The patch titled "ath9k: Add new file init.c" shuffled some code
around but in dong so for some reason also removed the revision
check for disablign power save. Add this revision check again
so we can get power save re-enabled again by default on cards
newer than AR5416 and AR5418.
$ git describe --contains 556242049c
v2.6.34-rc1~233^2~49^2~343
This patch has fixes for stable kernels [2.6.34+].
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch:
commit 293dc5dfdb
Author: Gabor Juhos <juhosg@openwrt.org>
Date: Fri Jun 19 12:17:48 2009 +0200
ath9k: remove ath_rx_ps_back_to_sleep helper
This helper only clears the SC_OP_WAIT_FOR_{BEACON,CAB} flags.
Remove it and clear these flags directly in the approptiate
places instead.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
introduced a regression which forgot to lift the beacon flag
after we received all broadcast and multicast data. This meant
we never went to sleep consuming about ~650mW on idle. This pretty
much broke power save completely.
This patch has fixes for stable kernels [2.6.32+].
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Sameer Nanda <snanda@google.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k's entire logic with SC_OP_SCANNING is incorrect due to the
way mac80211 currently implements the scan complete callback and
we handle it in ath9k. This patch removes the flag completely in
preference for the SC_OP_OFFCHANNEL which is really what we wanted.
The scanning flag was used to ensure we reset ANI to the old values
when we go back to the home channel, but if we are offchannel we
use some defaults. The flag was also used to re-enable the TX monitor.
Without this patch we simply never re-enabled ANI and the TX monitor
after going offchannel. This means that after one background
scan we are prone to noise issues and if we had a TX hang we would
not recover. To get this to work properly we must enable ANI after
we have configured the beacon timers, otherwise hardware acts really
oddly.
This patch has stable fixes which apply down to [2.6.36+], there
*may* be a to fix this on older kernels but requires a bit of
work since this patch relies on the new mac80211 flag
IEEE80211_CONF_OFFCHANNEL which was introduced as of 2.6.36.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we return to the home channel we were never reseting our beacon
timers, this was casued by the fact that the scanning flag was still
on even after we returned to our home channel. There are also other
reasons why we would get a reset and if we are not off channel
we always need to resynch our beacon timers, because a reset will
clear them.
This bug is a regression introduced on 2.6.36. The order of the
changes are as follows:
5ee08656 - Sat Jul 31 - ath9k: prevent calibration during off-channel activity
a0daa0e7 - Tue Jul 27 - Revert "mac80211: fix sw scan bracketing"
543708be - Fri Jun 18 - mac80211: fix sw scan bracketing
mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
--contains 5ee0865615
v2.6.36-rc1~43^2~34^2~22
mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
--contains a0daa0e759
v2.6.36-rc1~571^2~64^2~13
mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
--contains 543708be32
v2.6.36-rc1~571^2~107^2~187
So 5ee08656 would have worked if a0daa0e7 was not committed but
it was so this means 5ee08656 was broken since it assumed that
when we were in the channel change routine the scan flag would
be lifted. As it turns out the scan flag will be set when we
are already on the home channel.
For more details refer to:
http://code.google.com/p/chromium-os/issues/detail?id=5715
These issues will need to be considered for our solution on
reshifting the scan complete callback location on mac80211 on
current development kernel work.
This patch has stable fixes which apply down to [2.6.36+]
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k has a race on putting the chip into network sleep and
having registers read from hardware. The race occurs because
although ath9k_ps_restore() locks its own callers it makes use
of some variables which get altered in the driver at different
code paths. The variables are the ps_enabled and ps_flags.
This is easily reprodicible in large network environments when
roaming with the wpa_supplicant simple bgscan. You'd get some
0xdeadbeef read out on certain registers such as:
ath: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000 != 0x00000000
ath: RX failed to go idle in 10 ms RXSM=0xdeadbeef
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
ath: Chip reset failed
The fix is to protect the ath9k_config(hw, IEEE80211_CONF_CHANGE_PS)
calls with a spin_lock_irqsave() which will disable contendors for
these variables from interrupt context, timers, re-entry from mac80211
on the same callback, and most importantly from ath9k_ps_restore()
which is the only call which will put the device into network sleep.
There are quite a few threads and bug reports on these a few of them are:
https://bugs.launchpad.net/ubuntu/karmic/+source/linux/+bug/407040http://code.google.com/p/chromium-os/issues/detail?id=5709http://code.google.com/p/chromium-os/issues/detail?id=5943
Stable fixes apply to [2.6.32+]
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To optimize register read/write operations, the HTC firmwares were patched
to change EP3 and EP4 pipe types from Interrupt to Bulk. So register writes
are submitted as bulk urbs, but register reads are not. Also changing the
register read endpoint pipe as bulk type when URBs are filled improves the
register reads considerably which results in reduced scan time and CPU
utilization.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes following warning
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function 'ath9k_hw_def_get_num_ant_config'
drivers/net/wireless/ath/ath9k/eeprom_def.c:1425:47: warning: comparison
between 'enum ath9k_hal_freq_band' and 'enum ieee80211_band'
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/libertas/cfg.c
drivers/net/wireless/libertas/cfg.c:493:19: warning: cast to restricted __le16
CHECK drivers/net/wireless/libertas/mesh.c
drivers/net/wireless/libertas/mesh.c:577:16: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/mesh.c:577:16: expected restricted __le32 [addressable] [assigned] [usertype] id
drivers/net/wireless/libertas/mesh.c:577:16: got bool
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/ath/ath9k/recv.c:1341:6: warning: symbol 'ath_ant_div_conf_fast_divbias' was not declared. Should it be static?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: int enum nl80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: int enum ieee80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: int enum nl80211_band
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print raw and decoded rxfilter in debufs 'wiphy' file.
Also, move variable-length printouts to bottom of file to
make bounds checking easier.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there is more than one VIF, listen for all beacons
and ensure ATH9K_RX_FILTER_MCAST_BCAST_ALL is set.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use key management functions which have been moved to ath/key.c and remove
ath9k copies of these functions and other now unused definitions.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace ah_aes_support and ah_combined_mic with common ath_crypt_caps
ATH_CRYPT_CAP_CIPHER_AESCCM and ATH_CRYPT_CAP_MIC_COMBINED.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace common->splitmic with ATH_CRYPT_CAP_MIC_COMBINED flag.
splitmic has to be used when the ATH_CRYPT_CAP_MIC_COMBINED capability flag is
not set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the old ath5k key handling functions, since we now use the key
management in ath common.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use common ath key management functions in ath5k. This fixes problems with HW
encryption in AP mode, which was broken in the ath5k implementation.
Before (with the ath5k implementation) only one client could connect to the AP
using HW encryption and WPA. When a second client connected, the first client
was not able to send/receive any more packets. Because of the problems with HW
encryption, software encryption was always used in AP mode, which resulted in a
high CPU load (and/or low thruput) on embedded devices. Instead of trying to
fix the implementation in ath5k it makes more sense to share the code with
ath9k.
This also enables HW encryption for AP mode again.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copied the key cache management functions from ath9k (common.c and hw.c) to
ath/key.c so we can use them from ath5k, later.
Minor changes have been made:
- renamed ath9k_* to ath_*
- replaced ah->caps.keycache_size with common->keymax
- removed ATH9K_IS_MIC_ENABLED since it is always true.
- the AR_PCU_MIC_NEW_LOC_ENA flag is replaced with (splitmic == 0).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These were introduced in "wl1271: sdio: claim host only when doing IO"
drivers/net/wireless/wl12xx/wl1271_sdio.c: In function ‘wl1271_sdio_set_power’:
drivers/net/wireless/wl12xx/wl1271_sdio.c:193: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:195: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:186: warning: unused variable ‘func’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If AR_KeyMiss is set in the rx descriptor and AR_RxFrameOK is unset,
the hardware could not locate a valid key during a decryption attempt.
In this case, the frame must not be reported as decrypted, otherwise
mac80211 sees only random garbage.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the time the .add_interface driver op is called, the interface has not
been marked as running yet, so ieee80211_iterate_active_interfaces will
not pass it to the iterator function.
Because of this, the calculated BSSID mask is wrong, which breaks multi-BSS
operation.
Additionally, the current way of comparing all addresses against each other
is pointless, as the hardware only uses the hardware MAC address and the BSSID
mask for matching the destination address, so all the address array
reallocation is completely unnecessary.
This patch simplifies the logic by setting the initial mask bytes to 0xff
and removing all bits in the iterator call that don't match the hardware MAC
address. It also calls the iterator for the vif that was passed to
add_interface()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CPU consumption during the scan period is high, since
the register write go over Interrupt endpoint. On downloading
the firmware to the target, the USB descriptors are
'patched' to change the type of the endpoints from Interrupt
to Bulk.
With this fix, the CPU usage during a scan run comes down to
acceptable levels.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_wmi_ctrl_rx is racy with ath9k_wmi_tasklet on event notification
due to which the wmi_skb may be overwritten which leads to memory leak.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even is someone else complete scanning in mac80211, apply rxon and
tx power settings if gets scan complete notification from hardware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace IWL_DEBUG_{INFO,HC,RC} to IWL_DEBUG_SCAN in iwl-scan.c file. Add
some more IWL_DEBUG_SCAN messages. This will allow to fully debug
scanning using only IWL_DL_SCAN flag.
Also start one message sentence with capital letter, since that
convention in iwl-scan.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove redundant checks and use iwl_is_ready_rf().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we force scan complete at the end of iwl_scan_cancel_timeout
function. This cause race condition when we can get a new scan request
from mac80211 and complete it by iwl_bg_complete from older scan. Change
code to force scan complete only when really needed: device goes down,
interface is removed or scan timeout occurs.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assure we complete scan in mac80211 when we abort scanning (scan_abort
work) or scan timeout occurs (scan_check work). Currently
iwl_scan_cancel_timeout() procedure force scan finish in mac80211
at the end of timeout loop, so we can use it in proper work functions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we do not get notification from hardware about scan complete, after
timeout do mac80211 scan completion anyway. This assure we end scan
in case of firmware hung.
Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assure (partially) we call ieee80211_scan_completed() only once when
scan was requested from mac80211.
Code path that first clear STATUS_SCANNING bit is responsible to call
ieee80211_scan_completed(). Before the call, we check if mac80211
really request the scan.
Still persist some cases when we behave wrong, that will be addressed
in the next patches.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since on timeout version of iwl_scan_cancel procedure we can sleep,
do not have to schedule abort_scan work to begin and perform scanning,
can do this directly. Also now, as we do not queue abort_scan from
restart work anymore, we can queue abort_scan to priv->workqueue.
Don't drop mutex when waiting for scan complete. Use STATUS_HW_SCAN bit
to check if scanning is currently pending, because STATUS_SCANNING will
be cleared only with priv->mutex taken.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we are not able to send abort command to firmware, notify mac80211
that we complete scan, as we will newer do it lately. Check for all
possible errors that low level sending command procedure does not check,
to assure we catch all failures cases.
Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always cancel scan when stooping device and scan is currently pending,
we should newer have scan running after down device.
To assure we start scan cancel from restart work we have to schedule
abort_scan to different workqueue than priv->workqueue.
Patch fix not cancel scanning when restarting firmware, what is
one of the causes of wdev_cleanup_work warning (together with permanent
network connection lost) reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the scan completed flags handling so that we
can notify mac80211 about aborted scans with the
correct status. Also queue the scan_completed work
before the BT status update so that it won't see
the bits still set (unless a new scan was started
in which case that's fine.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than duplicating all the checks and even
in case of errors accepting the scan request
from mac80211, we can push the checks to the
caller and in all error cases reject the scan
request right away (rather than accepting and
then saying it was aborted).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a number of conf variables that are
unused, remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace (sizeof(ofdm_level_table)/sizeof(ofdm_level_table[0]) with
ARRAY_SIZE(ofdm_level_table), and (sizeof(cck_level_table)/
sizeof(cck_level_table[0]) with ARRAY_SIZE(cck_level_table) in
drivers/net/wireless/ath/ath9k/ani.c
Signed-off-by: Nikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't generate calibration errors messages when not needed.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a typo introduced in "rt2x00: Add helper function for reporting tx
status" that results in an oops in rt2x00lib_txdone.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're handling both, the CSR_BEACON_DONE and the CSR_TWAKEUP interrupts
in rt61pci. However, these interrupts are masked out by default. Fix
this.
Found via pure code inspection.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't use all available interrupts in rt2800pci. Mask out all unused
interrupts to avoid waking up without having anything to do.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously rt2x00 was always updating all erp related config variables
even though mac80211 might only have changed one. Hence, pass the
changed flags to the config_erp driver callback so that the driver
can limit the changes to the correct values.
This fixes an issue in AP mode where the beacon interval is not
initialized (and thus zero) but still sent to the hardware causing an
interrupt storm on rt2800pci hanging the system.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we're not using the AMPDU_BA_WINSIZE register to force the BlockAck
window size (we specify it in every TXWI) we should initialize it to 0.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The test if antenna diversity is at all enabled uses a local variable
'flags' to prepare the test condition, but uses 'ant->flags' when the test
is evaluated. The effect is that the diversity evaluation will never start.
I can see two solutions, use the 'flag' in the test condition or revert the
local flag change. My attached patch took alternative two.
Then the evaluation start but it will still not switch antenna. The problem
is a code section in rt2x00lib_config_antenna (). The effect of that code
section is that any change the diversity function perform will be
effectively shorten and no antenna selection command issued. The attached
patch will filter out any ANTENNA_SW_DIVERSITY setting but forward all
other
Signed-off-by: Lars Ericsson <lars_ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To reduce scan time, enable fastcc for AR7010
(fastcc == fast channel change -- JWL)
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not maintain a persistent sdio_claim_host state. Instead,
claim host before doing IO and release host soon after.
This fixes several mmc deadlock scenarios, e.g. during
suspend/resume.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez