Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw writes.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
At the end of the delay loop timeout will always be zero
and hence the check for !timeout will always be true. Remove
the redundant check and the redundant return 0 at the end of
the function.
Fixes CoverityScan CID#1357168 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are 2 usage types (Magnetic Flux and Heading data field) for HID
compass sensor, thus the values of offset, scale, and sensitivity should
be separated according to their respective usage type. The changes made
are as below:
1. Hysteresis: A struct hid_sensor_common rot_attributes is created in
struct magn_3d_state to contain the sensitivity for IIO_ROT.
2. Scale: scale_pre_decml and scale_post_decml are separated for IIO_MAGN
and IIO_ROT.
3. Offset: Same as scale, value_offset is separated for IIO_MAGN and
IIO_ROT.
For sensitivity, HID_USAGE_SENSOR_ORIENT_MAGN_FLUX and
HID_USAGE_SENSOR_ORIENT_MAGN_HEADING are used for sensivitity fields based
on the HID Sensor Usages specifications. Hence, these changes are added on
the sensitivity field.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have #defines for all the individual sensor registers and
value/mask pairs #defined at the top of the file and used at
exactly one spot.
This is usually good if the #defines give a meaning to the
opaque magic numbers.
However in this case, the semantic meaning is inherent in the
name of the C99-addressable fields, and that means duplication
of information, and only makes the code hard to maintain since
you every time have to add a new #define AND update the site
where it is to be used.
Get rid of the #defines and just open code the values into the
appropriate struct elements. Make sure to explicitly address
the .hz and .value fields in the st_sensor_odr_avl struct
so that the meaning of all values is clear.
This patch is purely syntactic should have no semantic effect.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes two cases of 'cast to restricted __le16' as reported by sparse.
Signed-off-by: Ico Doornekamp <ico@pruts.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ak8974_configure() function is used only from the PM code,
but that can be hidden when CONFIG_PM is disabled:
drivers/iio/magnetometer/ak8974.c:201:12: error: 'ak8974_configure' defined but not used [-Werror=unused-function]
This replaces the #ifdef with a __maybe_unused annotation, which
will work correctly in all configurations and avoid the warning,
as the compiler can now see where ak8974_configure is called from.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7c94a8b2ee ("iio: magn: add a driver for AK8974")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a driver for the Asahi Kasei AK8974 and its sibling
AMI305 magnetometers. It was deployed on scale in 2009 on a
multitude of devices. It is distincly different from AK8973
and AK8975 and needs its own driver.
This patch is based on the long lost work of Samu Onkalo at Nokia,
who made a misc character device driver for the Maemo/MeeGo Nokia
devices, before the time of the IIO subsystem. It was mounted in e.g.
the Nokia N950, N8, N86, N97 etc. It is also mounted on the
ST-Ericsson HREF reference designs.
It works nicely in sysfs:
$ cat in_magn_x_raw && cat in_magn_y_raw && cat in_magn_z_raw
-55
-101
161
And with buffered reads using a simple HRTimer trigger:
$ generic_buffer -c10 -a -n ak8974 -t foo
iio device number being used is 3
iio trigger number being used is 2
No channels are enabled, enabling all channels
Enabling: in_magn_x_en
Enabling: in_magn_y_en
Enabling: in_magn_z_en
Enabling: in_timestamp_en
/sys/bus/iio/devices/iio:device3 foo
-58.000000 -102.000000 157.000000 946684970985321044
-60.000000 -98.000000 159.000000 946684971012237548
-60.000000 -106.000000 163.000000 946684971032257080
-62.000000 -94.000000 169.000000 946684971052185058
-58.000000 -98.000000 163.000000 946684971072204589
-54.000000 -100.000000 163.000000 946684971092224121
-53.000000 -103.000000 164.000000 946684971112731933
-50.000000 -102.000000 165.000000 946684971132232666
-61.000000 -101.000000 164.000000 946684971152191162
-57.000000 -99.000000 168.000000 946684971172210693
Disabling: in_magn_x_en
Disabling: in_magn_y_en
Disabling: in_magn_z_en
Disabling: in_timestamp_en
I cannot currently scale these raw values to gauss. This is
because of lack of documentation. I have sent a request for
a datasheet to Asahi Kasei.
The driver can optionally use a DRDY line IRQ to capture data,
else it will sleep and poll.
Cc: Samu Onkalo <samu.onkalo@intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds runtime PM support to the AK8975 driver. It solves two
problems:
- After reading the first value the chip was left in MODE_ONCE,
meaning (presumably) it may be consuming more power. Now the
runtime PM hooks kick in and set it to POWER_DOWN.
- Regulators were simply enabled and left on, making it
impossible to turn the power consuming regulators off because
of the increased refcount. We now disable the regulators at
autosuspend.
- We also handle system suspend: by using pm_runtime_force_suspend()
and pm_runtime_force_resume() from the system PM sleep hooks,
the runtime PM code is managing the power also for this case.
It is currently not completely optimal: when the system resumes
the AK8975 goes into active mode even if noone is going to use
it: currently the force calls need to be paired, but the runtime
PM people are working on making it possible to leave devices
runtime suspended when coming back from sleep.
Inspired by my work on the BH1780 light sensor driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The code was not powering the magnetometer down properly at
remove(): just cutting the regulators without first setting the
device in power off mode. Fix this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The datasheet actually specifies that we need to wait atleast
500us after powering on the device before trying to set mode.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move the regulator_get() calls directly into the probe() function,
keep only the power_on()/power_off() functions to flick the
regulators on/off.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The AK8975 has two power sources: Vdd (analog voltage supply)
and Vid (digital voltage supply). Optionally also obtain the Vid
supply regulator and enable it.
If an error occurs when enabling one of the regulators: bail out.
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Richard Leitner <dev@g0hl1n.net>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IS_ERR_OR_NULL() should never be used with regulators because
a NULL pointer may be a perfectly valid dummy regulator
We should always succeed to fetch and enable a regulator, but
it may be a dummy. That is fine, so bail out for any real
errors or probe deferrals
Include the error code in the warning print so we know what
kind of problem we're dealing with (for example it is nice to
see if it is a probe deferral).
As we will bail out of probe if the regulator is erroneous,
just issue regulator_disable() on the poweroff path: it will
succeed.
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Hq1a
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.8 cycle.
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
A slightly bumper set due to travel delaying the pull request and a fair few
issues with the recent merge window patches. Patches all over the place.
The st-sensors one is probably the most involved, but definitly solves the
issues seen. Note there are some other issues around that handler
(and the fact that a lot of boards tie a level interrupt chip to an
edge interrupt only irq chip). These are not regressions however, so
will turn up the slow route.
* core
- iio_trigger_attach_pollfunc had some really badly wrong error handling.
Another nasty triggered whilst chasing down issues with the st sensors
rework below.
* ad5592r
- fix an off by one error when allocating channels.
* am2315
- a stray mutex unlock before we ever take the lock.
* apds9960
- missing a parent in the driver model (which should be the i2c device).
Result is it doesn't turn up under /sys/bus/i2c/devices which some
userspace code uses for repeatable device identification.
* as3935
- ABI usage bug which meant a processed value was reported as raw. Now
reporting scale as well to ensure userspace has the info it needs.
- Don't return processed value via the buffer - it doesn't conform to
the ABI and will overflow in some cases.
- Fix a wrongly sized buffer which would overflow trashing part of the
stack. Also move it onto the heap as part of the fix.
* bh1780
- a missing return after write in debugfs lead to an incorrect read and
a null pointer dereference.
- dereferencing the wrong pointer in suspend and resume leading to
unpredictable results.
- assign a static name to avoid accidentally ending up with no name if
loaded via device tree.
* bmi160
- output data rate for the accelerometer was incorrectly reported. Fix it.
- writing the output data rate was also wrong due to reverse parameters.
* bmp280
- error message for wrong chip ID gave the wrong expected value.
* hdc100x
- mask for writing the integration time was wrong allowin g us to get
'stuck' in a particular value with no way back.
- temperature reported in celsius rather than millicelsius as per the
ABI.
- Get rid of some incorrect data shifting which lead to readings being
rather incorrect.
* max44000
- drop scale attribute for proximity as it is an unscaled value (depends
on what is in range rather than anything knowable at the detector).
* st-pressure
- ABI compliance fixes - units were wrong.
* st-sensors
- We introduced some nasty issues with the recent switch over to a
a somewhat threaded handler in that we broke using a software trigger
with these devices. Now do it properly. It's a larger patch than ideal
for a fix, but the logic is straight forward.
- Make sure the trigger is initialized before requesting the interrupt.
This matters now the interrupt can be shared. Before it was ugly and wrong
but short of flakey hardware could not be triggered.
- Hammer down the dataready pin at boot - otherwise with really
unlucky timing things could get interestingly wedged requiring a hard power
down of the chip.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EEPO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of iio fixes for the 4.7 cycle.
A slightly bumper set due to travel delaying the pull request and a fair few
issues with the recent merge window patches. Patches all over the place.
The st-sensors one is probably the most involved, but definitly solves the
issues seen. Note there are some other issues around that handler
(and the fact that a lot of boards tie a level interrupt chip to an
edge interrupt only irq chip). These are not regressions however, so
will turn up the slow route.
* core
- iio_trigger_attach_pollfunc had some really badly wrong error handling.
Another nasty triggered whilst chasing down issues with the st sensors
rework below.
* ad5592r
- fix an off by one error when allocating channels.
* am2315
- a stray mutex unlock before we ever take the lock.
* apds9960
- missing a parent in the driver model (which should be the i2c device).
Result is it doesn't turn up under /sys/bus/i2c/devices which some
userspace code uses for repeatable device identification.
* as3935
- ABI usage bug which meant a processed value was reported as raw. Now
reporting scale as well to ensure userspace has the info it needs.
- Don't return processed value via the buffer - it doesn't conform to
the ABI and will overflow in some cases.
- Fix a wrongly sized buffer which would overflow trashing part of the
stack. Also move it onto the heap as part of the fix.
* bh1780
- a missing return after write in debugfs lead to an incorrect read and
a null pointer dereference.
- dereferencing the wrong pointer in suspend and resume leading to
unpredictable results.
- assign a static name to avoid accidentally ending up with no name if
loaded via device tree.
* bmi160
- output data rate for the accelerometer was incorrectly reported. Fix it.
- writing the output data rate was also wrong due to reverse parameters.
* bmp280
- error message for wrong chip ID gave the wrong expected value.
* hdc100x
- mask for writing the integration time was wrong allowin g us to get
'stuck' in a particular value with no way back.
- temperature reported in celsius rather than millicelsius as per the
ABI.
- Get rid of some incorrect data shifting which lead to readings being
rather incorrect.
* max44000
- drop scale attribute for proximity as it is an unscaled value (depends
on what is in range rather than anything knowable at the detector).
* st-pressure
- ABI compliance fixes - units were wrong.
* st-sensors
- We introduced some nasty issues with the recent switch over to a
a somewhat threaded handler in that we broke using a software trigger
with these devices. Now do it properly. It's a larger patch than ideal
for a fix, but the logic is straight forward.
- Make sure the trigger is initialized before requesting the interrupt.
This matters now the interrupt can be shared. Before it was ugly and wrong
but short of flakey hardware could not be triggered.
- Hammer down the dataready pin at boot - otherwise with really
unlucky timing things could get interestingly wedged requiring a hard power
down of the chip.
commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded
("iio: st_sensors: verify interrupt event to status") caused
a regression when reading ST sensors from a HRTimer trigger
rather than the intrinsic interrupts: the HRTimer may
trigger faster than the sensor provides new values, and
as the check against new values available as a cause of
the interrupt trigger was done in the poll function,
this would bail out of the HRTimer interrupt with
IRQ_NONE.
So clearly we need to only check the new values available
from the proper interrupt handler and not from the poll
function, which should rather just read the raw values
from the registers, put them into the buffer and be happy.
To achieve this: switch the ST Sensors over to using a true
threaded interrupt handler.
In the interrupt thread, check if new values are available,
else yield to the (potential) next device on the same
interrupt line to check the registers. If the interrupt
was ours, proceed to poll the values.
Instead of relying on iio_trigger_generic_data_rdy_poll() as
a top half to wake up the thread that polls the sensor for
new data, have the thread call iio_trigger_poll_chained()
after determining that is is the proper source of the
interrupt. This is modelled on drivers/iio/accel/mma8452.c
which is already using a properly threaded interrupt handler.
In order to get the same precision in timestamps as
previously, where samples would be timestamped in the
poll function pf->timestamp when calling
iio_trigger_generic_data_rdy_poll() we introduce a
local timestamp in the sensor data, set it in the top half
(fastpath) of the interrupt handler and provide that to the
core when calling iio_push_to_buffers_with_timestamp().
Additionally: if the active scanmask is not set for the
sensor no IRQs should be enabled and we need to bail out
with IRQ_NONE. This can happen if spurious IRQs fire when
installing the threaded interrupt handler.
Tested with hard interrupt triggers on LIS331DL, then also
tested with hrtimers on the same sensor by creating a 75Hz
HRTimer and using it to poll the sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 97865fe413 ("iio: st_sensors: verify interrupt event to status")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
bmc150 driver supports also BMC156 and BMM150 chips.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure failure to enable power regulators is properly handled.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
BMM150 is register compatible with magnetometer part of
BMC156.
Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The device has simple 8-bit registers but the driver incorrectly uses
block or word reads without checking functionality bits.
Fix by using i2c_smbus_read_i2c_block_data_or_emulated instead of
i2c_smbus_read_i2c_block_data or i2c_smbus_read_word_data. This will
check functionality bits and use the fastest available transfer method.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zzV9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
Expose a rotation matrix to indicate userspace the chip orientation with
respect to the overall hardware system.
Matrix is retrieved from "in_mount_matrix". It is declared into ak8975 DTS
entry as a "mount-matrix" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is useful for easily adding SPI support in later patches.
