Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added qlogic qed driver uses the zlib library, but
misses the dependency:
drivers/built-in.o: In function `qed_alloc_stream_mem':
drivers/net/ethernet/qlogic/qed/qed_main.c:707: undefined reference to `zlib_inflate_workspacesize'
drivers/built-in.o: In function `qed_unzip_data':
drivers/net/ethernet/qlogic/qed/qed_main.c:675: undefined reference to `zlib_inflateInit2'
This changes Kconfig to always select zlib when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver saves a copy of slaves' original mac address and then
assigns whatever mac as needed to the slave, depending on mode. In at
least modes 5 and 6 (balance-tlb, balance-alb), it often ends up being the
mac address of another slave. On release from the bond, the original mac
address is supposed to get restored via a dev_set_mac_address() call in
the bonding driver's __bond_release_one() function, which calls the
slave's ndo_set_mac_address function, which for qlcnic, is
qlcnic_set_mac().
Now, this function tries to be somewhat intelligent and exit early if
you're trying to set the mac address to the same thing that is already
set. The problem here is that adapter->mac_addr isn't in sync with
netdev->dev_addr. The qlcnic driver still has the original mac stored in
adapter->mac_addr, while the bonding driver has updated netdev->dev_addr,
so qlcnic thinks we're trying to set the same address it already has.
I think the way to go here, since the function updates both netdev and
adapter's stored mac addresses, is to check if either of them doesn't
match the newly requested mac. Simply checking netdev's value only could
result in a similar mismatch and non-update, so look at both.
CC: Dept-GELinuxNICDev@qlogic.com
CC: netdev@vger.kernel.org
CC: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success instead of -ENOMEM here.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
MODE_MF_SI is 9. We should be testing bit 9 instead of AND 0x9.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check if "p_hwfn" is NULL and then dereference it in the error
handling code. I read the code and it isn't NULL so let's remove the
check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only instance of a qlcnic_mbx_ops structure is never modified. Thus
the declaration of the structure and all references to the structure type
can be made const.
In the definition of the qlcnic_mailbox structure, the ops field is no
longer lined up with the other fields. This was left as is, to avoid a lot
of trivial changes on the other lines.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all cases, mbx->req.arg and mbx->rsp.arg have just been allocated
using kcalloc(), so these six memsets are redundant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates a large chunk of temporary buffer using kzalloc
to copy FW image. As there is no real need of this memory to be
physically contiguous, use vzalloc instead.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it is required to capture minidump for iSCSI functions
as part of default minidump collection process. To enable this, firmware
exports it's capability and driver need to enable that capability
by issuing a mailbox command.
With this feature, firmware can provide additional iSCSI function's
minidump with smaller minidump capture mask (0x1f).
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include local headers files after kernel's header files.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proper typecasting while performing byte-by-byte copy
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to memset memory allocated with vzalloc.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace confusing QL_STATUS_INVALID_PARAM == -1 == -EPERM with -EINVAL
and QLC_STATUS_UNSUPPORTED_CMD == -2 == -ENOENT with -EOPNOTSUPP, the
latter error code is arguable, but it is already used in the driver,
so let it be here as well.
Also remove always false (!buf) check on read(), the driver should
not care if userspace gets its EFAULT or not.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If read() syscall requests unexpected number of bytes from "dimm" binary
attribute file, return EINVAL instead of EPERM.
At the same time pin down sysfs file size to the fixed
sizeof(struct netxen_dimm_cfg), which allows to exploit some missing
sanity checks from kernfs (file boundary checks vs offset etc.)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
30 usecs (or really, 1 jiffy) can go by pretty fast.
Move the set of the timeout immediately before the loop.
Remove the unnecessary max(1ul, usecs_to_jiffies(30)) as
usecs_to_jiffies with a non-zero constant is guaranteed
to be non-zero.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch should have been part of the previous patch having the
same summary. See http://marc.info/?l=linux-kernel&m=143039470103795&w=2
Unfortunately, I didn't check to see where else this lock was used before
submitting that patch. This should take care of it for netxen_nic, as I
did a thorough search this time.
To recap from the original patch; although testing this driver with
DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled did not produce any traces,
it would be more prudent in the case of tx_clean_lock to use _bh
versions of spin_[un]lock, since this lock is manipulated in both
the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Acked-By: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'mutliple' to 'multiple'
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver keeps adding multicast addresses without deleting removed MACs and
worrying about adapters filter limit. This results into actual count of programmed
multicast addresses get accumulated over the time and overruns the adapter's
filter limit without putting device in ACCEPT_ALL_MULTI mode. This causes
newly added multicast traffic to fail after the sequence of addition - deletion
in certain pattern.
This issue is seen only when netdev's mcast list count is less than adapters
mcast filter limit.
e.g. If adapters multicast filter limit is 38 per function
then following sequence would result in multicast traffic failure for
newly added MACs.
- add less than 38 multicast MACs
- remove previously added multicast MACs
- add new multicast MACs (less than 38)
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions kfree() and vfree() perform also input parameter validation.
Thus the test around their calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Kalluru