openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity

iio: adc: mcp320x: Add support for mcp3550/1/3 

These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but
in reality their resolution is 21 bit with an overrange or underrange
of 12% beyond Vref.  In other words, "full scale" means +/- 2^20.

This driver does not explicitly signal back to the user when an
overrange or underrange occurs, but the user can detect it by comparing
the raw value to +/- 2^20 (or the scaled value to Vref).

The chips feature an extended temperature range and high accuracy,
low noise characteristics, but their conversion times are slow with
up to 80 ms +/- 2% (on the MCP3550-50).

Hence, unlike the other ADCs supported by the driver, conversion does
not take place in realtime upon lowering CS.  Instead, CS is asserted
for 8 usec to start the conversion.  After waiting for the duration of
the conversion, the result can be fetched.  While waiting, control of
the bus is ceased so it may be used by a different device.

After the result has been fetched and 10 us have passed, the chip goes
into shutdown and an additional power-up delay of 144 clock periods is
then required to wake the analog circuitry upon the next conversion
(footnote below table 4-1, page 16 in the spec).

Optionally, the chips can be used in so-called "continuous conversion
mode":  Conversions then take place continuously and the last result may
be fetched at any time without observing a delay.  The mode is enabled
by permanently driving CS low, e.g. by wiring it to ground.  The driver
only supports "single conversion mode" for now but should be adaptable
to "continuous conversion mode" with moderate effort.

The chips clock out a 3 byte word, unlike the other ADCs supported by
the driver which all have a lower resolution than 16 bit and thus make
do with 2 bytes.  Calculate the word length on probe by rounding up the
resolution to full bytes.  Crucially, if the clock idles low, the
transfer is preceded by a useless Data Ready bit which increases its
length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec).
Autosense this based on the SPI slave's configuration.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit is contained in:
Lukas Wunner 2017-09-09 20:32:41 +02:00 committed by Jonathan Cameron
parent 2db82e320d
commit c1375d671a
2 changed files with 118 additions and 7 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

5
drivers/iio/adc/Kconfig
View File

@ -475,12 +475,13 @@ config MAX9611
called max9611.
config MCP320X
tristate "Microchip Technology MCP3x01/02/04/08"
tristate "Microchip Technology MCP3x01/02/04/08 and MCP3550/1/3"
depends on SPI
help
Say yes here to build support for Microchip Technology's
MCP3001, MCP3002, MCP3004, MCP3008, MCP3201, MCP3202, MCP3204,
MCP3208 or MCP3301 analog to digital converter.
MCP3208, MCP3301, MCP3550, MCP3551 and MCP3553 analog to digital
converters.
This driver can also be built as a module. If so, the module will be
called mcp320x.

120
drivers/iio/adc/mcp320x.c
View File

@ -19,6 +19,11 @@
* ------------
* 13 bit converter
* MCP3301
* ------------
* 22 bit converter
* MCP3550
* MCP3551
* MCP3553
*
* Datasheet can be found here:
* http://ww1.microchip.com/downloads/en/DeviceDoc/21293C.pdf mcp3001
@ -28,6 +33,7 @@
* http://ww1.microchip.com/downloads/en/DeviceDoc/21034D.pdf mcp3202
* http://ww1.microchip.com/downloads/en/DeviceDoc/21298c.pdf mcp3204/08
* http://ww1.microchip.com/downloads/en/DeviceDoc/21700E.pdf mcp3301
* http://ww1.microchip.com/downloads/en/DeviceDoc/21950D.pdf mcp3550/1/3
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@ -51,12 +57,17 @@ enum {
mcp3204,
mcp3208,
mcp3301,
mcp3550_50,
mcp3550_60,
mcp3551,
mcp3553,
};
struct mcp320x_chip_info {
const struct iio_chan_spec *channels;
unsigned int num_channels;
unsigned int resolution;
unsigned int conv_time; /* usec */
};
/**
@ -64,6 +75,8 @@ struct mcp320x_chip_info {
* @spi: SPI slave (parent of the IIO device)
* @msg: SPI message to select a channel and receive a value from the ADC
* @transfer: SPI transfers used by @msg
* @start_conv_msg: SPI message to start a conversion by briefly asserting CS
* @start_conv_transfer: SPI transfer used by @start_conv_msg
* @reg: regulator generating Vref
* @lock: protects read sequences
* @chip_info: ADC properties
@ -74,13 +87,15 @@ struct mcp320x {
struct spi_device *spi;
struct spi_message msg;
struct spi_transfer transfer[2];
struct spi_message start_conv_msg;
struct spi_transfer start_conv_transfer;
struct regulator *reg;
struct mutex lock;
const struct mcp320x_chip_info *chip_info;
u8 tx_buf ____cacheline_aligned;
u8 rx_buf[2];
u8 rx_buf[4];
};
static int mcp320x_channel_to_tx_data(int device_index,
@ -109,6 +124,15 @@ static int mcp320x_adc_conversion(struct mcp320x *adc, u8 channel,
{
int ret;
if (adc->chip_info->conv_time) {
ret = spi_sync(adc->spi, &adc->start_conv_msg);
if (ret < 0)
return ret;
usleep_range(adc->chip_info->conv_time,
adc->chip_info->conv_time + 100);
}
memset(&adc->rx_buf, 0, sizeof(adc->rx_buf));
if (adc->chip_info->num_channels > 1)
adc->tx_buf = mcp320x_channel_to_tx_data(device_index, channel,
@ -139,6 +163,31 @@ static int mcp320x_adc_conversion(struct mcp320x *adc, u8 channel,
*val = sign_extend32((adc->rx_buf[0] & 0x1f) << 8
| adc->rx_buf[1], 12);
return 0;
case mcp3550_50:
case mcp3550_60:
case mcp3551:
case mcp3553: {
u32 raw = be32_to_cpup((u32 *)adc->rx_buf);
if (!(adc->spi->mode & SPI_CPOL))
raw <<= 1; /* strip Data Ready bit in SPI mode 0,0 */
/*
* If the input is within -vref and vref, bit 21 is the sign.
* Up to 12% overrange or underrange are allowed, in which case
* bit 23 is the sign and bit 0 to 21 is the value.
*/
raw >>= 8;
if (raw & BIT(22) && raw & BIT(23))
return -EIO; /* cannot have overrange AND underrange */
else if (raw & BIT(22))
raw &= ~BIT(22); /* overrange */
else if (raw & BIT(23) || raw & BIT(21))
raw |= GENMASK(31, 22); /* underrange or negative */
*val = (s32)raw;
return 0;
}
default:
return -EINVAL;
}
@ -297,6 +346,31 @@ static const struct mcp320x_chip_info mcp320x_chip_infos[] = {
.num_channels = ARRAY_SIZE(mcp3201_channels),
.resolution = 13
},
[mcp3550_50] = {
.channels = mcp3201_channels,
.num_channels = ARRAY_SIZE(mcp3201_channels),
.resolution = 21,
/* 2% max deviation + 144 clock periods to exit shutdown */
.conv_time = 80000 * 1.02 + 144000 / 102.4,
},
[mcp3550_60] = {
.channels = mcp3201_channels,
.num_channels = ARRAY_SIZE(mcp3201_channels),
.resolution = 21,
.conv_time = 66670 * 1.02 + 144000 / 122.88,
},
[mcp3551] = {
.channels = mcp3201_channels,
.num_channels = ARRAY_SIZE(mcp3201_channels),
.resolution = 21,
.conv_time = 73100 * 1.02 + 144000 / 112.64,
},
[mcp3553] = {
.channels = mcp3201_channels,
.num_channels = ARRAY_SIZE(mcp3201_channels),
.resolution = 21,
.conv_time = 16670 * 1.02 + 144000 / 122.88,
},
};
static int mcp320x_probe(struct spi_device *spi)
@ -304,7 +378,7 @@ static int mcp320x_probe(struct spi_device *spi)
struct iio_dev *indio_dev;
struct mcp320x *adc;
const struct mcp320x_chip_info *chip_info;
int ret;
int ret, device_index;
indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*adc));
if (!indio_dev)
@ -320,7 +394,8 @@ static int mcp320x_probe(struct spi_device *spi)
indio_dev->info = &mcp320x_info;
spi_set_drvdata(spi, indio_dev);
chip_info = &mcp320x_chip_infos[spi_get_device_id(spi)->driver_data];
device_index = spi_get_device_id(spi)->driver_data;
chip_info = &mcp320x_chip_infos[device_index];
indio_dev->channels = chip_info->channels;
indio_dev->num_channels = chip_info->num_channels;
@ -329,7 +404,8 @@ static int mcp320x_probe(struct spi_device *spi)
adc->transfer[0].tx_buf = &adc->tx_buf;
adc->transfer[0].len = sizeof(adc->tx_buf);
adc->transfer[1].rx_buf = adc->rx_buf;
adc->transfer[1].len = sizeof(adc->rx_buf);
adc->transfer[1].len = DIV_ROUND_UP(chip_info->resolution, 8);
if (chip_info->num_channels == 1)
/* single-channel converters are rx only (no MOSI pin) */
spi_message_init_with_transfers(&adc->msg,
@ -338,6 +414,32 @@ static int mcp320x_probe(struct spi_device *spi)
spi_message_init_with_transfers(&adc->msg, adc->transfer,
ARRAY_SIZE(adc->transfer));
switch (device_index) {
case mcp3550_50:
case mcp3550_60:
case mcp3551:
case mcp3553:
/* rx len increases from 24 to 25 bit in SPI mode 0,0 */
if (!(spi->mode & SPI_CPOL))
adc->transfer[1].len++;
/* conversions are started by asserting CS pin for 8 usec */
adc->start_conv_transfer.delay_usecs = 8;
spi_message_init_with_transfers(&adc->start_conv_msg,
&adc->start_conv_transfer, 1);
/*
* If CS was previously kept low (continuous conversion mode)
* and then changed to high, the chip is in shutdown.
* Sometimes it fails to wake from shutdown and clocks out
* only 0xffffff. The magic sequence of performing two
* conversions without delay between them resets the chip
* and ensures all subsequent conversions succeed.
*/
mcp320x_adc_conversion(adc, 0, 1, device_index, &ret);
mcp320x_adc_conversion(adc, 0, 1, device_index, &ret);
}
adc->reg = devm_regulator_get(&spi->dev, "vref");
if (IS_ERR(adc->reg))
return PTR_ERR(adc->reg);
@ -392,6 +494,10 @@ static const struct of_device_id mcp320x_dt_ids[] = {
{ .compatible = "microchip,mcp3204" },
{ .compatible = "microchip,mcp3208" },
{ .compatible = "microchip,mcp3301" },
{ .compatible = "microchip,mcp3550-50" },
{ .compatible = "microchip,mcp3550-60" },
{ .compatible = "microchip,mcp3551" },
{ .compatible = "microchip,mcp3553" },
{ }
};
MODULE_DEVICE_TABLE(of, mcp320x_dt_ids);
@ -407,6 +513,10 @@ static const struct spi_device_id mcp320x_id[] = {
{ "mcp3204", mcp3204 },
{ "mcp3208", mcp3208 },
{ "mcp3301", mcp3301 },
{ "mcp3550-50", mcp3550_50 },
{ "mcp3550-60", mcp3550_60 },
{ "mcp3551", mcp3551 },
{ "mcp3553", mcp3553 },
{ }
};
MODULE_DEVICE_TABLE(spi, mcp320x_id);
@ -423,5 +533,5 @@ static struct spi_driver mcp320x_driver = {
module_spi_driver(mcp320x_driver);
MODULE_AUTHOR("Oskar Andero <oskar.andero@gmail.com>");
MODULE_DESCRIPTION("Microchip Technology MCP3x01/02/04/08");
MODULE_DESCRIPTION("Microchip Technology MCP3x01/02/04/08 and MCP3550/1/3");
MODULE_LICENSE("GPL v2");