According to Bspec we need to
"Poll for PORT_REF_DW3_A grc_done == 1b"
only on ports B and C initialization sequence when
copying rcomp from port A.
So let's follow the spec and only poll for that case
and not on every port A initialization.
v2: Also remove the grc_done check from bxt_ddi_phy_is_enabled()
otherwise it might believe it is disabled and force it to re program.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479410256-25735-1-git-send-email-rodrigo.vivi@intel.com
Geminilake is mostly backwards compatible with broxton, so change most
of the IS_BROXTON() checks to IS_GEN9_LP(). Differences between the
platforms will be implemented in follow-up patches.
v2: Don't reuse broxton's path in intel_update_max_cdclk().
Don't set plane count as in broxton.
v3: Rebase
v4: Include the check intel_bios_is_port_hpd_inverted().
Commit message.
v5: Leave i915_dmc_info() out; glk's csr version != bxt's. (Rodrigo)
v6: Rebase.
v7: Convert a few mode IS_BROXTON() occurances in pps, ddi, dsi and pll
code. (Rodrigo)
v8: Squash a couple of DDI patches with more conversions. (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-2-git-send-email-ander.conselvan.de.oliveira@intel.com
The port registers related to the phys in broxton map to different
channels and specific phys. Make that mapping explicit.
v2: Pass enum dpio_phy to macros instead of mmio base. (Imre)
v3: Fix typo in macros. (Imre)
v4: Also change variables from u32 to enum dpio_phy. (Imre)
Remove leftovers from previous version. (Imre)
v5: Actually git add the changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476863940-6019-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Use struct bxt_ddi_phy_info to hold information of where the Rcomp
resistor is located, instead of hard coding it in the init sequence.
Note that this moves the enabling of the phy with the Rcomp resistor out
of the power well enable code. That should be safe since
bxt_ddi_phy_init() is called while the power domains lock is held, and
that is the only way that function gets called, so there is no
possibility of a concurrent phy enable caused by a power domain get
call.
v2: Replace comment about lock with lockdep_assert_held() (Imre)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/62d209950ad48484564f3e793cf247cf62572a39.1475770848.git-series.ander.conselvan.de.oliveira@intel.com
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
The code used by the DP and HDMI paths was very similar, so make them
share it. Note that this removes the write to signal level registers
from the HDMI pre pll enable path, but that's OK since those are set
in vlv_hdmi_pre_enable() function.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-9-git-send-email-ander.conselvan.de.oliveira@intel.com
The logic for setting signal levels is used for both HDMI and DP with
small variations. But it is similar enough to put behind a function
called from the encoders.
v2: Remove unrelated MST changes due to rebase fumble. (Jim Bride)
Fix typo in the commit message. (Jim Bride)
v3: Really fix the typo. (Jim)
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-8-git-send-email-ander.conselvan.de.oliveira@intel.com
The exact same code was used by HDMI and DP encoders, so move it to
intel_dpio_phy.c.
v2: Fix typo in the commit message. (Jim Bride)
v3: Call the new function chv_phy_post_pll_disable() instead of
chv_phy_post_disable(), as it should be called after the pll
is disabled. (Ville)
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-7-git-send-email-ander.conselvan.de.oliveira@intel.com
The only difference between the DP and HDMI versions was the lane count.
Since lane_count is now set appropriately for HDMI too, get rid of the
duplication and move this to intel_dpio_phy.c
v2: Don't move comments about 2nd common lane staying alive. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-6-git-send-email-ander.conselvan.de.oliveira@intel.com
Rodrigo Vivi