-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYzznuAAoJEHm+PkMAQRiGAzMIAJDBo5otTMMLhg8eKj8Cnab4
2NyaoWDN6mtU427rzEKEfZlTtp3gIBVdFex5x442weIdw6BgRQW0dvF/uwEn08yI
9Wx7VJmIUyH9M8VmhDtkUTFrhwUGr29qb3JhENMd7tv/CiJaehGRHCT3xqo5BDdu
xiyPcwSkwP/NH24TS91G87gV6r0I0oKLSAxu+KifEFESrb8gaZaduslzpEj3m/Ds
o9EPpfzaiGAdW5EdNfPtviYbBk7ZOXwtxdMV+zlvsLcaqtYnFEsJZd2WyZL0zGML
VXBVxaYtlyTeA7Mt8YYUL+rDHELSOtCeN5zLfxUvYt+Yc0Y6LFBLDOE5h8b3eCw=
=uKUo
-----END PGP SIGNATURE-----
BackMerge tag 'v4.11-rc3' into drm-next
Linux 4.11-rc3 as requested by Daniel
Baytrail PMIC vs. PMU race fixes from Hans de Goede
This time the right version (v4), with the compile fix.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After commit 7999eecb7e ("i2c: exynos5: fix arbitration lost handling"),
some I2C transactions are failing because the TRANSFER_DONE_AUTO field is
not set in the I2C_TRANS_STATUS register so the i2c->status value is left
to -EINVAL causing the i2c->msg_complete completion to never be signaled.
For example, when reading the time of an I2C rtc on an Exynos5800 machine:
$ cat /sys/class/rtc/rtc0/time
[ 25.924594] exynos5-hsi2c 12e10000.i2c: rx timeout
[ 65.028365] max77686-rtc max77802-rtc: Fail to read time reg(-22)
cat: /sys/class/rtc/rtc0/time: Invalid argument
The Exynos5422 manual states clearly that most I2C_TRANS_STATUS reg bits
(including TRANSFER_DONE_AUTO) are cleared after the register is read. So
reading has side effects and should only be done if HSI2C_INT_I2C was set.
Fixes: 7999eecb7e ("i2c: exynos5: fix arbitration lost handling")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some platforms like hi3660 need do reset first to allow accessing registers
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ramiro Oliveira <ramiro.oliveira@synopsys.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All length fields in Linux I2C are u16, so a HW length limitation of 16
bit lengths is not a limitation. Remove the quirk structure.
Tested-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BSC data buffers to send and receive data are each of size 32 bytes
or 8 bytes 'xfersz' depending on SoC. The problem observed for all the
combined message transfer was if length of data transfer was a multiple
of 'xfersz' a repeated START was being transmitted by BSC driver. Fixed
this by appropriately setting START/STOP conditions for such transfers.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
While modifying the driver to use the STOP interrupt, the completion of the
intermediate transfers need to wake the driver back up in order to initiate
the next transfer (restart condition). Otherwise you get never ending
interrupts and only the first transfer sent.
Fixes: 71ccea095e ("i2c: riic: correctly finish transfers")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acquire P-Unit access to stop others from accessing the P-Unit while the
PMIC i2c bus is in use. This is necessary because accessing the P-Unit
from the kernel may result in the P-Unit trying to access the PMIC i2c
bus, which results in a hang when it happens while we own the PMIC i2c
bus semaphore.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=155241
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: tagorereddy <tagore.chandan@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-10-hdegoede@redhat.com
The cherrytrail punit has the pmic i2c bus access semaphore at a
different register address.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-9-hdegoede@redhat.com
Use iosf_mbi_modify instead of iosf_mbi_read + iosf_mbi_write so that
we keep the iosf_mbi_lock locked during the read-modify-write done to
reset the semaphore.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-8-hdegoede@redhat.com
On my cherrytrail tablet with axp288 pmic, just doing a bunch of repeated
reads from the pmic, e.g. "i2cdump -y 14 0x34" would lookup the tablet in
1 - 3 runs guaranteed.
This seems to be causes by the cpu trying to enter C6 or C7 while we hold
the punit bus semaphore, at which point everything just hangs.
Avoid this by disallowing the CPU to enter C6 or C7 before acquiring the
punit bus semaphore.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-7-hdegoede@redhat.com
If (!shared_host) simply return 0, this avoids delaying the probe if
iosf_mbi_available() returns false when an i2c bus is not using the
punit semaphore.
Also move the if (!iosf_mbi_available()) check to above the
dev_info, so that we do not repeat the dev_info on every probe
until iosf_mbi_available() returns true.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-6-hdegoede@redhat.com
Pass dw_i2c_dev into the helper functions, this is a preparation patch
for the punit semaphore fixes done in the other patches in this set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-5-hdegoede@redhat.com
Rename accessor_flags to flags, so that we can use the field for
other flags too. This is a preparation patch for adding cherrytrail
support to the punit semaphore code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-4-hdegoede@redhat.com
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull i2c updates from Wolfram Sang:
"I2C has for you two new drivers (Tegra BPMP and STM32F4), interrupt
support for pca954x muxes, and a bunch of driver bugfixes and
improvements. Nothing really special this cycle.
A few commits have been added to my tree just recently. Those are the
Tegra BPMP driver and a few straightforward bugfixes or cleanups which
I prefer to have upstream rather soonish. The rest had proper
linux-next exposure"
* 'i2c/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (25 commits)
i2c: thunderx: Replace pci_enable_msix()
i2c: exynos5: fix arbitration lost handling
i2c: exynos5: disable fifo-almost-empty irq signal when necessary
i2c: at91: ensure state is restored after suspending
i2c: bcm2835: Avoid possible NULL ptr dereference
i2c: Add Tegra BPMP I2C proxy driver
dt-bindings: Add Tegra186 BPMP I2C binding
misc: eeprom: at24: use device_property_*() functions instead of of_get_property()
i2c: mux: pca954x: Add interrupt controller support
dt: bindings: i2c-mux-pca954x: Add documentation for interrupt controller
i2c: mux: pca954x: Add missing pca9542 definition to chip_desc
i2c: riic: correctly finish transfers
i2c: i801: Add support for Intel Gemini Lake
i2c: mux: pca9541: Export OF device ID table as module aliases
i2c: mux: pca954x: Export OF device ID table as module aliases
i2c: mux: mlxcpld: remove unused including <linux/version.h>
i2c: busses: constify i2c_algorithm structures
i2c: i2c-mux-gpio: rename i2c-gpio-mux to i2c-mux-gpio
i2c: sh_mobile: document support for r8a7796 (R-Car M3-W)
i2c: i2c-cros-ec-tunnel: Reduce logging noise
...
Using pci_alloc_irq_vectors() instead of the deprecated
pci_enable_msix() allows to remove the msix_entry from
struct octeon_i2c and thus to get rid of the config symbol check.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of arbitration lost adequate interrupt sometimes is not signaled.
As a result transfer timeouts and is not retried, as it should. To avoid
such cases code is added to check transaction status in case of every
interrupt.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fifo-almost-empty irq signal should be disabled as soon as possible,
to avoid unnecessary interrupt storm. The best moment is when there is
no more data to feed fifo.
This patch fixes system stalls caused by IRQ storm.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When going to suspend, the I2C registers may be lost because the power to
VDDcore is cut. Restore them when resuming.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit e247454103 ("bcm2835: Fix hang for writing messages
larger than 16 bytes") the interrupt handler is prone to a possible
NULL pointer dereference. This could happen if an interrupt fires
before curr_msg is set by bcm2835_i2c_xfer_msg() and randomly occurs
on the RPi 3. Even this is an unexpected behavior the driver must
handle that with an error instead of a crash.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: e247454103 ("bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Tegra BPMP I2C driver. The BPMP is the boot and power management
processor embedded in Tegra SoCs. In newer SoC versions, access to one
of the I2C busses goes via the BPMP, requiring a different "proxy" I2C
driver that accesses the bus via the real I2C driver embedded in the
BPMP firmware.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.
At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.
Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.
This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.
Fixes: 310c18a414 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Gemini Lake has the same SMBus host controller than Intel Broxton.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBSLVCNT must be protected with the piix4_mutex_sb800 in order to avoid
multiple buses accessing to the semaphore at the same time.
Fixes: 701dc207bf ("i2c: piix4: Avoid race conditions with IMC")
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since '701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")' we
are using the SMBSLVCNT register at offset 0x8. We need to request it.
Fixes: 701dc207bf ("i2c: piix4: Avoid race conditions with IMC")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declare i2c_algorithm structures as const as they are only stored in the
algo field of an i2c_adapter structure. This field is of type const, so
i2c_algorithm structures having this property can be made const too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> for
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If an i2c access through i2c-cros-ec-tunnel returns an error, the following
log message is seen on the console.
cros-ec-i2c-tunnel ff200000.spi:ec@0:i2c-tunnel:
Error parsing EC i2c message -121
This can happen a lot if, for example, the i2c-detect command is executed.
Since it is perfectly normal for an i2c controller to report an error,
drop the message. Also, report -ENXIO instead of -EREMOTEIO if the access
error is due to NAK from the device, and return -EIO instead of -EREMOTEIO
for other errors, as suggested in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When system enters VLLS mode, module power is turned off. As a result,
all registers are reset to HW default value. After exiting VLLS mode,
registers are still in default mode. As a result, the pinctrl settings
are incorrect, which will affect the module function.
The patch recovers the pinctrl setting when exit VLLS mode.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
[wsa: added missing include]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit implements suspend/resume support in the mv64xxx I2C
controller driver. There is no need to implement a ->suspend() hook, as
calling mv64xxx_i2c_hw_init() at ->resume() time is enough.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Lior Amsalem <alior@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
[Thomas: switch to dev_pm_ops, fix build warning when !PM.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the STM32F4 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The cadence I2C driver calls cdns_i2c_writereg(..) to setup a workaround
in the controller, but did so after calling i2c_add_adapter() which starts
probing devices on the bus. Change the order so that the configuration is
completely finished before using the adapter.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On AMD's SB800 and upwards, the SMBus is shared with the Integrated
Micro Controller (IMC).
