I think we need to let the dirty node pages remain in the page cache instead
of rewriting them in their places.
So, after done with successful recovery, write_checkpoint will flush all of them
through the normal write path.
Through this, we can avoid potential error cases in terms of block allocation.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Fix typo and some grammatical errors.
The words "filesystem" and "readahead" are being used without the space treewide.
Signed-off-by: Park Ju Hyung <qkrwngud825@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch uses for_each_set_bit to simplify some codes in f2fs.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There are redundant lines in allocate_data_block.
In this function, we call refresh_sit_entry with old seg and old curseg.
After that, we call locate_dirty_segment with old curseg.
But, the new address is always allocated from old curseg and
we call locate_dirty_segment with old curseg in refresh_sit_entry.
So, we do not need to call locate_dirty_segment with old curseg again.
We've discussed like below:
Jaegeuk said:
"When considering SSR, we need to take care of the following scenario.
- old segno : X
- new address : Z
- old curseg : Y
This means, a new block is supposed to be written to Z from X.
And Z is newly allocated in the same path from Y.
In that case, we should trigger locate_dirty_segment for Y, since
it was a current_segment and can be dirty owing to SSR.
But that was not included in the dirty list."
Changman said:
"We already choosed old curseg(Y) and then we allocate new address(Z) from old
curseg(Y). After that we call refresh_sit_entry(old address, new address).
In the funcation, we call locate_dirty_segment with old seg and old curseg.
So calling locate_dirty_segment after refresh_sit_entry again is redundant."
Jaegeuk said:
"Right. The new address is always allocated from old_curseg."
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Dongho Sim <dh.sim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds a mount option, nobarrier, in f2fs.
The assumption in here is that file system keeps the IO ordering, but
doesn't care about cache flushes inside the storages.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In this patch we use below inner macro and function to clean up codes.
1. ADDRS_PER_PAGE
2. SM_I
3. f2fs_readonly
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75861
Denis 2014-05-10 11:28:59 UTC reported:
"F2FS-fs (mmcblk0p28): mounting..
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
[<c0a2f678>] (_raw_spin_lock+0x3c/0x70) from [<c03a0330>] (issue_flush_thread+0x50/0x17c)
[<c03a0330>] (issue_flush_thread+0x50/0x17c) from [<c01b4064>] (kthread+0x98/0xa4)
[<c01b4064>] (kthread+0x98/0xa4) from [<c0108060>] (kernel_thread_exit+0x0/0x8)"
This patch assign cmd_control_info in sm_info before issue_flush_thread is being
created, so this make sure that issue flush thread will have no chance to access
invalid info in fcc.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If we use slab memory in f2fs_issue_flush(), we will face memory pressure and
latency time caused by racing of kmem_cache_{alloc,free}.
Let's alloc memory in stack instead of slab.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce help function {create,destroy}_flush_cmd_control to clean up
the create/destory flush merge operation.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Split the flush_merge fields from sm_i, and use the new struct flush_cmd_control
to wrap it, so that we can igonre these fileds if flush_merge is disable, and
it alse can the structs more neat.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add the *remount* handle of flush_merge option, so that the users
can enable flush_merge in the runtime, such as the underlying device
handles the cache_flush command relatively slowly.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The f2fs always scans the next chain of direct node blocks.
But some garbage blocks are able to be remained due to no discard support or
SSR triggers.
This occasionally wreaks recovering wrong inodes that were used or BUG_ONs
due to reallocating node ids as follows.
When mount this f2fs image:
http://linuxtesting.org/downloads/f2fs_fault_image.zip
BUG_ON is triggered in f2fs driver (messages below are generated on
kernel 3.13.2; for other kernels output is similar):
kernel BUG at fs/f2fs/node.c:215!
Call Trace:
[<ffffffffa032ebad>] recover_inode_page+0x1fd/0x3e0 [f2fs]
[<ffffffff811446e7>] ? __lock_page+0x67/0x70
[<ffffffff81089990>] ? autoremove_wake_function+0x50/0x50
[<ffffffffa0337788>] recover_fsync_data+0x1398/0x15d0 [f2fs]
[<ffffffff812b9e5c>] ? selinux_d_instantiate+0x1c/0x20
[<ffffffff811cb20b>] ? d_instantiate+0x5b/0x80
[<ffffffffa0321044>] f2fs_fill_super+0xb04/0xbf0 [f2fs]
[<ffffffff811b861e>] ? mount_bdev+0x7e/0x210
[<ffffffff811b8769>] mount_bdev+0x1c9/0x210
[<ffffffffa0320540>] ? validate_superblock+0x210/0x210 [f2fs]
[<ffffffffa031cf8d>] f2fs_mount+0x1d/0x30 [f2fs]
[<ffffffff811b9497>] mount_fs+0x47/0x1c0
[<ffffffff81166e00>] ? __alloc_percpu+0x10/0x20
[<ffffffff811d4032>] vfs_kern_mount+0x72/0x110
[<ffffffff811d6763>] do_mount+0x493/0x910
[<ffffffff811615cb>] ? strndup_user+0x5b/0x80
[<ffffffff811d6c70>] SyS_mount+0x90/0xe0
[<ffffffff8166f8d9>] system_call_fastpath+0x16/0x1b
Found by Linux File System Verification project (linuxtesting.org).
Reported-by: Andrey Tsyvarev <tsyvarev@ispras.ru>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Enable flush_merge only in f2fs is not read-only, so does the mount
option show.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Some storage devices show relatively high latencies to complete cache_flush
commands, even though their normal IO speed is prettry much high. In such
the case, it needs to merge cache_flush commands as much as possible to avoid
issuing them redundantly.
So, this patch introduces a mount option, "-o flush_merge", to mitigate such
the overhead.
If this option is enabled by user, F2FS merges the cache_flush commands and then
issues just one cache_flush on behalf of them. Once the single command is
finished, F2FS sends a completion signal to all the pending threads.
Note that, this option can be used under a workload consisting of very intensive
concurrent fsync calls, while the storage handles cache_flush commands slowly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In the f2fs_wait_on_page_writeback, io->bio should be covered by io_rwsem.
Otherwise, the bio pointer can become a dangling pointer due to data races.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch use list_for_each_entry{_safe} instead of list_for_each{_safe} for
simplfying code.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch introduce is_merged_page() to check whether current page is merged
in f2fs bio cache. When page is not in cache, we can avoid submitting bio cache,
resulting in having more chance to merge pages.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
It is more reasonable to determine the reclaiming rate of prefree segments
according to the volume size, which is set to 5% by default.
For example, if the volume is 128GB, the prefree segments are reclaimed
when the number reaches to 6.4GB.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We should return error number of read_normal_summaries instead of -EINVAL when
read_normal_summaries failed.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, we ra_sum_pages to pre-read contiguous pages as more
as possible, and if we fail to alloc more pages, an ENOMEM error
will be reported upstream, even though we have alloced some pages
yet. In fact, we can use the available pages to do the job partly,
and continue the rest in the following circle. Only reporting ENOMEM
upstream if we really can not alloc any available page.
And another fix is ignoring dealing with the following pages if an
EIO occurs when reading page from page_list.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: modify the flow for better neat code]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch help us to cleanup the readahead code by merging ra_{sit,nat}_pages
function into ra_meta_pages.
Additionally the new function is used to readahead cp block in
recover_orphan_inodes.
Change log from v1:
o fix a deadloop bug pointed by Jaegeuk Kim.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce help function META_MAPPING() to get the cache meta blocks'
address space.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Fixed a variety of trivial checkpatch warnings. The only delta should
be some minor formatting on log strings that were split / too long.
Signed-off-by: Chris Fries <cfries@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
"boo sync" parameter is never referenced in f2fs_wait_on_page_writeback.
