This patch configures data rates to firmware using bitrate mask
provided by cfg80211.
Earlier we used to only update band information in this handler
which will be used later for ibss network. Due to recent
modifications in ibss join code we don't need to do that.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mwifiex_set_rf_channel() ibss specific flags were unnecessarily
getting modified for infra and AP mode. This patch removes
mwifiex_set_rf_channel() function and adds equivalant code in infra,
ibss and AP path.
For ibss, now we are chosing band based on channel type and basic
rates provided in ibss join request. We can start ibss network in
A only, B only, G only, BG, BGN, AN mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Remove unnecessary wrapper functions.
2) Currently we don't have command to set Tx data rate, so
mwifiex_rate_ioctl_set_rate_value() function and related code
can be removed.
3) "ds_rate" filled by mwifiex_ret_tx_rate_cfg() is never used.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Recently we removed set_channel cfg80211 handler. Also, cfg80211
blocks ibss connection requests if ibss network is already started
/joined. Hence the code to restart ibss network in new channel
(mwifiex_drv_change_adhoc_chan() function) becomes redundant.
2) mwifiex_bss_set_channel() function is redundant. It does some
error checking and calculate adhoc start band and adhoc channel.
Cfg80211 already takes care of error checking and provides correct
channel information to the driver. Adhoc start band is already
calculated in mwifiex_set_rf_channel() function.
Other associated code is also removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enables user to set mode of Tx/Rx path using "iw set antenna"
command. For non MIMO chips, the command will be used for selecting
specific antenna or configuring antenna diversity mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parse WPS IEs from start_ap as well as change_beacon handlers
and set them to FW. Beacon IEs, Probe Response IEs and Assoc
Response IEs are parsed from beacon_data and set to FW with
related masks.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Being a fullmac driver, mwifiex takes care of populating
beacon, probe response, association response WPS IEs to firmware.
And firmware is responsible for constructing these frames.
Advertise this to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for change_beacon handler which is needed
for setting modified management IEs to driver and FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All IE buffers are freshly supplied. In such case, there is no need
to preserve earlier buffers with same management mask and index.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While Head/Tail IEs may contain RSN/WPA IEs which needs to be set
for all mgmt subtypes, beacon_ies, probe_resp_ies, assoc_resp_ies
are for specific mgmt subtypes. Move them to separate function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass cfg80211_beacon_data pointer instead of cfg80211_ap_settings.
While setting management IEs we only need cfg80211_beacon_data of
cfg80211_ap_settings which has Tail IE, Head IE and other IE elements.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we don't provide custom regulatory rules to cfg80211,
"chan->max_power" remains uninitialized (0dbm) and
"chan->max_reg_power" will contain maximum power for a channel
extracted from regulatory rules provided by CRDA; hence use
"chan->max_reg_power" in reg_notifier handler instead of
"chan->max_power" to set max_power in firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we don't support custom regulatory domains,
WIPHY_FLAG_CUSTOM_REGULATORY should not be enabled during wiphy
registration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"priv->max_tx_power_level" and "priv->min_tx_power_level" variables
are initialized to maximum and minimum power levels supported by
hardware by sending correct firmware command.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We miss to wakeup main thread after adding command to cmd pending
queue at follwing places. These commands are handled later when
main thread is woken up for handling an interrupt for sleep event
from firmware. This adds worst case delay of 50msec.
1) We don't wakeup main thread when asynchronous command is added
to cmd pending queue. Move queue_work() call from
mwifiex_wait_queue_complete() to mwifiex_send_cmd_async() to wakeup
main thread for sync as well as async commands.
2) Scan operation is triggered due to following reasons
a) request from user (ex. "iw scan" command)
b) Scan performed by driver internally.
In first case main thread is woken up when first scan command is
queued in cmd pending queue (we don't need to wakeup main thread for
subsequent scan commands, because they are queued in scan command
response handler), but it is not done for second case. queue_work()
is moved inside mwifiex_scan_networks() to handle both the cases.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free ap_custom_ie before return from function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FW will not explicitly notify about host sleep activation to the
host for USB and PCIe chipsets. Hence host should generate Host
Sleep Activated event as soon as Host Sleep parameters are
configured to FW successfully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a flaw in recently implemented logic to handle Tx traffic
and scan operation simultaneously. We missed to wakeup main thread
to handle Tx traffic if scan is delayed/aborted.
For some cards (SD8797, for example), firmware will send SLEEP event
if there is no activity for 50msec. While handling the SLEEP event,
main thread will be woken up and Tx packet gets sent hence. In worst
case Tx traffic will be delayed for 50msec.
For other cards, such as USB8797, firmware won't send SLEEP event.
So, Tx traffic gets stuck if no other event triggers the wakeup of
main thread.
This patch fixes above issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for parsing WPA IE from beacon parameter of
cfg80211_ap_settings and set it to FW.