The platform provides a hardware semaphore to avoid race conditions
among them. (Check page 288 of the SB800-Series Southbridges Register
Reference Guide http://support.amd.com/TechDocs/45482.pdf)
Without this patch, many access to the SMBus end with an invalid
transaction or even with the bus stalled.
Reported-by: Alexandre Desnoyers <alex@qtec.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>:
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI always sets Tx/Rx FIFO to 32. This configuration will
cause problem if the IP core supports a FIFO size of less than 32.
The driver should read the FIFO size from the IP and select the smaller
one of the two.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In DTB case, i2c-core doesn't create slave device which is installed
on i2c-xgene bus because of missing code in this driver.
This patch fixes this issue.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.
Return -EIO in case of a failed data read. For all other
cases just return so subsequent operations will fail
and trigger the recovery.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- the first series of making i2c_device_id optional instead of
mandatory (in favor of alternatives like of_device_id).
This involves adding a new probe callback (probe_new) which removes
some peculiarities I2C had for a long time now. The new probe is
matching the other subsystems now and the old one will be removed
once all users are converted. It is expected to take a while but
there is ongoing interest in that.
- SMBus Host Notify introduced 4.9 got refactored. They are now using
interrupts instead of the alert callback which solves multiple
issues.
- new drivers for iMX LowPower I2C, Mellanox CPLD and its I2C mux
- significant refactoring for bcm2835 driver
- the usual set of driver updates and improvements
* 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (46 commits)
i2c: fsl-lpi2c: read lpi2c fifo size in probe()
i2c: octeon: thunderx: Remove double-check after interrupt
i2c: octeon: thunderx: TWSI software reset in recovery
i2c: cadence: Allow Cadence I2C to be selected for Cadence Xtensa CPUs
i2c: sh_mobile: Add per-Generation fallback bindings
i2c: rcar: Add per-Generation fallback bindings
i2c: imx-lpi2c: add low power i2c bus driver
dt-bindings: i2c: imx-lpi2c: add devicetree bindings
i2c: designware-pcidrv: Add 10bit address feature to medfield/merrifield
i2c: pxa: Add support for the I2C units found in Armada 3700
i2c: pxa: Add definition of fast and high speed modes via the regs layout
dt-bindings: i2c: pxa: Update the documentation for the Armada 3700
i2c: qup: support SMBus block read
i2c: qup: add ACPI support
i2c: designware: Consolidate default functionality bits
i2c: i2c-mux-gpio: update mux with gpiod_set_array_value_cansleep
i2c: mux: pca954x: Add ACPI support for pca954x
i2c: use an IRQ to report Host Notify events, not alert
i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0
i2c: i801: use the BIT() macro for FEATURES_* also
...
The lpi2c fifo size is a read only parameter resides Parameter
Register. It's better to read lpi2c tx/rx fifo size in probe()
other than just define a macro for it.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 1bb1ff3e7c ("i2c: octeon: Improve performance if interrupt is
early") added a double-check around the wait_event_timeout() condition.
The performance problem that this commit tried to work-around
could not be reproduced. It also makes the wait condition more
complicated then it should be. Therefore remove the double-check.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I've seen i2c recovery reporting long loops of:
[ 1035.887818] i2c i2c-4: SCL is stuck low, exit recovery
[ 1037.999748] i2c i2c-4: SCL is stuck low, exit recovery
[ 1040.111694] i2c i2c-4: SCL is stuck low, exit recovery
...
Add a TWSI software reset which clears the status and
STA,STP,IFLG in SW_TWSI_EOP_TWSI_CTL.
With this the recovery works fine and above message is not seen.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch allows Cadence I2C controller to be selected in systems using Cadence Xtensa processors.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add per-Generation fallback bindings for R-Car SoCs.
This is in keeping with the compatibility string scheme is being adopted
for drivers for Renesas SoCs.
Also, improve readability by listing the rmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that it's not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Also:
* Deprecate renesas,i2c-rcar. It seems poorly named as it is only
compatible with R-Car Gen 1. It also appears unused in mainline.
* Add some text to describe per-SoC bindings
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds lpi2c bus driver to support new i.MX products
which use lpi2c instead of the old imx i2c.
The lpi2c can continue operating in stop mode when an appropriate
clock is available. It is also designed for low CPU overhead with
DMA offloading of FIFO register accesses.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Both Merrifield TRM and Medfield TRM state:
"Both 7-bit and 10-bit addressing modes are supported."
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Armada 3700 has two I2C controllers that is compliant with the I2C
Bus Specificiation 2.1, supports multi-master and different bus speed:
Standard mode (up to 100 KHz), Fast mode (up to 400 KHz),
High speed mode (up to 3.4 Mhz).
This IP block has a lot of similarity with the PXA, except some register
offsets and bitfield. This commits adds a basic support for this I2C
unit.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Dave Airlie