We should remove this parameter.
Signed-off-by: Yuan Zhong <yuan.mark.zhong@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When considering a bunch of data writes with very frequent fsync calls, we
are able to think the following performance regression.
N: Node IO, D: Data IO, IO scheduler: cfq
Issue pending IOs
D1 D2 D3 D4
D1 D2 D3 D4 N1
D2 D3 D4 N1 N2
N1 D3 D4 N2 D1
--> N1 can be selected by cfq becase of the same priority of N and D.
Then D3 and D4 would be delayed, resuling in performance degradation.
So, when processing the fsync call, it'd better give higher priority to data IOs
than node IOs by assigning WRITE and WRITE_SYNC respectively.
This patch improves the random wirte performance with frequent fsync calls by up
to 10%.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When using the f2fs_io_info in the low level, we still need to merge the
rw and rw_flag, so use the rw to hold all the io flags directly,
and remove the rw_flag field.
ps.It is based on the previous patch:
f2fs: move all the bio initialization into __bio_alloc
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs doesn't support direct IOs with high performance, which throws
every write requests via the buffered write path, resulting in highly
performance degradation due to memory opeations like copy_from_user.
This patch introduces a new direct IO path in which every write requests are
processed by generic blockdev_direct_IO() with enhanced get_block function.
The get_data_block() in f2fs handles:
1. if original data blocks are allocates, then give them to blockdev.
2. otherwise,
a. preallocate requested block addresses
b. do not use extent cache for better performance
c. give the block addresses to blockdev
This policy induces that:
- new allocated data are sequentially written to the disk
- updated data are randomly written to the disk.
- f2fs gives consistency on its file meta, not file data.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch introduces new sysfs entries for users to control the policy of
in-place-updates, namely IPU, in f2fs.
Sometimes f2fs suffers from performance degradation due to its out-of-place
update policy that produces many additional node block writes.
If the storage performance is very dependant on the amount of data writes
instead of IO patterns, we'd better drop this out-of-place update policy.
This patch suggests 5 polcies and their triggering conditions as follows.
[sysfs entry name = ipu_policy]
0: F2FS_IPU_FORCE all the time,
1: F2FS_IPU_SSR if SSR mode is activated,
2: F2FS_IPU_UTIL if FS utilization is over threashold,
3: F2FS_IPU_SSR_UTIL if SSR mode is activated and FS utilization is over
threashold,
4: F2FS_IPU_DISABLE disable IPU. (=default option)
[sysfs entry name = min_ipu_util]
This parameter controls the threshold to trigger in-place-updates.
The number indicates percentage of the filesystem utilization, and used by
F2FS_IPU_UTIL and F2FS_IPU_SSR_UTIL policies.
For more details, see need_inplace_update() in segment.h.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch introduces f2fs_io_info to mitigate the complex parameter list.
struct f2fs_io_info {
enum page_type type; /* contains DATA/NODE/META/META_FLUSH */
int rw; /* contains R/RS/W/WS */
int rw_flag; /* contains REQ_META/REQ_PRIO */
}
1. f2fs_write_data_pages
- DATA
- WRITE_SYNC is set when wbc->WB_SYNC_ALL.
2. sync_node_pages
- NODE
- WRITE_SYNC all the time
3. sync_meta_pages
- META
- WRITE_SYNC all the time
- REQ_META | REQ_PRIO all the time
** f2fs_submit_merged_bio() handles META_FLUSH.
4. ra_nat_pages, ra_sit_pages, ra_sum_pages
- META
- READ_SYNC
Cc: Fan Li <fanofcode.li@samsung.com>
Cc: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously f2fs submits most of write requests using WRITE_SYNC, but f2fs_write_data_pages
submits last write requests by sync_mode flags callers pass.
This causes a performance problem since continuous pages with different sync flags
can't be merged in cfq IO scheduler(thanks yu chao for pointing it out), and synchronous
requests often take more time.
This patch makes the following modifies to DATA writebacks:
1. every page will be written back using the sync mode caller pass.
2. only pages with the same sync mode can be merged in one bio request.
These changes are restricted to DATA pages.Other types of writebacks are modified
To remain synchronous.
In my test with tiotest, f2fs sequence write performance is improved by about 7%-10% ,
and this patch has no obvious impact on other performance tests.
Signed-off-by: Fan Li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch integrates redundant bio operations on read and write IOs.
1. Move bio-related codes to the top of data.c.
2. Replace f2fs_submit_bio with f2fs_submit_merged_bio, which handles read
bios additionally.
3. Introduce __submit_merged_bio to submit the merged bio.
4. Change f2fs_readpage to f2fs_submit_page_bio.
5. Introduce f2fs_submit_page_mbio to integrate previous submit_read_page and
submit_write_page.
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com >
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously f2fs allocates its own bi_private data structure all the time even
though we don't use it. But, can we remove this bi_private allocation?
This patch removes such the additional bi_private allocation.
1. Retrieve f2fs_sb_info from its page->mapping->host->i_sb.
- This removes the usecases of bi_private in end_io.
2. Use bi_private only when we really need it.
- The bi_private is used only when the checkpoint procedure is conducted.
- When conducting the checkpoint, f2fs submits a META_FLUSH bio to wait its bio
completion.
- Since we have no dependancies to remove bi_private now, let's just use
bi_private pointer as the completion pointer.
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes some bit overflows by the shift operations.
Dan Carpenter reported potential bugs on bit overflows as follows.
fs/f2fs/segment.c:910 submit_write_page()
warn: should 'blk_addr << ((sbi)->log_blocksize - 9)' be a 64 bit type?
fs/f2fs/checkpoint.c:429 get_valid_checkpoint()
warn: should '1 << ()' be a 64 bit type?
fs/f2fs/data.c:408 f2fs_readpage()
warn: should 'blk_addr << ((sbi)->log_blocksize - 9)' be a 64 bit type?
fs/f2fs/data.c:457 submit_read_page()
warn: should 'blk_addr << ((sbi)->log_blocksize - 9)' be a 64 bit type?
fs/f2fs/data.c:525 get_data_block_ro()
warn: should 'i << blkbits' be a 64 bit type?
Bug-Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Let's send REQ_META or REQ_PRIO when reading meta area such as NAT/SIT
etc.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch inserts information of bio types in more detail.
So, we can now see REQ_META and REQ_PRIO too.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously we read sit entries page one by one, this method lost the chance
of reading contiguous page together. So we read pages as contiguous as
possible for better mount performance.
change log:
o merge judgements/use 'Continue' or 'Break' instead of 'Goto' as Gu Zheng
suggested.
o add mark_page_accessed() before release page to delay VM reclaiming.
o remove '*order' for simplification of function as Jaegeuk Kim suggested.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: fix a bug on the block address calculation]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for f2fs_submit_read_bio.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: integrate tracepoints of f2fs_submit_read(_write)_bio]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for submit_read_page.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: integrate tracepoints of f2fs_submit_read(_write)_page]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The f2fs has three bio types, NODE, DATA, and META, and manages some data
structures per each bio types.
The codes are a little bit messy, thus, this patch introduces a bio array
which groups individual data structures as follows.
struct f2fs_bio_info {
struct bio *bio; /* bios to merge */
sector_t last_block_in_bio; /* last block number */
struct mutex io_mutex; /* mutex for bio */
};
struct f2fs_sb_info {
...
struct f2fs_bio_info write_io[NR_PAGE_TYPE]; /* for write bios */
...
};
The code changes from this new data structure are trivial.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes an unnecessary semaphore (i.e., sbi->bio_sem).
There is no reason to use the semaphore when f2fs submits read and write IOs.
Instead, let's use a write mutex and cover the sbi->bio[] by the lock.
Change log from v1:
o split write_mutex suggested by Chao Yu
Chao described,
"All DATA/NODE/META bio buffers in superblock is protected by
'sbi->write_mutex', but each bio buffer area is independent, So we
should split write_mutex to three for DATA/NODE/META."
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Change log from v1:
o fix 32bit drops reported by Dan Carpenter
This patch adds f2fs_issue_discard() to clean up blkdev_issue_discard() flows.
Dan carpenter reported:
"block_t is a 32 bit type and sector_t is a 64 bit type. The upper 32
bits of the sector_t are not used because the shift will wrap."
Bug-Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds key functions to activate the small discard feature.
Note that this procedure is conducted during the checkpoint only.
In flush_sit_entries(), when a new dirty sit entry is flushed, f2fs calls
add_discard_addrs() which searches candidates to be discarded.
The candidates should be marked *invalidated* and also previous checkpoint
recognizes it as *valid*.
At the end of a checkpoint procedure, f2fs throws discards based on the
discard entry list.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a slab cache entry for small discards.
Each entry consists of:
struct discard_entry {
struct list_head list; /* list head */
block_t blkaddr; /* block address to be discarded */
int len; /* # of consecutive blocks of the discard */
};
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
To find a zero bit using the result of OR operation between ckpt_valid_map
and cur_valid_map is more fast than find a zero bit in each bitmap.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
[Jaegeuk Kim: adjust changed function name]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When f2fs_set_bit is used, in a byte MSB and LSB is reversed,
in that case we can use __find_rev_next_bit or __find_rev_next_zero_bit.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
[Jaegeuk Kim: change the function names]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
o Changes from v1
Use find_next(_zero)_bit suggested by jg.kim
When f2fs issues discard command, if segment is contiguous,
let's issue more large segment to gather adjacent segments.
** blktrace **
179,1 0 5859 42.619023770 971 C D 131072 + 2097152 [0]
179,1 0 33665 108.840475468 971 C D 2228224 + 2494464 [0]
179,1 0 33671 109.131616427 971 C D 14909440 + 344064 [0]
179,1 0 33677 109.137100677 971 C D 15261696 + 4096 [0]
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
use genernal method supported by kernel
o changes from v1
If any waiter exists at end io, wake up it.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
A NULL point should avoid to be used in destroy_segment_manager after allocating
memory fail for f2fs_sm_info.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
npages_for_summary_flush uses (SUMMARY_SIZE + 1) as the size of a f2fs_summary
while its actual size is SUMMARY_SIZE. So the result sometimes is bigger than
actual number by one, which causes checkpoint can't be written into disk
contiguously, and sometimes summary blocks can't be compacted like they should.
Besides, when writing summary blocks into pages, if remain space in a page
isn't big enough for one f2fs_summary, it will be left unused, current code
seems not to take it into account.
Signed-off-by: Fan Li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If you want to remove unnecessary BUG_ONs, you can just turn off F2FS_CHECK_FS
in your kernel config.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Only one dirty type is set in __locate_dirty_segment and we can know
dirty type of segment. So we don't need to check other dirty types.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, set_page_dirty is called every time after writting one summary info
into compacted summary page,
To avoid redundant set_page_dirty, we only call set_page_dirty before release
page.
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch merges some background jobs into this new function.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs postpones reclaiming prefree segments into free segments
as much as possible.
However, if user writes and deletes a bunch of data without any sync or fsync
calls, some flash storages can suffer from garbage collections.
So, this patch adds the reclaiming codes to f2fs_write_node_pages and background
GC thread.
If there are a lot of prefree segments, let's do checkpoint so that f2fs
submits discard commands for the prefree regions to the flash storage.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Because one dirty seg can only be mapped to one dirty_type. Otherwise, it's a bug.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: modify a comment related to this patch]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, do_checkpoint() will call congestion_wait() for waiting the pages
(previous submitted node/meta/data pages) to be written back.
Because congestion_wait() will set a regular period (e.g. HZ / 50 ) for waiting, and
no additional wake up mechanism was introduced if IO ends up before regular period costed.
Yuan Zhong found there is a situation that after the pages have been written back,
but the checkpoint thread still wait for congestion_wait to exit.
So here we store checkpoint task into f2fs_sb when doing checkpoint, it'll wait for IO completes
if there's IO going on, and in the end IO path, wake up checkpoint task when IO ends up.
Thanks to Yuan Zhong's pre work about this problem.
Reported-by: Yuan Zhong <yuan.mark.zhong@samsung.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch add macro MAX_BIO_BLOCKS to limit value of npages in
f2fs_bio_alloc, it can avoid allocating failure in bio_alloc caused by
npages is larger than BIO_MAX_PAGES.
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
An error "label at end of compound statement" will occur if CONFIG_F2FS_STAT_FS
disabled.
fs/f2fs/segment.c:556:1: error: label at end of compound statement
So clean up the 'out' label to fix it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes a deadlock bug that occurs quite often when there are
concurrent write and fsync on a same file.
Following is the simplified call trace when tasks get hung.
fsync thread:
- f2fs_sync_file
...
- f2fs_write_data_pages
...
- update_extent_cache
...
- update_inode
- wait_on_page_writeback
bdi writeback thread
- __writeback_single_inode
- f2fs_write_data_pages
- mutex_lock(sbi->writepages)
The deadlock happens when the fsync thread waits on a inode page that has
been added to the f2fs' cached bio sbi->bio[NODE], and unfortunately,
no one else could be able to submit the cached bio to block layer for
writeback. This is because the fsync thread already hold a sbi->fs_lock and
the sbi->writepages lock, causing the bdi thread being blocked when attempt
to write data pages for the same inode. At the same time, f2fs_gc thread
does not notice the situation and could not help. Even the sync syscall
gets blocked.
To fix it, we could submit the cached bio first before waiting on a inode page
that is being written back.
Signed-off-by: Jin Xu <jinuxstyle@gmail.com>
[Jaegeuk Kim: add more cases to use f2fs_wait_on_page_writeback]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
bio->bi_private is not always needed. As in the reading data path,
end_read_io does not need bio_private for further using, so moving
bio_private allocation out of f2fs_bio_alloc(). Alloc it in the
submit_write_page(), and ignore it in the f2fs_readpage().
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes check_prefree_segments initially designed to enhance the
performance by narrowing the range of LBA usage across the whole block device.
When allocating a new segment, previous f2fs tries to find proper prefree
segments, and then, if finds a segment, it reuses the segment for further
data or node block allocation.
However, I found that this was totally wrong approach since the prefree segments
have several data or node blocks that will be used by the roll-forward mechanism
operated after sudden-power-off.
Let's assume the following scenario.
/* write 8MB with fsync */
for (i = 0; i < 2048; i++) {
offset = i * 4096;
write(fd, offset, 4KB);
fsync(fd);
}
In this case, naive segment allocation sequence will be like:
data segment: x, x+1, x+2, x+3
node segment: y, y+1, y+2, y+3.
But, if we can reuse prefree segments, the sequence can be like:
data segment: x, x+1, y, y+1
node segment: y, y+1, y+2, y+3.
Because, y, y+1, and y+2 became prefree segments one by one, and those are
reused by data allocation.
After conducting this workload, we should consider how to recover the latest
inode with its data.
If we reuse the prefree segments such as y or y+1, we lost the old node blocks
so that f2fs even cannot start roll-forward recovery.
Therefore, I suggest that we should remove reusing prefree segments.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Optimize the while loop condition
Since this condition will always be true and while loop will
be terminated by the following condition in code:
if (segno >= TOTAL_SEGS(sbi))
break;
Hence we can replace the while loop condition with while(1)
instead of always checking for segno to be less than Total segs.
Also we do not need to use TOTAL_SEGS() everytime. We can store
this value in a local variable since this value is constant.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If a file is linked, f2fs loose its parent inode number so that fsync calls
for the linked file should do checkpoint all the time.
But, if we can recover its parent inode number after the checkpoint, we can
adjust roll-forward mechanism for the further fsync calls, which is able to
improve the fsync performance significatly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
It's used only locally and could be static.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We can get the value directly from pointer "curseg".
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Some, counters are needed only for the statistical information
while debugging.
So, those can be controlled using CONFIG_F2FS_STAT_FS,
pushing the usage for few variables under this flag.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When testing f2fs on an SSD, I found some 128 page IOs followed by 1 page IO
were issued by f2fs_write_node_pages.
This means that there were some mishandling flows which degrades performance.
Previous f2fs_write_node_pages determines the number of pages to be written,
nr_to_write, as follows.
1. The bio_get_nr_vecs returns 129 pages.
2. The bio_alloc makes a room for 128 pages.
3. The initial 128 pages go into one bio.
4. The existing bio is submitted, and a new bio is prepared for the last 1 page.
5. Finally, sync_node_pages submits the last 1 page bio.
The problem is from the use of bio_get_nr_vecs, so this patch replace it
with max_hw_blocks using queue_max_sectors.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Adding REQ_META for all the metadata requests can help in improving the
FS performance, if the underlying device supports TAGGING.
So, when considering the submit_bio path for all the f2fs requests. We can
add REQ_META for all the META requests.
As a precursor to this change we considered the commit
4265900e0b 'mmc: MMC-4.5 Data Tag Support'
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add tracepoints to debug the various page write operation
like data pages, meta pages.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
[Jaegeuk: remove unnecessary tracepoints]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Like below, there are 8 segment bitmaps for SSR victim candidates.
enum dirty_type {
DIRTY_HOT_DATA, /* dirty segments assigned as hot data logs */
DIRTY_WARM_DATA, /* dirty segments assigned as warm data logs */
DIRTY_COLD_DATA, /* dirty segments assigned as cold data logs */
DIRTY_HOT_NODE, /* dirty segments assigned as hot node logs */
DIRTY_WARM_NODE, /* dirty segments assigned as warm node logs */
DIRTY_COLD_NODE, /* dirty segments assigned as cold node logs */
DIRTY, /* to count # of dirty segments */
PRE, /* to count # of entirely obsolete segments */
NR_DIRTY_TYPE
};
The upper 6 bitmaps indicates segments dirtied by active log areas respectively.
And, the DIRTY bitmap integrates all the 6 bitmaps.
For example,
o DIRTY_HOT_DATA : 1010000
o DIRTY_WARM_DATA: 0100000
o DIRTY_COLD_DATA: 0001000
o DIRTY_HOT_NODE : 0000010
o DIRTY_WARM_NODE: 0000001
o DIRTY_COLD_NODE: 0000000
In this case,
o DIRTY : 1111011,
which means that we should guarantee the consistency between DIRTY and other
bitmaps concreately.
However, the SSR mode selects victims freely from any log types, which can set
multiple bits across the various bitmap types.
So, this patch eliminates this inconsistency.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a new condition that allocates free segments in the current
active section even if SSR is needed.
Otherwise, f2fs cannot allocate remained free segments in the section since
SSR finds dirty segments only.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes a bitmap for victim segments selected by foreground GC, and
modifies the other bitmap for victim segments selected by background GC.
1) foreground GC bitmap
: We don't need to manage this, since we just only one previous victim section
number instead of the whole victim history.
The f2fs uses the victim section number in order not to allocate currently
GC'ed section to current active logs.
2) background GC bitmap
: This bitmap is used to avoid selecting victims repeatedly by background GCs.
In addition, the victims are able to be selected by foreground GCs, since
there is no need to read victim blocks during foreground GCs.
By the fact that the foreground GC reclaims segments in a section unit, it'd
be better to manage this bitmap based on the section granularity.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When allocating a new segment under the LFS mode, we should keep the section
boundary.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Let's use a macro to get the total number of sections.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Use kmemdup instead of kzalloc and memcpy.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Acked-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch makes clearer the ambiguous f2fs_gc flow as follows.
