AR_AN_SYNTH9 is in the analog shift register range and thus needs to be
written using the ath9k_hw_analog_shift_rmw function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the proper masks for the register instead.
Fixes adding the (still unused) half/quarter PLL flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 belongs to diversity group 0 and AR9485 belongs to diversity
group 2. Based on the diversity group we configure certain antenna
diversity paramaters such as lna1_lna2_delta and fast diversity
bias values. For AR9485 we have some gain table parameter which
selects the gain table 0/1 for main and alternate antenna
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this is necessary to support Antenna diversity and combining in new chip
sets such as AR9485, previously Antenna diversity support is available
only in AR9285
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the AR9002, the spur frequency read from the EEPROM is mangled
before being compared against AR_NO_SPUR. This results in the driver
trying to set up the spur mitigation for bogus spurs, rather than
cleanly breaking out.
Signed-off-by: Brian Prodoehl <bprodoehl@nomadio.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after
REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that
makes keeping those ops separate rather pointless, as it only increases
code size and line number counts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds macros at certain places
which could be optimized for multiple register writes.
The performance of ath9k_htc improves considerably,
especially reducing the latency involved in a scan run.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PLL control computation used to program the AR_RTC_PLL_CONTROL
register varies between our harware so just add a private callback for it.
AR9003 will use its own callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PHY split is easier done in a few steps. First move
the RF ops to the private ops and rename them accordingly.
We split PHY stuff up first for the AR5008 and AR9002
families. There are some callbacks that AR9002 share
with the AR5008 familiy so we set those first, if AR9002
has some different callbacks it will override them upon
hardware init.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi