Merge 3.16-rc4 into usb-next

We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CREDITS

@@ -9,6 +9,10 @@
 			Linus
 ----------
 
+M: Matt Mackal
+E: mpm@selenic.com
+D: SLOB slab allocator
+
 N: Matti Aarnio
 E: mea@nic.funet.fi
 D: Alpha systems hacking, IPv6 and other network related stuff

Documentation/accounting/getdelays.c

@@ -314,6 +314,7 @@ int main(int argc, char *argv[])
 			break;
 		case 'm':
 			strncpy(cpumask, optarg, sizeof(cpumask));
+			cpumask[sizeof(cpumask) - 1] = '\0';
 			maskset = 1;
 			printf("cpumask %s maskset %d\n", cpumask, maskset);
 			break;

Documentation/devicetree/bindings/arm/armada-38x.txt

@@ -6,5 +6,15 @@ following property:
 
 Required root node property:
 
- - compatible: must contain either "marvell,armada380" or
+ - compatible: must contain "marvell,armada380"
-   "marvell,armada385" depending on the variant of the SoC being used.
+
+In addition, boards using the Marvell Armada 385 SoC shall have the
+following property before the previous one:
+
+Required root node property:
+
+compatible: must contain "marvell,armada385"
+
+Example:
+
+compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada380";

Documentation/devicetree/bindings/arm/l2cc.txt

@@ -40,6 +40,9 @@ Optional properties:
 - arm,filter-ranges : <start length> Starting address and length of window to
   filter. Addresses in the filter window are directed to the M1 port. Other
   addresses will go to the M0 port.
+- arm,io-coherent : indicates that the system is operating in an hardware
+  I/O coherent mode. Valid only when the arm,pl310-cache compatible
+  string is used.
 - interrupts : 1 combined interrupt.
 - cache-id-part: cache id part number to be used if it is not present
   on hardware

Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt

@@ -48,7 +48,7 @@ adc@12D10000 {
 
 	/* NTC thermistor is a hwmon device */
 	ncp15wb473@0 {
-		compatible = "ntc,ncp15wb473";
+		compatible = "murata,ncp15wb473";
 		pullup-uv = <1800000>;
 		pullup-ohm = <47000>;
 		pulldown-ohm = <0>;

Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt

@@ -3,11 +3,19 @@ NTC Thermistor hwmon sensors
 
 Requires node properties:
 - "compatible" value : one of
-	"ntc,ncp15wb473"
+	"murata,ncp15wb473"
-	"ntc,ncp18wb473"
+	"murata,ncp18wb473"
-	"ntc,ncp21wb473"
+	"murata,ncp21wb473"
-	"ntc,ncp03wb473"
+	"murata,ncp03wb473"
-	"ntc,ncp15wl333"
+	"murata,ncp15wl333"
+
+/* Usage of vendor name "ntc" is deprecated */
+<DEPRECATED>	"ntc,ncp15wb473"
+<DEPRECATED>	"ntc,ncp18wb473"
+<DEPRECATED>	"ntc,ncp21wb473"
+<DEPRECATED>	"ntc,ncp03wb473"
+<DEPRECATED>	"ntc,ncp15wl333"
+
 - "pullup-uv"	Pull up voltage in micro volts
 - "pullup-ohm"	Pull up resistor value in ohms
 - "pulldown-ohm" Pull down resistor value in ohms
@@ -21,7 +29,7 @@ Read more about iio bindings at
 
 Example:
 	ncp15wb473@0 {
-		compatible = "ntc,ncp15wb473";
+		compatible = "murata,ncp15wb473";
 		pullup-uv = <1800000>;
 		pullup-ohm = <47000>;
 		pulldown-ohm = <0>;

Documentation/devicetree/bindings/spi/qcom,spi-qup.txt

@@ -23,6 +23,12 @@ Optional properties:
 - spi-max-frequency: Specifies maximum SPI clock frequency,
                      Units - Hz. Definition as per
                      Documentation/devicetree/bindings/spi/spi-bus.txt
+- num-cs:	total number of chipselects
+- cs-gpios:	should specify GPIOs used for chipselects.
+		The gpios will be referred to as reg = <index> in the SPI child
+		nodes.  If unspecified, a single SPI device without a chip
+		select can be used.
+
 
 SPI slave nodes must be children of the SPI master node and can contain
 properties described in Documentation/devicetree/bindings/spi/spi-bus.txt

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -83,6 +83,7 @@ mosaixtech	Mosaix Technologies, Inc.
 moxa	Moxa
 mpl	MPL AG
 mundoreader	Mundo Reader S.L.
+murata	Murata Manufacturing Co., Ltd.
 mxicy	Macronix International Co., Ltd.
 national	National Semiconductor
 neonode		Neonode Inc.

Documentation/email-clients.txt

@@ -1,6 +1,17 @@
 Email clients info for Linux
 ======================================================================
 
+Git
+----------------------------------------------------------------------
+These days most developers use `git send-email` instead of regular
+email clients.  The man page for this is quite good.  On the receiving
+end, maintainers use `git am` to apply the patches.
+
+If you are new to git then send your first patch to yourself.  Save it
+as raw text including all the headers.  Run `git am raw_email.txt` and
+then review the changelog with `git log`.  When that works then send
+the patch to the appropriate mailing list(s).
+
 General Preferences
 ----------------------------------------------------------------------
 Patches for the Linux kernel are submitted via email, preferably as

Documentation/hwmon/ntc_thermistor

@@ -1,7 +1,7 @@
 Kernel driver ntc_thermistor
 =================
 
-Supported thermistors:
+Supported thermistors from Murata:
 * Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333
   Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473', 'ncp15wl333'
   Datasheet: Publicly available at Murata
@@ -15,9 +15,9 @@ Authors:
 Description
 -----------
 
-The NTC thermistor is a simple thermistor that requires users to provide the
+The NTC (Negative Temperature Coefficient) thermistor is a simple thermistor
-resistance and lookup the corresponding compensation table to get the
+that requires users to provide the resistance and lookup the corresponding
-temperature input.
+compensation table to get the temperature input.
 
 The NTC driver provides lookup tables with a linear approximation function
 and four circuit models with an option not to use any of the four models.

Documentation/kernel-parameters.txt

@@ -3130,6 +3130,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			[KNL] Should the soft-lockup detector generate panics.
 			Format: <integer>
 
+	softlockup_all_cpu_backtrace=
+			[KNL] Should the soft-lockup detector generate
+			backtraces on all cpus.
+			Format: <integer>
+
 	sonypi.*=	[HW] Sony Programmable I/O Control Device driver
 			See Documentation/laptops/sonypi.txt
 

Documentation/memory-hotplug.txt

@@ -209,15 +209,12 @@ If memory device is found, memory hotplug code will be called.
 
 4.2 Notify memory hot-add event by hand
 ------------
-On powerpc, the firmware does not notify a memory hotplug event to the kernel.
+On some architectures, the firmware may not notify the kernel of a memory
-Therefore, "probe" interface is supported to notify the event to the kernel.
+hotplug event.  Therefore, the memory "probe" interface is supported to
-This interface depends on CONFIG_ARCH_MEMORY_PROBE.
+explicitly notify the kernel.  This interface depends on
-
+CONFIG_ARCH_MEMORY_PROBE and can be configured on powerpc, sh, and x86
-CONFIG_ARCH_MEMORY_PROBE is supported on powerpc only. On x86, this config
+if hotplug is supported, although for x86 this should be handled by ACPI
-option is disabled by default since ACPI notifies a memory hotplug event to
+notification.
-the kernel, which performs its hotplug operation as the result. Please
-enable this option if you need the "probe" interface for testing purposes
-on x86.
 
 Probe interface is located at
 /sys/devices/system/memory/probe

Documentation/ptp/testptp.c

@@ -17,6 +17,7 @@
  *  along with this program; if not, write to the Free Software
  *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
+#define _GNU_SOURCE
 #include <errno.h>
 #include <fcntl.h>
 #include <inttypes.h>
@@ -46,12 +47,14 @@
 #define CLOCK_INVALID -1
 #endif
 
-/* When glibc offers the syscall, this will go away. */
+/* clock_adjtime is not available in GLIBC < 2.14 */
+#if !__GLIBC_PREREQ(2, 14)
 #include <sys/syscall.h>
 static int clock_adjtime(clockid_t id, struct timex *tx)
 {
 	return syscall(__NR_clock_adjtime, id, tx);
 }
+#endif
 
 static clockid_t get_clockid(int fd)
 {

Documentation/sound/alsa/HD-Audio-Models.txt

@@ -286,6 +286,11 @@ STAC92HD83*
   hp-inv-led	HP with broken BIOS for inverted mute LED
   auto		BIOS setup (default)
 
+STAC92HD95
+==========
+  hp-led	LED support for HP laptops
+  hp-bass	Bass HPF setup for HP Spectre 13
+
 STAC9872
 ========
   vaio		VAIO laptop without SPDIF

Documentation/sysctl/kernel.txt

@@ -75,6 +75,7 @@ show up in /proc/sys/kernel:
 - shmall
 - shmmax                      [ sysv ipc ]
 - shmmni
+- softlockup_all_cpu_backtrace
 - stop-a                      [ SPARC only ]
 - sysrq                       ==> Documentation/sysrq.txt
 - sysctl_writes_strict
@@ -783,6 +784,22 @@ via the /proc/sys interface:
 
 ==============================================================
 
+softlockup_all_cpu_backtrace:
+
+This value controls the soft lockup detector thread's behavior
+when a soft lockup condition is detected as to whether or not
+to gather further debug information. If enabled, each cpu will
+be issued an NMI and instructed to capture stack trace.
+
+This feature is only applicable for architectures which support
+NMI.
+
+0: do nothing. This is the default behavior.
+
+1: on detection capture more debug information.
+
+==============================================================
+
 tainted:
 
 Non-zero if the kernel has been tainted.  Numeric values, which

Documentation/sysctl/vm.txt

@@ -702,7 +702,8 @@ The batch value of each per cpu pagelist is also updated as a result.  It is
 set to pcp->high/4.  The upper limit of batch is (PAGE_SHIFT * 8)
 
 The initial value is zero.  Kernel does not use this value at boot time to set
-the high water marks for each per cpu page list.
+the high water marks for each per cpu page list.  If the user writes '0' to this
+sysctl, it will revert to this default behavior.
 
 ==============================================================
 

Documentation/trace/postprocess/trace-vmscan-postprocess.pl

@@ -47,7 +47,6 @@ use constant HIGH_KSWAPD_REWAKEUP		=> 21;
 use constant HIGH_NR_SCANNED			=> 22;
 use constant HIGH_NR_TAKEN			=> 23;
 use constant HIGH_NR_RECLAIMED			=> 24;
-use constant HIGH_NR_CONTIG_DIRTY		=> 25;
 
 my %perprocesspid;
 my %perprocess;
@@ -105,7 +104,7 @@ my $regex_direct_end_default = 'nr_reclaimed=([0-9]*)';
 my $regex_kswapd_wake_default = 'nid=([0-9]*) order=([0-9]*)';
 my $regex_kswapd_sleep_default = 'nid=([0-9]*)';
 my $regex_wakeup_kswapd_default = 'nid=([0-9]*) zid=([0-9]*) order=([0-9]*)';
-my $regex_lru_isolate_default = 'isolate_mode=([0-9]*) order=([0-9]*) nr_requested=([0-9]*) nr_scanned=([0-9]*) nr_taken=([0-9]*) contig_taken=([0-9]*) contig_dirty=([0-9]*) contig_failed=([0-9]*)';
+my $regex_lru_isolate_default = 'isolate_mode=([0-9]*) order=([0-9]*) nr_requested=([0-9]*) nr_scanned=([0-9]*) nr_taken=([0-9]*) file=([0-9]*)';
 my $regex_lru_shrink_inactive_default = 'nid=([0-9]*) zid=([0-9]*) nr_scanned=([0-9]*) nr_reclaimed=([0-9]*) priority=([0-9]*) flags=([A-Z_|]*)';
 my $regex_lru_shrink_active_default = 'lru=([A-Z_]*) nr_scanned=([0-9]*) nr_rotated=([0-9]*) priority=([0-9]*)';
 my $regex_writepage_default = 'page=([0-9a-f]*) pfn=([0-9]*) flags=([A-Z_|]*)';
@@ -200,7 +199,7 @@ $regex_lru_isolate = generate_traceevent_regex(
 			$regex_lru_isolate_default,
 			"isolate_mode", "order",
 			"nr_requested", "nr_scanned", "nr_taken",
-			"contig_taken", "contig_dirty", "contig_failed");
+			"file");
 $regex_lru_shrink_inactive = generate_traceevent_regex(
 			"vmscan/mm_vmscan_lru_shrink_inactive",
 			$regex_lru_shrink_inactive_default,
@@ -375,7 +374,6 @@ EVENT_PROCESS:
 			}
 			my $isolate_mode = $1;
 			my $nr_scanned = $4;
-			my $nr_contig_dirty = $7;
 
 			# To closer match vmstat scanning statistics, only count isolate_both
 			# and isolate_inactive as scanning. isolate_active is rotation
@@ -385,7 +383,6 @@ EVENT_PROCESS:
 			if ($isolate_mode != 2) {
 				$perprocesspid{$process_pid}->{HIGH_NR_SCANNED} += $nr_scanned;
 			}
-			$perprocesspid{$process_pid}->{HIGH_NR_CONTIG_DIRTY} += $nr_contig_dirty;
 		} elsif ($tracepoint eq "mm_vmscan_lru_shrink_inactive") {
 			$details = $6;
 			if ($details !~ /$regex_lru_shrink_inactive/o) {
@@ -539,13 +536,6 @@ sub dump_stats {
 				}
 			}
 		}
-		if ($stats{$process_pid}->{HIGH_NR_CONTIG_DIRTY}) {
-			print "      ";
-			my $count = $stats{$process_pid}->{HIGH_NR_CONTIG_DIRTY};
-			if ($count != 0) {
-				print "contig-dirty=$count ";
-			}
-		}
 
 		print "\n";
 	}

MAINTAINERS

@@ -943,16 +943,10 @@ L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
 F:	arch/arm/mach-imx/
+F:	arch/arm/mach-mxs/
 F:	arch/arm/boot/dts/imx*
 F:	arch/arm/configs/imx*_defconfig
 
-ARM/FREESCALE MXS ARM ARCHITECTURE
-M:	Shawn Guo <shawn.guo@linaro.org>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-T:	git git://git.linaro.org/people/shawnguo/linux-2.6.git
-F:	arch/arm/mach-mxs/
-
 ARM/GLOMATION GESBC9312SX MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -1052,9 +1046,33 @@ M:	Santosh Shilimkar <santosh.shilimkar@ti.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-keystone/
-F:	drivers/clk/keystone/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone.git
 
+ARM/TEXAS INSTRUMENT KEYSTONE CLOCK FRAMEWORK
+M:	Santosh Shilimkar <santosh.shilimkar@ti.com>
+L:	linux-kernel@vger.kernel.org
+S:	Maintained
+F:	drivers/clk/keystone/
+
+ARM/TEXAS INSTRUMENT KEYSTONE ClOCKSOURCE
+M:	Santosh Shilimkar <santosh.shilimkar@ti.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-kernel@vger.kernel.org
+S:	Maintained
+F:	drivers/clocksource/timer-keystone.c
+
+ARM/TEXAS INSTRUMENT KEYSTONE RESET DRIVER
+M:	Santosh Shilimkar <santosh.shilimkar@ti.com>
+L:	linux-kernel@vger.kernel.org
+S:	Maintained
+F:	drivers/power/reset/keystone-reset.c
+
+ARM/TEXAS INSTRUMENT AEMIF/EMIF DRIVERS
+M:	Santosh Shilimkar <santosh.shilimkar@ti.com>
+L:	linux-kernel@vger.kernel.org
+S:	Maintained
+F:	drivers/memory/*emif*
+
 ARM/LOGICPD PXA270 MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -2917,6 +2935,9 @@ L:	linux-doc@vger.kernel.org
 T:	quilt http://www.infradead.org/~rdunlap/Doc/patches/
 S:	Maintained
 F:	Documentation/
+X:	Documentation/ABI/
+X:	Documentation/devicetree/
+X:	Documentation/[a-z][a-z]_[A-Z][A-Z]/
 
 DOUBLETALK DRIVER
 M:	"James R. Van Zandt" <jrv@vanzandt.mv.com>
@@ -3189,14 +3210,6 @@ L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/eata_pio.*
 
-EBTABLES
-L:	netfilter-devel@vger.kernel.org
-W:	http://ebtables.sourceforge.net/
-S:	Orphan
-F:	include/linux/netfilter_bridge/ebt_*.h
-F:	include/uapi/linux/netfilter_bridge/ebt_*.h
-F:	net/bridge/netfilter/ebt*.c
-
 EC100 MEDIA DRIVER
 M:	Antti Palosaari <crope@iki.fi>
 L:	linux-media@vger.kernel.org
@@ -5517,10 +5530,11 @@ S:	Maintained
 F:	arch/arm/mach-lpc32xx/
 
 LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
-M:	Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
+M:	Nagalakshmi Nandigama <nagalakshmi.nandigama@avagotech.com>
-M:	Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
+M:	Praveen Krishnamoorthy <praveen.krishnamoorthy@avagotech.com>
-M:	support@lsi.com
+M:	Sreekanth Reddy <sreekanth.reddy@avagotech.com>
-L:	DL-MPTFusionLinux@lsi.com
+M:	Abhijit Mahajan <abhijit.mahajan@avagotech.com>
+L:	MPT-FusionLinux.pdl@avagotech.com
 L:	linux-scsi@vger.kernel.org
 W:	http://www.lsilogic.com/support
 S:	Supported
@@ -6105,12 +6119,11 @@ F:	Documentation/networking/s2io.txt
 F:	Documentation/networking/vxge.txt
 F:	drivers/net/ethernet/neterion/
 
-NETFILTER/IPTABLES
+NETFILTER ({IP,IP6,ARP,EB,NF}TABLES)
 M:	Pablo Neira Ayuso <pablo@netfilter.org>
 M:	Patrick McHardy <kaber@trash.net>
 M:	Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
 L:	netfilter-devel@vger.kernel.org
-L:	netfilter@vger.kernel.org
 L:	coreteam@netfilter.org
 W:	http://www.netfilter.org/
 W:	http://www.iptables.org/
@@ -8196,13 +8209,15 @@ S:	Maintained
 F:	drivers/usb/misc/sisusbvga/
 
 SLAB ALLOCATOR
-M:	Christoph Lameter <cl@linux-foundation.org>
+M:	Christoph Lameter <cl@linux.com>
 M:	Pekka Enberg <penberg@kernel.org>
-M:	Matt Mackall <mpm@selenic.com>
+M:	David Rientjes <rientjes@google.com>
+M:	Joonsoo Kim <iamjoonsoo.kim@lge.com>
+M:	Andrew Morton <akpm@linux-foundation.org>
 L:	linux-mm@kvack.org
 S:	Maintained
 F:	include/linux/sl?b*.h
-F:	mm/sl?b.c
+F:	mm/sl?b*
 
 SLEEPABLE READ-COPY UPDATE (SRCU)
 M:	Lai Jiangshan <laijs@cn.fujitsu.com>
@@ -9410,12 +9425,6 @@ S:	Maintained
 F:	drivers/usb/host/isp116x*
 F:	include/linux/usb/isp116x.h
 
-USB KAWASAKI LSI DRIVER
-M:	Oliver Neukum <oliver@neukum.org>
-L:	linux-usb@vger.kernel.org
-S:	Maintained
-F:	drivers/usb/serial/kl5kusb105.*
-
 USB MASS STORAGE DRIVER
 M:	Matthew Dharm <mdharm-usb@one-eyed-alien.net>
 L:	linux-usb@vger.kernel.org
@@ -9443,12 +9452,6 @@ S:	Maintained
 F:	Documentation/usb/ohci.txt
 F:	drivers/usb/host/ohci*
 
-USB OPTION-CARD DRIVER
-M:	Matthias Urlichs <smurf@smurf.noris.de>
-L:	linux-usb@vger.kernel.org
-S:	Maintained
-F:	drivers/usb/serial/option.c
-
 USB PEGASUS DRIVER
 M:	Petko Manolov <petkan@nucleusys.com>
 L:	linux-usb@vger.kernel.org
@@ -9481,7 +9484,7 @@ S:	Maintained
 F:	drivers/net/usb/rtl8150.c
 
 USB SERIAL SUBSYSTEM
-M:	Johan Hovold <jhovold@gmail.com>
+M:	Johan Hovold <johan@kernel.org>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	Documentation/usb/usb-serial.txt

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 16
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc4
 NAME = Shuffling Zombie Juror
 
 # *DOCUMENTATION*
@@ -126,7 +126,10 @@ PHONY += $(MAKECMDGOALS) sub-make
 $(filter-out _all sub-make $(CURDIR)/Makefile, $(MAKECMDGOALS)) _all: sub-make
 	@:
 
+# Fake the "Entering directory" message once, so that IDEs/editors are
+# able to understand relative filenames.
 sub-make: FORCE
+	@echo "make[1]: Entering directory \`$(KBUILD_OUTPUT)'"
 	$(if $(KBUILD_VERBOSE:1=),@)$(MAKE) -C $(KBUILD_OUTPUT) \
 	KBUILD_SRC=$(CURDIR) \
 	KBUILD_EXTMOD="$(KBUILD_EXTMOD)" -f $(CURDIR)/Makefile \

arch/arc/include/asm/cache.h

@@ -60,7 +60,7 @@ extern void read_decode_cache_bcr(void);
 #define ARC_REG_IC_IVIC		0x10
 #define ARC_REG_IC_CTRL		0x11
 #define ARC_REG_IC_IVIL		0x19
-#if defined(CONFIG_ARC_MMU_V3) || defined (CONFIG_ARC_MMU_V4)
+#if defined(CONFIG_ARC_MMU_V3)
 #define ARC_REG_IC_PTAG		0x1E
 #endif
 
@@ -74,7 +74,7 @@ extern void read_decode_cache_bcr(void);
 #define ARC_REG_DC_IVDL		0x4A
 #define ARC_REG_DC_FLSH		0x4B
 #define ARC_REG_DC_FLDL		0x4C
-#if defined(CONFIG_ARC_MMU_V3) || defined (CONFIG_ARC_MMU_V4)
+#if defined(CONFIG_ARC_MMU_V3)
 #define ARC_REG_DC_PTAG		0x5C
 #endif
 

arch/arc/include/uapi/asm/ptrace.h

@@ -11,6 +11,7 @@
 #ifndef _UAPI__ASM_ARC_PTRACE_H
 #define _UAPI__ASM_ARC_PTRACE_H
 
+#define PTRACE_GET_THREAD_AREA	25
 
 #ifndef __ASSEMBLY__
 /*

arch/arc/kernel/ctx_sw_asm.S

@@ -10,9 +10,9 @@
  *  -This is the more "natural" hand written assembler
  */
 
+#include <linux/linkage.h>
 #include <asm/entry.h>       /* For the SAVE_* macros */
 #include <asm/asm-offsets.h>
-#include <asm/linkage.h>
 
 #define KSP_WORD_OFF 	((TASK_THREAD + THREAD_KSP) / 4)
 

arch/arc/kernel/devtree.c

@@ -41,7 +41,7 @@ const struct machine_desc * __init setup_machine_fdt(void *dt)
 {
 	const struct machine_desc *mdesc;
 	unsigned long dt_root;
-	void *clk;
+	const void *clk;
 	int len;
 
 	if (!early_init_dt_scan(dt))

arch/arc/kernel/head.S

@@ -77,10 +77,11 @@ stext:
 	; Clear BSS before updating any globals
 	; XXX: use ZOL here
 	mov	r5, __bss_start
-	mov	r6, __bss_stop
+	sub	r6, __bss_stop, r5
+	lsr.f	lp_count, r6, 2
+	lpnz	1f
+	st.ab   0, [r5, 4]
 1:
-	st.ab   0, [r5,4]
-	brlt    r5, r6, 1b
 
 	; Uboot - kernel ABI
 	;    r0 = [0] No uboot interaction, [1] cmdline in r2, [2] DTB in r2

arch/arc/kernel/ptrace.c

@@ -146,6 +146,10 @@ long arch_ptrace(struct task_struct *child, long request,
 	pr_debug("REQ=%ld: ADDR =0x%lx, DATA=0x%lx)\n", request, addr, data);
 
 	switch (request) {
+	case PTRACE_GET_THREAD_AREA:
+		ret = put_user(task_thread_info(child)->thr_ptr,
+			       (unsigned long __user *)data);
+		break;
 	default:
 		ret = ptrace_request(child, request, addr, data);
 		break;

arch/arc/kernel/smp.c

@@ -337,8 +337,19 @@ irqreturn_t do_IPI(int irq, void *dev_id)
  * API called by platform code to hookup arch-common ISR to their IPI IRQ
  */
 static DEFINE_PER_CPU(int, ipi_dev);
+
+static struct irqaction arc_ipi_irq = {
+        .name    = "IPI Interrupt",
+        .flags   = IRQF_PERCPU,
+        .handler = do_IPI,
+};
+
 int smp_ipi_irq_setup(int cpu, int irq)
 {
-	int *dev_id = &per_cpu(ipi_dev, smp_processor_id());
+	if (!cpu)
-	return request_percpu_irq(irq, do_IPI, "IPI Interrupt", dev_id);
+		return setup_irq(irq, &arc_ipi_irq);
+	else
+		arch_unmask_irq(irq);
+
+	return 0;
 }

arch/arc/kernel/vmlinux.lds.S

@@ -116,7 +116,7 @@ SECTIONS
 
 	_edata = .;
 
-	BSS_SECTION(0, 0, 0)
+	BSS_SECTION(4, 4, 4)
 
 #ifdef CONFIG_ARC_DW2_UNWIND
 	. = ALIGN(PAGE_SIZE);

arch/arc/mm/cache_arc700.c

@@ -389,7 +389,7 @@ static inline void __dc_line_op(unsigned long paddr, unsigned long vaddr,
 /***********************************************************
  * Machine specific helper for per line I-Cache invalidate.
  */
-static void __ic_line_inv_vaddr(unsigned long paddr, unsigned long vaddr,
+static void __ic_line_inv_vaddr_local(unsigned long paddr, unsigned long vaddr,
 				unsigned long sz)
 {
 	unsigned long flags;
@@ -405,6 +405,23 @@ static inline void __ic_entire_inv(void)
 	read_aux_reg(ARC_REG_IC_CTRL);	/* blocks */
 }
 
+struct ic_line_inv_vaddr_ipi {
+	unsigned long paddr, vaddr;
+	int sz;
+};
+
+static void __ic_line_inv_vaddr_helper(void *info)
+{
+        struct ic_line_inv_vaddr_ipi *ic_inv = (struct ic_line_inv_vaddr_ipi*) info;
+        __ic_line_inv_vaddr_local(ic_inv->paddr, ic_inv->vaddr, ic_inv->sz);
+}
+
+static void __ic_line_inv_vaddr(unsigned long paddr, unsigned long vaddr,
+				unsigned long sz)
+{
+	struct ic_line_inv_vaddr_ipi ic_inv = { paddr, vaddr , sz};
+	on_each_cpu(__ic_line_inv_vaddr_helper, &ic_inv, 1);
+}
 #else
 
 #define __ic_entire_inv()
@@ -553,12 +570,8 @@ void flush_icache_range(unsigned long kstart, unsigned long kend)
  */
 void __sync_icache_dcache(unsigned long paddr, unsigned long vaddr, int len)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
-	__ic_line_inv_vaddr(paddr, vaddr, len);
 	__dc_line_op(paddr, vaddr, len, OP_FLUSH_N_INV);
-	local_irq_restore(flags);
+	__ic_line_inv_vaddr(paddr, vaddr, len);
 }
 
 /* wrapper to compile time eliminate alignment checks in flush loop */

arch/arm/boot/dts/Makefile

@@ -357,7 +357,7 @@ dtb-$(CONFIG_ARCH_STI)+= stih407-b2120.dtb \
 	stih415-b2020.dtb \
 	stih416-b2000.dtb \
 	stih416-b2020.dtb \
-	stih416-b2020-revE.dtb
+	stih416-b2020e.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
 	sun4i-a10-cubieboard.dtb \

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -319,6 +319,10 @@ &cpsw_emac1 {
 	phy-mode = "rmii";
 };
 
+&phy_sel {
+	rmii-clock-ext;
+};
+
 &i2c0 {
 	status = "okay";
 	pinctrl-names = "default";

arch/arm/boot/dts/armada-380.dtsi

@@ -16,7 +16,7 @@
 
 / {
 	model = "Marvell Armada 380 family SoC";
-	compatible = "marvell,armada380", "marvell,armada38x";
+	compatible = "marvell,armada380";
 
 	cpus {
 		#address-cells = <1>;

arch/arm/boot/dts/armada-385-db.dts

@@ -16,7 +16,7 @@
 
 / {
 	model = "Marvell Armada 385 Development Board";
-	compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada38x";
+	compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada380";
 
 	chosen {
 		bootargs = "console=ttyS0,115200 earlyprintk";

arch/arm/boot/dts/armada-385-rd.dts

@@ -17,7 +17,7 @@
 
 / {
 	model = "Marvell Armada 385 Reference Design";
-	compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada38x";
+	compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada380";
 
 	chosen {
 		bootargs = "console=ttyS0,115200 earlyprintk";

arch/arm/boot/dts/armada-385.dtsi

@@ -16,7 +16,7 @@
 
 / {
 	model = "Marvell Armada 385 family SoC";
-	compatible = "marvell,armada385", "marvell,armada38x";
+	compatible = "marvell,armada385", "marvell,armada380";
 
 	cpus {
 		#address-cells = <1>;

arch/arm/boot/dts/armada-38x.dtsi

@@ -20,7 +20,7 @@
 
 / {
 	model = "Marvell Armada 38x family SoC";
-	compatible = "marvell,armada38x";
+	compatible = "marvell,armada380";
 
 	aliases {
 		gpio0 = &gpio0;

arch/arm/boot/dts/at91sam9261.dtsi

@@ -568,24 +568,17 @@ pmc: pmc@fffffc00 {
 				#size-cells = <0>;
 				#interrupt-cells = <1>;
 
-				slow_rc_osc: slow_rc_osc {
+				main_osc: main_osc {
-					compatible = "fixed-clock";
+					compatible = "atmel,at91rm9200-clk-main-osc";
 					#clock-cells = <0>;
-					clock-frequency = <32768>;
+					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
-					clock-accuracy = <50000000>;
+					clocks = <&main_xtal>;
-				};
-
-				clk32k: slck {
-					compatible = "atmel,at91sam9260-clk-slow";
-					#clock-cells = <0>;
-					clocks = <&slow_rc_osc &slow_xtal>;
 				};
 
 				main: mainck {
 					compatible = "atmel,at91rm9200-clk-main";
 					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
+					clocks = <&main_osc>;
-					clocks = <&main_xtal>;
 				};
 
 				plla: pllack {
@@ -615,7 +608,7 @@ mck: masterck {
 					compatible = "atmel,at91rm9200-clk-master";
 					#clock-cells = <0>;
 					interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
-					clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
+					clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
 					atmel,clk-output-range = <0 94000000>;
 					atmel,clk-divisors = <1 2 4 0>;
 				};
@@ -632,7 +625,7 @@ prog: progck {
 					#address-cells = <1>;
 					#size-cells = <0>;
 					interrupt-parent = <&pmc>;
-					clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
+					clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
 
 					prog0: prog0 {
 						#clock-cells = <0>;

arch/arm/boot/dts/at91sam9261ek.dts

@@ -20,6 +20,10 @@ memory {
 		reg = <0x20000000 0x4000000>;
 	};
 
+	slow_xtal {
+		clock-frequency = <32768>;
+	};
+
 	main_xtal {
 		clock-frequency = <18432000>;
 	};

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -132,8 +132,8 @@ plla: pllack {
 								      <595000000 650000000 3 0>,
 								      <545000000 600000000 0 1>,
 								      <495000000 555000000 1 1>,
-								      <445000000 500000000 1 2>,
+								      <445000000 500000000 2 1>,
-								      <400000000 450000000 1 3>;
+								      <400000000 450000000 3 1>;
 				};
 
 				plladiv: plladivck {

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -140,8 +140,8 @@ plla: pllack {
 								       595000000 650000000 3 0
 								       545000000 600000000 0 1
 								       495000000 555000000 1 1
-								       445000000 500000000 1 2
+								       445000000 500000000 2 1
-								       400000000 450000000 1 3>;
+								       400000000 450000000 3 1>;
 				};
 
 				plladiv: plladivck {

arch/arm/boot/dts/dra7.dtsi

@@ -773,7 +773,6 @@ qspi: qspi@4b300000 {
 			clocks = <&qspi_gfclk_div>;
 			clock-names = "fck";
 			num-cs = <4>;
-			interrupts = <0 343 0x4>;
 			status = "disabled";
 		};
 
@@ -984,6 +983,17 @@ gpmc: gpmc@50000000 {
 			#size-cells = <1>;
 			status = "disabled";
 		};
+
+		atl: atl@4843c000 {
+			compatible = "ti,dra7-atl";
+			reg = <0x4843c000 0x3ff>;
+			ti,hwmods = "atl";
+			ti,provided-clocks = <&atl_clkin0_ck>, <&atl_clkin1_ck>,
+					     <&atl_clkin2_ck>, <&atl_clkin3_ck>;
+			clocks = <&atl_gfclk_mux>;
+			clock-names = "fck";
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/dra7xx-clocks.dtsi

@@ -10,26 +10,26 @@
 &cm_core_aon_clocks {
 	atl_clkin0_ck: atl_clkin0_ck {
 		#clock-cells = <0>;
-		compatible = "fixed-clock";
+		compatible = "ti,dra7-atl-clock";
-		clock-frequency = <0>;
+		clocks = <&atl_gfclk_mux>;
 	};
 
 	atl_clkin1_ck: atl_clkin1_ck {
 		#clock-cells = <0>;
-		compatible = "fixed-clock";
+		compatible = "ti,dra7-atl-clock";
-		clock-frequency = <0>;
+		clocks = <&atl_gfclk_mux>;
 	};
 
 	atl_clkin2_ck: atl_clkin2_ck {
 		#clock-cells = <0>;
-		compatible = "fixed-clock";
+		compatible = "ti,dra7-atl-clock";
-		clock-frequency = <0>;
+		clocks = <&atl_gfclk_mux>;
 	};
 
 	atl_clkin3_ck: atl_clkin3_ck {
 		#clock-cells = <0>;
-		compatible = "fixed-clock";
+		compatible = "ti,dra7-atl-clock";
-		clock-frequency = <0>;
+		clocks = <&atl_gfclk_mux>;
 	};
 
 	hdmi_clkin_ck: hdmi_clkin_ck {

arch/arm/boot/dts/exynos4.dtsi

@@ -113,7 +113,7 @@ gic: interrupt-controller@10490000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
-		reg = <0x10490000 0x1000>, <0x10480000 0x100>;
+		reg = <0x10490000 0x10000>, <0x10480000 0x10000>;
 	};
 
 	combiner: interrupt-controller@10440000 {

arch/arm/boot/dts/imx51-babbage.dts

@@ -315,15 +315,15 @@ partition@40000 {
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	fsl,cd-controller;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
-	fsl,wp-controller;
+	wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &esdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc2>;
-	cd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
@@ -468,8 +468,8 @@ MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
 				MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
 				MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
 				MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
-				MX51_PAD_GPIO1_0__SD1_CD		0x20d5
+				MX51_PAD_GPIO1_0__GPIO1_0		0x100
-				MX51_PAD_GPIO1_1__SD1_WP		0x20d5
+				MX51_PAD_GPIO1_1__GPIO1_1		0x100
 			>;
 		};
 

arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts

@@ -107,7 +107,7 @@ &audmux {
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1 &pinctrl_esdhc1_cd>;
-	fsl,cd-controller;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -206,7 +206,7 @@ MX51_PAD_DI1_D1_CS__GPIO3_4 0x1f5
 
 		pinctrl_esdhc1_cd: esdhc1_cd {
 			fsl,pins = <
-				MX51_PAD_GPIO1_0__SD1_CD 0x20d5
+				MX51_PAD_GPIO1_0__GPIO1_0 0xd5
 			>;
 		};
 

arch/arm/boot/dts/imx53-m53evk.dts

@@ -21,27 +21,25 @@ memory {
 		      <0xb0000000 0x20000000>;
 	};
 
-	soc {
+	display1: display@di1 {
-		display1: display@di1 {
+		compatible = "fsl,imx-parallel-display";
-			compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
-			interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
-			pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp1>;
-			pinctrl-0 = <&pinctrl_ipu_disp1>;
 
-			display-timings {
+		display-timings {
-				800x480p60 {
+			800x480p60 {
-					native-mode;
+				native-mode;
-					clock-frequency = <31500000>;
+				clock-frequency = <31500000>;
-					hactive = <800>;
+				hactive = <800>;
-					vactive = <480>;
+				vactive = <480>;
-					hfront-porch = <40>;
+				hfront-porch = <40>;
-					hback-porch = <88>;
+				hback-porch = <88>;
-					hsync-len = <128>;
+				hsync-len = <128>;
-					vback-porch = <33>;
+				vback-porch = <33>;
-					vfront-porch = <9>;
+				vfront-porch = <9>;
-					vsync-len = <3>;
+				vsync-len = <3>;
-					vsync-active = <1>;
+				vsync-active = <1>;
-				};
 			};
 		};
 

arch/arm/boot/dts/imx6dl-hummingboard.dts

@@ -143,6 +143,14 @@ pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
 		};
 
+		pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id {
+			/*
+			 * Similar to pinctrl_usbotg_2, but we want it
+			 * pulled down for a fixed host connection.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+
 		pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
 			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
 		};
@@ -178,6 +186,8 @@ &usbh1 {
 };
 
 &usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6q-gw51xx.dts

@@ -11,7 +11,7 @@
 
 /dts-v1/;
 #include "imx6q.dtsi"
-#include "imx6qdl-gw54xx.dtsi"
+#include "imx6qdl-gw51xx.dtsi"
 
 / {
 	model = "Gateworks Ventana i.MX6 Quad GW51XX";

arch/arm/boot/dts/imx6qdl-cubox-i.dtsi

@@ -12,6 +12,19 @@ ir_recv: ir-receiver {
 		pinctrl-0 = <&pinctrl_cubox_i_ir>;
 	};
 
+	pwmleds {
+		compatible = "pwm-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
+
+		front {
+			active-low;
+			label = "imx6:red:front";
+			max-brightness = <248>;
+			pwms = <&pwm1 0 50000>;
+		};
+	};
+
 	regulators {
 		compatible = "simple-bus";
 
@@ -109,6 +122,10 @@ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000
 			>;
 		};
 
+		pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led {
+			fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
+		};
+
 		pinctrl_cubox_i_spdif: cubox-i-spdif {
 			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
 		};
@@ -117,6 +134,14 @@ pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
 		};
 
+		pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+			/*
+			 * The Cubox-i pulls this low, but as it's pointless
+			 * leaving it as a pull-up, even if it is just 10uA.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+
 		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
 			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>;
 		};
@@ -153,6 +178,8 @@ &usbh1 {
 };
 
 &usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw51xx.dtsi

@@ -161,7 +161,7 @@ &i2c2 {
 	status = "okay";
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -220,7 +220,7 @@ pciswitch: pex8609@3f {
 	};
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {
@@ -288,7 +288,7 @@ accelerometer: fxos8700@1e {
 	codec: sgtl5000@0a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
-		clocks = <&clks 169>;
+		clocks = <&clks 201>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};

arch/arm/boot/dts/imx6qdl-gw53xx.dtsi

@@ -234,7 +234,7 @@ pciswitch: pex8606@3f {
 	};
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {

arch/arm/boot/dts/imx6qdl-microsom.dtsi

@@ -10,14 +10,6 @@ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
 				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
 			>;
 		};
-
-		pinctrl_microsom_usbotg: microsom-usbotg {
-			/*
-			 * Similar to pinctrl_usbotg_2, but we want it
-			 * pulled down for a fixed host connection.
-			 */
-			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
-		};
 	};
 };
 
@@ -26,8 +18,3 @@ &uart1 {
 	pinctrl-0 = <&pinctrl_microsom_uart1>;
 	status = "okay";
 };
-
-&usbotg {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_microsom_usbotg>;
-};

arch/arm/boot/dts/imx6sl.dtsi

@@ -686,7 +686,7 @@ fec: ethernet@02188000 {
 				compatible = "fsl,imx6sl-fec", "fsl,imx25-fec";
 				reg = <0x02188000 0x4000>;
 				interrupts = <0 114 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks IMX6SL_CLK_ENET_REF>,
+				clocks = <&clks IMX6SL_CLK_ENET>,
 					 <&clks IMX6SL_CLK_ENET_REF>;
 				clock-names = "ipg", "ahb";
 				status = "disabled";

arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts

@@ -105,7 +105,6 @@ ethphy0: ethernet-phy@0 {
 		compatible = "ethernet-phy-id0141.0cb0",
 		             "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
-		phy-connection-type = "rgmii-id";
 	};
 
 	ethphy1: ethernet-phy@1 {
@@ -113,7 +112,6 @@ ethphy1: ethernet-phy@1 {
 		compatible = "ethernet-phy-id0141.0cb0",
 		             "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
-		phy-connection-type = "rgmii-id";
 	};
 };
 
@@ -121,6 +119,7 @@ &eth0 {
 	status = "okay";
 	ethernet0-port@0 {
 		phy-handle = <&ethphy0>;
+		phy-connection-type = "rgmii-id";
 	};
 };
 
@@ -128,5 +127,6 @@ &eth1 {
 	status = "okay";
 	ethernet1-port@0 {
 		phy-handle = <&ethphy1>;
+		phy-connection-type = "rgmii-id";
 	};
 };

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -251,6 +251,11 @@ twl_audio: audio {
 			codec {
 			};
 		};
+
+		twl_power: power {
+			compatible = "ti,twl4030-power-beagleboard-xm", "ti,twl4030-power-idle-osc-off";
+			ti,use_poweroff;
+		};
 	};
 };
 
@@ -301,6 +306,7 @@ &usb_otg_hs {
 };
 
 &uart3 {
+	interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
 };

arch/arm/boot/dts/omap3-evm-common.dtsi

@@ -50,6 +50,13 @@ &backlight0 {
 	gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;
 };
 
+&twl {
+	twl_power: power {
+		compatible = "ti,twl4030-power-omap3-evm", "ti,twl4030-power-idle";
+		ti,use_poweroff;
+	};
+};
+
 &i2c2 {
 	clock-frequency = <400000>;
 };

arch/arm/boot/dts/omap3-n900.dts

@@ -351,6 +351,11 @@ twl_audio: audio {
 		compatible = "ti,twl4030-audio";
 		ti,enable-vibra = <1>;
 	};
+
+	twl_power: power {
+		compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
+		ti,use_poweroff;
+	};
 };
 
 &twl_keypad {

arch/arm/boot/dts/omap5.dtsi

@@ -45,7 +45,6 @@ cpu0: cpu@0 {
 
 			operating-points = <
 				/* kHz    uV */
-				500000  880000
 				1000000 1060000
 				1500000 1250000
 			>;

arch/arm/boot/dts/stih415.dtsi

@@ -169,8 +169,8 @@ ethernet0: dwmac@fe810000 {
 
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii0>;
-			clock-names	= "stmmaceth";
+			clock-names	= "stmmaceth", "sti-ethclk";
-			clocks		= <&clk_s_a1_ls CLK_GMAC0_PHY>;
+			clocks		= <&clk_s_a1_ls CLK_ICN_IF_2>, <&clk_s_a1_ls CLK_GMAC0_PHY>;
 		};
 
 		ethernet1: dwmac@fef08000 {
@@ -192,8 +192,8 @@ ethernet1: dwmac@fef08000 {
 			reset-names		= "stmmaceth";
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii1>;
-			clock-names	= "stmmaceth";
+			clock-names	= "stmmaceth", "sti-ethclk";
-			clocks		= <&clk_s_a0_ls CLK_ETH1_PHY>;
+			clocks		= <&clk_s_a0_ls CLK_ICN_REG>, <&clk_s_a0_ls CLK_ETH1_PHY>;
 		};
 
 		rc: rc@fe518000 {

arch/arm/boot/dts/stih416.dtsi

@@ -175,8 +175,8 @@ ethernet0: dwmac@fe810000 {
 			reset-names		= "stmmaceth";
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii0>;
-			clock-names	= "stmmaceth";
+			clock-names	= "stmmaceth", "sti-ethclk";
-			clocks		= <&clk_s_a1_ls CLK_GMAC0_PHY>;
+			clocks		= <&clk_s_a1_ls CLK_ICN_IF_2>, <&clk_s_a1_ls CLK_GMAC0_PHY>;
 		};
 
 		ethernet1: dwmac@fef08000 {
@@ -197,8 +197,8 @@ ethernet1: dwmac@fef08000 {
 			reset-names	= "stmmaceth";
 			pinctrl-names 	= "default";
 			pinctrl-0	= <&pinctrl_mii1>;
-			clock-names	= "stmmaceth";
+			clock-names	= "stmmaceth", "sti-ethclk";
-			clocks		= <&clk_s_a0_ls CLK_ETH1_PHY>;
+			clocks		= <&clk_s_a0_ls CLK_ICN_REG>, <&clk_s_a0_ls CLK_ETH1_PHY>;
 		};
 
 		rc: rc@fe518000 {

arch/arm/common/scoop.c

@@ -182,7 +182,6 @@ static int scoop_probe(struct platform_device *pdev)
 	struct scoop_config *inf;
 	struct resource *mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	int ret;
-	int temp;
 
 	if (!mem)
 		return -EINVAL;

arch/arm/configs/bcm_defconfig

@@ -94,10 +94,10 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_PWM=y
 # CONFIG_USB_SUPPORT is not set
 CONFIG_MMC=y
-CONFIG_MMC_UNSAFE_RESUME=y
 CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_TEST=y
 CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_BCM_KONA=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y

arch/arm/configs/imx_v6_v7_defconfig

@@ -186,6 +186,7 @@ CONFIG_VIDEO_MX3=y
 CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_CODA=y
 CONFIG_SOC_CAMERA_OV2640=y
+CONFIG_IMX_IPUV3_CORE=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y

arch/arm/configs/multi_v7_defconfig

@@ -223,12 +223,12 @@ CONFIG_POWER_RESET_GPIO=y
 CONFIG_POWER_RESET_SUN6I=y
 CONFIG_SENSORS_LM90=y
 CONFIG_THERMAL=y
-CONFIG_DOVE_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
 CONFIG_WATCHDOG=y
 CONFIG_ORION_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=y
 CONFIG_MFD_AS3722=y
+CONFIG_MFD_BCM590XX=y
 CONFIG_MFD_CROS_EC=y
 CONFIG_MFD_CROS_EC_SPI=y
 CONFIG_MFD_MAX8907=y
@@ -240,6 +240,7 @@ CONFIG_MFD_TPS65910=y
 CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
 CONFIG_REGULATOR_AB8500=y
 CONFIG_REGULATOR_AS3722=y
+CONFIG_REGULATOR_BCM590XX=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_REGULATOR_MAX8907=y
 CONFIG_REGULATOR_PALMAS=y
@@ -353,6 +354,7 @@ CONFIG_MFD_NVEC=y
 CONFIG_KEYBOARD_NVEC=y
 CONFIG_SERIO_NVEC_PS2=y
 CONFIG_NVEC_POWER=y
+CONFIG_QCOM_GSBI=y
 CONFIG_COMMON_CLK_QCOM=y
 CONFIG_MSM_GCC_8660=y
 CONFIG_MSM_MMCC_8960=y

arch/arm/configs/mvebu_v7_defconfig

@@ -14,6 +14,7 @@ CONFIG_MACH_ARMADA_370=y
 CONFIG_MACH_ARMADA_375=y
 CONFIG_MACH_ARMADA_38X=y
 CONFIG_MACH_ARMADA_XP=y
+CONFIG_MACH_DOVE=y
 CONFIG_NEON=y
 # CONFIG_CACHE_L2X0 is not set
 # CONFIG_SWP_EMULATE is not set
@@ -52,6 +53,7 @@ CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_I2C=y
 CONFIG_SPI=y
 CONFIG_SPI_ORION=y

arch/arm/include/asm/mcpm.h

@@ -208,8 +208,6 @@ struct sync_struct {
 	struct mcpm_sync_struct clusters[MAX_NR_CLUSTERS];
 };
 
-extern unsigned long sync_phys;	/* physical address of *mcpm_sync */
-
 void __mcpm_cpu_going_down(unsigned int cpu, unsigned int cluster);
 void __mcpm_cpu_down(unsigned int cpu, unsigned int cluster);
 void __mcpm_outbound_leave_critical(unsigned int cluster, int state);

arch/arm/include/asm/thread_info.h

@@ -114,8 +114,14 @@ static inline struct thread_info *current_thread_info(void)
 	((unsigned long)(task_thread_info(tsk)->cpu_context.pc))
 #define thread_saved_sp(tsk)	\
 	((unsigned long)(task_thread_info(tsk)->cpu_context.sp))
+
+#ifndef CONFIG_THUMB2_KERNEL
 #define thread_saved_fp(tsk)	\
 	((unsigned long)(task_thread_info(tsk)->cpu_context.fp))
+#else
+#define thread_saved_fp(tsk)	\
+	((unsigned long)(task_thread_info(tsk)->cpu_context.r7))
+#endif
 
 extern void crunch_task_disable(struct thread_info *);
 extern void crunch_task_copy(struct thread_info *, void *);

arch/arm/kernel/perf_event_v7.c

@@ -1924,7 +1924,7 @@ static int krait_pmu_get_event_idx(struct pmu_hw_events *cpuc,
 				   struct perf_event *event)
 {
 	int idx;
-	int bit;
+	int bit = -1;
 	unsigned int prefix;
 	unsigned int region;
 	unsigned int code;
@@ -1953,7 +1953,7 @@ static int krait_pmu_get_event_idx(struct pmu_hw_events *cpuc,
 	}
 
 	idx = armv7pmu_get_event_idx(cpuc, event);
-	if (idx < 0 && krait_event)
+	if (idx < 0 && bit >= 0)
 		clear_bit(bit, cpuc->used_mask);
 
 	return idx;

arch/arm/kernel/ptrace.c

@@ -908,7 +908,7 @@ enum ptrace_syscall_dir {
 	PTRACE_SYSCALL_EXIT,
 };
 
-static int tracehook_report_syscall(struct pt_regs *regs,
+static void tracehook_report_syscall(struct pt_regs *regs,
 				    enum ptrace_syscall_dir dir)
 {
 	unsigned long ip;
@@ -926,7 +926,6 @@ static int tracehook_report_syscall(struct pt_regs *regs,
 		current_thread_info()->syscall = -1;
 
 	regs->ARM_ip = ip;
-	return current_thread_info()->syscall;
 }
 
 asmlinkage int syscall_trace_enter(struct pt_regs *regs, int scno)
@@ -938,7 +937,9 @@ asmlinkage int syscall_trace_enter(struct pt_regs *regs, int scno)
 		return -1;
 
 	if (test_thread_flag(TIF_SYSCALL_TRACE))
-		scno = tracehook_report_syscall(regs, PTRACE_SYSCALL_ENTER);
+		tracehook_report_syscall(regs, PTRACE_SYSCALL_ENTER);
+
+	scno = current_thread_info()->syscall;
 
 	if (test_thread_flag(TIF_SYSCALL_TRACEPOINT))
 		trace_sys_enter(regs, scno);

arch/arm/mach-exynos/hotplug.c

@@ -46,13 +46,7 @@ static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
 		if (cpu == 1)
 			exynos_cpu_power_down(cpu);
 
-		/*
+		wfi();
-		 * here's the WFI
-		 */
-		asm(".word	0xe320f003\n"
-		    :
-		    :
-		    : "memory", "cc");
 
 		if (pen_release == cpu_logical_map(cpu)) {
 			/*

arch/arm/mach-exynos/mcpm-exynos.c

@@ -25,7 +25,6 @@
 
 #define EXYNOS5420_CPUS_PER_CLUSTER	4
 #define EXYNOS5420_NR_CLUSTERS		2
-#define MCPM_BOOT_ADDR_OFFSET		0x1c
 
 /*
  * The common v7_exit_coherency_flush API could not be used because of the
@@ -343,11 +342,13 @@ static int __init exynos_mcpm_init(void)
 	pr_info("Exynos MCPM support installed\n");
 
 	/*
-	 * Future entries into the kernel can now go
+	 * U-Boot SPL is hardcoded to jump to the start of ns_sram_base_addr
-	 * through the cluster entry vectors.
+	 * as part of secondary_cpu_start().  Let's redirect it to the
+	 * mcpm_entry_point().
 	 */
-	__raw_writel(virt_to_phys(mcpm_entry_point),
+	__raw_writel(0xe59f0000, ns_sram_base_addr);     /* ldr r0, [pc, #0] */
-			ns_sram_base_addr + MCPM_BOOT_ADDR_OFFSET);
+	__raw_writel(0xe12fff10, ns_sram_base_addr + 4); /* bx  r0 */
+	__raw_writel(virt_to_phys(mcpm_entry_point), ns_sram_base_addr + 8);
 
 	iounmap(ns_sram_base_addr);
 

arch/arm/mach-exynos/pm.c

@@ -300,7 +300,7 @@ static int exynos_pm_suspend(void)
 	tmp = (S5P_USE_STANDBY_WFI0 | S5P_USE_STANDBY_WFE0);
 	__raw_writel(tmp, S5P_CENTRAL_SEQ_OPTION);
 
-	if (!soc_is_exynos5250())
+	if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
 		exynos_cpu_save_register();
 
 	return 0;
@@ -334,7 +334,7 @@ static void exynos_pm_resume(void)
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	if (!soc_is_exynos5250())
+	if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
 		exynos_cpu_restore_register();
 
 	/* For release retention */
@@ -353,7 +353,7 @@ static void exynos_pm_resume(void)
 
 	s3c_pm_do_restore_core(exynos_core_save, ARRAY_SIZE(exynos_core_save));
 
-	if (!soc_is_exynos5250())
+	if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
 		scu_enable(S5P_VA_SCU);
 
 early_wakeup:
@@ -440,15 +440,18 @@ static int exynos_cpu_pm_notifier(struct notifier_block *self,
 	case CPU_PM_ENTER:
 		if (cpu == 0) {
 			exynos_pm_central_suspend();
-			exynos_cpu_save_register();
+			if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
+				exynos_cpu_save_register();
 		}
 		break;
 
 	case CPU_PM_EXIT:
 		if (cpu == 0) {
-			if (!soc_is_exynos5250())
+			if (read_cpuid_part_number() ==
+					ARM_CPU_PART_CORTEX_A9) {
 				scu_enable(S5P_VA_SCU);
-			exynos_cpu_restore_register();
+				exynos_cpu_restore_register();
+			}
 			exynos_pm_central_resume();
 		}
 		break;

arch/arm/mach-imx/Kconfig

@@ -734,9 +734,9 @@ config SOC_IMX6
 	select HAVE_IMX_MMDC
 	select HAVE_IMX_SRC
 	select MFD_SYSCON
-	select PL310_ERRATA_588369 if CACHE_PL310
+	select PL310_ERRATA_588369 if CACHE_L2X0
-	select PL310_ERRATA_727915 if CACHE_PL310
+	select PL310_ERRATA_727915 if CACHE_L2X0
-	select PL310_ERRATA_769419 if CACHE_PL310
+	select PL310_ERRATA_769419 if CACHE_L2X0
 
 config SOC_IMX6Q
 	bool "i.MX6 Quad/DualLite support"
@@ -771,9 +771,9 @@ config SOC_VF610
 	select ARM_GIC
 	select PINCTRL_VF610
 	select VF_PIT_TIMER
-	select PL310_ERRATA_588369 if CACHE_PL310
+	select PL310_ERRATA_588369 if CACHE_L2X0
-	select PL310_ERRATA_727915 if CACHE_PL310
+	select PL310_ERRATA_727915 if CACHE_L2X0
-	select PL310_ERRATA_769419 if CACHE_PL310
+	select PL310_ERRATA_769419 if CACHE_L2X0
 
 	help
 	  This enable support for Freescale Vybrid VF610 processor.

arch/arm/mach-imx/clk-imx6sl.c

@@ -312,6 +312,7 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
 	clks[IMX6SL_CLK_ECSPI2]       = imx_clk_gate2("ecspi2",       "ecspi_root",        base + 0x6c, 2);
 	clks[IMX6SL_CLK_ECSPI3]       = imx_clk_gate2("ecspi3",       "ecspi_root",        base + 0x6c, 4);
 	clks[IMX6SL_CLK_ECSPI4]       = imx_clk_gate2("ecspi4",       "ecspi_root",        base + 0x6c, 6);
+	clks[IMX6SL_CLK_ENET]         = imx_clk_gate2("enet",         "ipg",               base + 0x6c, 10);
 	clks[IMX6SL_CLK_EPIT1]        = imx_clk_gate2("epit1",        "perclk",            base + 0x6c, 12);
 	clks[IMX6SL_CLK_EPIT2]        = imx_clk_gate2("epit2",        "perclk",            base + 0x6c, 14);
 	clks[IMX6SL_CLK_EXTERN_AUDIO] = imx_clk_gate2("extern_audio", "extern_audio_podf", base + 0x6c, 16);

arch/arm/mach-integrator/integrator_ap.c

@@ -480,25 +480,18 @@ static const struct of_device_id ebi_match[] = {
 static void __init ap_init_of(void)
 {
 	unsigned long sc_dec;
-	struct device_node *root;
 	struct device_node *syscon;
 	struct device_node *ebi;
 	struct device *parent;
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
 	u32 ap_sc_id;
-	int err;
 	int i;
 
-	/* Here we create an SoC device for the root node */
+	syscon = of_find_matching_node(NULL, ap_syscon_match);
-	root = of_find_node_by_path("/");
-	if (!root)
-		return;
-
-	syscon = of_find_matching_node(root, ap_syscon_match);
 	if (!syscon)
 		return;
-	ebi = of_find_matching_node(root, ebi_match);
+	ebi = of_find_matching_node(NULL, ebi_match);
 	if (!ebi)
 		return;
 
@@ -509,19 +502,17 @@ static void __init ap_init_of(void)
 	if (!ebi_base)
 		return;
 
+	of_platform_populate(NULL, of_default_bus_match_table,
+			ap_auxdata_lookup, NULL);
+
 	ap_sc_id = readl(ap_syscon_base);
 
 	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
 		return;
 
-	err = of_property_read_string(root, "compatible",
+	soc_dev_attr->soc_id = "XVC";
-				      &soc_dev_attr->soc_id);
+	soc_dev_attr->machine = "Integrator/AP";
-	if (err)
-		return;
-	err = of_property_read_string(root, "model", &soc_dev_attr->machine);
-	if (err)
-		return;
 	soc_dev_attr->family = "Integrator";
 	soc_dev_attr->revision = kasprintf(GFP_KERNEL, "%c",
 					   'A' + (ap_sc_id & 0x0f));
@@ -536,9 +527,6 @@ static void __init ap_init_of(void)
 	parent = soc_device_to_device(soc_dev);
 	integrator_init_sysfs(parent, ap_sc_id);
 
-	of_platform_populate(root, of_default_bus_match_table,
-			ap_auxdata_lookup, parent);
-
 	sc_dec = readl(ap_syscon_base + INTEGRATOR_SC_DEC_OFFSET);
 	for (i = 0; i < 4; i++) {
 		struct lm_device *lmdev;

arch/arm/mach-integrator/integrator_cp.c

@@ -279,20 +279,13 @@ static const struct of_device_id intcp_syscon_match[] = {
 
 static void __init intcp_init_of(void)
 {
-	struct device_node *root;
 	struct device_node *cpcon;
 	struct device *parent;
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
 	u32 intcp_sc_id;
-	int err;
 
-	/* Here we create an SoC device for the root node */
+	cpcon = of_find_matching_node(NULL, intcp_syscon_match);
-	root = of_find_node_by_path("/");
-	if (!root)
-		return;
-
-	cpcon = of_find_matching_node(root, intcp_syscon_match);
 	if (!cpcon)
 		return;
 
@@ -300,19 +293,17 @@ static void __init intcp_init_of(void)
 	if (!intcp_con_base)
 		return;
 
+	of_platform_populate(NULL, of_default_bus_match_table,
+			     intcp_auxdata_lookup, NULL);
+
 	intcp_sc_id = readl(intcp_con_base);
 
 	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
 		return;
 
-	err = of_property_read_string(root, "compatible",
+	soc_dev_attr->soc_id = "XCV";
-				      &soc_dev_attr->soc_id);
+	soc_dev_attr->machine = "Integrator/CP";
-	if (err)
-		return;
-	err = of_property_read_string(root, "model", &soc_dev_attr->machine);
-	if (err)
-		return;
 	soc_dev_attr->family = "Integrator";
 	soc_dev_attr->revision = kasprintf(GFP_KERNEL, "%c",
 					   'A' + (intcp_sc_id & 0x0f));
@@ -326,8 +317,6 @@ static void __init intcp_init_of(void)
 
 	parent = soc_device_to_device(soc_dev);
 	integrator_init_sysfs(parent, intcp_sc_id);
-	of_platform_populate(root, of_default_bus_match_table,
-			intcp_auxdata_lookup, parent);
 }
 
 static const char * intcp_dt_board_compat[] = {

arch/arm/mach-mvebu/Kconfig

@@ -10,6 +10,7 @@ menuconfig ARCH_MVEBU
 	select ZONE_DMA if ARM_LPAE
 	select ARCH_REQUIRE_GPIOLIB
 	select PCI_QUIRKS if PCI
+	select OF_ADDRESS_PCI
 
 if ARCH_MVEBU
 
@@ -17,6 +18,7 @@ config MACH_MVEBU_V7
 	bool
 	select ARMADA_370_XP_TIMER
 	select CACHE_L2X0
+	select ARM_CPU_SUSPEND
 
 config MACH_ARMADA_370
 	bool "Marvell Armada 370 boards" if ARCH_MULTI_V7

arch/arm/mach-mvebu/Makefile

@@ -7,7 +7,7 @@ CFLAGS_pmsu.o			:= -march=armv7-a
 obj-y				 += system-controller.o mvebu-soc-id.o
 
 ifeq ($(CONFIG_MACH_MVEBU_V7),y)
-obj-y				 += cpu-reset.o board-v7.o coherency.o coherency_ll.o pmsu.o
+obj-y				 += cpu-reset.o board-v7.o coherency.o coherency_ll.o pmsu.o pmsu_ll.o
 obj-$(CONFIG_SMP)		 += platsmp.o headsmp.o platsmp-a9.o headsmp-a9.o
 obj-$(CONFIG_HOTPLUG_CPU)	 += hotplug.o
 endif

arch/arm/mach-mvebu/board-v7.c

@@ -23,6 +23,7 @@
 #include <linux/mbus.h>
 #include <linux/signal.h>
 #include <linux/slab.h>
+#include <linux/irqchip.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -71,17 +72,23 @@ static int armada_375_external_abort_wa(unsigned long addr, unsigned int fsr,
 	return 1;
 }
 
-static void __init mvebu_timer_and_clk_init(void)
+static void __init mvebu_init_irq(void)
 {
-	of_clk_init(NULL);
+	irqchip_init();
-	clocksource_of_init();
 	mvebu_scu_enable();
 	coherency_init();
 	BUG_ON(mvebu_mbus_dt_init(coherency_available()));
+}
 
-	if (of_machine_is_compatible("marvell,armada375"))
+static void __init external_abort_quirk(void)
-		hook_fault_code(16 + 6, armada_375_external_abort_wa, SIGBUS, 0,
+{
-				"imprecise external abort");
+	u32 dev, rev;
+
+	if (mvebu_get_soc_id(&dev, &rev) == 0 && rev > ARMADA_375_Z1_REV)
+		return;
+
+	hook_fault_code(16 + 6, armada_375_external_abort_wa, SIGBUS, 0,
+			"imprecise external abort");
 }
 
 static void __init i2c_quirk(void)
@@ -169,8 +176,10 @@ static void __init mvebu_dt_init(void)
 {
 	if (of_machine_is_compatible("plathome,openblocks-ax3-4"))
 		i2c_quirk();
-	if (of_machine_is_compatible("marvell,a375-db"))
+	if (of_machine_is_compatible("marvell,a375-db")) {
+		external_abort_quirk();
 		thermal_quirk();
+	}
 
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
@@ -185,7 +194,7 @@ DT_MACHINE_START(ARMADA_370_XP_DT, "Marvell Armada 370/XP (Device Tree)")
 	.l2c_aux_mask	= ~0,
 	.smp		= smp_ops(armada_xp_smp_ops),
 	.init_machine	= mvebu_dt_init,
-	.init_time	= mvebu_timer_and_clk_init,
+	.init_irq       = mvebu_init_irq,
 	.restart	= mvebu_restart,
 	.dt_compat	= armada_370_xp_dt_compat,
 MACHINE_END
@@ -198,7 +207,7 @@ static const char * const armada_375_dt_compat[] = {
 DT_MACHINE_START(ARMADA_375_DT, "Marvell Armada 375 (Device Tree)")
 	.l2c_aux_val	= 0,
 	.l2c_aux_mask	= ~0,
-	.init_time	= mvebu_timer_and_clk_init,
+	.init_irq       = mvebu_init_irq,
 	.init_machine	= mvebu_dt_init,
 	.restart	= mvebu_restart,
 	.dt_compat	= armada_375_dt_compat,
@@ -213,7 +222,7 @@ static const char * const armada_38x_dt_compat[] = {
 DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)")
 	.l2c_aux_val	= 0,
 	.l2c_aux_mask	= ~0,
-	.init_time	= mvebu_timer_and_clk_init,
+	.init_irq       = mvebu_init_irq,
 	.restart	= mvebu_restart,
 	.dt_compat	= armada_38x_dt_compat,
 MACHINE_END

arch/arm/mach-mvebu/pmsu.c

@@ -66,6 +66,8 @@ static void __iomem *pmsu_mp_base;
 extern void ll_disable_coherency(void);
 extern void ll_enable_coherency(void);
 
+extern void armada_370_xp_cpu_resume(void);
+
 static struct platform_device armada_xp_cpuidle_device = {
 	.name = "cpuidle-armada-370-xp",
 };
@@ -140,13 +142,6 @@ static void armada_370_xp_pmsu_enable_l2_powerdown_onidle(void)
 	writel(reg, pmsu_mp_base + L2C_NFABRIC_PM_CTL);
 }
 
-static void armada_370_xp_cpu_resume(void)
-{
-	asm volatile("bl    ll_add_cpu_to_smp_group\n\t"
-		     "bl    ll_enable_coherency\n\t"
-		     "b	    cpu_resume\n\t");
-}
-
 /* No locking is needed because we only access per-CPU registers */
 void armada_370_xp_pmsu_idle_prepare(bool deepidle)
 {

arch/arm/mach-mvebu/pmsu_ll.S

@@ -0,0 +1,25 @@
+/*
+ * Copyright (C) 2014 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Gregory Clement <gregory.clement@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * This is the entry point through which CPUs exiting cpuidle deep
+ * idle state are going.
+ */
+ENTRY(armada_370_xp_cpu_resume)
+ARM_BE8(setend	be )			@ go BE8 if entered LE
+	bl	ll_add_cpu_to_smp_group
+	bl	ll_enable_coherency
+	b	cpu_resume
+ENDPROC(armada_370_xp_cpu_resume)
+

arch/arm/mach-omap2/Kconfig

@@ -34,8 +34,8 @@ config ARCH_OMAP4
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select OMAP_INTERCONNECT
-	select PL310_ERRATA_588369
+	select PL310_ERRATA_588369 if CACHE_L2X0
-	select PL310_ERRATA_727915
+	select PL310_ERRATA_727915 if CACHE_L2X0
 	select PM_OPP if PM
 	select PM_RUNTIME if CPU_IDLE
 	select ARM_ERRATA_754322

arch/arm/mach-omap2/Makefile

@@ -110,14 +110,16 @@ obj-y					+= prm_common.o cm_common.o
 obj-$(CONFIG_ARCH_OMAP2)		+= prm2xxx_3xxx.o prm2xxx.o cm2xxx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= prm2xxx_3xxx.o prm3xxx.o cm3xxx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= vc3xxx_data.o vp3xxx_data.o
-obj-$(CONFIG_SOC_AM33XX)		+= prm33xx.o cm33xx.o
 omap-prcm-4-5-common			=  cminst44xx.o cm44xx.o prm44xx.o \
 					   prcm_mpu44xx.o prminst44xx.o \
 					   vc44xx_data.o vp44xx_data.o
 obj-$(CONFIG_ARCH_OMAP4)		+= $(omap-prcm-4-5-common)
 obj-$(CONFIG_SOC_OMAP5)			+= $(omap-prcm-4-5-common)
 obj-$(CONFIG_SOC_DRA7XX)		+= $(omap-prcm-4-5-common)
-obj-$(CONFIG_SOC_AM43XX)		+= $(omap-prcm-4-5-common)
+am33xx-43xx-prcm-common			+= prm33xx.o cm33xx.o
+obj-$(CONFIG_SOC_AM33XX)		+= $(am33xx-43xx-prcm-common)
+obj-$(CONFIG_SOC_AM43XX)		+= $(omap-prcm-4-5-common) \
+					   $(am33xx-43xx-prcm-common)
 
 # OMAP voltage domains
 voltagedomain-common			:= voltage.o vc.o vp.o

arch/arm/mach-omap2/cm33xx.h

@@ -380,7 +380,7 @@ void am33xx_cm_clkdm_disable_hwsup(u16 inst, u16 cdoffs);
 void am33xx_cm_clkdm_force_sleep(u16 inst, u16 cdoffs);
 void am33xx_cm_clkdm_force_wakeup(u16 inst, u16 cdoffs);
 
-#ifdef CONFIG_SOC_AM33XX
+#if defined(CONFIG_SOC_AM33XX) || defined(CONFIG_SOC_AM43XX)
 extern int am33xx_cm_wait_module_idle(u16 inst, s16 cdoffs,
 					u16 clkctrl_offs);
 extern void am33xx_cm_module_enable(u8 mode, u16 inst, s16 cdoffs,

arch/arm/mach-omap2/common.h

@@ -248,7 +248,6 @@ static inline void __iomem *omap4_get_scu_base(void)
 }
 #endif
 
-extern void __init gic_init_irq(void);
 extern void gic_dist_disable(void);
 extern void gic_dist_enable(void);
 extern bool gic_dist_disabled(void);

arch/arm/mach-omap2/id.c

@@ -649,6 +649,18 @@ void __init dra7xxx_check_revision(void)
 		}
 		break;
 
+	case 0xb9bc:
+		switch (rev) {
+		case 0:
+			omap_revision = DRA722_REV_ES1_0;
+			break;
+		default:
+			/* If we have no new revisions */
+			omap_revision = DRA722_REV_ES1_0;
+			break;
+		}
+		break;
+
 	default:
 		/* Unknown default to latest silicon rev as default*/
 		pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%d)\n",

arch/arm/mach-omap2/mux.c

@@ -183,8 +183,10 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition,
 		m0_entry = mux->muxnames[0];
 
 		/* First check for full name in mode0.muxmode format */
-		if (mode0_len && strncmp(muxname, m0_entry, mode0_len))
+		if (mode0_len)
-			continue;
+			if (strncmp(muxname, m0_entry, mode0_len) ||
+			    (strlen(m0_entry) != mode0_len))
+				continue;
 
 		/* Then check for muxmode only */
 		for (i = 0; i < OMAP_MUX_NR_MODES; i++) {

arch/arm/mach-omap2/omap4-common.c

@@ -102,26 +102,6 @@ void __init omap_barriers_init(void)
 {}
 #endif
 
-void __init gic_init_irq(void)
-{
-	void __iomem *omap_irq_base;
-
-	/* Static mapping, never released */
-	gic_dist_base_addr = ioremap(OMAP44XX_GIC_DIST_BASE, SZ_4K);
-	BUG_ON(!gic_dist_base_addr);
-
-	twd_base = ioremap(OMAP44XX_LOCAL_TWD_BASE, SZ_4K);
-	BUG_ON(!twd_base);
-
-	/* Static mapping, never released */
-	omap_irq_base = ioremap(OMAP44XX_GIC_CPU_BASE, SZ_512);
-	BUG_ON(!omap_irq_base);
-
-	omap_wakeupgen_init();
-
-	gic_init(0, 29, gic_dist_base_addr, omap_irq_base);
-}
-
 void gic_dist_disable(void)
 {
 	if (gic_dist_base_addr)

arch/arm/mach-omap2/omap_hwmod.c

@@ -4251,9 +4251,9 @@ void __init omap_hwmod_init(void)
 		soc_ops.enable_module = _omap4_enable_module;
 		soc_ops.disable_module = _omap4_disable_module;
 		soc_ops.wait_target_ready = _omap4_wait_target_ready;
-		soc_ops.assert_hardreset = _omap4_assert_hardreset;
+		soc_ops.assert_hardreset = _am33xx_assert_hardreset;
-		soc_ops.deassert_hardreset = _omap4_deassert_hardreset;
+		soc_ops.deassert_hardreset = _am33xx_deassert_hardreset;
-		soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
+		soc_ops.is_hardreset_asserted = _am33xx_is_hardreset_asserted;
 		soc_ops.init_clkdm = _init_clkdm;
 	} else if (soc_is_am33xx()) {
 		soc_ops.enable_module = _am33xx_enable_module;

arch/arm/mach-omap2/omap_hwmod_54xx_data.c

@@ -2020,6 +2020,77 @@ static struct omap_hwmod omap54xx_wd_timer2_hwmod = {
 	},
 };
 
+/*
+ * 'ocp2scp' class
+ * bridge to transform ocp interface protocol to scp (serial control port)
+ * protocol
+ */
+/* ocp2scp3 */
+static struct omap_hwmod omap54xx_ocp2scp3_hwmod;
+/* l4_cfg -> ocp2scp3 */
+static struct omap_hwmod_ocp_if omap54xx_l4_cfg__ocp2scp3 = {
+	.master		= &omap54xx_l4_cfg_hwmod,
+	.slave		= &omap54xx_ocp2scp3_hwmod,
+	.clk		= "l4_root_clk_div",
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+static struct omap_hwmod omap54xx_ocp2scp3_hwmod = {
+	.name		= "ocp2scp3",
+	.class		= &omap54xx_ocp2scp_hwmod_class,
+	.clkdm_name	= "l3init_clkdm",
+	.prcm = {
+		.omap4 = {
+			.clkctrl_offs = OMAP54XX_CM_L3INIT_OCP2SCP3_CLKCTRL_OFFSET,
+			.context_offs = OMAP54XX_RM_L3INIT_OCP2SCP3_CONTEXT_OFFSET,
+			.modulemode   = MODULEMODE_HWCTRL,
+		},
+	},
+};
+
+/*
+ * 'sata' class
+ * sata:  serial ata interface  gen2 compliant   ( 1 rx/ 1 tx)
+ */
+
+static struct omap_hwmod_class_sysconfig omap54xx_sata_sysc = {
+	.sysc_offs	= 0x0000,
+	.sysc_flags	= (SYSC_HAS_MIDLEMODE | SYSC_HAS_SIDLEMODE),
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
+			   SIDLE_SMART_WKUP | MSTANDBY_FORCE | MSTANDBY_NO |
+			   MSTANDBY_SMART | MSTANDBY_SMART_WKUP),
+	.sysc_fields	= &omap_hwmod_sysc_type2,
+};
+
+static struct omap_hwmod_class omap54xx_sata_hwmod_class = {
+	.name	= "sata",
+	.sysc	= &omap54xx_sata_sysc,
+};
+
+/* sata */
+static struct omap_hwmod omap54xx_sata_hwmod = {
+	.name		= "sata",
+	.class		= &omap54xx_sata_hwmod_class,
+	.clkdm_name	= "l3init_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY,
+	.main_clk	= "func_48m_fclk",
+	.mpu_rt_idx	= 1,
+	.prcm = {
+		.omap4 = {
+			.clkctrl_offs = OMAP54XX_CM_L3INIT_SATA_CLKCTRL_OFFSET,
+			.context_offs = OMAP54XX_RM_L3INIT_SATA_CONTEXT_OFFSET,
+			.modulemode   = MODULEMODE_SWCTRL,
+		},
+	},
+};
+
+/* l4_cfg -> sata */
+static struct omap_hwmod_ocp_if omap54xx_l4_cfg__sata = {
+	.master		= &omap54xx_l4_cfg_hwmod,
+	.slave		= &omap54xx_sata_hwmod,
+	.clk		= "l3_iclk_div",
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
 
 /*
  * Interfaces
@@ -2765,6 +2836,8 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = {
 	&omap54xx_l4_cfg__usb_tll_hs,
 	&omap54xx_l4_cfg__usb_otg_ss,
 	&omap54xx_l4_wkup__wd_timer2,
+	&omap54xx_l4_cfg__ocp2scp3,
+	&omap54xx_l4_cfg__sata,
 	NULL,
 };
 

arch/arm/mach-omap2/soc.h

@@ -462,6 +462,7 @@ IS_OMAP_TYPE(3430, 0x3430)
 #define DRA7XX_CLASS		0x07000000
 #define DRA752_REV_ES1_0	(DRA7XX_CLASS | (0x52 << 16) | (0x10 << 8))
 #define DRA752_REV_ES1_1	(DRA7XX_CLASS | (0x52 << 16) | (0x11 << 8))
+#define DRA722_REV_ES1_0	(DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8))
 
 void omap2xxx_check_revision(void);
 void omap3xxx_check_revision(void);

arch/arm/mach-sa1100/collie.c

@@ -329,6 +329,11 @@ static struct mtd_partition collie_partitions[] = {
 		.name		= "rootfs",
 		.offset 	= MTDPART_OFS_APPEND,
 		.size		= 0x00e20000,
+	}, {
+		.name		= "bootblock",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 0x00020000,
+		.mask_flags	= MTD_WRITEABLE
 	}
 };
 
@@ -356,7 +361,7 @@ static void collie_flash_exit(void)
 }
 
 static struct flash_platform_data collie_flash_data = {
-	.map_name	= "jedec_probe",
+	.map_name	= "cfi_probe",
 	.init		= collie_flash_init,
 	.set_vpp	= collie_set_vpp,
 	.exit		= collie_flash_exit,

arch/arm/mach-sti/Kconfig

@@ -11,8 +11,8 @@ menuconfig ARCH_STI
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369 if SMP
 	select ARM_ERRATA_775420
-	select PL310_ERRATA_753970 if CACHE_PL310
+	select PL310_ERRATA_753970 if CACHE_L2X0
-	select PL310_ERRATA_769419 if CACHE_PL310
+	select PL310_ERRATA_769419 if CACHE_L2X0
 	help
 	  Include support for STiH41x SOCs like STiH415/416 using the device tree
 	  for discovery

arch/arm/mach-sunxi/sunxi.c

@@ -12,8 +12,81 @@
 
 #include <linux/clk-provider.h>
 #include <linux/clocksource.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/io.h>
+#include <linux/reboot.h>
 
 #include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/system_misc.h>
+
+#define SUN4I_WATCHDOG_CTRL_REG		0x00
+#define SUN4I_WATCHDOG_CTRL_RESTART		BIT(0)
+#define SUN4I_WATCHDOG_MODE_REG		0x04
+#define SUN4I_WATCHDOG_MODE_ENABLE		BIT(0)
+#define SUN4I_WATCHDOG_MODE_RESET_ENABLE	BIT(1)
+
+#define SUN6I_WATCHDOG1_IRQ_REG		0x00
+#define SUN6I_WATCHDOG1_CTRL_REG	0x10
+#define SUN6I_WATCHDOG1_CTRL_RESTART		BIT(0)
+#define SUN6I_WATCHDOG1_CONFIG_REG	0x14
+#define SUN6I_WATCHDOG1_CONFIG_RESTART		BIT(0)
+#define SUN6I_WATCHDOG1_CONFIG_IRQ		BIT(1)
+#define SUN6I_WATCHDOG1_MODE_REG	0x18
+#define SUN6I_WATCHDOG1_MODE_ENABLE		BIT(0)
+
+static void __iomem *wdt_base;
+
+static void sun4i_restart(enum reboot_mode mode, const char *cmd)
+{
+	if (!wdt_base)
+		return;
+
+	/* Enable timer and set reset bit in the watchdog */
+	writel(SUN4I_WATCHDOG_MODE_ENABLE | SUN4I_WATCHDOG_MODE_RESET_ENABLE,
+	       wdt_base + SUN4I_WATCHDOG_MODE_REG);
+
+	/*
+	 * Restart the watchdog. The default (and lowest) interval
+	 * value for the watchdog is 0.5s.
+	 */
+	writel(SUN4I_WATCHDOG_CTRL_RESTART, wdt_base + SUN4I_WATCHDOG_CTRL_REG);
+
+	while (1) {
+		mdelay(5);
+		writel(SUN4I_WATCHDOG_MODE_ENABLE | SUN4I_WATCHDOG_MODE_RESET_ENABLE,
+		       wdt_base + SUN4I_WATCHDOG_MODE_REG);
+	}
+}
+
+static struct of_device_id sunxi_restart_ids[] = {
+	{ .compatible = "allwinner,sun4i-a10-wdt" },
+	{ /*sentinel*/ }
+};
+
+static void sunxi_setup_restart(void)
+{
+	struct device_node *np;
+
+	np = of_find_matching_node(NULL, sunxi_restart_ids);
+	if (WARN(!np, "unable to setup watchdog restart"))
+		return;
+
+	wdt_base = of_iomap(np, 0);
+	WARN(!wdt_base, "failed to map watchdog base address");
+}
+
+static void __init sunxi_dt_init(void)
+{
+	sunxi_setup_restart();
+
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
 
 static const char * const sunxi_board_dt_compat[] = {
 	"allwinner,sun4i-a10",
@@ -23,7 +96,9 @@ static const char * const sunxi_board_dt_compat[] = {
 };
 
 DT_MACHINE_START(SUNXI_DT, "Allwinner A1X (Device Tree)")
+	.init_machine	= sunxi_dt_init,
 	.dt_compat	= sunxi_board_dt_compat,
+	.restart	= sun4i_restart,
 MACHINE_END
 
 static const char * const sun6i_board_dt_compat[] = {
@@ -51,5 +126,7 @@ static const char * const sun7i_board_dt_compat[] = {
 };
 
 DT_MACHINE_START(SUN7I_DT, "Allwinner sun7i (A20) Family")
+	.init_machine	= sunxi_dt_init,
 	.dt_compat	= sun7i_board_dt_compat,
+	.restart	= sun4i_restart,
 MACHINE_END

arch/arm/mach-ux500/Kconfig

@@ -15,7 +15,7 @@ menuconfig ARCH_U8500
 	select PINCTRL
 	select PINCTRL_ABX500
 	select PINCTRL_NOMADIK
-	select PL310_ERRATA_753970 if CACHE_PL310
+	select PL310_ERRATA_753970 if CACHE_L2X0
 	help
 	  Support for ST-Ericsson's Ux500 architecture
 

arch/arm/mach-vexpress/Kconfig

@@ -43,7 +43,7 @@ config ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
 	bool "Enable A5 and A9 only errata work-arounds"
 	default y
 	select ARM_ERRATA_720789
-	select PL310_ERRATA_753970 if CACHE_PL310
+	select PL310_ERRATA_753970 if CACHE_L2X0
 	help
 	  Provides common dependencies for Versatile Express platforms
 	  based on Cortex-A5 and Cortex-A9 processors. In order to

arch/arm/mm/Kconfig

@@ -889,9 +889,10 @@ config CACHE_L2X0
 	help
 	  This option enables the L2x0 PrimeCell.
 
+if CACHE_L2X0
+
 config CACHE_PL310
 	bool
-	depends on CACHE_L2X0
 	default y if CPU_V7 && !(CPU_V6 || CPU_V6K)
 	help
 	  This option enables optimisations for the PL310 cache
@@ -899,7 +900,6 @@ config CACHE_PL310
 
 config PL310_ERRATA_588369
 	bool "PL310 errata: Clean & Invalidate maintenance operations do not invalidate clean lines"
-	depends on CACHE_L2X0
 	help
 	   The PL310 L2 cache controller implements three types of Clean &
 	   Invalidate maintenance operations: by Physical Address
@@ -912,7 +912,6 @@ config PL310_ERRATA_588369
 
 config PL310_ERRATA_727915
 	bool "PL310 errata: Background Clean & Invalidate by Way operation can cause data corruption"
-	depends on CACHE_L2X0
 	help
 	  PL310 implements the Clean & Invalidate by Way L2 cache maintenance
 	  operation (offset 0x7FC). This operation runs in background so that
@@ -923,7 +922,6 @@ config PL310_ERRATA_727915
 
 config PL310_ERRATA_753970
 	bool "PL310 errata: cache sync operation may be faulty"
-	depends on CACHE_PL310
 	help
 	  This option enables the workaround for the 753970 PL310 (r3p0) erratum.
 
@@ -938,7 +936,6 @@ config PL310_ERRATA_753970
 
 config PL310_ERRATA_769419
 	bool "PL310 errata: no automatic Store Buffer drain"
-	depends on CACHE_L2X0
 	help
 	  On revisions of the PL310 prior to r3p2, the Store Buffer does
 	  not automatically drain. This can cause normal, non-cacheable
@@ -948,6 +945,8 @@ config PL310_ERRATA_769419
 	  on systems with an outer cache, the store buffer is drained
 	  explicitly.
 
+endif
+
 config CACHE_TAUROS2
 	bool "Enable the Tauros2 L2 cache controller"
 	depends on (ARCH_DOVE || ARCH_MMP || CPU_PJ4)

arch/arm/mm/cache-l2x0.c

@@ -1068,6 +1068,33 @@ static const struct l2c_init_data of_l2c310_data __initconst = {
 	},
 };
 
+/*
+ * This is a variant of the of_l2c310_data with .sync set to
+ * NULL. Outer sync operations are not needed when the system is I/O
+ * coherent, and potentially harmful in certain situations (PCIe/PL310
+ * deadlock on Armada 375/38x due to hardware I/O coherency). The
+ * other operations are kept because they are infrequent (therefore do
+ * not cause the deadlock in practice) and needed for secondary CPU
+ * boot and other power management activities.
+ */
+static const struct l2c_init_data of_l2c310_coherent_data __initconst = {
+	.type = "L2C-310 Coherent",
+	.way_size_0 = SZ_8K,
+	.num_lock = 8,
+	.of_parse = l2c310_of_parse,
+	.enable = l2c310_enable,
+	.fixup = l2c310_fixup,
+	.save  = l2c310_save,
+	.outer_cache = {
+		.inv_range   = l2c210_inv_range,
+		.clean_range = l2c210_clean_range,
+		.flush_range = l2c210_flush_range,
+		.flush_all   = l2c210_flush_all,
+		.disable     = l2c310_disable,
+		.resume      = l2c310_resume,
+	},
+};
+
 /*
  * Note that the end addresses passed to Linux primitives are
  * noninclusive, while the hardware cache range operations use
@@ -1487,6 +1514,10 @@ int __init l2x0_of_init(u32 aux_val, u32 aux_mask)
 
 	data = of_match_node(l2x0_ids, np)->data;
 
+	if (of_device_is_compatible(np, "arm,pl310-cache") &&
+	    of_property_read_bool(np, "arm,io-coherent"))
+		data = &of_l2c310_coherent_data;
+
 	old_aux = readl_relaxed(l2x0_base + L2X0_AUX_CTRL);
 	if (old_aux != ((old_aux & aux_mask) | aux_val)) {
 		pr_warn("L2C: platform modifies aux control register: 0x%08x -> 0x%08x\n",

arch/arm/mm/nommu.c

@@ -300,6 +300,7 @@ void __init sanity_check_meminfo(void)
 	sanity_check_meminfo_mpu();
 	end = memblock_end_of_DRAM();
 	high_memory = __va(end - 1) + 1;
+	memblock_set_current_limit(end);
 }
 
 /*