diff --git a/drivers/pci/controller/pci-hyperv.c b/drivers/pci/controller/pci-hyperv.c
index 40b625458afa..57adeca7bda9 100644
--- a/drivers/pci/controller/pci-hyperv.c
+++ b/drivers/pci/controller/pci-hyperv.c
@@ -365,6 +365,39 @@ struct pci_delete_interrupt {
 	struct tran_int_desc int_desc;
 } __packed;
 
+/*
+ * Note: the VM must pass a valid block id, wslot and bytes_requested.
+ */
+struct pci_read_block {
+	struct pci_message message_type;
+	u32 block_id;
+	union win_slot_encoding wslot;
+	u32 bytes_requested;
+} __packed;
+
+struct pci_read_block_response {
+	struct vmpacket_descriptor hdr;
+	u32 status;
+	u8 bytes[HV_CONFIG_BLOCK_SIZE_MAX];
+} __packed;
+
+/*
+ * Note: the VM must pass a valid block id, wslot and byte_count.
+ */
+struct pci_write_block {
+	struct pci_message message_type;
+	u32 block_id;
+	union win_slot_encoding wslot;
+	u32 byte_count;
+	u8 bytes[HV_CONFIG_BLOCK_SIZE_MAX];
+} __packed;
+
+struct pci_dev_inval_block {
+	struct pci_incoming_message incoming;
+	union win_slot_encoding wslot;
+	u64 block_mask;
+} __packed;
+
 struct pci_dev_incoming {
 	struct pci_incoming_message incoming;
 	union win_slot_encoding wslot;
@@ -499,6 +532,9 @@ struct hv_pci_dev {
 	struct hv_pcibus_device *hbus;
 	struct work_struct wrk;
 
+	void (*block_invalidate)(void *context, u64 block_mask);
+	void *invalidate_context;
+
 	/*
 	 * What would be observed if one wrote 0xFFFFFFFF to a BAR and then
 	 * read it back, for each of the BAR offsets within config space.
@@ -817,6 +853,256 @@ static struct pci_ops hv_pcifront_ops = {
 	.write = hv_pcifront_write_config,
 };
 
