	.macro	addruart,rx
+	.macro	addruart, rx, tmp
 	mrc	p15, 0, \rx, c1, c0
 	tst	\rx, #1						@ MMU enabled?
 	ldreq	\rx, =(AT91_BASE_SYS + AT91_DBGU)		@ System peripherals (phys address)

arch/arm/mach-at91/include/mach/hardware.h

@@ -32,6 +32,8 @@
 #include <mach/at91cap9.h>
 #elif defined(CONFIG_ARCH_AT91X40)
 #include <mach/at91x40.h>
+#elif defined(CONFIG_ARCH_AT572D940HF)
+#include <mach/at572d940hf.h>
 #else
 #error "Unsupported AT91 processor"
 #endif

arch/arm/mach-at91/include/mach/timex.h

@@ -82,6 +82,11 @@
 #define AT91X40_MASTER_CLOCK	40000000
 #define CLOCK_TICK_RATE		(AT91X40_MASTER_CLOCK)
 
+#elif defined(CONFIG_ARCH_AT572D940HF)
+
+#define AT572D940HF_MASTER_CLOCK	80000000
+#define CLOCK_TICK_RATE		(AT572D940HF_MASTER_CLOCK/16)
+
 #endif
 
 #endif

arch/arm/mach-bcmring/core.c

@@ -142,8 +142,7 @@ void __init bcmring_amba_init(void)
 
 	chipcHw_busInterfaceClockEnable(bus_clock);
 
-	for (i = 0; i < ARRAY_SIZE(lookups); i++)
+	clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-		clkdev_add(&lookups[i]);
 
 	for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
 		struct amba_device *d = amba_devs[i];

arch/arm/mach-clps711x/include/mach/debug-macro.S

@@ -13,7 +13,7 @@
 
 #include <asm/hardware/clps7111.h>
 
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #CLPS7111_PHYS_BASE

arch/arm/mach-davinci/include/mach/debug-macro.S

@@ -19,7 +19,7 @@
 #include <linux/serial_reg.h>
 #define UART_SHIFT	2
 
-		.macro addruart, rx
+		.macro addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0x01000000	@ physical base address

arch/arm/mach-davinci/include/mach/hardware.h

@@ -27,7 +27,7 @@
 /*
  * I/O mapping
  */
-#define IO_PHYS				0x01c00000
+#define IO_PHYS				0x01c00000UL
 #define IO_OFFSET			0xfd000000 /* Virtual IO = 0xfec00000 */
 #define IO_SIZE				0x00400000
 #define IO_VIRT				(IO_PHYS + IO_OFFSET)

arch/arm/mach-davinci/io.c

@@ -24,7 +24,7 @@ void __iomem *davinci_ioremap(unsigned long p, size_t size, unsigned int type)
 	if (BETWEEN(p, IO_PHYS, IO_SIZE))
 		return XLATE(p, IO_PHYS, IO_VIRT);
 
-	return __arm_ioremap(p, size, type);
+	return __arm_ioremap_caller(p, size, type, __builtin_return_address(0));
 }
 EXPORT_SYMBOL(davinci_ioremap);
 

arch/arm/mach-dove/include/mach/debug-macro.S

@@ -8,7 +8,7 @@
 
 #include <mach/bridge-regs.h>
 
-	.macro	addruart,rx
+	.macro	addruart, rx, tmp
 	mrc	p15, 0, \rx, c1, c0
 	tst	\rx, #1					@ MMU enabled?
 	ldreq	\rx, =DOVE_SB_REGS_PHYS_BASE

arch/arm/mach-dove/include/mach/vmalloc.h

@@ -2,4 +2,4 @@
  * arch/arm/mach-dove/include/mach/vmalloc.h
  */
 
-#define VMALLOC_END	0xfd800000
+#define VMALLOC_END	0xfd800000UL

arch/arm/mach-ebsa110/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 **/
 
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mov	\rx, #0xf0000000
 		orr	\rx, \rx, #0x00000be0
 		.endm

arch/arm/mach-ep93xx/Kconfig

@@ -161,6 +161,20 @@ config MACH_MICRO9S
 	  Say 'Y' here if you want your kernel to support the
 	  Contec Micro9-Slim board.
 
+config MACH_SIM_ONE
+        bool "Support Simplemachines Sim.One board"
+        depends on EP93XX_SDCE0_PHYS_OFFSET
+        help
+          Say 'Y' here if you want your kernel to support the
+          Simplemachines Sim.One board.
+
+config MACH_SNAPPER_CL15
+	bool "Support Bluewater Systems Snapper CL15 Module"
+	depends on EP93XX_SDCE0_PHYS_OFFSET
+	help
+	  Say 'Y' here if you want your kernel to support the Bluewater
+	  Systems Snapper CL15 Module.
+
 config MACH_TS72XX
 	bool "Support Technologic Systems TS-72xx SBC"
 	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET

arch/arm/mach-ep93xx/Makefile

@@ -10,4 +10,6 @@ obj-$(CONFIG_MACH_ADSSPHERE)	+= adssphere.o
 obj-$(CONFIG_MACH_EDB93XX)	+= edb93xx.o
 obj-$(CONFIG_MACH_GESBC9312)	+= gesbc9312.o
 obj-$(CONFIG_MACH_MICRO9)	+= micro9.o
+obj-$(CONFIG_MACH_SIM_ONE)	+= simone.o
+obj-$(CONFIG_MACH_SNAPPER_CL15)	+= snappercl15.o
 obj-$(CONFIG_MACH_TS72XX)	+= ts72xx.o

arch/arm/mach-ep93xx/clock.c

@@ -10,6 +10,8 @@
  * your option) any later version.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/err.h>
@@ -445,37 +447,39 @@ static void __init ep93xx_dma_clock_init(void)
 static int __init ep93xx_clock_init(void)
 {
 	u32 value;
-	int i;
 
-	value = __raw_readl(EP93XX_SYSCON_CLOCK_SET1);
+	/* Determine the bootloader configured pll1 rate */
-	if (!(value & 0x00800000)) {			/* PLL1 bypassed?  */
+	value = __raw_readl(EP93XX_SYSCON_CLKSET1);
+	if (!(value & EP93XX_SYSCON_CLKSET1_NBYP1))
 		clk_pll1.rate = clk_xtali.rate;
-	} else {
+	else
 		clk_pll1.rate = calc_pll_rate(value);
-	}
+
+	/* Initialize the pll1 derived clocks */
 	clk_f.rate = clk_pll1.rate / fclk_divisors[(value >> 25) & 0x7];
 	clk_h.rate = clk_pll1.rate / hclk_divisors[(value >> 20) & 0x7];
 	clk_p.rate = clk_h.rate / pclk_divisors[(value >> 18) & 0x3];
 	ep93xx_dma_clock_init();
 
-	value = __raw_readl(EP93XX_SYSCON_CLOCK_SET2);
+	/* Determine the bootloader configured pll2 rate */
-	if (!(value & 0x00080000)) {			/* PLL2 bypassed?  */
+	value = __raw_readl(EP93XX_SYSCON_CLKSET2);
+	if (!(value & EP93XX_SYSCON_CLKSET2_NBYP2))
 		clk_pll2.rate = clk_xtali.rate;
-	} else if (value & 0x00040000) {		/* PLL2 enabled?  */
+	else if (value & EP93XX_SYSCON_CLKSET2_PLL2_EN)
 		clk_pll2.rate = calc_pll_rate(value);
-	} else {
+	else
 		clk_pll2.rate = 0;
-	}
+
+	/* Initialize the pll2 derived clocks */
 	clk_usb_host.rate = clk_pll2.rate / (((value >> 28) & 0xf) + 1);
 
-	printk(KERN_INFO "ep93xx: PLL1 running at %ld MHz, PLL2 at %ld MHz\n",
+	pr_info("PLL1 running at %ld MHz, PLL2 at %ld MHz\n",
 		clk_pll1.rate / 1000000, clk_pll2.rate / 1000000);
-	printk(KERN_INFO "ep93xx: FCLK %ld MHz, HCLK %ld MHz, PCLK %ld MHz\n",
+	pr_info("FCLK %ld MHz, HCLK %ld MHz, PCLK %ld MHz\n",
 		clk_f.rate / 1000000, clk_h.rate / 1000000,
 		clk_p.rate / 1000000);
 
-	for (i = 0; i < ARRAY_SIZE(clocks); i++)
+	clkdev_add_table(clocks, ARRAY_SIZE(clocks));
-		clkdev_add(&clocks[i]);
 	return 0;
 }
 arch_initcall(ep93xx_clock_init);

arch/arm/mach-ep93xx/core.c

@@ -14,12 +14,15 @@
  * your option) any later version.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
 #include <linux/dma-mapping.h>
 #include <linux/timex.h>
+#include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
@@ -35,7 +38,6 @@
 
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
-#include <asm/mach/irq.h>
 
 #include <asm/hardware/vic.h>
 
@@ -82,13 +84,40 @@ void __init ep93xx_map_io(void)
  * to use this timer for something else.  We also use timer 4 for keeping
  * track of lost jiffies.
  */
-static unsigned int last_jiffy_time;
+#define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
+#define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
+#define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
+#define EP93XX_TIMER1_CONTROL		EP93XX_TIMER_REG(0x08)
+#define EP93XX_TIMER123_CONTROL_ENABLE	(1 << 7)
+#define EP93XX_TIMER123_CONTROL_MODE	(1 << 6)
+#define EP93XX_TIMER123_CONTROL_CLKSEL	(1 << 3)
+#define EP93XX_TIMER1_CLEAR		EP93XX_TIMER_REG(0x0c)
+#define EP93XX_TIMER2_LOAD		EP93XX_TIMER_REG(0x20)
+#define EP93XX_TIMER2_VALUE		EP93XX_TIMER_REG(0x24)
+#define EP93XX_TIMER2_CONTROL		EP93XX_TIMER_REG(0x28)
+#define EP93XX_TIMER2_CLEAR		EP93XX_TIMER_REG(0x2c)
+#define EP93XX_TIMER4_VALUE_LOW		EP93XX_TIMER_REG(0x60)
+#define EP93XX_TIMER4_VALUE_HIGH	EP93XX_TIMER_REG(0x64)
+#define EP93XX_TIMER4_VALUE_HIGH_ENABLE	(1 << 8)
+#define EP93XX_TIMER3_LOAD		EP93XX_TIMER_REG(0x80)
+#define EP93XX_TIMER3_VALUE		EP93XX_TIMER_REG(0x84)
+#define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
+#define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)
 
+#define EP93XX_TIMER123_CLOCK		508469
+#define EP93XX_TIMER4_CLOCK		983040
+
+#define TIMER1_RELOAD			((EP93XX_TIMER123_CLOCK / HZ) - 1)
 #define TIMER4_TICKS_PER_JIFFY		DIV_ROUND_CLOSEST(CLOCK_TICK_RATE, HZ)
 
+static unsigned int last_jiffy_time;
+
 static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
 {
+	/* Writing any value clears the timer interrupt */
 	__raw_writel(1, EP93XX_TIMER1_CLEAR);
+
+	/* Recover lost jiffies */
 	while ((signed long)
 		(__raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time)
 						>= TIMER4_TICKS_PER_JIFFY) {
@@ -107,13 +136,18 @@ static struct irqaction ep93xx_timer_irq = {
 
 static void __init ep93xx_timer_init(void)
 {
+	u32 tmode = EP93XX_TIMER123_CONTROL_MODE |
+		    EP93XX_TIMER123_CONTROL_CLKSEL;
+
 	/* Enable periodic HZ timer.  */
-	__raw_writel(0x48, EP93XX_TIMER1_CONTROL);
+	__raw_writel(tmode, EP93XX_TIMER1_CONTROL);
-	__raw_writel((508469 / HZ) - 1, EP93XX_TIMER1_LOAD);
+	__raw_writel(TIMER1_RELOAD, EP93XX_TIMER1_LOAD);
-	__raw_writel(0xc8, EP93XX_TIMER1_CONTROL);
+	__raw_writel(tmode | EP93XX_TIMER123_CONTROL_ENABLE,
+			EP93XX_TIMER1_CONTROL);
 