1. Remove intermediate checkpoint condition during f2fs_gc
(i.e., should_do_checkpoint() and GC_BLOCKED)
2. Remove unnecessary return values of f2fs_gc because of #1.
(i.e., GC_NODE, GC_OK, etc)
3. Simplify write_checkpoint() because of #2.
4. Clarify the main f2fs_gc flow.
o monitor how many freed sections during one iteration of do_garbage_collect().
o do GC more without checkpoints if we can't get enough free sections.
o do checkpoint once we've got enough free sections through forground GCs.
5. Adopt thread-logging (Slack-Space-Recycle) scheme more aggressively on data
log types. See. get_ssr_segement()
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch enhances the checkpoint routine to cope with IO errors.
Basically f2fs detects IO errors from end_io_write, and the errors are able to
be occurred during one of data, node, and meta page writes.
In the previous code, when an IO error is occurred during writes, f2fs sets a
flag, CP_ERROR_FLAG, in the raw ckeckpoint buffer which will be written to disk.
Afterwards, write_checkpoint() will check the flag and remount f2fs as a
read-only (ro) mode.
However, even once f2fs is remounted as a ro mode, dirty checkpoint pages are
freely able to be written to disk by flusher or kswapd in background.
In such a case, after cold reboot, f2fs would restore the checkpoint data having
CP_ERROR_FLAG, resulting in disabling write_checkpoint and remounting f2fs as
a ro mode again.
Therefore, let's prevent any checkpoint page (meta) writes once an IO error is
occurred, and remount f2fs as a ro mode right away at that moment.
Reported-by: Oliver Winker <oliver@oli1170.net>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
I'd like to revisit the f2fs_gc flow and rewrite as follows.
1. In practical, the nGC parameter of f2fs_gc is meaningless. So, let's
remove it.
2. Background GC marks victim blocks as dirty one at a time.
3. Foreground GC should do cleaning job until acquiring enough free
sections. Afterwards, it needs to do checkpoint.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Since, the memory for the object of dirty_seglist_info is allocated
using kzalloc - which returns zeroed out memory. So, there is no need
to initialize the nr_dirty values with zeroes.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Practically, has_not_enough_free_secs() should calculate with the numbers of
current node and directory data blocks together.
Actually the equation was implemented in need_to_flush().
So, this patch removes need_flush() and moves the equation into
has_not_enough_free_secs().
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch resolves a build warning reported by kbuild test robot.
"
fs/f2fs/segment.c: In function '__get_segment_type':
fs/f2fs/segment.c:806:1: warning: control reaches end of non-void
function [-Wreturn-type]
"
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
m68k allmodconfig:
fs/f2fs/data.c: In function ‘read_end_io’:
fs/f2fs/data.c:311: error: implicit declaration of function ‘prefetchw’
fs/f2fs/segment.c: In function ‘f2fs_end_io_write’:
fs/f2fs/segment.c:628: error: implicit declaration of function ‘prefetchw’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We should guarantee not to do *scheduling while atomic*.
I found, in atomic f2fs_end_io_write(), there is a set_page_dirty() call
to deal with IO errors.
But, set_page_dirty() calls:
-> f2fs_set_data_page_dirty()
-> set_dirty_dir_page()
-> cond_resched() which results in scheduling.
In order to avoid this, I'd like to remove simply set_page_dirty(),
since the page is already marked as ERROR and f2fs will be operated
as the read-only mode as well.
So, there is no recovery issue with this.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Do cleanup more for better code readability.
- Change the parameter set of f2fs_bio_alloc()
This function should allocate a bio only since it is not something like
f2fs_bio_init(). Instead, the caller should initialize the allocated bio.
- Introduce SECTOR_FROM_BLOCK
This macro translates a block address to its sector address.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>