+/*
+ * Paravirtual backchannel
+ *
+ * Hyper-V SR-IOV provides a backchannel mechanism in software for
+ * communication between a VF driver and a PF driver.  These
+ * "configuration blocks" are similar in concept to PCI configuration space,
+ * but instead of doing reads and writes in 32-bit chunks through a very slow
+ * path, packets of up to 128 bytes can be sent or received asynchronously.
+ *
+ * Nearly every SR-IOV device contains just such a communications channel in
+ * hardware, so using this one in software is usually optional.  Using the
+ * software channel, however, allows driver implementers to leverage software
+ * tools that fuzz the communications channel looking for vulnerabilities.
+ *
+ * The usage model for these packets puts the responsibility for reading or
+ * writing on the VF driver.  The VF driver sends a read or a write packet,
+ * indicating which "block" is being referred to by number.
+ *
+ * If the PF driver wishes to initiate communication, it can "invalidate" one or
+ * more of the first 64 blocks.  This invalidation is delivered via a callback
+ * supplied by the VF driver by this driver.
+ *
+ * No protocol is implied, except that supplied by the PF and VF drivers.
+ */
+
+struct hv_read_config_compl {
+	struct hv_pci_compl comp_pkt;
+	void *buf;
+	unsigned int len;
+	unsigned int bytes_returned;
+};
+
+/**
+ * hv_pci_read_config_compl() - Invoked when a response packet
+ * for a read config block operation arrives.
+ * @context:		Identifies the read config operation
+ * @resp:		The response packet itself
+ * @resp_packet_size:	Size in bytes of the response packet
+ */
+static void hv_pci_read_config_compl(void *context, struct pci_response *resp,
+				     int resp_packet_size)
+{
+	struct hv_read_config_compl *comp = context;
+	struct pci_read_block_response *read_resp =
+		(struct pci_read_block_response *)resp;
+	unsigned int data_len, hdr_len;
+
+	hdr_len = offsetof(struct pci_read_block_response, bytes);
+	if (resp_packet_size < hdr_len) {
+		comp->comp_pkt.completion_status = -1;
+		goto out;
+	}
+
+	data_len = resp_packet_size - hdr_len;
+	if (data_len > 0 && read_resp->status == 0) {
+		comp->bytes_returned = min(comp->len, data_len);
+		memcpy(comp->buf, read_resp->bytes, comp->bytes_returned);
+	} else {
+		comp->bytes_returned = 0;
+	}
+
+	comp->comp_pkt.completion_status = read_resp->status;
+out:
+	complete(&comp->comp_pkt.host_event);
+}
+
+/**
+ * hv_read_config_block() - Sends a read config block request to
+ * the back-end driver running in the Hyper-V parent partition.
+ * @pdev:		The PCI driver's representation for this device.
+ * @buf:		Buffer into which the config block will be copied.
+ * @len:		Size in bytes of buf.
+ * @block_id:		Identifies the config block which has been requested.
+ * @bytes_returned:	Size which came back from the back-end driver.
+ *
+ * Return: 0 on success, -errno on failure
+ */
+int hv_read_config_block(struct pci_dev *pdev, void *buf, unsigned int len,
+			 unsigned int block_id, unsigned int *bytes_returned)
+{
+	struct hv_pcibus_device *hbus =
+		container_of(pdev->bus->sysdata, struct hv_pcibus_device,
+			     sysdata);
+	struct {
+		struct pci_packet pkt;
+		char buf[sizeof(struct pci_read_block)];
+	} pkt;
+	struct hv_read_config_compl comp_pkt;
+	struct pci_read_block *read_blk;
+	int ret;
+
+	if (len == 0 || len > HV_CONFIG_BLOCK_SIZE_MAX)
+		return -EINVAL;
+
+	init_completion(&comp_pkt.comp_pkt.host_event);
+	comp_pkt.buf = buf;
+	comp_pkt.len = len;
+
+	memset(&pkt, 0, sizeof(pkt));
+	pkt.pkt.completion_func = hv_pci_read_config_compl;
+	pkt.pkt.compl_ctxt = &comp_pkt;
+	read_blk = (struct pci_read_block *)&pkt.pkt.message;
+	read_blk->message_type.type = PCI_READ_BLOCK;
+	read_blk->wslot.slot = devfn_to_wslot(pdev->devfn);
+	read_blk->block_id = block_id;
+	read_blk->bytes_requested = len;
+
+	ret = vmbus_sendpacket(hbus->hdev->channel, read_blk,
+			       sizeof(*read_blk), (unsigned long)&pkt.pkt,
+			       VM_PKT_DATA_INBAND,
+			       VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED);
+	if (ret)
+		return ret;
+
+	ret = wait_for_response(hbus->hdev, &comp_pkt.comp_pkt.host_event);
+	if (ret)
+		return ret;
+
+	if (comp_pkt.comp_pkt.completion_status != 0 ||
+	    comp_pkt.bytes_returned == 0) {
+		dev_err(&hbus->hdev->device,
+			"Read Config Block failed: 0x%x, bytes_returned=%d\n",
+			comp_pkt.comp_pkt.completion_status,
+			comp_pkt.bytes_returned);
+		return -EIO;
+	}
+
+	*bytes_returned = comp_pkt.bytes_returned;
+	return 0;
+}
+EXPORT_SYMBOL(hv_read_config_block);
+
+/**
+ * hv_pci_write_config_compl() - Invoked when a response packet for a write
+ * config block operation arrives.
+ * @context:		Identifies the write config operation
+ * @resp:		The response packet itself
+ * @resp_packet_size:	Size in bytes of the response packet
+ */
+static void hv_pci_write_config_compl(void *context, struct pci_response *resp,
+				      int resp_packet_size)
+{
+	struct hv_pci_compl *comp_pkt = context;
+
+	comp_pkt->completion_status = resp->status;
+	complete(&comp_pkt->host_event);
+}
+
+/**
+ * hv_write_config_block() - Sends a write config block request to the
+ * back-end driver running in the Hyper-V parent partition.
+ * @pdev:		The PCI driver's representation for this device.
+ * @buf:		Buffer from which the config block will	be copied.
+ * @len:		Size in bytes of buf.
+ * @block_id:		Identifies the config block which is being written.
+ *
+ * Return: 0 on success, -errno on failure
+ */
+int hv_write_config_block(struct pci_dev *pdev, void *buf, unsigned int len,
+			  unsigned int block_id)
+{
+	struct hv_pcibus_device *hbus =
+		container_of(pdev->bus->sysdata, struct hv_pcibus_device,
+			     sysdata);
+	struct {
+		struct pci_packet pkt;
+		char buf[sizeof(struct pci_write_block)];
+		u32 reserved;
+	} pkt;
+	struct hv_pci_compl comp_pkt;
+	struct pci_write_block *write_blk;
+	u32 pkt_size;
+	int ret;
+
+	if (len == 0 || len > HV_CONFIG_BLOCK_SIZE_MAX)
+		return -EINVAL;
+
+	init_completion(&comp_pkt.host_event);
+
+	memset(&pkt, 0, sizeof(pkt));
+	pkt.pkt.completion_func = hv_pci_write_config_compl;
+	pkt.pkt.compl_ctxt = &comp_pkt;
+	write_blk = (struct pci_write_block *)&pkt.pkt.message;
+	write_blk->message_type.type = PCI_WRITE_BLOCK;
+	write_blk->wslot.slot = devfn_to_wslot(pdev->devfn);
+	write_blk->block_id = block_id;
+	write_blk->byte_count = len;
+	memcpy(write_blk->bytes, buf, len);
+	pkt_size = offsetof(struct pci_write_block, bytes) + len;
+	/*
+	 * This quirk is required on some hosts shipped around 2018, because
+	 * these hosts don't check the pkt_size correctly (new hosts have been
+	 * fixed since early 2019). The quirk is also safe on very old hosts
+	 * and new hosts, because, on them, what really matters is the length
+	 * specified in write_blk->byte_count.
+	 */
+	pkt_size += sizeof(pkt.reserved);
+
+	ret = vmbus_sendpacket(hbus->hdev->channel, write_blk, pkt_size,
+			       (unsigned long)&pkt.pkt, VM_PKT_DATA_INBAND,
+			       VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED);
+	if (ret)
+		return ret;
+
+	ret = wait_for_response(hbus->hdev, &comp_pkt.host_event);
+	if (ret)
+		return ret;
+
+	if (comp_pkt.completion_status != 0) {
+		dev_err(&hbus->hdev->device,
+			"Write Config Block failed: 0x%x\n",
+			comp_pkt.completion_status);
+		return -EIO;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(hv_write_config_block);
+
+/**
+ * hv_register_block_invalidate() - Invoked when a config block invalidation
+ * arrives from the back-end driver.
+ * @pdev:		The PCI driver's representation for this device.
+ * @context:		Identifies the device.
+ * @block_invalidate:	Identifies all of the blocks being invalidated.
+ *
+ * Return: 0 on success, -errno on failure
+ */
+int hv_register_block_invalidate(struct pci_dev *pdev, void *context,
+				 void (*block_invalidate)(void *context,
+							  u64 block_mask))
+{
+	struct hv_pcibus_device *hbus =
+		container_of(pdev->bus->sysdata, struct hv_pcibus_device,
+			     sysdata);
+	struct hv_pci_dev *hpdev;
+
+	hpdev = get_pcichild_wslot(hbus, devfn_to_wslot(pdev->devfn));
+	if (!hpdev)
+		return -ENODEV;
+
+	hpdev->block_invalidate = block_invalidate;
+	hpdev->invalidate_context = context;
+
+	put_pcichild(hpdev);
+	return 0;
+
+}
+EXPORT_SYMBOL(hv_register_block_invalidate);
+
 /* Interrupt management hooks */
 static void hv_int_desc_free(struct hv_pci_dev *hpdev,
 			     struct tran_int_desc *int_desc)
@@ -1968,6 +2254,7 @@ static void hv_pci_onchannelcallback(void *context)
 	struct pci_response *response;
 	struct pci_incoming_message *new_message;
 	struct pci_bus_relations *bus_rel;
+	struct pci_dev_inval_block *inval;
 	struct pci_dev_incoming *dev_message;
 	struct hv_pci_dev *hpdev;
 
@@ -2045,6 +2332,21 @@ static void hv_pci_onchannelcallback(void *context)
 				}
 				break;
 
+			case PCI_INVALIDATE_BLOCK:
+
+				inval = (struct pci_dev_inval_block *)buffer;
+				hpdev = get_pcichild_wslot(hbus,
+							   inval->wslot.slot);
+				if (hpdev) {
+					if (hpdev->block_invalidate) {
+						hpdev->block_invalidate(
+						    hpdev->invalidate_context,
+						    inval->block_mask);
+					}
+					put_pcichild(hpdev);
+				}
+				break;
+
 			default:
 				dev_warn(&hbus->hdev->device,
 					"Unimplemented protocol message %x\n",
diff --git a/include/linux/hyperv.h b/include/linux/hyperv.h
index 6256cc34c4a6..9d37f8cf1245 100644
--- a/include/linux/hyperv.h
+++ b/include/linux/hyperv.h
@@ -1578,4 +1578,19 @@ hv_pkt_iter_next(struct vmbus_channel *channel,
 	for (pkt = hv_pkt_iter_first(channel); pkt; \
 	    pkt = hv_pkt_iter_next(channel, pkt))
 
+/*
+ * Functions for passing data between SR-IOV PF and VF drivers.  The VF driver
+ * sends requests to read and write blocks. Each block must be 128 bytes or
+ * smaller. Optionally, the VF driver can register a callback function which
+ * will be invoked when the host says that one or more of the first 64 block
+ * IDs is "invalid" which means that the VF driver should reread them.
+ */
+#define HV_CONFIG_BLOCK_SIZE_MAX 128
+int hv_read_config_block(struct pci_dev *dev, void *buf, unsigned int buf_len,
+			 unsigned int block_id, unsigned int *bytes_returned);
+int hv_write_config_block(struct pci_dev *dev, void *buf, unsigned int len,
+			  unsigned int block_id);
+int hv_register_block_invalidate(struct pci_dev *dev, void *context,
+				 void (*block_invalidate)(void *context,
+							  u64 block_mask));
 #endif /* _HYPERV_H */