 	/* Enable lost jiffy timer.  */
-	__raw_writel(0x100, EP93XX_TIMER4_VALUE_HIGH);
+	__raw_writel(EP93XX_TIMER4_VALUE_HIGH_ENABLE,
+			EP93XX_TIMER4_VALUE_HIGH);
 
 	setup_irq(IRQ_EP93XX_TIMER1, &ep93xx_timer_irq);
 }
@@ -134,238 +168,17 @@ struct sys_timer ep93xx_timer = {
 };
 
 
-/*************************************************************************
- * GPIO handling for EP93xx
- *************************************************************************/
-static unsigned char gpio_int_unmasked[3];
-static unsigned char gpio_int_enabled[3];
-static unsigned char gpio_int_type1[3];
-static unsigned char gpio_int_type2[3];
-static unsigned char gpio_int_debounce[3];
-
-/* Port ordering is: A B F */
-static const u8 int_type1_register_offset[3]	= { 0x90, 0xac, 0x4c };
-static const u8 int_type2_register_offset[3]	= { 0x94, 0xb0, 0x50 };
-static const u8 eoi_register_offset[3]		= { 0x98, 0xb4, 0x54 };
-static const u8 int_en_register_offset[3]	= { 0x9c, 0xb8, 0x58 };
-static const u8 int_debounce_register_offset[3]	= { 0xa8, 0xc4, 0x64 };
-
-void ep93xx_gpio_update_int_params(unsigned port)
-{
-	BUG_ON(port > 2);
-
-	__raw_writeb(0, EP93XX_GPIO_REG(int_en_register_offset[port]));
-
-	__raw_writeb(gpio_int_type2[port],
-		EP93XX_GPIO_REG(int_type2_register_offset[port]));
-
-	__raw_writeb(gpio_int_type1[port],
-		EP93XX_GPIO_REG(int_type1_register_offset[port]));
-
-	__raw_writeb(gpio_int_unmasked[port] & gpio_int_enabled[port],
-		EP93XX_GPIO_REG(int_en_register_offset[port]));
-}
-
-void ep93xx_gpio_int_mask(unsigned line)
-{
-	gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
-}
-
-void ep93xx_gpio_int_debounce(unsigned int irq, int enable)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-	int port_mask = 1 << (line & 7);
-
-	if (enable)
-		gpio_int_debounce[port] |= port_mask;
-	else
-		gpio_int_debounce[port] &= ~port_mask;
-
-	__raw_writeb(gpio_int_debounce[port],
-		EP93XX_GPIO_REG(int_debounce_register_offset[port]));
-}
-EXPORT_SYMBOL(ep93xx_gpio_int_debounce);
-
 /*************************************************************************
  * EP93xx IRQ handling
  *************************************************************************/
-static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc)
+extern void ep93xx_gpio_init_irq(void);
-{
-	unsigned char status;
-	int i;
-
-	status = __raw_readb(EP93XX_GPIO_A_INT_STATUS);
-	for (i = 0; i < 8; i++) {
-		if (status & (1 << i)) {
-			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_A(0)) + i;
-			generic_handle_irq(gpio_irq);
-		}
-	}
-
-	status = __raw_readb(EP93XX_GPIO_B_INT_STATUS);
-	for (i = 0; i < 8; i++) {
-		if (status & (1 << i)) {
-			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_B(0)) + i;
-			generic_handle_irq(gpio_irq);
-		}
-	}
-}
-
-static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	/*
-	 * map discontiguous hw irq range to continous sw irq range:
-	 *
-	 *  IRQ_EP93XX_GPIO{0..7}MUX -> gpio_to_irq(EP93XX_GPIO_LINE_F({0..7})
-	 */
-	int port_f_idx = ((irq + 1) & 7) ^ 4; /* {19..22,47..50} -> {0..7} */
-	int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_F(0)) + port_f_idx;
-
-	generic_handle_irq(gpio_irq);
-}
-
-static void ep93xx_gpio_irq_ack(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-	int port_mask = 1 << (line & 7);
-
-	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) {
-		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
-		ep93xx_gpio_update_int_params(port);
-	}
-
-	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
-}
-
-static void ep93xx_gpio_irq_mask_ack(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-	int port_mask = 1 << (line & 7);
-
-	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
-		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
-
-	gpio_int_unmasked[port] &= ~port_mask;
-	ep93xx_gpio_update_int_params(port);
-
-	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
-}
-
-static void ep93xx_gpio_irq_mask(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-
-	gpio_int_unmasked[port] &= ~(1 << (line & 7));
-	ep93xx_gpio_update_int_params(port);
-}
-
-static void ep93xx_gpio_irq_unmask(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-
-	gpio_int_unmasked[port] |= 1 << (line & 7);
-	ep93xx_gpio_update_int_params(port);
-}
-
-
-/*
- * gpio_int_type1 controls whether the interrupt is level (0) or
- * edge (1) triggered, while gpio_int_type2 controls whether it
- * triggers on low/falling (0) or high/rising (1).
- */
-static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type)
-{
-	struct irq_desc *desc = irq_desc + irq;
-	const int gpio = irq_to_gpio(irq);
-	const int port = gpio >> 3;
-	const int port_mask = 1 << (gpio & 7);
-
-	gpio_direction_input(gpio);
-
-	switch (type) {
-	case IRQ_TYPE_EDGE_RISING:
-		gpio_int_type1[port] |= port_mask;
-		gpio_int_type2[port] |= port_mask;
-		desc->handle_irq = handle_edge_irq;
-		break;
-	case IRQ_TYPE_EDGE_FALLING:
-		gpio_int_type1[port] |= port_mask;
-		gpio_int_type2[port] &= ~port_mask;
-		desc->handle_irq = handle_edge_irq;
-		break;
-	case IRQ_TYPE_LEVEL_HIGH:
-		gpio_int_type1[port] &= ~port_mask;
-		gpio_int_type2[port] |= port_mask;
-		desc->handle_irq = handle_level_irq;
-		break;
-	case IRQ_TYPE_LEVEL_LOW:
-		gpio_int_type1[port] &= ~port_mask;
-		gpio_int_type2[port] &= ~port_mask;
-		desc->handle_irq = handle_level_irq;
-		break;
-	case IRQ_TYPE_EDGE_BOTH:
-		gpio_int_type1[port] |= port_mask;
-		/* set initial polarity based on current input level */
-		if (gpio_get_value(gpio))
-			gpio_int_type2[port] &= ~port_mask; /* falling */
-		else
-			gpio_int_type2[port] |= port_mask; /* rising */
-		desc->handle_irq = handle_edge_irq;
-		break;
-	default:
-		pr_err("ep93xx: failed to set irq type %d for gpio %d\n",
-		       type, gpio);
-		return -EINVAL;
-	}
-
-	gpio_int_enabled[port] |= port_mask;
-
-	desc->status &= ~IRQ_TYPE_SENSE_MASK;
-	desc->status |= type & IRQ_TYPE_SENSE_MASK;
-
-	ep93xx_gpio_update_int_params(port);
-
-	return 0;
-}
-
-static struct irq_chip ep93xx_gpio_irq_chip = {
-	.name		= "GPIO",
-	.ack		= ep93xx_gpio_irq_ack,
-	.mask_ack	= ep93xx_gpio_irq_mask_ack,
-	.mask		= ep93xx_gpio_irq_mask,
-	.unmask		= ep93xx_gpio_irq_unmask,
-	.set_type	= ep93xx_gpio_irq_type,
-};
-
 
 void __init ep93xx_init_irq(void)
 {
-	int gpio_irq;
-
 	vic_init(EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
 	vic_init(EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
 
-	for (gpio_irq = gpio_to_irq(0);
+	ep93xx_gpio_init_irq();
-	     gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
-		set_irq_chip(gpio_irq, &ep93xx_gpio_irq_chip);
-		set_irq_handler(gpio_irq, handle_level_irq);
-		set_irq_flags(gpio_irq, IRQF_VALID);
-	}
-
-	set_irq_chained_handler(IRQ_EP93XX_GPIO_AB, ep93xx_gpio_ab_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO0MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO1MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO2MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO3MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO4MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO5MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO6MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO7MUX, ep93xx_gpio_f_irq_handler);
 }
 
 
@@ -572,9 +385,9 @@ void __init ep93xx_register_i2c(struct i2c_gpio_platform_data *data,
 	 * CMOS driver.
 	 */
 	if (data->sda_is_open_drain && data->sda_pin != EP93XX_GPIO_LINE_EEDAT)
-		pr_warning("ep93xx: sda != EEDAT, open drain has no effect\n");
+		pr_warning("sda != EEDAT, open drain has no effect\n");
 	if (data->scl_is_open_drain && data->scl_pin != EP93XX_GPIO_LINE_EECLK)
-		pr_warning("ep93xx: scl != EECLK, open drain has no effect\n");
+		pr_warning("scl != EECLK, open drain has no effect\n");
 
 	__raw_writel((data->sda_is_open_drain << 1) |
 		     (data->scl_is_open_drain << 0),

arch/arm/mach-ep93xx/dma-m2p.c

@@ -28,6 +28,8 @@
  * with this implementation.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/err.h>
@@ -173,7 +175,7 @@ static irqreturn_t m2p_irq(int irq, void *dev_id)
 
 	switch (m2p_channel_state(ch)) {
 	case STATE_IDLE:
-		pr_crit("m2p_irq: dma interrupt without a dma buffer\n");
+		pr_crit("dma interrupt without a dma buffer\n");
 		BUG();
 		break;
 
@@ -197,7 +199,7 @@ static irqreturn_t m2p_irq(int irq, void *dev_id)
 		break;
 
 	case STATE_NEXT:
-		pr_crit("m2p_irq: dma interrupt while next\n");
+		pr_crit("dma interrupt while next\n");
 		BUG();
 		break;
 	}

arch/arm/mach-ep93xx/edb93xx.c

@@ -118,12 +118,33 @@ static void __init edb93xx_register_i2c(void)
 	}
 }
 
+
+/*************************************************************************
+ * EDB93xx pwm
+ *************************************************************************/
+static void __init edb93xx_register_pwm(void)
+{
+	if (machine_is_edb9301() ||
+	    machine_is_edb9302() || machine_is_edb9302a()) {
+		/* EP9301 and EP9302 only have pwm.1 (EGPIO14) */
+		ep93xx_register_pwm(0, 1);
+	} else if (machine_is_edb9307() || machine_is_edb9307a()) {
+		/* EP9307 only has pwm.0 (PWMOUT) */
+		ep93xx_register_pwm(1, 0);
+	} else {
+		/* EP9312 and EP9315 have both */
+		ep93xx_register_pwm(1, 1);
+	}
+}
+
+
 static void __init edb93xx_init_machine(void)
 {
 	ep93xx_init_devices();
 	edb93xx_register_flash();
 	ep93xx_register_eth(&edb93xx_eth_data, 1);
 	edb93xx_register_i2c();
+	edb93xx_register_pwm();
 }
 
 

arch/arm/mach-ep93xx/gpio.c

@@ -13,6 +13,8 @@
  *  published by the Free Software Foundation.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/seq_file.h>
@@ -22,6 +24,235 @@
 
 #include <mach/hardware.h>
 
+/*************************************************************************
+ * GPIO handling for EP93xx
+ *************************************************************************/
+static unsigned char gpio_int_unmasked[3];
+static unsigned char gpio_int_enabled[3];
+static unsigned char gpio_int_type1[3];
+static unsigned char gpio_int_type2[3];
+static unsigned char gpio_int_debounce[3];
+
+/* Port ordering is: A B F */
+static const u8 int_type1_register_offset[3]	= { 0x90, 0xac, 0x4c };
+static const u8 int_type2_register_offset[3]	= { 0x94, 0xb0, 0x50 };
+static const u8 eoi_register_offset[3]		= { 0x98, 0xb4, 0x54 };
+static const u8 int_en_register_offset[3]	= { 0x9c, 0xb8, 0x58 };
+static const u8 int_debounce_register_offset[3]	= { 0xa8, 0xc4, 0x64 };
+
+void ep93xx_gpio_update_int_params(unsigned port)
+{
+	BUG_ON(port > 2);
+
+	__raw_writeb(0, EP93XX_GPIO_REG(int_en_register_offset[port]));
+
+	__raw_writeb(gpio_int_type2[port],
+		EP93XX_GPIO_REG(int_type2_register_offset[port]));
+
+	__raw_writeb(gpio_int_type1[port],
+		EP93XX_GPIO_REG(int_type1_register_offset[port]));
+
+	__raw_writeb(gpio_int_unmasked[port] & gpio_int_enabled[port],
+		EP93XX_GPIO_REG(int_en_register_offset[port]));
+}
+
+void ep93xx_gpio_int_mask(unsigned line)
+{
+	gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
+}
+
+void ep93xx_gpio_int_debounce(unsigned int irq, int enable)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if (enable)
+		gpio_int_debounce[port] |= port_mask;
+	else
+		gpio_int_debounce[port] &= ~port_mask;
+
+	__raw_writeb(gpio_int_debounce[port],
+		EP93XX_GPIO_REG(int_debounce_register_offset[port]));
+}
+EXPORT_SYMBOL(ep93xx_gpio_int_debounce);
+
+static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	unsigned char status;
+	int i;
+
+	status = __raw_readb(EP93XX_GPIO_A_INT_STATUS);
+	for (i = 0; i < 8; i++) {
+		if (status & (1 << i)) {
+			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_A(0)) + i;
+			generic_handle_irq(gpio_irq);
+		}
+	}
+
+	status = __raw_readb(EP93XX_GPIO_B_INT_STATUS);
+	for (i = 0; i < 8; i++) {
+		if (status & (1 << i)) {
+			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_B(0)) + i;
+			generic_handle_irq(gpio_irq);
+		}
+	}
+}
+
+static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	/*
+	 * map discontiguous hw irq range to continous sw irq range:
+	 *
+	 *  IRQ_EP93XX_GPIO{0..7}MUX -> gpio_to_irq(EP93XX_GPIO_LINE_F({0..7})
+	 */
+	int port_f_idx = ((irq + 1) & 7) ^ 4; /* {19..22,47..50} -> {0..7} */
+	int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_F(0)) + port_f_idx;
+
+	generic_handle_irq(gpio_irq);
+}
+
+static void ep93xx_gpio_irq_ack(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) {
+		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
+		ep93xx_gpio_update_int_params(port);
+	}
+
+	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
+}
+
+static void ep93xx_gpio_irq_mask_ack(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
+		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
+
+	gpio_int_unmasked[port] &= ~port_mask;
+	ep93xx_gpio_update_int_params(port);
+
+	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
+}
+
+static void ep93xx_gpio_irq_mask(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+
+	gpio_int_unmasked[port] &= ~(1 << (line & 7));
+	ep93xx_gpio_update_int_params(port);
+}
+
+static void ep93xx_gpio_irq_unmask(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+
+	gpio_int_unmasked[port] |= 1 << (line & 7);
+	ep93xx_gpio_update_int_params(port);
+}
+
+/*
+ * gpio_int_type1 controls whether the interrupt is level (0) or
+ * edge (1) triggered, while gpio_int_type2 controls whether it
+ * triggers on low/falling (0) or high/rising (1).
+ */
+static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type)
+{
+	struct irq_desc *desc = irq_desc + irq;
+	const int gpio = irq_to_gpio(irq);
+	const int port = gpio >> 3;
+	const int port_mask = 1 << (gpio & 7);
+
+	gpio_direction_input(gpio);
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		gpio_int_type1[port] |= port_mask;
+		gpio_int_type2[port] |= port_mask;
+		desc->handle_irq = handle_edge_irq;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		gpio_int_type1[port] |= port_mask;
+		gpio_int_type2[port] &= ~port_mask;
+		desc->handle_irq = handle_edge_irq;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		gpio_int_type1[port] &= ~port_mask;
+		gpio_int_type2[port] |= port_mask;
+		desc->handle_irq = handle_level_irq;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		gpio_int_type1[port] &= ~port_mask;
+		gpio_int_type2[port] &= ~port_mask;
+		desc->handle_irq = handle_level_irq;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		gpio_int_type1[port] |= port_mask;
+		/* set initial polarity based on current input level */
+		if (gpio_get_value(gpio))
+			gpio_int_type2[port] &= ~port_mask; /* falling */
+		else
+			gpio_int_type2[port] |= port_mask; /* rising */
+		desc->handle_irq = handle_edge_irq;
+		break;
+	default:
+		pr_err("failed to set irq type %d for gpio %d\n", type, gpio);
+		return -EINVAL;
+	}
+
+	gpio_int_enabled[port] |= port_mask;
+
+	desc->status &= ~IRQ_TYPE_SENSE_MASK;
+	desc->status |= type & IRQ_TYPE_SENSE_MASK;
+
+	ep93xx_gpio_update_int_params(port);
+
+	return 0;
+}
+
+static struct irq_chip ep93xx_gpio_irq_chip = {
+	.name		= "GPIO",
+	.ack		= ep93xx_gpio_irq_ack,
+	.mask_ack	= ep93xx_gpio_irq_mask_ack,
+	.mask		= ep93xx_gpio_irq_mask,
+	.unmask		= ep93xx_gpio_irq_unmask,
+	.set_type	= ep93xx_gpio_irq_type,
+};
+
+void __init ep93xx_gpio_init_irq(void)
+{
+	int gpio_irq;
+
+	for (gpio_irq = gpio_to_irq(0);
+	     gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
+		set_irq_chip(gpio_irq, &ep93xx_gpio_irq_chip);
+		set_irq_handler(gpio_irq, handle_level_irq);
+		set_irq_flags(gpio_irq, IRQF_VALID);
+	}
+
+	set_irq_chained_handler(IRQ_EP93XX_GPIO_AB, ep93xx_gpio_ab_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO0MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO1MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO2MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO3MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO4MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO5MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO6MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO7MUX, ep93xx_gpio_f_irq_handler);
+}
+
+
+/*************************************************************************
+ * gpiolib interface for EP93xx on-chip GPIOs
+ *************************************************************************/
 struct ep93xx_gpio_chip {
 	struct gpio_chip	chip;
 
@@ -31,10 +262,6 @@ struct ep93xx_gpio_chip {
 
 #define to_ep93xx_gpio_chip(c) container_of(c, struct ep93xx_gpio_chip, chip)
 
-/* From core.c */
-extern void ep93xx_gpio_int_mask(unsigned line);
-extern void ep93xx_gpio_update_int_params(unsigned port);
-
 static int ep93xx_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
 	struct ep93xx_gpio_chip *ep93xx_chip = to_ep93xx_gpio_chip(chip);

arch/arm/mach-ep93xx/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  */
 #include <mach/ep93xx-regs.h>
 
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1				@ MMU enabled?
 		ldreq	\rx, =EP93XX_APB_PHYS_BASE	@ Physical base

arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h

@@ -92,21 +92,6 @@
 
 /* APB peripherals */
 #define EP93XX_TIMER_BASE		EP93XX_APB_IOMEM(0x00010000)
-#define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
-#define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
-#define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
-#define EP93XX_TIMER1_CONTROL		EP93XX_TIMER_REG(0x08)
-#define EP93XX_TIMER1_CLEAR		EP93XX_TIMER_REG(0x0c)
-#define EP93XX_TIMER2_LOAD		EP93XX_TIMER_REG(0x20)
-#define EP93XX_TIMER2_VALUE		EP93XX_TIMER_REG(0x24)
-#define EP93XX_TIMER2_CONTROL		EP93XX_TIMER_REG(0x28)
-#define EP93XX_TIMER2_CLEAR		EP93XX_TIMER_REG(0x2c)
-#define EP93XX_TIMER4_VALUE_LOW		EP93XX_TIMER_REG(0x60)
-#define EP93XX_TIMER4_VALUE_HIGH	EP93XX_TIMER_REG(0x64)
-#define EP93XX_TIMER3_LOAD		EP93XX_TIMER_REG(0x80)
-#define EP93XX_TIMER3_VALUE		EP93XX_TIMER_REG(0x84)
-#define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
-#define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)
 
 #define EP93XX_I2S_BASE			EP93XX_APB_IOMEM(0x00020000)
 
@@ -167,8 +152,11 @@
 #define EP93XX_SYSCON_PWRCNT_DMA_M2P1	(1<<16)
 #define EP93XX_SYSCON_HALT		EP93XX_SYSCON_REG(0x08)
 #define EP93XX_SYSCON_STANDBY		EP93XX_SYSCON_REG(0x0c)
-#define EP93XX_SYSCON_CLOCK_SET1	EP93XX_SYSCON_REG(0x20)
+#define EP93XX_SYSCON_CLKSET1		EP93XX_SYSCON_REG(0x20)
-#define EP93XX_SYSCON_CLOCK_SET2	EP93XX_SYSCON_REG(0x24)
+#define EP93XX_SYSCON_CLKSET1_NBYP1	(1<<23)
+#define EP93XX_SYSCON_CLKSET2		EP93XX_SYSCON_REG(0x24)
+#define EP93XX_SYSCON_CLKSET2_NBYP2	(1<<19)
+#define EP93XX_SYSCON_CLKSET2_PLL2_EN	(1<<18)
 #define EP93XX_SYSCON_DEVCFG		EP93XX_SYSCON_REG(0x80)
 #define EP93XX_SYSCON_DEVCFG_SWRST	(1<<31)
 #define EP93XX_SYSCON_DEVCFG_D1ONG	(1<<30)

arch/arm/mach-ep93xx/include/mach/vmalloc.h

@@ -2,4 +2,4 @@
  * arch/arm/mach-ep93xx/include/mach/vmalloc.h
  */
 
-#define VMALLOC_END	0xfe800000
+#define VMALLOC_END	0xfe800000UL

arch/arm/mach-ep93xx/simone.c

@@ -0,0 +1,97 @@
+/*
+ * arch/arm/mach-ep93xx/simone.c
+ * Simplemachines Sim.One support.
+ *
+ * Copyright (C) 2010 Ryan Mallon <ryan@bluewatersys.com>
+ *
+ * Based on the 2.6.24.7 support:
+ *   Copyright (C) 2009 Simplemachines
+ *   MMC support by Peter Ivanov <ivanovp@gmail.com>, 2007
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+static struct physmap_flash_data simone_flash_data = {
+	.width		= 2,
+};
+
+static struct resource simone_flash_resource = {
+	.start		= EP93XX_CS6_PHYS_BASE,
+	.end		= EP93XX_CS6_PHYS_BASE + SZ_8M - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device simone_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.num_resources	= 1,
+	.resource	= &simone_flash_resource,
+	.dev = {
+		.platform_data	= &simone_flash_data,
+	},
+};
+
+static struct ep93xx_eth_data simone_eth_data = {
+	.phy_id		= 1,
+};
+
+static struct ep93xxfb_mach_info simone_fb_info = {
+	.num_modes	= EP93XXFB_USE_MODEDB,
+	.bpp		= 16,
+	.flags		= EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
+};
+
+static struct i2c_gpio_platform_data simone_i2c_gpio_data = {
+	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
+	.sda_is_open_drain	= 0,
+	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
+	.scl_is_open_drain	= 0,
+	.udelay			= 0,
+	.timeout		= 0,
+};
+
+static struct i2c_board_info __initdata simone_i2c_board_info[] = {
+	{
+		I2C_BOARD_INFO("ds1337", 0x68),
+	},
+};
+
+static void __init simone_init_machine(void)
+{
+	ep93xx_init_devices();
+
+	platform_device_register(&simone_flash);
+	ep93xx_register_eth(&simone_eth_data, 1);
+	ep93xx_register_fb(&simone_fb_info);
+	ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info,
+			    ARRAY_SIZE(simone_i2c_board_info));
+}
+
+MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
+/* Maintainer: Ryan Mallon <ryan@bluewatersys.com> */
+	.phys_io	= EP93XX_APB_PHYS_BASE,
+	.io_pg_offst	= ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.map_io		= ep93xx_map_io,
+	.init_irq	= ep93xx_init_irq,
+	.timer		= &ep93xx_timer,
+	.init_machine	= simone_init_machine,
+MACHINE_END

arch/arm/mach-ep93xx/snappercl15.c

@@ -0,0 +1,172 @@
+/*
+ * arch/arm/mach-ep93xx/snappercl15.c
+ * Bluewater Systems Snapper CL15 system module
+ *
+ * Copyright (C) 2009 Bluewater Systems Ltd
+ * Author: Ryan Mallon <ryan@bluewatersys.com>
+ *
+ * NAND code adapted from driver by:
+ *   Andre Renaud <andre@bluewatersys.com>
+ *   James R. McKaskill
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <linux/fb.h>
+
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#define SNAPPERCL15_NAND_BASE	(EP93XX_CS7_PHYS_BASE + SZ_16M)
+
+#define SNAPPERCL15_NAND_WPN	(1 << 8)  /* Write protect (active low) */
+#define SNAPPERCL15_NAND_ALE	(1 << 9)  /* Address latch */
+#define SNAPPERCL15_NAND_CLE	(1 << 10) /* Command latch */
+#define SNAPPERCL15_NAND_CEN	(1 << 11) /* Chip enable (active low) */
+#define SNAPPERCL15_NAND_RDY	(1 << 14) /* Device ready */
+
+#define NAND_CTRL_ADDR(chip) 	(chip->IO_ADDR_W + 0x40)
+
+static void snappercl15_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+				      unsigned int ctrl)
+{
+	struct nand_chip *chip = mtd->priv;
+	static u16 nand_state = SNAPPERCL15_NAND_WPN;
+	u16 set;
+
+	if (ctrl & NAND_CTRL_CHANGE) {
+		set = SNAPPERCL15_NAND_CEN | SNAPPERCL15_NAND_WPN;
+
+		if (ctrl & NAND_NCE)
+			set &= ~SNAPPERCL15_NAND_CEN;
+		if (ctrl & NAND_CLE)
+			set |= SNAPPERCL15_NAND_CLE;
+		if (ctrl & NAND_ALE)
+			set |= SNAPPERCL15_NAND_ALE;
+
+		nand_state &= ~(SNAPPERCL15_NAND_CEN |
+				SNAPPERCL15_NAND_CLE |
+				SNAPPERCL15_NAND_ALE);
+		nand_state |= set;
+		__raw_writew(nand_state, NAND_CTRL_ADDR(chip));
+	}
+
+	if (cmd != NAND_CMD_NONE)
+		__raw_writew((cmd & 0xff) | nand_state, chip->IO_ADDR_W);
+}
+
+static int snappercl15_nand_dev_ready(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+
+	return !!(__raw_readw(NAND_CTRL_ADDR(chip)) & SNAPPERCL15_NAND_RDY);
+}
+
+static const char *snappercl15_nand_part_probes[] = {"cmdlinepart", NULL};
+
+static struct mtd_partition snappercl15_nand_parts[] = {
+	{
+		.name		= "Kernel",
+		.offset		= 0,
+		.size		= SZ_2M,
+	},
+	{
+		.name		= "Filesystem",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct platform_nand_data snappercl15_nand_data = {
+	.chip = {
+		.nr_chips		= 1,
+		.part_probe_types	= snappercl15_nand_part_probes,
+		.partitions		= snappercl15_nand_parts,
+		.nr_partitions		= ARRAY_SIZE(snappercl15_nand_parts),
+		.options		= NAND_NO_AUTOINCR,
+		.chip_delay		= 25,
+	},
+	.ctrl = {
+		.dev_ready		= snappercl15_nand_dev_ready,
+		.cmd_ctrl		= snappercl15_nand_cmd_ctrl,
+	},
+};
+
+static struct resource snappercl15_nand_resource[] = {
+	{
+		.start		= SNAPPERCL15_NAND_BASE,
+		.end		= SNAPPERCL15_NAND_BASE + SZ_4K - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device snappercl15_nand_device = {
+	.name			= "gen_nand",
+	.id			= -1,
+	.dev.platform_data	= &snappercl15_nand_data,
+	.resource		= snappercl15_nand_resource,
+	.num_resources		= ARRAY_SIZE(snappercl15_nand_resource),
+};
+
+static struct ep93xx_eth_data snappercl15_eth_data = {
+	.phy_id			= 1,
+};
+
+static struct i2c_gpio_platform_data snappercl15_i2c_gpio_data = {
+	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
+	.sda_is_open_drain	= 0,
+	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
+	.scl_is_open_drain	= 0,
+	.udelay			= 0,
+	.timeout		= 0,
+};
+
+static struct i2c_board_info __initdata snappercl15_i2c_data[] = {
+	{
+		/* Audio codec */
+		I2C_BOARD_INFO("tlv320aic23", 0x1a),
+	},
+};
+
+static struct ep93xxfb_mach_info snappercl15_fb_info = {
+	.num_modes		= EP93XXFB_USE_MODEDB,
+	.bpp			= 16,
+};
+
+static void __init snappercl15_init_machine(void)
+{
+	ep93xx_init_devices();
+	ep93xx_register_eth(&snappercl15_eth_data, 1);
+	ep93xx_register_i2c(&snappercl15_i2c_gpio_data, snappercl15_i2c_data,
+			    ARRAY_SIZE(snappercl15_i2c_data));
+	ep93xx_register_fb(&snappercl15_fb_info);
+	platform_device_register(&snappercl15_nand_device);
+}
+
+MACHINE_START(SNAPPER_CL15, "Bluewater Systems Snapper CL15")
+	/* Maintainer: Ryan Mallon <ryan@bluewatersys.com> */
+	.phys_io	= EP93XX_APB_PHYS_BASE,
+	.io_pg_offst	= ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.map_io		= ep93xx_map_io,
+	.init_irq	= ep93xx_init_irq,
+	.timer 		= &ep93xx_timer,
+	.init_machine	= snappercl15_init_machine,
+MACHINE_END

arch/arm/mach-footbridge/common.c

@@ -32,12 +32,13 @@ unsigned int mem_fclk_21285 = 50000000;
 
 EXPORT_SYMBOL(mem_fclk_21285);
 
-static void __init early_fclk(char **arg)
+static int __init early_fclk(char *arg)
 {
-	mem_fclk_21285 = simple_strtoul(*arg, arg, 0);
+	mem_fclk_21285 = simple_strtoul(arg, NULL, 0);
+	return 0;
 }
 