Now bmc150_magn exports core functions to be used by I2C/SPI drivers
instances. For the moment only I2C driver is supported.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If i2c_device_id *id is NULL and acpi_match_device returns NULL too,
then chipset may be unitialized when accessing &ak_def_array[chipset] in
ak8975_probe. Therefore initialize chipset to AK_MAX_TYPE, which will
return an error when not changed.
This patch fixes the following maybe-uninitialized warning:
drivers/iio/magnetometer/ak8975.c: In function ‘ak8975_probe’:
drivers/iio/magnetometer/ak8975.c:788:14: warning: ‘chipset’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
data->def = &ak_def_array[chipset];
Signed-off-by: Richard Leitner <dev@g0hl1n.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In certain probe conditions the interrupt came right after registering
the handler causing a NULL pointer exception because of uninitialized
waitqueue:
$ udevadm trigger
i2c-gpio i2c-gpio-1: using pins 143 (SDA) and 144 (SCL)
i2c-gpio i2c-gpio-3: using pins 53 (SDA) and 52 (SCL)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = e8b38000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: snd_soc_i2s(+) i2c_gpio(+) snd_soc_idma snd_soc_s3c_dma snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer snd soundcore ac97_bus spi_s3c64xx pwm_samsung dwc2 exynos_adc phy_exynos_usb2 exynosdrm exynos_rng rng_core rtc_s3c
CPU: 0 PID: 717 Comm: data-provider-m Not tainted 4.6.0-rc1-next-20160401-00011-g1b8d87473b9e-dirty #101
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(...)
(__wake_up_common) from [<c0379624>] (__wake_up+0x38/0x4c)
(__wake_up) from [<c0a41d30>] (ak8975_irq_handler+0x28/0x30)
(ak8975_irq_handler) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389c40>] (handle_edge_irq+0xf0/0x19c)
(handle_edge_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c05ee360>] (exynos_eint_gpio_irq+0x50/0x68)
(exynos_eint_gpio_irq) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389a70>] (handle_fasteoi_irq+0xb4/0x194)
(handle_fasteoi_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c03860b4>] (__handle_domain_irq+0x5c/0xb4)
(__handle_domain_irq) from [<c0301774>] (gic_handle_irq+0x54/0x94)
(gic_handle_irq) from [<c030c910>] (__irq_usr+0x50/0x80)
The bug was reproduced on exynos4412-trats2 (with a max77693 device also
using i2c-gpio) after building max77693 as a module.
Cc: <stable@vger.kernel.org>
Fixes: 94a6d5cf7c ("iio:ak8975 Implement data ready interrupt handling")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: else should follow close brace '}'
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves a lot of merge issues with PAGE_CACHE_* changes, and an
iio driver merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will be used together with an external trigger (e.g hrtimer based
software trigger).
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When CONFIG_IIO_TRIGGER is enabled but CONFIG_IIO_BUFFER is
not, we get a build error in the st_magn driver:
drivers/iio/magnetometer/st_magn_core.c:573:23: error: 'ST_MAGN_TRIGGER_SET_STATE' undeclared here (not in a function)
.set_trigger_state = ST_MAGN_TRIGGER_SET_STATE,
^~~~~~~~~~~~~~~~~~~~~~~~~
Apparently, this ST_MAGN_TRIGGER_SET_STATE macro was meant to
be set to NULL when the definition is not available because
st_magn_buffer.c is not compiled, but the alternative definition
was not included in the original patch. This adds it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 74f5683f35 ("iio: st_magn: Add irq trigger handling")
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
GPIO handling code has been removed from the drivers (since
this is now handled by the ACPI core) in commit 0f0796509c ("iio:
remove gpio interrupt probing from drivers that use a single interrupt").
Remove the include for linux/gpio/consumer.h since it is no longer
used.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure optional regulator is properly disabled when present.
Fixes: 63d5d525cb ("iio:magnetometer:ak8975: power regulator support")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for an optional regulator which, if found into device-tree,
will power on device at probing time.
The regulator is declared into ak8975 DTS entry as a "vdd-supply" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ak_def_array bounds are not properly checked in case of ACPI matching
failure. GCC warns with the following message at line 799:
‘chipset’ may be used uninitialized in this function.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch moves hmc5843 driver from staging/iio/magnetometer
to iio/magnetometer, updates the corresponding Makefiles and
moves the hmc5843* entries to the 'Industrial I/O support ->
Magnetometer sensors' menu.
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ak_def structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CfCl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
At probe, runtime pm should be setup before registering the sysfs interface so
that all the power attributes are accurate and functional when registering.
Also, when removing the device we should unregister first to make sure
that the interfaces that may result in wakeups are no longer available.
Fix this behaviour for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553, rpr0521.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 845c877009 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Alison Schofield