WPA/WPA2 mixed mode is supported with this patch.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb allocated during initialisation is reused for receiving
commands/events by USB interface. We miss to reset skb->data in
failure cases. This patch takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures uniformity in event skb sent by interface code
(USB/PCIe/SDIO) which automatically fixes following bugs.
1) For USB interface, same buffer is reused for receiving cmd and
events from firmware. While handling events, we perform
skb_pull(skb, 4) to remove event header. Corresponding skb_push()
call is missing while submitting the buffer.
2) For PCIe interface, event skb is passed with event header.
Recently added uAP events EVENT_UAP_STA_ASSOC, EVENT_UAP_STA_DEAUTH
will not work for PCIe, as they assume event skb points to event body.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After association, STA will go through eapol handshake with WPS
enabled AP. It's observed that WPS handshake fails with some 11n
AP. The reason for the failure is that the eapol packet is sent
via 11n frame aggregation.
The eapol packet should be sent directly without 11n aggregation.
This patch fixes the problem by adding WPS session control while
dequeuing Tx packets for transmission.
Cc: "3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.
Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.
Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Cc: "3.0.y, 3.1.y, 3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for WEP open/shared encryption in AP mode.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enhance readability, create a separate function for parsing
WPA/WPA2 related parameters from cfg80211_ap_settings.
There is no functional change in this patch.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parse HT IE from cfg80211 and set HT capabilities accordingly
to FW. If HT IE is missing, 11n would be disabled in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds functionality to set channel info received from
cfg80211_ap_settings in start_ap handler.
Since set_channel cfg80211 handler has been removed and we need
not explicitely call mwifiex_uap_set_channel(); hence this
function definition is also removed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add_virtual_intf() needs to return an ERR_PTR(), instead of NULL,
on errors, otherwise cfg80211 will crash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running heavy traffic we stop the tx queue if the pending
packet count reaches certain threshold. Later, the tx queue should
be woken up as soon as the packet count falls below the threshold.
Current code wakes TX queue up on STA interface only. Removing the
check for STA interface will allow both STA and AP interfaces to
resume transmit when tx_pending count becomes low.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Test procedure:
1. Start AP with security setting (e.g. WPA2)
2. Stop AP
3. Start AP with open security
Here it's observed that privacy is enabled in beacons and
probe responses.
This patch fixes it by checking the privacy parameter from
cfg80211_ap_settings. If privacy is not set in cfg80211_ap_settings,
set open authentication and no encryption in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently 4 channels are scanned per scan command. if scan request
is issued by user during Tx traffic, radio will be out of channel
for "4 * per_chan_scan_time" for each scan command and will not be
able to receive Rx packets. This adds delay in data traffic. We can
minimize it by reducing number of channels scanned per scan command
in this scenario.
We can not always scan 1 channel per scan command due to limitation
of number of command buffers. So we add code to decide number of
channels scanned per scan command in associated state.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If scan operation is started when Tx traffic is already running,
driver locks Tx queue until it gets completed. With this logic
there is a delay for Tx packets.
This patch implements new approach to give Tx path higher priority
in this case. Driver internally sends multiple synchronous scan
commands to firmware when scan is requested by user. Now we will
make sure that Tx queue is empty everytime before sending next scan
command. If Tx queue isn't empty scan command will be postponsed by
20msec. This rule will be followed until Tx queue becomes empty or
timeout of 1 second happens. In case of timeout scan operation will
be aborted.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the scan time per channel for active scanning is set to
200ms. It takes quite a while to finsh scanning on all channels,
especially with a dual band configuration.
Change the per channel scan time settings to the following values:
passive scan: 110ms
active scan: 30ms
specific scan: 30ms
Above settings have been tested on x86 and arm platforms.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since mwifiex only supports managed and IBSS
modes, it doesn't need a set_channel call. The
callback might be called, but it won't matter
as nothing can use the channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete custom IEs set by start_ap cfg80211 handler when stop_ap
handler is called for AP interface.
IE index required for deletion is stored in mwifiex_private
structure.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds logic for setting tail beacon IE, probe response IE
and assoc response IE from cfg80211_ap_settings parameter of
start_ap handler into FW.
RSN IE is also retrieved from tail IE buffer and sent to firmware.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. support for setting custom IE from application hostapd etc.
Custom IE addition using auto-indexing and Custom IE deletion using
static indices (which are allocated during IE addition and stored in
driver) are supported.
2. Separate file for handling IE related execution.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes into account AP config_type
(bss config/custom ie config) while preparing AP
sys_configure command buffer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Support for parsing security related parameters from
cfg80211_ap_settings in start_ap cfg80211 handler
2. Conversion of these security information into FW understandle TLVs
and setting into FW thru sys_config command
3. key management is done on host. This ensures that FW forwards EAPOL
key packets to host instead of processing on its own.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added logic to handle AP event that are generated
by the firmware. As MLME/SME is implemented in the
firmware, events such as station association and
deauthentication, must be sent to userspace (hostapd)
for creating and deleting station database.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar