diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
index 3a6a1e0c1e32..124a80901084 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
index b73deb282120..bba98f982ad6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */
diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
index 8647da7d6609..eac5720dc15f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
@@ -246,6 +246,10 @@ &ir {
 	linux,rc-map-name = "rc-khadas";
 };
 
+&pcie {
+	reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>;
+};
+
 &pwm_ef {
         status = "okay";
         pinctrl-0 = <&pwm_e_pins>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
index 5233bd7cacfb..dbbf29a0dbf6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
@@ -68,3 +68,28 @@ &pwm_AO_cd {
 	clock-names = "clkin1";
 	status = "okay";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */