Messages about PME# being supported and enabled/disabled are probably
useful for debug, but maybe don't need to be on the console.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jesse accidentally applied v1 [1] of the patchset instead of v2 [2]. This
is the diff between v1 and v2.
The changes in this patch are:
- tidied vsprintf stack buffer to shrink and compute size more
accurately
- use %pR for decoding and %pr for "raw" (with type and flags) instead
of adding %pRt and %pRf
[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Note: dom0 checking in v4 has been separated out into 2/2.
This patch enables P2P upstream forwarding in ACS capable PCIe switches.
It solves two potential problems in virtualization environment where a PCIe
device is assigned to a guest domain using a HW iommu such as VT-d:
1) Unintentional failure caused by guest physical address programmed
into the device's DMA that happens to match the memory address range
of other downstream ports in the same PCIe switch. This causes the PCI
transaction to go to the matching downstream port instead of go to the
root complex to get translated by VT-d as it should be.
2) Malicious guest software intentionally attacks another downstream
PCIe device by programming the DMA address into the assigned device
that matches memory address range of the downstream PCIe port.
We are in process of implementing device filtering software in KVM/XEN
management software to allow device assignment of PCIe devices behind a PCIe
switch only if it has ACS capability and with the P2P upstream forwarding bits
enabled. This patch is intended to work for both KVM and Xen environments.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Reviewed-by: Mathew Wilcox <willy@linux.intel.com>
Reviewed-by: Chris Wright <chris@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_dfl_cache_line_size is marked as __initdata but referenced by
pci_init() which is __devinit. Make it __devinitdata instead of
__initdata.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For non hotplug PCI devices, the system firmware usually configures
CLS correctly. For pccard devices system firmware can't do it and
Linux PCI layer doesn't do it either. Unfortunately this leads to
poor performance for certain devices (sata_sil). Unless MWI, which
requires separate configuration, is to be used, CLS doesn't affect
correctness, so the configuration should be harmless.
This patch makes pci_set_cacheline_size() always built and export it
and make pccard call it during attach.
Please note that some other PCI hotplug drivers (shpchp and pciehp)
also configure CLS on hotplug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Axel Birndt <towerlexa@gmx.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
sparc64 is now the only user of PCI_CACHE_LINE_BYTES. Drop it and set
pci_dfl_cache_line_size from pcibios_init() instead and drop
PCI_CACHE_LINE_BYTES handling from generic pci code.
Orignally-From: David Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES. Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right. On most configurations, the chance is that
firmware configures the correct value during boot.
This patch makes pci_init() determine CLS by looking at what firmware
has configured. It scans all devices and if all non-zero values
agree, the value is used. If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used. arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.
ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.
While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.infradead.org/~dwmw2/iommu-2.6.32:
x86: Move pci_iommu_init to rootfs_initcall()
Run pci_apply_final_quirks() sooner.
Mark pci_apply_final_quirks() __init rather than __devinit
Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c
intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space
intel-iommu: Decode (and ignore) RHSA entries
intel-iommu: Make "Unknown DMAR structure" message more informative
This function may have done more in the past, but all it does now is
apply the PCI_FIXUP_FINAL quirks. So name it sensibly and put it where
it belongs.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After attempting to change the power state of a PCI device
pci_raw_set_power_state() doesn't check if the value it wrote into
the device's PCI_PM_CTRL register has been stored in there, but
unconditionally modifies the device's current_state field to reflect
the change. This may cause problems to happen if the power state of
the device hasn't been changed in fact, because it will make the PCI
PM core make a wrong assumption.
To prevent such situations from happening modify
pci_raw_set_power_state() so that it reads the device's PCI_PM_CTRL
register after writing into it and uses the value read from the
register to update the device's current_state field. Also make it
print a message saying that the device refused to change its power
state as requested (returning an error code in such cases would cause
suspend regressions to appear on some systems, where device drivers'
suspend routines return error codes if pci_set_power_state() fails).
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some PCI devices fail if their standard configuration registers are
restored twice in a row. Prevent this from happening by making
pci_restore_state() clear the saved_state flag of the device right
after the device's standard configuration registers have been
populated with the previously saved values.
Simplify PCI PM callbacks by removing the direct clearing of
state_saved from them, as it shouldn't be necessary any more (except
in pci_pm_thaw(), where it has to be cleared, so that the values saved
during the "freeze" phase of hibernation are not used later by mistake).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce a new PCI device flag, wakeup_prepared, to prevent PCI
wake-up preparation code from being executed twice in a row for the
same device and for the same purpose.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework the PCI wake-up code so that it's easier to read without
changing the functionality.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In general a BIOS may goof or we may hotplug in a hotplug controller.
In either case the kernel needs to reserve resources for plugging
in more devices in the future instead of creating a minimal resource
assignment.
We already do this for cardbus bridges I am just adding a variant
for pcie bridges.
v2: Make testing for pcie hotplug bridges based on a flag.
So far we only set the flag for pcie but a header_quirk
could easily be added for the non-standard pci hotplug
bridges.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.
The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.
This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For many purposes, including interrupt-swizzling, devices with ARI
enabled behave as if they have one device (number 0) and 256 functions.
This probably hasn't bitten us in practice because all ARI devices I've
seen are also IOV devices, and IOV devices are required to use MSI.
This isn't guaranteed, and there are legitimate reasons to use ARI
without IOV, and hence potentially use pin-based interrupts.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For devices attached to the root bus, we can't trigger Secondary Bus
Reset because there is no bridge device associated with the bus. So
need to check bus->self again NULL first before using it.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
Other functions use type bool, so use that for pci_enable_wake as well.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a PCI device is not power-manageable either by the platform, or
with the help of the native PCI PM interface, pci_target_state() will
return either PCI_D3hot, or PCI_POWER_ERROR for it, depending on
whether or not the device is configured to wake up the system. Alas,
none of these return values is correct, because each of them causes
pci_prepare_to_sleep() to return error code, although it should
complete successfully in such a case.
Fix this problem by making pci_target_state() always return PCI_D0
for devices that cannot be power managed.
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI-to-PCI Bridge 1.2 specifies that the Secondary Bus Reset bit can
force the assertion of RST# on the secondary interface, which can be
used to reset all devices including subordinates under this bus. This
can be used to reset a function if this function is the only device
under this bus.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI PM 1.2 specifies that the device will perform an internal reset upon
transitioning from D3hot to D0 when the NO_SOFT_RESET bit is clear. This
method can be used to reset a function if neither PCIe FLR nor PCI AF FLR
are supported.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch enhances the FLR functions:
1) remove disable_irq() so the shared IRQ won't be disabled.
2) replace the 1s wait with 100, 200 and 400ms wait intervals
for the Pending Transaction.
3) replace mdelay() with msleep().
4) add might_sleep().
5) lock the device to prevent PM suspend from accessing the CSRs
during the reset.
6) coding style fixes.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_is_root_bus() in pci_common_swizzle() for checking if the pci
bus is root, for code consistency.
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_is_root_bus() in pci_get_interrupt_pin() for checking if the
pci bus is root, for code consistency.
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1235) adds an array of PCI power-state names, together
with a simple inline accessor routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC). This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.
The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).
Turning ECRC on or off can be a data integrity versus performance
tradeoff. In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
According to the PCI PM specification (PCI Bus Power Management
Interface Specification, Rev. 1.2, Section 5.4.1) we are supposed to
reinitialize devices that have PCI_PM_CTRL_NO_SOFT_RESET clear during
all transitions from PCI_D3hot to PCI_D0, but we only do it if the
device's current_state field is equal to PCI_UNKNOWN.
This may lead to problems if a device with PCI_PM_CTRL_NO_SOFT_RESET
unset is put into PCI_D3hot at run time by its driver and
pci_set_power_state() is used to put it back into PCI_D0, because in
that case the device will remain uninitialized after
pci_set_power_state() has returned. Prevent that from happening by
modifying pci_raw_set_power_state() to reinitialize devices with
PCI_PM_CTRL_NO_SOFT_RESET unset during all transitions from D3 to D0.
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Recent PCI PM changes introduced a bug that causes some devices to be
mishandled after kexec and during early initialization. The failure
scenario in the kexec case is the following:
* Assume a PCI device is not power-manageable by the platform and has
PCI_PM_CTRL_NO_SOFT_RESET set in PMCSR.
* The device is put into D3 before kexec (using the native PCI PM).
* After kexec, pci_setup_device() sets the device's power state to
PCI_UNKNOWN.
* pci_set_power_state(dev, PCI_D0) is called by the device's driver.
* __pci_start_power_transition(dev, PCI_D0) is called and since the
device is not power-manageable by the platform, it causes
pci_update_current_state(dev, PCI_D0) to be called. As a result
the device's current_state field is updated to PCI_D3, in
accordance with the contents of its PCI PM registers.
* pci_raw_set_power_state() is called and it changes the device power
state to D0. *However*, it should also call pci_restore_bars() to
reinitialize the device, but it doesn't, because the device's
current_state field has been modified earlier.
To prevent this from happening, modify pci_platform_power_transition()
so that it doesn't use pci_update_current_state() to update the
current_state field for devices that aren't power-manageable by the
platform. Instead, this field should be updated directly for devices
that don't support the native PCI PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe 1.1 base neither requires the endpoint to implement the entire
PCIe capability structure nor specifies default values of registers
that are not implemented by the device. So we only save and restore
registers that must be implemented by different device types if the
device PCIe capability version is 1.
PCIe 1.1 Capability Structure Expansion ECN and PCIe 2.0 requires
all registers in the PCIe capability to be either implemented or
hardwired to 0. Their PCIe capability version is 2.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
If the device is not supposed to wake up the system, ie. when
device_may_wakeup(&dev->dev) returns 'false', pci_prepare_to_sleep()
should pass 'false' to pci_enable_wake() so that it calls the
platform to disable the wake-up capability of the device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The radeonfb driver needs to program the device's PMCSR directly due
to some quirky hardware it has to handle (see
http://bugzilla.kernel.org/show_bug.cgi?id=12846 for details) and
after doing that it needs to call the platform (usually ACPI) to
finish the power transition of the device. Currently it uses
pci_set_power_state() for this purpose, however making a specific
assumption about the internal behavior of this function, which has
changed recently so that this assumption is no longer satisfied.
For this reason, introduce __pci_complete_power_transition() that may
be called by the radeonfb driver to complete the power transition of
the device. For symmetry, introduce __pci_start_power_transition().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a problem with PCI devices without any PM support (either
native or through the platform) that pci_set_power_state() always
returns error code for them, even if they are being put into D0.
However, such devices are always in D0, so pci_set_power_state()
should return success when attempting to put such a device into D0.
It also should update the current_state field for these devices as
appropriate. This modification is necessary so that the standard
configuration registers of these devices are successfully restored by
pci_restore_standard_config() during the "early" phase of resume.
In addition, pci_set_power_state() should check the value of
current_state before calling the platform to change the power state
of the device to avoid doing that unnecessarily.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move pci_restore_standard_config() from pci.c to pci-driver.c and
make it static.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Once we have allowed timer interrupts to be enabled during the early
phase of resuming devices, we are now able to use the generic
pci_set_power_state() to put PCI devices into D0 at that time. Then,
the platform-specific PM code will have a chance to handle devices
that don't implement the native PCI PM or that require some
additional, platform-specific operations to be carried out to power
them up. Also, by doing this we can simplify the code quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe 2.0 defines several new registers (Device Control 2, Link Control 2,
and Slot Control 2). Save and retore them in pci_save_pcie_state() and
pci_restore_pcie_state().
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Restore the volatile registers in the SR-IOV capability after the
D3->D0 transition.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a device has the SR-IOV capability, initialize it (set the ARI
Capable Hierarchy in the lowest numbered PF if necessary; calculate
the System Page Size for the VF MMIO, probe the VF Offset, Stride
and BARs). A lock for the VF bus allocation is also initialized if
a PF is the lowest numbered PF.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch allows memory resources to be assigned with a specified
alignment at boot-time or run-time. The patch is useful when we use PCI
pass-through, because page-aligned memory resources are required to
securely share PCI resources with guest drivers.
If you want to assign the resource at boot time, please set
"pci=resource_alignment=" boot parameter.
This is format of "pci=resource_alignment=" boot parameter:
[<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
Specifies alignment and device to reassign
aligned memory resources.
If <order of align> is not specified, PAGE_SIZE is
used as alignment.
PCI-PCI bridge can be specified, if resource
windows need to be expanded.
This is example:
pci=resource_alignment=20@07:00.0;18@0f:00.0;00:1d.7
If you want to assign the resource at run-time, please set
"/sys/bus/pci/resource_alignment" file, and hot-remove the device and
hot-add the device. For this purpose, fakephp or PCI hotplug interfaces
can be used.
The format of "/sys/bus/pci/resource_alignment" file is the same with
boot parameter. You can use "," instead of ";".
For example:
# cd /sys/bus/pci
# echo -n 20@12:00.0 > resource_alignment
# echo 1 > devices/0000:12:00.0/remove
# echo 1 > rescan
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pci_common_swizzle() seems to have a assumption that
pci_bus->self is NULL on the pci root bus. But it might not be true on
some platforms. Because of this wrong assumption, pci_common_swizzle()
might cause endless loop. We must check pci_bus->parent instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pci_get_interrupt_pin() seems to have an assumption that
pci_bus->self is NULL on the root pci bus. But it might not be true on
some platforms. Because of this wrong assumption, current
pci_get_interrupt_pin() might cause endless loop. We must check
pci_bus->parent instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For all devices need to do function level reset, currently we need wait for
at least 200ms, which can be too long if we have lots of devices...
The patch checked pending bit before msleep() to skip some unnecessary
sleeping interval.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>