openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity

STM32 DT updates for v5.3, round 1 

Highlights:
 ----------
 
  - Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
    board. It is based on stm32mp157c SoC.
  - Add OTG full support on stm32mp15.
  - Fix issues seen during yaml validation on stpmic and stmfx.
  - Add i2c power/wakeup support on stm32mp15.
  - Add card detect on sdcard on stm32mp boards
 -----BEGIN PGP SIGNATURE-----
 
 iQJMBAABCgA2FiEEctl9+nxzUSUqdELdf5rJavIecIUFAl5rsncYHGFsZXhhbmRy
 ZS50b3JndWVAc3QuY29tAAoJEH+ayWryHnCFr7YP/2zLfZfd7gywA/AvrqeBkd7Y
 5GiJ7gQ1RXyAaF0a0kUZLrh2Qx8/sjnIPlyQG63waIS7lrgeVQC6i6TEOjpXNfbn
 m6ZhDpdm0J0LCgJSawrYw14YeqRdrkkyr96QuMYZN54E/NaQvPzfkOFLaQB/HREy
 +iT1TNs+A3Xtw2zeXh0PCuFRyjg2TvCeae8OV8aa0kqeKzv8aNBw28pV3r0ZkiGT
 Cti7E+uxG9S9BsHIr2k9PagGWvYJ4w6fiJVyCd1oG1oPwY1wwhnaijdTJE7H94XO
 6wajE9WiVMTKMxvzqH1aZ7CIZiRCHlQpQ/CHfBjY1pcdG+IEh6d4cWamSDCk2BEu
 V/flJl70rubbjOMdCnJGqIvUjSaLAm+197MbdIHOJT4SoDhwmWWHVuedZ4wG4k3F
 NCNL2el4cmsiSpNZfanvGPd3ZWegy9LoISlUomZtdLFk4vmuJVFM+tYCeSKQyBMb
 /kSU08fV2uh8VNXdNZoBEsOpgcw/3xQcPkKzp/q/u4h8FwppsozogfQddiqBQ8JB
 an/6r2T/UW/ajPDybeSkV8YVdRq/jdgUaqlQZfIcPyxvsnI36ZQzq0jB8IpRTagZ
 dpzbuI3pJQ0FjU5fXrUcoTDGJIrru6CmT6kQIyjxu97Oo7BrscrSZCrj/NWlOEyq
 1zmEP/9PL2jXOfVEFHNO
 =89XF
 -----END PGP SIGNATURE-----

Merge tag 'stm32-dt-for-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT updates for v5.3, round 1

Highlights:
----------

 - Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
   board. It is based on stm32mp157c SoC.
 - Add OTG full support on stm32mp15.
 - Fix issues seen during yaml validation on stpmic and stmfx.
 - Add i2c power/wakeup support on stm32mp15.
 - Add card detect on sdcard on stm32mp boards

* tag 'stm32-dt-for-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (25 commits)
  ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
  ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
  ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
  ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
  ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
  ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
  ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
  ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
  ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
  ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
  ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
  ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
  ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
  ARM: dts: stm32: Correct stmfx node name on stm32746g-eval board
  ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
  ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
  ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
  ARM: dts: stm32: add USB OTG full support on stm32mp151
  ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
  ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board
  ...

Link: https://lore.kernel.org/r/ded09d01-df47-9572-4679-34669bff8916@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This commit is contained in:
Arnd Bergmann 2020-03-25 21:45:02 +01:00
parent 25876536ae 431c89e6f3
commit ead993983f
11 changed files with 769 additions and 27 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

1
arch/arm/boot/dts/Makefile
View File

@ -1016,6 +1016,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32h743i-disco.dtb \
stm32mp157a-avenger96.dtb \
stm32mp157a-dk1.dtb \
stm32mp157c-dhcom-pdk2.dtb \
stm32mp157c-dk2.dtb \
stm32mp157c-ed1.dtb \
stm32mp157c-ev1.dtb

2
arch/arm/boot/dts/stm32746g-eval.dts
View File

@ -165,7 +165,7 @@ stmfx: stmfx@42 {
interrupts = <8 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&gpioi>;
stmfx_pinctrl: stmfx-pin-controller {
stmfx_pinctrl: pinctrl {
compatible = "st,stmfx-0300-pinctrl";
gpio-controller;
#gpio-cells = <2>;