-__early_param("mem_fclk_21285=", early_fclk);
+early_param("mem_fclk_21285", early_fclk);
 
 static int __init parse_tag_memclk(const struct tag *tag)
 {

arch/arm/mach-footbridge/include/mach/debug-macro.S

@@ -15,7 +15,7 @@
 
 #ifndef CONFIG_DEBUG_DC21285_PORT
 	/* For NetWinder debugging */
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0x7c000000	@ physical
@@ -32,7 +32,7 @@
 		.equ	dc21285_high, ARMCSR_BASE & 0xff000000
 		.equ	dc21285_low,  ARMCSR_BASE & 0x00ffffff
 
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0x42000000

arch/arm/mach-gemini/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  */
 #include <mach/hardware.h>
 
-	.macro	addruart,rx
+	.macro	addruart, rx, tmp
 	mrc	p15, 0, \rx, c1, c0
 	tst	\rx, #1					@ MMU enabled?
 	ldreq	\rx, =GEMINI_UART_BASE			@ physical

arch/arm/mach-gemini/include/mach/vmalloc.h

@@ -7,4 +7,4 @@
  * (at your option) any later version.
  */
 
-#define VMALLOC_END	0xF0000000
+#define VMALLOC_END	0xf0000000UL

arch/arm/mach-h720x/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 		.equ    io_virt, IO_BASE
 		.equ    io_phys, IO_START
 
-		.macro  addruart,rx
+		.macro  addruart, rx, tmp
 		mrc     p15, 0, \rx, c1, c0
 		tst     \rx, #1  	       @ MMU enabled?
 		moveq   \rx, #io_phys	       @ physical base address

arch/arm/mach-integrator/core.c

@@ -144,8 +144,7 @@ static int __init integrator_init(void)
 {
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(lookups); i++)
+	clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-		clkdev_add(&lookups[i]);
 
 	for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
 		struct amba_device *d = amba_devs[i];

arch/arm/mach-integrator/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0x16000000	@ physical base address

arch/arm/mach-integrator/integrator_cp.c

@@ -558,9 +558,7 @@ static void __init intcp_init(void)
 {
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(cp_lookups); i++)
+	clkdev_add_table(cp_lookups, ARRAY_SIZE(cp_lookups));
-		clkdev_add(&cp_lookups[i]);
-
 	platform_add_devices(intcp_devs, ARRAY_SIZE(intcp_devs));
 
 	for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {

arch/arm/mach-iop13xx/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-	.macro	addruart, rx
+	.macro	addruart, rx, tmp
 	mrc	p15, 0, \rx, c1, c0
 	tst	\rx, #1			@ mmu enabled?
 	moveq	\rx, #0xff000000	@ physical

arch/arm/mach-iop13xx/io.c

@@ -61,9 +61,9 @@ void * __iomem __iop13xx_ioremap(unsigned long cookie, size_t size,
 			         (cookie - IOP13XX_PCIE_LOWER_MEM_RA));
 		break;
 	case IOP13XX_PBI_LOWER_MEM_RA ... IOP13XX_PBI_UPPER_MEM_RA:
-		retval = __arm_ioremap(IOP13XX_PBI_LOWER_MEM_PA +
+		retval = __arm_ioremap_caller(IOP13XX_PBI_LOWER_MEM_PA +
 				       (cookie - IOP13XX_PBI_LOWER_MEM_RA),
-				       size, mtype);
+				       size, mtype, __builtin_return_address(0));
 		break;
 	case IOP13XX_PCIE_LOWER_IO_PA ... IOP13XX_PCIE_UPPER_IO_PA:
 		retval = (void *) IOP13XX_PCIE_IO_PHYS_TO_VIRT(cookie);
@@ -75,7 +75,8 @@ void * __iomem __iop13xx_ioremap(unsigned long cookie, size_t size,
 		retval = (void *) IOP13XX_PMMR_PHYS_TO_VIRT(cookie);
 		break;
 	default:
-		retval = __arm_ioremap(cookie, size, mtype);
+		retval = __arm_ioremap_caller(cookie, size, mtype,
+				__builtin_return_address(0));
 	}
 
 	return retval;

arch/arm/mach-iop32x/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart, rx
+		.macro	addruart, rx, tmp
 		mov	\rx, #0xfe000000	@ physical as well as virtual
 		orr	\rx, \rx, #0x00800000	@ location of the UART
 		.endm

arch/arm/mach-iop32x/include/mach/vmalloc.h

@@ -2,4 +2,4 @@
  * arch/arm/mach-iop32x/include/mach/vmalloc.h
  */
 
-#define VMALLOC_END	0xfe000000
+#define VMALLOC_END	0xfe000000UL

arch/arm/mach-iop33x/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart, rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ mmu enabled?
 		moveq	\rx, #0xff000000	@ physical

arch/arm/mach-iop33x/include/mach/vmalloc.h

@@ -2,4 +2,4 @@
  * arch/arm/mach-iop33x/include/mach/vmalloc.h
  */
 
-#define VMALLOC_END	0xfe000000
+#define VMALLOC_END	0xfe000000UL

arch/arm/mach-ixp2000/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro  addruart,rx
+		.macro  addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0xc0000000	@ Physical base

arch/arm/mach-ixp2000/include/mach/vmalloc.h

@@ -17,4 +17,4 @@
  * The vmalloc() routines leaves a hole of 4kB between each vmalloced
  * area for the same reason. ;)
  */
-#define VMALLOC_END	    0xfb000000
+#define VMALLOC_END	    0xfb000000UL

arch/arm/mach-ixp23xx/include/mach/debug-macro.S

@@ -12,7 +12,7 @@
  */
 #include <mach/ixp23xx.h>
 
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1				@ mmu enabled?
 		ldreq	\rx, =IXP23XX_PERIPHERAL_PHYS 	@ physical

arch/arm/mach-ixp23xx/include/mach/vmalloc.h

@@ -7,4 +7,4 @@
  * specific static I/O.
  */
 
-#define VMALLOC_END	(0xec000000)
+#define VMALLOC_END	(0xec000000UL)