93
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
View File

@ -162,6 +162,40 @@ pins1 {
};
};
ethernet0_rmii_pins_a: rmii-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
<STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
<STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
<STM32_PINMUX('A', 1, AF0)>, /* ETH1_RMII_REF_CLK */
<STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */
<STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */
bias-disable;
drive-push-pull;
slew-rate = <2>;
};
pins2 {
pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */
<STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */
<STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */
bias-disable;
};
};
ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
<STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
<STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
<STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */
<STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */
<STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */
<STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */
<STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */
<STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */
};
};
fmc_pins_a: fmc-0 {
pins1 {
pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
@ -685,6 +719,26 @@ pins {
};
};
sai2a_pins_b: sai2a-2 {
pins1 {
pinmux = <STM32_PINMUX('I', 6, AF10)>, /* SAI2_SD_A */
<STM32_PINMUX('I', 7, AF10)>, /* SAI2_FS_A */
<STM32_PINMUX('D', 13, AF10)>; /* SAI2_SCK_A */
slew-rate = <0>;
drive-push-pull;
bias-disable;
};
};
sai2a_sleep_pins_b: sai2a-sleep-3 {
pins {
pinmux = <STM32_PINMUX('I', 6, ANALOG)>, /* SAI2_SD_A */
<STM32_PINMUX('I', 7, ANALOG)>, /* SAI2_FS_A */
<STM32_PINMUX('D', 13, ANALOG)>; /* SAI2_SCK_A */
};
};
sai2b_pins_a: sai2b-0 {
pins1 {
pinmux = <STM32_PINMUX('E', 12, AF10)>, /* SAI2_SCK_B */
@ -1000,6 +1054,19 @@ pins {
};
};
usart3_pins_a: usart3-0 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
bias-disable;
drive-push-pull;
slew-rate = <0>;
};
pins2 {
pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
bias-disable;
};
};
uart4_pins_a: uart4-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
@ -1040,6 +1107,32 @@ pins2 {
bias-disable;
};
};
uart8_pins_a: uart8-0 {
pins1 {
pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
bias-disable;
drive-push-pull;
slew-rate = <0>;
};
pins2 {
pinmux = <STM32_PINMUX('E', 0, AF8)>; /* UART8_RX */
bias-disable;
};
};
usbotg_hs_pins_a: usbotg-hs-0 {
pins {
pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
};
};
usbotg_fs_dp_dm_pins_a: usbotg-fs-dp-dm-0 {
pins {
pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* OTG_FS_DM */
<STM32_PINMUX('A', 12, ANALOG)>; /* OTG_FS_DP */
};
};
};
&pinctrl_z {

16
arch/arm/boot/dts/stm32mp151.dtsi
View File

@ -17,6 +17,7 @@ cpus {
cpu0: cpu@0 {
compatible = "arm,cortex-a7";
clock-frequency = <650000000>;
device_type = "cpu";
reg = <0>;
};
@ -483,6 +484,7 @@ i2c1: i2c@40012000 {
resets = <&rcc I2C1_R>;
#address-cells = <1>;
#size-cells = <0>;
wakeup-source;
status = "disabled";
};
@ -496,6 +498,7 @@ i2c2: i2c@40013000 {
resets = <&rcc I2C2_R>;
#address-cells = <1>;
#size-cells = <0>;
wakeup-source;
status = "disabled";
};
@ -509,6 +512,7 @@ i2c3: i2c@40014000 {
resets = <&rcc I2C3_R>;
#address-cells = <1>;
#size-cells = <0>;
wakeup-source;
status = "disabled";
};
@ -522,6 +526,7 @@ i2c5: i2c@40015000 {
resets = <&rcc I2C5_R>;
#address-cells = <1>;
#size-cells = <0>;
wakeup-source;
status = "disabled";
};
@ -959,6 +964,7 @@ dma1: dma-controller@48000000 {
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA1>;
resets = <&rcc DMA1_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
@ -976,6 +982,7 @@ dma2: dma-controller@48001000 {
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA2>;
resets = <&rcc DMA2_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
@ -989,6 +996,7 @@ dmamux1: dma-router@48002000 {
dma-masters = <&dma1 &dma2>;
dma-channels = <16>;
clocks = <&rcc DMAMUX>;
resets = <&rcc DMAMUX_R>;
};
adc: adc@48003000 {
@ -1044,7 +1052,7 @@ sdmmc3: sdmmc@48004000 {
};
usbotg_hs: usb-otg@49000000 {
compatible = "snps,dwc2";
compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
clocks = <&rcc USBO_K>;
clock-names = "otg";
@ -1055,6 +1063,7 @@ usbotg_hs: usb-otg@49000000 {
g-np-tx-fifo-size = <32>;
g-tx-fifo-size = <128 128 64 64 64 64 32 32>;
dr_mode = "otg";
usb33d-supply = <&usb33>;
status = "disabled";
};
@ -1280,6 +1289,7 @@ mdma1: dma-controller@58000000 {
reg = <0x58000000 0x1000>;
interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc MDMA>;
resets = <&rcc MDMA_R>;
#dma-cells = <5>;
dma-channels = <32>;
dma-requests = <48>;
@ -1369,10 +1379,12 @@ ethernet0: ethernet@5800a000 {
clock-names = "stmmaceth",
"mac-clk-tx",
"mac-clk-rx",
"eth-ck",
"ethstp";
clocks = <&rcc ETHMAC>,
<&rcc ETHTX>,
<&rcc ETHRX>,
<&rcc ETHCK_K>,
<&rcc ETHSTP>;
st,syscon = <&syscfg 0x4>;
snps,mixed-burst;
@ -1473,6 +1485,7 @@ i2c4: i2c@5c002000 {
resets = <&rcc I2C4_R>;
#address-cells = <1>;
#size-cells = <0>;
wakeup-source;
status = "disabled";
};
@ -1508,6 +1521,7 @@ i2c6: i2c@5c009000 {
resets = <&rcc I2C6_R>;
#address-cells = <1>;
#size-cells = <0>;
wakeup-source;
status = "disabled";
};

1
arch/arm/boot/dts/stm32mp153.dtsi
View File

@ -10,6 +10,7 @@ / {
cpus {
cpu1: cpu@1 {
compatible = "arm,cortex-a7";
clock-frequency = <650000000>;
device_type = "cpu";
reg = <1>;
};

11
arch/arm/boot/dts/stm32mp157a-avenger96.dts
View File

@ -135,10 +135,6 @@ pmic: stpmic@33 {
#interrupt-cells = <2>;
status = "okay";
st,main-control-register = <0x04>;
st,vin-control-register = <0xc0>;
st,usb-control-register = <0x30>;
regulators {
compatible = "st,stpmic1-regulators";
@ -173,7 +169,6 @@ vdd: buck3 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
st,mask_reset;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
@ -213,8 +208,6 @@ vtt_ddr: ldo3 {
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
interrupt-parent = <&pmic>;
};
@ -240,7 +233,6 @@ v1v8: ldo6 {
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
regulator-over-current-protection;
};
bst_out: boost {
@ -300,7 +292,8 @@ &sdmmc1 {
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
broken-cd;
cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
disable-wp;
st,sig-dir;
st,neg-edge;
st,use-ckin;

265
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts Normal file
View File

@ -0,0 +1,265 @@
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
* Copyright (C) 2019 Marek Vasut <marex@denx.de>
*/
#include "stm32mp157c-dhcom-som.dtsi"
#include <dt-bindings/pwm/pwm.h>
/ {
model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)";
compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
aliases {
serial0 = &uart4;
serial1 = &usart3;
serial2 = &uart8;
ethernet0 = &ethernet0;
};
chosen {
stdout-path = "serial0:115200n8";
};
clk_ext_audio_codec: clock-codec {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
};
display_bl: display-bl {
compatible = "pwm-backlight";
pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
default-brightness-level = <8>;
enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
status = "okay";
};
ethernet_vio: vioregulator {
compatible = "regulator-fixed";
regulator-name = "vio";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
regulator-always-on;
regulator-boot-on;
};
panel {
compatible = "edt,etm0700g0edh6";
backlight = <&display_bl>;
port {
lcd_panel_in: endpoint {
remote-endpoint = <&lcd_display_out>;
};
};
};
sound {
compatible = "audio-graph-card";
routing =
"MIC_IN", "Capture",
"Capture", "Mic Bias",
"Playback", "HP_OUT";
dais = <&sai2a_port &sai2b_port>;
status = "okay";
};
};
&cec {
pinctrl-names = "default";
pinctrl-0 = <&cec_pins_a>;
status = "okay";
};
&ethernet0 {
status = "okay";
pinctrl-0 = <&ethernet0_rmii_pins_a>;
pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
pinctrl-names = "default", "sleep";
phy-mode = "rmii";
max-speed = <100>;
phy-handle = <&phy0>;
st,eth-ref-clk-sel;
phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy0: ethernet-phy@1 {
reg = <1>;
};
};
};
&i2c5 {
pinctrl-names = "default";
pinctrl-0 = <&i2c5_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
sgtl5000: codec@a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
#sound-dai-cells = <0>;
clocks = <&clk_ext_audio_codec>;
VDDA-supply = <&v3v3>;
VDDIO-supply = <&vdd>;
sgtl5000_port: port {
#address-cells = <1>;
#size-cells = <0>;
sgtl5000_tx_endpoint: endpoint@0 {
reg = <0>;
remote-endpoint = <&sai2a_endpoint>;
frame-master;
bitclock-master;
};
sgtl5000_rx_endpoint: endpoint@1 {
reg = <1>;
remote-endpoint = <&sai2b_endpoint>;
frame-master;
bitclock-master;
};
};
};
polytouch@38 {
compatible = "edt,edt-ft5x06";
reg = <0x38>;
interrupt-parent = <&gpiog>;
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
linux,wakeup;
};
};
&ltdc {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&ltdc_pins_b>;
pinctrl-1 = <&ltdc_pins_sleep_b>;
status = "okay";
port {
lcd_display_out: endpoint {
remote-endpoint = <&lcd_panel_in>;
};
};
};
&m_can1 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&m_can1_pins_a>;
pinctrl-1 = <&m_can1_sleep_pins_a>;
status = "okay";
};
&sai2 {
clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
clock-names = "pclk", "x8k", "x11k";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
status = "okay";
sai2a: audio-controller@4400b004 {
#clock-cells = <0>;
dma-names = "tx";
clocks = <&rcc SAI2_K>;
clock-names = "sai_ck";
status = "okay";
sai2a_port: port {
sai2a_endpoint: endpoint {
remote-endpoint = <&sgtl5000_tx_endpoint>;
format = "i2s";
mclk-fs = <512>;
dai-tdm-slot-num = <2>;
dai-tdm-slot-width = <16>;
};
};
};
sai2b: audio-controller@4400b024 {
dma-names = "rx";
st,sync = <&sai2a 2>;
clocks = <&rcc SAI2_K>, <&sai2a>;
clock-names = "sai_ck", "MCLK";
status = "okay";
sai2b_port: port {
sai2b_endpoint: endpoint {
remote-endpoint = <&sgtl5000_rx_endpoint>;
format = "i2s";
mclk-fs = <512>;
dai-tdm-slot-num = <2>;
dai-tdm-slot-width = <16>;
};
};
};
};
&timers2 {
/* spare dmas for other usage (un-delete to enable pwm capture) */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
pwm2: pwm {
pinctrl-0 = <&pwm2_pins_a>;
pinctrl-names = "default";
status = "okay";
};
timer@1 {
status = "okay";
};
};
&usart3 {
pinctrl-names = "default";
pinctrl-0 = <&usart3_pins_a>;
status = "okay";
};
&uart8 {
pinctrl-names = "default";
pinctrl-0 = <&uart8_pins_a>;
status = "okay";
};
&usbh_ehci {
phys = <&usbphyc_port0>;
status = "okay";
};
&usbotg_hs {
dr_mode = "peripheral";
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";
};
&usbphyc {
status = "okay";
};
&usbphyc_port0 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
};
&usbphyc_port1 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
};

368
arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi Normal file
View File

@ -0,0 +1,368 @@
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) 2019 Marek Vasut <marex@denx.de>
*/
/dts-v1/;
#include "stm32mp157.dtsi"
#include "stm32mp15xc.dtsi"
#include "stm32mp15-pinctrl.dtsi"
#include "stm32mp15xxaa-pinctrl.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/mfd/st,stpmic1.h>
/ {
memory@c0000000 {
device_type = "memory";
reg = <0xC0000000 0x40000000>;
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
mcuram2: mcuram2@10000000 {
compatible = "shared-dma-pool";
reg = <0x10000000 0x40000>;
no-map;
};
vdev0vring0: vdev0vring0@10040000 {
compatible = "shared-dma-pool";
reg = <0x10040000 0x1000>;
no-map;
};
vdev0vring1: vdev0vring1@10041000 {
compatible = "shared-dma-pool";
reg = <0x10041000 0x1000>;
no-map;
};
vdev0buffer: vdev0buffer@10042000 {
compatible = "shared-dma-pool";
reg = <0x10042000 0x4000>;
no-map;
};
mcuram: mcuram@30000000 {
compatible = "shared-dma-pool";
reg = <0x30000000 0x40000>;
no-map;
};
retram: retram@38000000 {
compatible = "shared-dma-pool";
reg = <0x38000000 0x10000>;
no-map;
};
};
};
&adc {
vdd-supply = <&vdd>;
vdda-supply = <&vdda>;
vref-supply = <&vdda>;
status = "okay";
adc1: adc@0 {
st,min-sample-time-nsecs = <5000>;
st,adc-channels = <0>;
status = "okay";
};
adc2: adc@100 {
st,adc-channels = <1>;
st,min-sample-time-nsecs = <5000>;
status = "okay";
};
};
&dac {
pinctrl-names = "default";
pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
vref-supply = <&vdda>;
status = "okay";
dac1: dac@1 {
status = "okay";
};
dac2: dac@2 {
status = "okay";
};
};
&dts {
status = "okay";
};
&gpu {
status = "okay";
};
&i2c4 {
pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
rtc@32 {
compatible = "microcrystal,rv8803";
reg = <0x32>;
};
pmic: stpmic@33 {
compatible = "st,stpmic1";
reg = <0x33>;
interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
status = "okay";
regulators {
compatible = "st,stpmic1-regulators";
ldo1-supply = <&v3v3>;
ldo2-supply = <&v3v3>;
ldo3-supply = <&vdd_ddr>;
ldo5-supply = <&v3v3>;
ldo6-supply = <&v3v3>;
pwr_sw1-supply = <&bst_out>;
pwr_sw2-supply = <&bst_out>;
vddcore: buck1 {
regulator-name = "vddcore";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
vdd_ddr: buck2 {
regulator-name = "vdd_ddr";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
vdd: buck3 {
regulator-name = "vdd";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
st,mask-reset;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
v3v3: buck4 {
regulator-name = "v3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-over-current-protection;
regulator-initial-mode = <0>;
};
vdda: ldo1 {
regulator-name = "vdda";
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
interrupts = <IT_CURLIM_LDO1 0>;
};
v2v8: ldo2 {
regulator-name = "v2v8";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
interrupts = <IT_CURLIM_LDO2 0>;
};
vtt_ddr: ldo3 {
regulator-name = "vtt_ddr";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <750000>;
regulator-always-on;
regulator-over-current-protection;
};
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
};
vdd_sd: ldo5 {
regulator-name = "vdd_sd";
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
interrupts = <IT_CURLIM_LDO5 0>;
regulator-boot-on;
};
v1v8: ldo6 {
regulator-name = "v1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
interrupts = <IT_CURLIM_LDO6 0>;
};
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
regulator-over-current-protection;
};
bst_out: boost {
regulator-name = "bst_out";
interrupts = <IT_OCP_BOOST 0>;
};
vbus_otg: pwr_sw1 {
regulator-name = "vbus_otg";
interrupts = <IT_OCP_OTG 0>;
};
vbus_sw: pwr_sw2 {
regulator-name = "vbus_sw";
interrupts = <IT_OCP_SWOUT 0>;
regulator-active-discharge;
};
};
onkey {
compatible = "st,stpmic1-onkey";
interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
interrupt-names = "onkey-falling", "onkey-rising";
power-off-time-sec = <10>;
status = "okay";
};
watchdog {
compatible = "st,stpmic1-wdt";
status = "disabled";
};
};
touchscreen@49 {
compatible = "ti,tsc2004";
reg = <0x49>;
vio-supply = <&v3v3>;
interrupts-extended = <&gpioh 3 IRQ_TYPE_EDGE_FALLING>;
};
eeprom@50 {
compatible = "atmel,24c02";
reg = <0x50>;
pagesize = <16>;
};
};
&ipcc {
status = "okay";
};
&iwdg2 {
timeout-sec = <32>;
status = "okay";
};
&m4_rproc {
memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
<&vdev0vring1>, <&vdev0buffer>;
mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
mbox-names = "vq0", "vq1", "shutdown";
interrupt-parent = <&exti>;
interrupts = <68 1>;
status = "okay";
};
&pwr_regulators {
vdd-supply = <&vdd>;
vdd_3v3_usbfs-supply = <&vdd_usb>;
};
&qspi {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
flash0: mx66l51235l@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-rx-bus-width = <4>;
spi-max-frequency = <108000000>;
#address-cells = <1>;
#size-cells = <1>;
};
};
&rng1 {
status = "okay";
};
&rtc {
status = "okay";
};
&sdmmc1 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
broken-cd;
st,sig-dir;
st,neg-edge;
st,use-ckin;
bus-width = <4>;
vmmc-supply = <&vdd_sd>;
status = "okay";
};
&sdmmc2 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
non-removable;
no-sd;
no-sdio;
st,neg-edge;
bus-width = <8>;
vmmc-supply = <&v3v3>;
vqmmc-supply = <&v3v3>;
mmc-ddr-3_3v;
status = "okay";
};
&sdmmc3 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc3_b4_pins_a>;
pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
broken-cd;
st,neg-edge;
bus-width = <4>;
vmmc-supply = <&v3v3>;
vqmmc-supply = <&v3v3>;
mmc-ddr-3_3v;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
status = "okay";
};

16
arch/arm/boot/dts/stm32mp157c-ed1.dts
View File

@ -130,10 +130,12 @@ &gpu {
};
&i2c4 {
pinctrl-names = "default";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c4_pins_a>;
pinctrl-1 = <&i2c4_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
clock-frequency = <400000>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
@ -218,8 +220,6 @@ vtt_ddr: ldo3 {
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
};
@ -241,7 +241,6 @@ v1v8: ldo6 {
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
regulator-over-current-protection;
};
bst_out: boost {
@ -313,7 +312,8 @@ &sdmmc1 {
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
broken-cd;
cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
disable-wp;
st,sig-dir;
st,neg-edge;
st,use-ckin;
@ -334,7 +334,7 @@ &sdmmc2 {
st,neg-edge;
bus-width = <8>;
vmmc-supply = <&v3v3>;
vqmmc-supply = <&v3v3>;
vqmmc-supply = <&vdd>;
mmc-ddr-3_3v;
status = "okay";
};
@ -355,6 +355,10 @@ &uart4 {
status = "okay";
};
&usbotg_hs {
vbus-supply = <&vbus_otg>;
};
&usbphyc_port0 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;

13
arch/arm/boot/dts/stm32mp157c-ev1.dts
View File

@ -174,8 +174,9 @@ nand@0 {
};
&i2c2 {
pinctrl-names = "default";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c2_pins_a>;
pinctrl-1 = <&i2c2_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
@ -210,7 +211,7 @@ stmfx: stmfx@42 {
interrupt-parent = <&gpioi>;
vdd-supply = <&v3v3>;
stmfx_pinctrl: stmfx-pin-controller {
stmfx_pinctrl: pinctrl {
compatible = "st,stmfx-0300-pinctrl";
gpio-controller;
#gpio-cells = <2>;
@ -218,7 +219,7 @@ stmfx_pinctrl: stmfx-pin-controller {
#interrupt-cells = <2>;
gpio-ranges = <&stmfx_pinctrl 0 0 24>;
joystick_pins: joystick {
joystick_pins: joystick-pins {
pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
bias-pull-down;
};
@ -227,8 +228,9 @@ joystick_pins: joystick {
};
&i2c5 {
pinctrl-names = "default";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c5_pins_a>;
pinctrl-1 = <&i2c5_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
@ -353,7 +355,8 @@ &usbh_ehci {
};
&usbotg_hs {
dr_mode = "peripheral";
pinctrl-0 = <&usbotg_hs_pins_a>;
pinctrl-names = "default";
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";

10
arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
View File

@ -216,10 +216,12 @@ cs42l51_rx_endpoint: endpoint@1 {
};
&i2c4 {
pinctrl-names = "default";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c4_pins_a>;
pinctrl-1 = <&i2c4_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
clock-frequency = <400000>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
@ -304,8 +306,6 @@ vtt_ddr: ldo3 {
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
};
@ -328,7 +328,6 @@ v1v2_hdmi: ldo6 {
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
regulator-over-current-protection;
};
bst_out: boost {
@ -479,7 +478,8 @@ &sdmmc1 {
pinctrl-0 = <&sdmmc1_b4_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
broken-cd;
cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
disable-wp;
st,neg-edge;
bus-width = <4>;
vmmc-supply = <&v3v3>;